I'm running 2.4.19 with a Promise TX2 Ultra133, but even though the card BIOS reports
UDMA mode 5/6 on the drives, they are reported as UDMA33 by the kernel.
Trying hdparm -X69 after boot gives the message "Speed warnings UDMA 3/4/5 is not functional."
The IBM drive is only ATA100, but the Maxtor (just fitted) is definitely ATA133.
Any ideas?
Unfortunately, I'm running with XFS, so I'm a bit restricted in what kernel versions I can run.
Thanks,
Barrie
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PDC20269: IDE controller on PCI bus 00 dev 70
PDC20269: chipset revision 2
PDC20269: not 100% native mode: will probe irqs later
PDC20269: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER
Mode.
ide2: BM-DMA at 0x1000-0x1007, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0x1008-0x100f, BIOS settings: hdg:pio, hdh:pio
PIIX4: IDE controller on PCI bus 00 dev 91
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x10a0-0x10a7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x10a8-0x10af, BIOS settings: hdc:pio, hdd:pio
hda: IBM-DTTA-371440, ATA DISK drive
hde: IC35L080AVVA07-0, ATA DISK drive
hdg: MAXTOR 6L080J4, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0x10c0-0x10c7,0x10b6 on irq 18
ide3 at 0x10b8-0x10bf,0x10b2 on irq 18
hda: 28229040 sectors (14453 MB) w/462KiB Cache, CHS=28005/16/63, UDMA(33)
hde: 160836480 sectors (82348 MB) w/1863KiB Cache, CHS=159560/16/63,
UDMA(33)
hdg: 156355584 sectors (80054 MB) w/1819KiB Cache, CHS=155114/16/63,
UDMA(33)
hda: hda1
hde: hde1
hdg: unknown partition table
:
:
ide3: Speed warnings UDMA 3/4/5 is not functional.
ide2: Speed warnings UDMA 3/4/5 is not functional.
# hdparm -i /dev/hde
/dev/hde:
Model=IC35L080AVVA07-0, FwRev=VA4OA50K, SerialNo=VNC400A4G8VSSA
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1863kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=160836480
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
AdvancedPM=yes: disabled (255)
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5
# hdparm -i /dev/hdg
/dev/hdg:
Model=MAXTOR 6L080J4, FwRev=A93.0500, SerialNo=664212156696
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=32256, SectSize=21298, ECCbytes=4
BuffType=DualPortCache, BuffSize=1819kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=156355584
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5 udma6
AdvancedPM=no
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-1 ATA-2 ATA-3 ATA-4
ATA-5
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Fri Aug 23 2002 - 22:00:27 EST