I just trying tu use the UltraDMA mode of my drivers. My motherboard it's a
SOYO 5EHM ( VP3 chipset, well really a ETEQ) lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT82C597 [Apollo VP3] (rev 04)
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP]
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C586 ISA [Apollo VP] (rev 41)
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 06)
00:07.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 02)
00:07.3 Host bridge: VIA Technologies, Inc. VT82C586B ACPI (rev 10)
Well, my hda it's a Wester Digital of 8.4G. At least the specs say it can do
UDMA. I actived it in the BIOS and I have the next error:
<SNIP>
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
ide0: VIA Bus-Master (U)DMA Timing Config Success
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
ide1: VIA Bus-Master (U)DMA Timing Config Success
hda: WDC WD84AA, ATA DISK drive
hdb: CRD-8400C, ATAPI CDROM drive
hdc: FUJITSU M1638TAU, ATA DISK drive
hdd: Traxdata CDRW2260+, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: WDC WD84AA, 8063MB w/2048kB Cache, CHS=1027/255/63, UDMA
hdc: FUJITSU M1638TAU, 2452MB w/128kB Cache, CHS=4983/16/63, DMA
Freeing unused kernel memory: 40k freed
>>> This is the error
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: DMA disabled
hdb: DMA disabled
ide0: reset: success
Adding Swap: 136512k swap-space (priority -1)
Adding Swap: 68508k swap-space (priority -2)
The IDE interdce have also a CDROM attached. The kernel I have been tested
it's a 2.2.15pre9.
I'm a bit scared about the lenght of the IDE cables, because mine are near 75
cm long. Could be this the problem :?
Thanks in advance
Drizzt
--
... El departamento de informática les desea un feliz 1900.
____________________________________________________________________________
Drizzt Do'Urden Three rings for the Elves Kings under the Sky
drizzt.dourden@iname.com Seven for the Dwarf_lords in their
hall of stone
Nine for the Mortal Men doomed to die
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Fri Mar 31 2000 - 21:00:18 EST