I am using kernel 2.0.27, libraries, etc. coming from redhat-4.1.
Monitors' settings should be correct: I copied them from the manual...
X -probeonly says:
---------------------------------------------------------------------------
XFree86 Version 3.2 / X Window System
(protocol Version 11, revision 0, vendor release 6100)
Release Date: Oct 26 1996
If the server is older than 6-12 months, or if your card is newer
than the above date, look for a newer version before reporting
problems. (see http://www.XFree86.Org/FAQ)
Operating System: Linux [ELF]
Configured drivers:
S3: accelerated server for S3 graphics adaptors (Patchlevel 0)
mmio_928, s3_generic, newmmio
(using VT number 7)
XF86Config: /usr/X11R6/lib/X11/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: keymap: "xfree86(us)" (overrides other XKB settings)
(**) Mouse: type: PS/2, device: /dev/mouse, baudrate: 1200
(**) S3: Graphics device ID: "Number Nine FX Vision 330"
(**) S3: Monitor ID: "My Monitor"
(**) FontPath set to "/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/75dpi/:unscaled,/usr/X11R6/lib/X11/fonts/100dpi/:unscaled,/usr/X11R6/lib/X11/fonts/Type1/,/usr/X11R6/lib/X11/fonts/Speedo/,/usr/X11R6/lib/X11/fonts/75dpi/,/usr/X11R6/lib/X11/fon
ts/100dpi/"
(--) S3: PCI: base address not correctly aligned or address conflict
base address changed from 0x01800000 to 0xf8000000
(--) S3: PCI: Trio32/64 rev 0, Linear FB @ 0xf8000000
(--) S3: card type: PCI
(--) S3: chipset: Trio64 rev. 201
(--) S3: chipset driver: mmio_928
(--) S3: videoram: 2048k
(--) S3: Ramdac type: s3_trio64
(--) S3: Ramdac speed: 135
(--) S3: Using Trio32/64 programmable clock (MCLK 57.273 MHz)
(--) S3: Maximum allowed dot-clock: 135.000 MHz
(**) S3: Mode "640x480": mode clock = 31.500
(**) S3: Mode "800x600": mode clock = 50..000
(**) S3: Mode "1024x768": mode clock = 85.000
(**) S3: Mode "1280x1024": mode clock = 135.000
(--) S3: Operating RAMDAC in pixel multiplex mode
(--) S3: Using 6 bits per RGB value
(--) S3: Virtual resolution set to 1280x1024
--------------------------------------------------------------------------
/proc/pci is:
--------------------------------------------------------------------------
PCI devices found:
Bus 0, device 14, function 0:
Ethernet controller: DEC DC21040 (rev 36).
Medium devsel. Fast back-to-back capable. IRQ 15. Master Capable. Latency=255.
I/O at 0xb000.
Non-prefetchable 32 bit memory at 0x1000000.
Bus 0, device 13, function 0:
VGA compatible controller: S3 Inc. Trio32/Trio64 (rev 0).
Medium devsel.
Non-prefetchable 32 bit memory at 0xf8000000.
Bus 0, device 7, function 0:
Non-VGA device: Intel 82378IB (rev 67).
Medium devsel. Master Capable. No bursts.
Bus 0, device 6, function 0:
SCSI storage controller: NCR 53c810 (rev 17).
Medium devsel. IRQ 11. Master Capable. Latency=255. Min Gnt=8.Max Lat=64.
I/O at 0xb400.
Non-prefetchable 32 bit memory at 0x2000000.
------------------------------------------------------------------------------
Thanks.
Paolo