2.3.29 kernel, boot failure with modprobe error

From: Shailesh K Basani (shailesh@icp.siemens.com)
Date: Wed Mar 15 2000 - 14:25:25 EST


HI,

I am trying to boot 2.3.29 kernel on a Redhat 6.2 system with
the following hardware:

2 Intel Pentium Pro CPUs, ncr53c8xx - version 3.2a-2
(Siemens Primergy Box)

I have modutils-2.3.9.

(My SCSI driver is set to Y, ELF is set Y in the config)

The other h/w info is in the log below. The boot fails with the
messages as seen below.

The system boots up fine with 2.2.12, 2.2.13 etc kernels.
When I recompiled it with 2.3.29 I run into these problems.
I played with the config options with no success.

Please let me know if anyone has any ideas. I would really appreciate
it. Thanks a lot for your help.

LILO boot:
Loading linux-29...................
Linux version 2.3.29 (root@bock) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #11 SMP Tue Mar 14 19:16:57 PST 2000
e820: 0009f400 @ 00000000 (usable)
e820: 00000c00 @ 0009f400 (reserved)
e820: 00010000 @ 000f0000 (reserved)
e820: 0ff00000 @ 00100000 (usable)
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at 01012240
Intel MultiProcessor Specification v1.4
    Virtual Wire compatibility mode.
OEM ID: SNID1031 Product ID: PRIMERGY APIC at: 0xFEE00000
Processor #1 Pentium(tm) Pro APIC version 17
    Floating point unit present.
    Machine Exception supported.
    64 bit compare & exchange supported.
    Internal APIC present.
    Bootup CPU
Processor #0 Pentium(tm) Pro APIC version 17
    Floating point unit present.
    Machine Exception supported.
    64 bit compare & exchange supported.
    Internal APIC present.
Bus #0 is PCI
Bus #1 is PCI
Bus #2 is PCI
Bus #3 is ISA
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 2
mapped APIC to ffffe000 (fee00000)
mapped IOAPIC to ffffd000 (fec00000)
totalpages: 00010000
zone(0): 4096 pages.
zone(1): 61440 pages.
zone(2): 0 pages.
Detected 347220139 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 346.52 BogoMIPS
Memory: 254796k/262144k available (1312k kernel code, 6960k reserved, 128k data, 168k init, 0k highmem)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
VFS: Diskquotas version dquot_6.4.0 initialized
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
per-CPU timeslice cutoff: 100.06 usecs.
CPU1: Intel Pentium II (Deschutes) stepping 02
Getting VERSION: 40011
Getting VERSION: 40011
Getting LVT0: 700
Getting LVT1: 400
enabled ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
CPU map: 3
Booting processor 0 eip 2000
Setting warm reset code and vector.
1.
2.
3.
Asserting INIT.
Deasserting INIT.
Sending STARTUP #1.
After apic_write.
Startup point 1.
Initializing CPU#0
Waiting for send to finish...
CPU#0 waiting for CALLOUT
+Sending STARTUP #2.
After apic_write.
Startup point 1.
Waiting for send to finish...
+After Startup.
Before Callout 0.
After Callout 0.
CALLIN, before setup_local_APIC().
masked ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 346.52 BogoMIPS
Stack at about c148bfbc
OK.
CPU0: Intel Pentium II (Deschutes) stepping 02
CPU has booted.
Before bogomips.
Total of 2 processors activated (693.04 BogoMIPS).
Before bogocount - setting activated=1.
Boot done.
ENABLING IO-APIC IRQs
init IO_APIC IRQs
 IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23, 2-24, 2-25, 2-26, 2-27, 2-28, 2-29, 2-30, 2-31 not connected.
activating NMI Watchdog ... done.
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 32.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 001F0011
....... : max redirection entries: 001F
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
 00 000 00 1 0 0 0 0 0 0 00
