Re: ide-convert-9 oops on boot

From: Heinz Diehl (
Date: Sat May 04 2002 - 03:45:02 EST

On Sat May 04 2002, J.A. Magallon wrote:

> Just patched pre8 with ide-convert-9, and system hangs on boot:

Exactly the same thing here. You're not alone ;)

Journalled Block Device driver loaded
Real Time Clock Driver v1.10e
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c586b (rev 41) IDE UDMA33 controller on pci00:07.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
hda: IBM-DHEA-36481, ATA DISK drive
hdb: Conner Peripherals 1275MB - CFS1275A, ATA DISK drive
hdc: CD-540E, ATAPI CD/DVD-ROM drive
hdd: CD-W54E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 12692736 sectors (6499 MB) w/472KiB Cache, CHS=790/255/63, UDMA(33)
hdb: 2496876 sectors (1278 MB) w/64KiB Cache, CHS=619/64/63, DMA

chiara:~ # lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3] (rev 04)
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP]
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C586/A/B PCI-to-ISA [Apollo
VP] (rev 41)
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 06)
00:07.3 Host bridge: VIA Technologies, Inc. VT82C586B ACPI (rev 10)
00:11.0 VGA compatible controller: S3 Inc. ViRGE/DX or /GX (rev 01)

chiara:~ cat /proc/ide/via

----------VIA BusMastering IDE Configuration----------------
Driver Version: 3.34
South Bridge: VIA vt82c586b
Revision: ISA 0x41 IDE 0x6
Highest DMA rate: UDMA33
BM-DMA base: 0xe000
PCI clock: 33.3MHz
Master Read Cycle IRDY: 1ws
Master Write Cycle IRDY: 1ws
BM IDE Status Register Read Retry: yes
Max DRDY Pulse Width: No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush: yes yes
End Sector FIFO flush: no no
Prefetch Buffer: yes yes
Post Write Buffer: yes no
Enabled: yes yes
Simplex only: no no
Cable Type: 40w 40w
Transfer Mode: UDMA DMA UDMA DMA
Address Setup: 30ns 30ns 30ns 30ns
Cmd Active: 90ns 90ns 90ns 90ns
Cmd Recovery: 30ns 30ns 30ns 30ns
Data Active: 90ns 90ns 90ns 90ns
Data Recovery: 30ns 30ns 30ns 30ns
Cycle Time: 60ns 120ns 60ns 120ns
Transfer Rate: 33.3MB/s 16.6MB/s 33.3MB/s 16.6MB/s

# Heinz Diehl, 68259 Mannheim, Germany
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to
More majordomo info at
Please read the FAQ at

This archive was generated by hypermail 2b29 : Tue May 07 2002 - 22:00:22 EST