On Wed, 11 Oct 2000, Linus Torvalds wrote:
> What happens if MTRR support is entirely disabled?
If MTRR support is disabled then both eepro100 interfaces work fine but
the system is still 40x slower. This is the entire bootlog of
2.4.0-test10-pre1 + lspci-vvx + /proc/interrupts + /proc/iomem + ifconfig
output
Two currently active ideas (from Mark, Linus and Zoltan):
a) one needs to use big-mtrr patch from Zoltan, look at e820 map and
manually set up mtrrs to cover all 6G.
b) this is an L2 cache-tag issue and there is just not enough bits in the
tag to cover such high addresses so nothing will help, save removing the
extra 2G or so out of the machine (or using them as MTD devices :(((( I
hope this is _not_ the case...
another idea (in parallel) is that eepro100 stops working because its PCI
memory space is marked as cacheable.
All should become clear soon -- I will spend the whole day on this, slowly
trying to understand what's going on.
Regards,
Tigran
Linux version 2.4.0-test9 (root@hilbert) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #15 SMP Wed Oct 11 19:23:15 BST 2000
BIOS-provided physical RAM map:
BIOS-e820: 000000000009fc00 @ 0000000000000000 (usable)
BIOS-e820: 0000000000000400 @ 000000000009fc00 (reserved)
BIOS-e820: 0000000000020000 @ 00000000000e0000 (reserved)
BIOS-e820: 00000000fccf0000 @ 0000000000100000 (usable)
BIOS-e820: 000000000000f000 @ 00000000fcdf0000 (ACPI data)
BIOS-e820: 0000000000001000 @ 00000000fcdff000 (ACPI NVS)
BIOS-e820: 0000000000001000 @ 00000000fec00000 (reserved)
BIOS-e820: 0000000000001000 @ 00000000fee00000 (reserved)
BIOS-e820: 0000000000080000 @ 00000000fff80000 (reserved)
BIOS-e820: 0000000080000000 @ 0000000100000000 (usable)
5248MB HIGHMEM available.
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at 000fb4d0
hm, page 000fb000 reserved twice.
hm, page 000fc000 reserved twice.
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
On node 0 totalpages: 1572864
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 1343488 pages.
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: AMI Product ID: CNB20HE APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
Bootup CPU
Processor #1 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
Processor #2 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
Processor #3 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
Bus #0 is PCI
Bus #1 is PCI
Bus #2 is PCI
Bus #3 is ISA
I/O APIC #4 Version 17 at 0xFEC00000.
I/O APIC #5 Version 17 at 0xFEC01000.
Int: type 0, pol 3, trig 3, bus 0, IRQ 04, APIC ID 5, APIC INT 0a
Int: type 0, pol 3, trig 3, bus 0, IRQ 08, APIC ID 5, APIC INT 0b
Int: type 0, pol 3, trig 3, bus 0, IRQ 0c, APIC ID 5, APIC INT 0f
Int: type 0, pol 3, trig 3, bus 0, IRQ 3c, APIC ID 4, APIC INT 0a
Int: type 0, pol 3, trig 3, bus 1, IRQ 15, APIC ID 5, APIC INT 01
Int: type 0, pol 3, trig 3, bus 1, IRQ 14, APIC ID 5, APIC INT 00
Int: type 3, pol 1, trig 1, bus 3, IRQ 00, APIC ID 4, APIC INT 00
Int: type 0, pol 1, trig 1, bus 3, IRQ 01, APIC ID 4, APIC INT 01
Int: type 0, pol 1, trig 1, bus 3, IRQ 00, APIC ID 4, APIC INT 02
Int: type 0, pol 1, trig 1, bus 3, IRQ 03, APIC ID 4, APIC INT 03
Int: type 0, pol 1, trig 1, bus 3, IRQ 04, APIC ID 4, APIC INT 04
Int: type 0, pol 1, trig 1, bus 3, IRQ 06, APIC ID 4, APIC INT 06
Int: type 0, pol 1, trig 1, bus 3, IRQ 07, APIC ID 4, APIC INT 07
Int: type 0, pol 1, trig 1, bus 3, IRQ 08, APIC ID 4, APIC INT 08
Int: type 0, pol 1, trig 1, bus 3, IRQ 0c, APIC ID 4, APIC INT 0c
