FIC AD11(AMD 761/VIA 686B) AGP port not supported

From: Joshua Corbin (jcorbin@linuxmail.org)
Date: Fri May 18 2001 - 09:21:09 EST

Next message: Jes Sorensen: "Re: Linux kernel programming for beginners"
Previous message: Stephen C. Tweedie: "Re: LANANA: To Pending Device Number Registrants"
Next in thread: Alan Cox: "Re: FIC AD11(AMD 761/VIA 686B) AGP port not supported"
Reply: Alan Cox: "Re: FIC AD11(AMD 761/VIA 686B) AGP port not supported"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

The Motherboard is a FIC AD11(AMD 761/VIA 686B chipset). Vid-card is a radeon 32M ddr model.

Whenever I startx with the radeon driver, the machine hangs, forced to use reset switch, not even C-A-Del works. But with the generic vga driver I get all of 16 colors at less than 640x480.

Here are relevant dmesg lines:
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: Unsupported AMD chipset (device id: 700e), you might want to try agp_try_unsupported=1.
agpgart: no supported devices found.

What does agp_try_unsupported mean? Where do I set this setting?

and relevant lspci:
00:00.0 Host bridge: Advanced Micro Devices [AMD]: Unknown device 700e (rev 12)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 32 set
        Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
        Region 1: Memory at e3100000 (32-bit, prefetchable) [size=4K]
        Region 2: I/O ports at d000 [disabled] [size=4]
        Capabilities: [a0] AGP version 2.0
                Status: RQ=15 SBA+ 64bit- FW+ Rate=421
                Command: RQ=0 SBA- AGP- 64bit- FW- Rate=

00:01.0 PCI bridge: Advanced Micro Devices [AMD]: Unknown device 700f
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 set
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
        I/O behind bridge: 0000c000-0000cfff
        Memory behind bridge: e0000000-e1ffffff
        Prefetchable memory behind bridge: d8000000-dfffffff
        BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-

Also attached are the full dmesg and lspci output.

Please help, as it is I am force to use windows to get anything done (that too needed updated drivers before it would work properly).

Thanks in advance -- Josh

Get your free email from www.linuxmail.org

Powered by Outblaze - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/

Next message: Jes Sorensen: "Re: Linux kernel programming for beginners"
Previous message: Stephen C. Tweedie: "Re: LANANA: To Pending Device Number Registrants"
Next in thread: Alan Cox: "Re: FIC AD11(AMD 761/VIA 686B) AGP port not supported"
Reply: Alan Cox: "Re: FIC AD11(AMD 761/VIA 686B) AGP port not supported"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

This archive was generated by hypermail 2b29 : Wed May 23 2001 - 21:00:27 EST