With the purpose of having two printers connected to my Linux server I
bought a PCI (single port) parallel port card thinking that installation
would be straightforward.
Parport was already compiled into the kernel (version 2.2.17), and lp is
a module.
After looking at the output from 'lspci -vvx' (see below) I added
'append="parport=0x278,auto parport=0x7c00,11"' to lilo.conf and
rebooted, this far everything was looking good since parport even
managed to retrieve the printer info from the new card (lp1):
<text during bootup>
parport0: PC-style at 0x278 [SPP,PS2,EPP]
parport_probe: failed
parport0: no IEEE-1284 device present.
parport1: PC-style at 0x7c00, irq 11 [SPP,PS2]
parport_probe: succeeded
parport1: Printer, Hewlett-Packard HP LaserJet 1100
Now, as soon as I try to print to /dev/lp1 the box locks up hard
(without any oops messages), moving the printer to lp0 and changing only
the device in /etc/printcap allows me to print just fine.
By looking at the windows drivers provided with the card I came to the
conclusion that the onboard chip was an Oxford Semiconductor OX16PCI954
which as far as I could understand is documented in
http://www.oxsemi.com/products/uarts/ox16pci954/ox16pci954ds.pdf. I've
also searched the previous LKML archives for any posts about this
chipset and all I could find was an older post
(http://lists.insecure.org/linux-kernel/2000/Sep/0071.html) from Tim
Waugh <twaugh@redhat.com> claiming to add support for this chipset.
Looking at 2.2.18-pre25 I couldn't see that the patch had been included
though and as far as I could understand (with my limited knowledge of C)
the patch only added the PCI id's to the kernel.
Now, what can I do to solve this problem? (If any info is missing,
please just ask)
Thanks in advance,
David Härdeman
<lspci -vvx>
00:0c.0 Communication controller: Titan Electronics Inc: Unknown device
ffff
Subsystem: Oxford Semiconductor Ltd: Unknown device 0000
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Region 0: I/O ports at 7400
Region 1: Memory at e4102000 (32-bit, non-prefetchable)
Region 2: I/O ports at 7800
Region 3: Memory at e4103000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0+,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: d2 14 ff ff 03 00 90 02 00 00 80 07 00 00 80 00
10: 01 74 00 00 00 20 10 e4 01 78 00 00 00 30 10 e4
20: 00 00 00 00 00 00 00 00 00 00 00 00 15 14 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 00 00 00
00:0c.1 Parallel controller: Titan Electronics Inc: Unknown device a000
(prog-if 01 [BiDir])
Subsystem: Oxford Semiconductor Ltd: Unknown device 0000
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 7c00
Region 1: I/O ports at 8000
Region 2: I/O ports at 8400
Region 3: Memory at e4104000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0+,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: d2 14 00 a0 03 00 90 02 00 01 01 07 00 00 80 00
10: 01 7c 00 00 01 80 00 00 01 84 00 00 00 40 10 e4
20: 00 00 00 00 00 00 00 00 00 00 00 00 15 14 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Fri Dec 15 2000 - 21:00:16 EST