Int: type 0, pol 1, trig 1, bus 3, IRQ 0d, APIC ID 4, APIC INT 0d
Int: type 0, pol 1, trig 1, bus 3, IRQ 0e, APIC ID 4, APIC INT 0e
Int: type 0, pol 1, trig 1, bus 3, IRQ 0f, APIC ID 4, APIC INT 0f
Lint: type 3, pol 1, trig 1, bus 3, IRQ 00, APIC ID ff, APIC LINT 00
Lint: type 1, pol 1, trig 1, bus 0, IRQ 00, APIC ID ff, APIC LINT 01
Processors: 4
mapped APIC to ffffe000 (fee00000)
mapped IOAPIC to ffffd000 (fec00000)
mapped IOAPIC to ffffc000 (fec01000)
Kernel command line: auto BOOT_IMAGE=240-test10 ro root=805 BOOT_FILE=/boot/vmlinuz-2.4.0-test10 console=ttyS0,9600 console=tty0
Initializing CPU#0
Detected 701.611 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1399.19 BogoMIPS
Memory: 6132848k/6291456k available (1531k kernel code, 106956k reserved, 88k data, 188k init, 5322688k highmem)
Dentry-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Buffer-cache hash table entries: 524288 (order: 9, 2097152 bytes)
Page-cache hash table entries: 524288 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU0: Intel Pentium III (Cascades) stepping 01
per-CPU timeslice cutoff: 2927.55 usecs.
Getting VERSION: 40011
Getting VERSION: 40011
Getting ID: 0
Getting ID: f000000
Getting LVT0: 700
Getting LVT1: 400
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000004
ESR value after enabling vector: 00000000
CPU present map: f
Booting processor 1/1 eip 2000
Setting warm reset code and vector.
1.
2.
3.
Asserting INIT.
Waiting for send to finish...
+Deasserting INIT.
Waiting for send to finish...
+#startup loops: 2.
Sending STARTUP #1.
After apic_write.
Startup point 1.
Initializing CPU#1
Waiting for send to finish...
CPU#1 (phys ID: 1) waiting for CALLOUT
+Sending STARTUP #2.
After apic_write.
Startup point 1.
Waiting for send to finish...
+After Startup.
Before Callout 1.
After Callout 1.
CALLIN, before setup_local_APIC().
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1402.47 BogoMIPS
Stack at about c766bfbc
OK.
CPU1: Intel Pentium III (Cascades) stepping 01
CPU has booted.
Booting processor 2/2 eip 2000
Setting warm reset code and vector.
1.
2.
3.
Asserting INIT.
Waiting for send to finish...
+Deasserting INIT.
Waiting for send to finish...
+#startup loops: 2.
Sending STARTUP #1.
After apic_write.
Startup point 1.
Initializing CPU#2
Waiting for send to finish...
CPU#2 (phys ID: 2) waiting for CALLOUT
+Sending STARTUP #2.
After apic_write.
Startup point 1.
Waiting for send to finish...
+After Startup.
Before Callout 2.
After Callout 2.
CALLIN, before setup_local_APIC().
masked ExtINT on CPU#2
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1402.47 BogoMIPS
Stack at about c767dfbc
OK.
CPU2: Intel Pentium III (Cascades) stepping 01
CPU has booted.
Booting processor 3/3 eip 2000
Setting warm reset code and vector.
1.
2.
3.
Asserting INIT.
Waiting for send to finish...
+Deasserting INIT.
Waiting for send to finish...
+#startup loops: 2.
Sending STARTUP #1.
After apic_write.
Startup point 1.
Initializing CPU#3
Waiting for send to finish...
CPU#3 (phys ID: 3) waiting for CALLOUT
+Sending STARTUP #2.
After apic_write.
Startup point 1.
Waiting for send to finish...
+After Startup.
Before Callout 3.
After Callout 3.
CALLIN, before setup_local_APIC().
masked ExtINT on CPU#3
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1402.47 BogoMIPS
Stack at about c767bfbc
OK.
CPU3: Intel Pentium III (Cascades) stepping 01
CPU has booted.
Before bogomips.
Total of 4 processors activated (5606.60 BogoMIPS).
Before bogocount - setting activated=1.