 01 0FF 0F 0 0 0 0 0 1 1 59
 02 0FF 0F 0 0 0 0 0 1 1 51
 03 0FF 0F 0 0 0 0 0 1 1 61
 04 0FF 0F 0 0 0 0 0 1 1 69
 05 0FF 0F 1 1 0 0 0 1 1 71
 06 0FF 0F 0 0 0 0 0 1 1 79
 07 0FF 0F 0 0 0 0 0 1 1 81
 08 0FF 0F 0 0 0 0 0 1 1 89
 09 0FF 0F 1 1 0 0 0 1 1 91
 0a 0FF 0F 1 1 0 0 0 1 1 99
 0b 0FF 0F 1 1 0 0 0 1 1 A1
 0c 0FF 0F 0 0 0 0 0 1 1 A9
 0d 000 00 1 0 0 0 0 0 0 00
 0e 0FF 0F 0 0 0 0 0 1 1 B1
 0f 0FF 0F 1 1 0 0 0 1 1 B9
 10 000 00 1 0 0 0 0 0 0 00
 11 000 00 1 0 0 0 0 0 0 00
 12 000 00 1 0 0 0 0 0 0 00
 13 000 00 1 0 0 0 0 0 0 00
 14 000 00 1 0 0 0 0 0 0 00
 15 000 00 1 0 0 0 0 0 0 00
 16 000 00 1 0 0 0 0 0 0 00
 17 000 00 1 0 0 0 0 0 0 00
 18 000 00 1 0 0 0 0 0 0 00
 19 000 00 1 0 0 0 0 0 0 00
 1a 000 00 1 0 0 0 0 0 0 00
 1b 000 00 1 0 0 0 0 0 0 00
 1c 000 00 1 0 0 0 0 0 0 00
 1d 000 00 1 0 0 0 0 0 0 00
 1e 000 00 1 0 0 0 0 0 0 00
 1f 000 00 1 0 0 0 0 0 0 00
.................................... done.
Initializing CPU#1
calibrating APIC timer ...
..... CPU clock speed is 347.2136 MHz.
..... host bus clock speed is 99.2036 MHz.
cpu: 0, clocks: 992036, slice: 330678, nr: 2.
CPU0<C0:992032,C:330672,D:4,S:330678,C:992036>
cpu: 1, clocks: 992036, slice: 330678, nr: 1.
CPU1<C0:992032,C:661344,D:10,S:330678,C:992036>
checking TSC synchronization across CPUs: passed.
Setting commenced=1, go go go
PCI: PCI BIOS revision 2.10 entry at 0xfd9fc
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Interrupt Routing Table found at 0xc00fded0 [router type 0000/0000]
PCI: Cannot allocate resource region 0 of device 00:04.0
PCI: Cannot allocate resource region 2 of device 00:04.0
PCI: Allocation of memory region 00:04.0/0 (-19922944 bytes) failed
PCI: Allocation of memory region 00:04.0/2 (-18874368 bytes) failed
isapnp: Scanning for Pnp cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.3
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (established 16384 bind 16384)
Initializing RT netlink socket
apm: BIOS not found.
Starting kswapd v1.6
Detected PS/2 Mouse Port.
Serial driver version 4.91 (1999-11-17) with MANY_PORTS SHARE_IRQ SERIAL_PCI PCI_IOMEM enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.21
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
scsi : 0 hosts.
scsi : detected total.
Partition check:
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 4194302k freed
Real Time Clock Driver v1.09b
ACPI: found PIIX4 at 0xf0c0
Linux PCMCIA Card Services 3.1.4
  options: [pci] [cardbus] [apm]
Intel PCIC probe: not found.
ds: no socket drivers loaded!
VFS: Mounted root (ext2 filesystem).
kmod: failed to exec /sbin/modprobe -s -k binfmt-0000, errno = 2
kmod: failed to exec /sbin/modprobe -s -k binfmt-0000, errno = 2
kmod: failed to exec /sbin/modprobe -s -k block-major-8, errno = 2
VFS: Cannot open root device 08:01
Kernel panic: VFS: Unable to mount root fs on 08:01
NMI Watchdog detected LOCKUP on CPU0, registers:
CPU: 0
EIP: 0010:[<c0110456>]
EFLAGS: 00000002
eax: c148a000 ebx: 00000000 ecx: c0110430 edx: 00000000
esi: 00000000 edi: c02ee140 ebp: 00000000 esp: c148bf74
ds: 0018 es: 0018 ss: 0018
Process swapper (pid: 0, stackpage=c148b000)
Stack: c148a000 c148a000 c020630a c148a000 00000000 00000000 c148a000 c02ee140
       00000000 00000000 00000018 00000018 00000041 c0108511 00000010 00000246
       00000000 00000000 00000000 c0270e44 00000001 c010a2e4 00000000 00000000
Call Trace: [<c020630a>] [<c0108511>] [<c010a2e4>] [<c0119d17>]
Code: eb fd eb fe 89 f6 6a 00 6a 01 6a 00 68 30 04 11 c0 e8 08 fe
console shuts up ...

regards,
shailesh

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/



This archive was generated by hypermail 2b29 : Thu Mar 23 2000 - 21:00:17 EST