My tulip card don't work with ac15&16 (2.4.0.test1 do)
I got this on the console
Serial driver version 5.01 (2000-05-29) with MANY_PORTS SHARE_IRQ
SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
ttyS02 at 0x03e8 (irq = 4) is a 16550A
ttyS03 at 0x02e8 (irq = 3) is a 16550A
PPP generic driver version 2.4.1
Linux Tulip driver version 0.9.6 (May 31, 2000)
eth0,0,0,0: Digital DS21140 Tulip rev 34 at 0xa800, 00:C0:95:E0:1F:74,
IRQ 18.
eth0,0,0,0: EEPROM default media type Autosense.
eth0,0,0,0: Index #0 - Media 10baseT (#0) described by a 21140 non-MII
(0) block.
eth0,0,0,0: Index #1 - Media 100baseTx (#3) described by a 21140
non-MII (0) block.
eth0,0,0,0: MII transceiver #1 config 3000 status 7829 advertising
01e1.
eth0,0,0,0: Advertising 0001 on PHY 1, previously advertising 01e1.
eth0,0,0,0: Advertising 0001 (to advertise is 0200).
eth1,0,0,0: Digital DS21140 Tulip rev 34 at 0xa400, 00:C0:95:E0:1F:75,
IRQ 19.
eth1,0,0,0: EEPROM default media type Autosense.
eth1,0,0,0: Index #0 - Media 10baseT (#0) described by a 21140 non-MII
(0) block.
eth1,0,0,0: Index #1 - Media 100baseTx (#3) described by a 21140
non-MII (0) block.
eth1,0,0,0: MII transceiver #1 config 3000 status 7829 advertising
01e1.
eth1,0,0,0: Advertising 0001 on PHY 1, previously advertising 01e1.
eth1,0,0,0: Advertising 0001 (to advertise is 0200).
eth2,0,0,0: Digital DS21140 Tulip rev 34 at 0xa000, 00:C0:95:E0:1F:76,
IRQ 16.
eth2,0,0,0: EEPROM default media type Autosense.
eth2,0,0,0: Index #0 - Media 10baseT (#0) described by a 21140 non-MII
(0) block.
eth2,0,0,0: Index #1 - Media 100baseTx (#3) described by a 21140
non-MII (0) block.
eth2,0,0,0: MII transceiver #1 config 3000 status 7809 advertising
01e1.
eth2,0,0,0: Advertising 0001 on PHY 1, previously advertising 01e1.
eth2,0,0,0: Advertising 0001 (to advertise is 0200).
eth3,0,0,0: Digital DS21140 Tulip rev 34 at 0x9800, 00:C0:95:E0:1F:77,
IRQ 17.
eth3,0,0,0: EEPROM default media type Autosense.
eth3,0,0,0: Index #0 - Media 10baseT (#0) described by a 21140 non-MII
(0) block.
eth3,0,0,0: Index #1 - Media 100baseTx (#3) described by a 21140
non-MII (0) block.
eth3,0,0,0: MII transceiver #1 config 3000 status 7809 advertising
01e1.
eth3,0,0,0: Advertising 0001 on PHY 1, previously advertising 01e1.
eth3,0,0,0: Advertising 0001 (to advertise is 0200).
[drm] Initialized tdfx 0.0.1 19991009 on minor 63
Linux PCMCIA Card Services 3.1.11
But there are no devices found with ifconfig. The same view with
2.4.0.test1 shows
PPP generic driver version 2.4.1
Linux Tulip driver version 0.9.4.3 (Apr 14, 2000)
eth0: Digital DS21140 Tulip rev 34 at 0xa800, 00:C0:95:E0:1F:74, IRQ 18.
eth0: EEPROM default media type Autosense.
eth0: Index #0 - Media 10baseT (#0) described by a 21140 non-MII (0)
block.
eth0: Index #1 - Media 100baseTx (#3) described by a 21140 non-MII (0)
block.
eth0: MII transceiver #1 config 3000 status 7829 advertising 01e1.
eth1: Digital DS21140 Tulip rev 34 at 0xa400, 00:C0:95:E0:1F:75, IRQ 19.
eth1: EEPROM default media type Autosense.
eth1: Index #0 - Media 10baseT (#0) described by a 21140 non-MII (0)
block.
eth1: Index #1 - Media 100baseTx (#3) described by a 21140 non-MII (0)
block.
eth1: MII transceiver #1 config 3000 status 7829 advertising 01e1.
eth2: Digital DS21140 Tulip rev 34 at 0xa000, 00:C0:95:E0:1F:76, IRQ 16.
eth2: EEPROM default media type Autosense.
eth2: Index #0 - Media 10baseT (#0) described by a 21140 non-MII (0)
block.
eth2: Index #1 - Media 100baseTx (#3) described by a 21140 non-MII (0)
block.
eth2: MII transceiver #1 config 3000 status 7809 advertising 01e1.
eth3: Digital DS21140 Tulip rev 34 at 0x9800, 00:C0:95:E0:1F:77, IRQ 17.
eth3: EEPROM default media type Autosense.
eth3: Index #0 - Media 10baseT (#0) described by a 21140 non-MII (0)
block.
eth3: Index #1 - Media 100baseTx (#3) described by a 21140 non-MII (0)
block.
eth3: MII transceiver #1 config 3000 status 7809 advertising 01e1.
[drm] Initialized tdfx 0.0.1 19991009 on minor 63
Linux PCMCIA Card Services 3.1.11
options: [pci] [cardbus]
Databook TCIC-2 PCMCIA probe: not found.
kmem_create: Forcing size word alignment - nfs_fh
ds: no socket drivers loaded!
Note the numbers in the devicename for the non working.
Very similar to the append string in my lilo.
append="ether=0,0,eth0,0,0,0 ether=0,0,eth1,0,0,0 ether=0,0,eth2,0,0,0
ether=0,0,eth3,0,0,0"
My guess is that it asume only 3 arguments for the ether parameter.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Thu Jun 15 2000 - 21:00:26 EST