Boot done.
ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 4 ... ok.
...changing IO-APIC physical APIC ID to 5 ... ok.
Synchronizing Arb IDs.
..TIMER: vector=49 pin1=2 pin2=0
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found pin 0) ...works.
activating NMI Watchdog ... done.
testing the IO APIC.......................
.................................... done.
calibrating APIC timer ...
..... CPU clock speed is 701.6077 MHz.
..... host bus clock speed is 100.2296 MHz.
cpu: 0, clocks: 1002296, slice: 200459
CPU0<T0:1002288,T1:801824,D:5,S:200459,C:1002296>
cpu: 1, clocks: 1002296, slice: 200459
cpu: 2, clocks: 1002296, slice: 200459
cpu: 3, clocks: 1002296, slice: 200459
CPU1<T0:1002288,T1:601360,D:10,S:200459,C:1002296>
CPU2<T0:1002288,T1:400896,D:15,S:200459,C:1002296>
CPU3<T0:1002288,T1:200448,D:4,S:200459,C:1002296>
checking TSC synchronization across CPUs: passed.
Setting commenced=1, go go go
PCI: PCI BIOS revision 2.10 entry at 0xfdbb1, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ServerWorks host bridge: secondary bus 01
PCI: ServerWorks host bridge: secondary bus 00
PCI->APIC IRQ transform: (B1,I5,P0) -> 16
PCI->APIC IRQ transform: (B1,I5,P1) -> 17
PCI->APIC IRQ transform: (B0,I1,P0) -> 26
PCI->APIC IRQ transform: (B0,I2,P0) -> 27
PCI->APIC IRQ transform: (B0,I3,P0) -> 31
PCI->APIC IRQ transform: (B0,I15,P0) -> 10
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 65536 buckets, 512Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
P6 Microcode Update Driver v1.07
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PCI_IDE: unknown IDE controller on PCI bus 00 device 79, VID=1166, DID=0211
PCI_IDE: chipset revision 0
PCI_IDE standard IDE storage device detected
hda: CREATIVE CD5233E, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 52X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.11
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10c
Non-volatile memory driver v1.1
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
eepro100.c: $Revision: 1.33 $ 2000/05/24 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
eth0: OEM i82557/i82558 10/100 Ethernet, 00:30:48:00:36:EC, IRQ 31.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 000d80-134, Physical connectors present:
Primary interface chip i82553-A/B PHY #8.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
Receiver lock-up workaround activated.
eth1: Intel Corporation 82557 [Ethernet Pro 100], 00:D0:B7:23:B4:77, IRQ 26.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 721383-008, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
SCSI subsystem driver Revision: 1.00
(scsi0) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter> found at PCI 1/5/0
(scsi0) Wide Channel A, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 392 instructions downloaded
(scsi1) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter> found at PCI 1/5/1
(scsi1) Wide Channel B, SCSI ID=7, 32/255 SCBs
(scsi1) Downloading sequencer code... 392 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.1/5.2.0
<Adaptec AIC-7899 Ultra 160/m SCSI host adapter>
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.1/5.2.0
<Adaptec AIC-7899 Ultra 160/m SCSI host adapter>
(scsi0:0:0:0) Synchronous at 160.0 Mbyte/sec, offset 63.
Vendor: IBM Model: DPSS-336950M Rev: S80D
Type: Direct-Access ANSI SCSI revision: 03
(scsi0:0:1:0) Synchronous at 160.0 Mbyte/sec, offset 63.
Vendor: IBM Model: DPSS-336950M Rev: S80D
Type: Direct-Access ANSI SCSI revision: 03
(scsi0:0:2:0) Synchronous at 160.0 Mbyte/sec, offset 63.
Vendor: IBM Model: DPSS-336950M Rev: S80D
Type: Direct-Access ANSI SCSI revision: 03
Vendor: SUPER Model: GEM354 REV001 Rev: 1.04
Type: Processor ANSI SCSI revision: 02
(scsi1:0:0:0) Synchronous at 160.0 Mbyte/sec, offset 63.
Vendor: IBM Model: DPSS-336950M Rev: S80D
Type: Direct-Access ANSI SCSI revision: 03
(scsi1:0:1:0) Synchronous at 160.0 Mbyte/sec, offset 63.
