ethernet tulip misdetected starting 2.5.20

From: Albert Cranford (ac9410@bellsouth.net)
Date: Mon Jun 03 2002 - 19:43:01 EST


2.5.19 works while 2.5.20 has mostly correct lspci output (PME- instead of PME+)
but the wrong driver gets detected and fails loading.
Similar to 3c509 vs 3c590 from Anton.
Anyone have any ideas in troubleshooting this?
Config:
CONFIG_NET_TULIP=y
# CONFIG_DE2104X is not set
CONFIG_TULIP=m
# CONFIG_TULIP_MWI is not set
# CONFIG_TULIP_MMIO is not set
# CONFIG_DE4X5 is not set

              linux-2.5.19
dmesg
Linux Tulip driver version 1.1.13 (May 11, 2002)
PCI: Found IRQ 11 for device 00:0b.0
eth0: ADMtek Comet rev 17 at 0xe800, 00:03:6D:16:4E:39, IRQ 11.

lspci -vv
00:0b.0 Ethernet controller: Bridgecom, Inc: Unknown device 0985 (rev 11)
        Subsystem: Bridgecom, Inc: Unknown device 0574
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 255 min, 255 max, 32 set, cache line size 08
        Interrupt: pin A routed to IRQ 11
        Region 0: I/O ports at e800 [size=256]
        Region 1: Memory at e3001000 (32-bit, non-prefetchable) [size=1K]
        Expansion ROM at <unassigned> [disabled] [size=128K]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME+
                Status: D0 PME-Enable- DSel=0 DScale=0 PME+

------------------
             linux-2.5.20
dmesg
Linux Tulip driver version 1.1.13 (May 11, 2002)
PCI: Found IRQ 11 for device 00:0b.0
tulip0: MII transceiver #1 config 1000 status 786d advertising 01e1.
eth0: Digital DS21140 Tulip rev 17 at 0xe800, EEPROM not present, 00:4C:69:6E:75:79, IRQ 11.

lspci -vv
00:0b.0 Ethernet controller: Bridgecom, Inc: Unknown device 0985 (rev 11)
        Subsystem: Bridgecom, Inc: Unknown device 0574
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 255 min, 255 max, 32 set, cache line size 08
        Interrupt: pin A routed to IRQ 11
        Region 0: I/O ports at e800 [size=256]
        Region 1: Memory at e3001000 (32-bit, non-prefetchable) [size=1K]
        Expansion ROM at <unassigned> [disabled] [size=128K]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME+
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

-- 
Albert Cranford Deerfield Beach FL USA
ac9410@bellsouth.net
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/



This archive was generated by hypermail 2b29 : Fri Jun 07 2002 - 22:00:17 EST