Vendor: IBM Model: DPSS-336950M Rev: S80D
Type: Direct-Access ANSI SCSI revision: 03
(scsi1:0:2:0) Synchronous at 160.0 Mbyte/sec, offset 63.
Vendor: IBM Model: DPSS-336950M Rev: S80D
Type: Direct-Access ANSI SCSI revision: 03
Vendor: SUPER Model: GEM354 REV001 Rev: 1.04
Type: Processor ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
Detected scsi disk sdc at scsi0, channel 0, id 2, lun 0
Detected scsi disk sdd at scsi1, channel 0, id 0, lun 0
Detected scsi disk sde at scsi1, channel 0, id 1, lun 0
Detected scsi disk sdf at scsi1, channel 0, id 2, lun 0
SCSI device sda: 72170880 512-byte hdwr sectors (36951 MB)
Partition check:
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
sda3: <bsd: sda8 sda9 >
SCSI device sdb: 72170880 512-byte hdwr sectors (36951 MB)
sdb: unknown partition table
SCSI device sdc: 72170880 512-byte hdwr sectors (36951 MB)
sdc: unknown partition table
SCSI device sdd: 72170880 512-byte hdwr sectors (36951 MB)
sdd: unknown partition table
SCSI device sde: 72170880 512-byte hdwr sectors (36951 MB)
sde: unknown partition table
SCSI device sdf: 72170880 512-byte hdwr sectors (36951 MB)
sdf: unknown partition table
Detected scsi generic sg3 at scsi0, channel 0, id 8, lun 0, type 3
Detected scsi generic sg7 at scsi1, channel 0, id 8, lun 0, type 3
kmem_create: Forcing size word alignment - nfs_fh
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 188k freed
keyboard: Timeout - AT keyboard not present?
lspci -vvx
===========
00:00.0 Host bridge: ServerWorks CNB20HE (rev 21)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00: 66 11 08 00 00 00 00 00 21 00 00 06 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:00.1 Host bridge: ServerWorks CNB20HE (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64, cache line size 08
00: 66 11 08 00 07 00 00 22 01 00 00 06 08 40 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:00.2 Host bridge: ServerWorks: Unknown device 0006
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
00: 66 11 06 00 02 00 00 22 00 00 00 06 08 40 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:00.3 Host bridge: ServerWorks: Unknown device 0006
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
00: 66 11 06 00 02 00 00 22 00 00 00 06 08 40 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:01.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] (rev 08)
Subsystem: Intel Corporation EtherExpress PRO/100+ Management Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 26
Region 0: Memory at fe9ed000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at c400 [size=64]
Region 2: Memory at fde00000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at fdd00000 [disabled] [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00: 86 80 29 12 17 01 90 02 08 00 00 02 08 40 00 00
10: 00 d0 9e fe 01 c4 00 00 00 00 e0 fd 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 0c 00
30: 00 00 d0 fd dc 00 00 00 00 00 00 00 0b 01 08 38
00:02.0 VGA compatible controller: S3 Inc. 86c764/765 [Trio32/64/64V+] (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 27
Region 0: Memory at fe000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at fe9f0000 [disabled] [size=64K]
00: 33 53 11 88 03 00 00 02 00 00 00 03 00 00 00 00
10: 00 00 00 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 9f fe 00 00 00 00 00 00 00 00 0b 01 00 00
00:03.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] (rev 08)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 31
Region 0: Memory at fe9ee000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at c800 [size=64]
Region 2: Memory at fe800000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at fdf00000 [disabled] [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00: 86 80 29 12 17 01 90 02 08 00 00 02 08 40 00 00
10: 00 e0 9e fe 01 c8 00 00 00 00 80 fe 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 f0 fd dc 00 00 00 00 00 00 00 05 01 08 38
00:0f.0 ISA bridge: ServerWorks OSB4 (rev 4f)
Subsystem: ServerWorks OSB4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 66 11 00 02 07 00 00 02 4f 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 66 11 00 02
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0f.1 IDE interface: ServerWorks: Unknown device 0211 (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at ffa0 [size=16]
00: 66 11 11 02 05 00 00 02 00 8a 01 01 00 40 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: a1 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0f.2 USB Controller: ServerWorks: Unknown device 0220 (rev 04) (prog-if 10 [OHCI])
Subsystem: ServerWorks: Unknown device 0220
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe9ef000 (32-bit, non-prefetchable) [size=4K]
00: 66 11 20 02 17 01 80 02 04 10 03 0c 08 40 80 00
10: 00 f0 9e fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 66 11 20 02
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 50
01:05.0 SCSI storage controller: Adaptec 7899P (rev 01)
Subsystem: Super Micro Computer Inc: Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (10000ns min, 6250ns max), cache line size 08
Interrupt: pin A routed to IRQ 16
BIST result: 00
Region 0: I/O ports at d400 [size=256]
Region 1: Memory at feafe000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at feaa0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 05 90 cf 00 07 00 b0 02 01 00 00 01 08 40 80 80
10: 01 d4 00 00 04 e0 af fe 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 d9 15 01 00
30: 00 00 aa fe dc 00 00 00 00 00 00 00 0b 01 28 19
01:05.1 SCSI storage controller: Adaptec 7899P (rev 01)
Subsystem: Super Micro Computer Inc: Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (10000ns min, 6250ns max), cache line size 08
Interrupt: pin B routed to IRQ 17
BIST result: 00
Region 0: I/O ports at d800 [size=256]
Region 1: Memory at feaff000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 05 90 cf 00 07 00 b0 02 01 00 00 01 08 40 80 80
10: 01 d8 00 00 04 f0 af fe 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 d9 15 01 00
30: 00 00 ac fe dc 00 00 00 00 00 00 00 09 02 28 19
cat /proc/iomem
===============
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000c8000-000c8fff : Extension ROM
000c9000-000cefff : Extension ROM
000f0000-000fffff : System ROM
00100000-fcdeffff : System RAM
00100000-0027edf7 : Kernel code
0027edf8-0029509f : Kernel data
fcdf0000-fcdfefff : ACPI Tables
fcdff000-fcdfffff : ACPI Non-volatile Storage
fde00000-fdefffff : Intel Corporation 82557 [Ethernet Pro 100]
fe000000-fe7fffff : S3 Inc. 86c764/765 [Trio32/64/64V+]
fe800000-fe8fffff : Intel Corporation 82557 [Ethernet Pro 100] (#2)
fe9ed000-fe9edfff : Intel Corporation 82557 [Ethernet Pro 100]
fe9ed000-fe9edfff : eepro100
fe9ee000-fe9eefff : Intel Corporation 82557 [Ethernet Pro 100] (#2)
fe9ee000-fe9eefff : eepro100
fe9ef000-fe9effff : PCI device 1166:0220 (ServerWorks)
feafe000-feafefff : Adaptec 7899P
feaff000-feafffff : Adaptec 7899P (#2)
fec00000-fec00fff : reserved
fee00000-fee00fff : reserved
fff80000-ffffffff : reserved
ifconfig
========
eth0 Link encap:Ethernet HWaddr 00:30:48:00:36:EC
inet addr:192.168.4.6 Bcast:192.168.4.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:9 errors:0 dropped:0 overruns:0 frame:0
TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:31
eth1 Link encap:Ethernet HWaddr 00:D0:B7:23:B4:77
inet addr:192.168.3.6 Bcast:192.168.3.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:26 Base address:0x2000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16192 Metric:1
RX packets:6 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
cat /proc/interrupts
====================
CPU0 CPU1 CPU2 CPU3
0: 9502 9042 8782 10706 IO-APIC-edge timer
1: 233 195 193 217 IO-APIC-edge keyboard
2: 0 0 0 0 XT-PIC cascade
8: 0 0 1 0 IO-APIC-edge rtc
12: 0 0 0 0 IO-APIC-edge PS/2 Mouse
13: 0 0 0 0 XT-PIC fpu
14: 0 0 2 2 IO-APIC-edge ide0
16: 443 425 518 554 IO-APIC-level aic7xxx
17: 28 27 26 26 IO-APIC-level aic7xxx
26: 4 5 6 6 IO-APIC-level eth1
31: 33 54 39 49 IO-APIC-level eth0
NMI: 37558 37558 37558 37558
LOC: 37413 37476 37477 37087
ERR: 0
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sun Oct 15 2000 - 21:00:22 EST