ide, ide_scsi problems in 2.4.20-pre11

From: lk@trolloc.com
Date: Tue Nov 05 2002 - 22:19:30 EST

Next message: Bill Leckey: "kfree_skb query"
Previous message: Jeff Dike: "Re: 2.4.20-rc1 - hang with processes stuck in D"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

I have been having problems with a Plextor CD-R connected to a PDC20268
(Promise Ultra-100TX) using the ide_scsi driver since the driver first
appeared. It's been improving, but as of 2.4.20-pre7-ac3, I'm still
having problems. The card is in a 33Mhz slot on a Micronics W6LI board.

When I write to the drive (hdg, seen as scsi ID 0) with cdrecord, it will
write successfully for some time (usually 30 MB or more, sometimes even
completing a write), whereas in older kernels it would fail between 1-4
MB.

In earlier 2.4.20-pre kernels, the PDC20268 drivers would report timeouts
resetting the card upon rebooting, and the only way to regain control of
the CD-R was to power the machine down. This seems to have been fixed
along the way.

Below is pertinant information. The system completely hangs, but there is
no kernel oops.

/proc/ide/hdg/media
cdrom

/proc/ide/hdg/model
PLEXTOR CD-R PX-W2410A

/proc/ide/hdg/settings
name value min max
mode
---- ----- --- ---

---- bios_cyl 0 0 1023 rw bios_head 0 0 255 rw bios_sect 0 0 63 rw current_speed 0 0 69 rw ide_scsi 0 0 1 rw init_speed 0 0 69 rw io_32bit 0 0 3 rw keepsettings 0 0 1 rw log 0 0 1 rw nice1 1 0 1 rw number 2 0 3 rw pio_mode write-only 0 255 w slow 0 0 1 rw transform 1 0 3 rw unmaskirq 0 0 1 rw using_dma 0 0 1 rw

Controller / IDE info: ------------------------- Oct 28 22:53:04 sdsl-64-7-1-79 kernel: ide_setup: hdg=ide-scsi Oct 28 22:53:04 sdsl-64-7-1-79 kernel: PDC20268: IDE controller on PCI bus 00 dev 88 Oct 28 22:53:04 sdsl-64-7-1-79 kernel: PDC20268: chipset revision 1 Oct 28 22:53:04 sdsl-64-7-1-79 kernel: PDC20268: not 100%% native mode: will probe irqs later Oct 28 22:53:04 sdsl-64-7-1-79 kernel: PDC20268: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER Mode. Oct 28 22:53:04 sdsl-64-7-1-79 kernel: ide2: BM-DMA at 0xece0-0xece7, BIOS settings: hde:DMA, hdf:pio Oct 28 22:53:04 sdsl-64-7-1-79 kernel: ide3: BM-DMA at 0xece8-0xecef, BIOS settings: hdg:pio, hdh:pio Oct 28 22:53:04 sdsl-64-7-1-79 kernel: hda: IBM-DTTA-371010, ATA DISK drive Oct 28 22:53:04 sdsl-64-7-1-79 kernel: hde: IBM-DTLA-307045, ATA DISK drive Oct 28 22:53:04 sdsl-64-7-1-79 kernel: hdg: PLEXTOR CD-R PX-W2410A, ATAPI CD/DVD-ROM drive Oct 28 22:53:04 sdsl-64-7-1-79 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Oct 28 22:53:04 sdsl-64-7-1-79 kernel: ide2 at 0xecc8-0xeccf,0xecda on irq 17 Oct 28 22:53:04 sdsl-64-7-1-79 kernel: ide3 at 0xecd0-0xecd7,0xecde on irq 17

Syslog before system hangs completely (no oops!) ---------------------------- Oct 28 22:53:54 linux kernel: Uniform CD-ROM driver Revision: 3.12 Oct 28 22:57:47 linux kernel: cdrom: This disc doesn't have any tracks I recognize! Oct 28 22:59:00 linux kernel: cdrom: This disc doesn't have any tracks I recognize! Oct 28 22:59:32 linux last message repeated 16 times Oct 28 23:01:21 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:31 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:31 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:31 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:31 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:31 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:31 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:32 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:32 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:32 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:32 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:32 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:32 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:33 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:33 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:33 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:33 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:33 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:33 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:34 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:34 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:34 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:34 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:34 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:34 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:35 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:35 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:35 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:35 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:35 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:35 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:36 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:36 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:36 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:36 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:36 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:36 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:37 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:37 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:37 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:37 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:37 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:37 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:38 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:38 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:38 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:38 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:38 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:38 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:39 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:39 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:39 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:39 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:39 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:39 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:40 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:40 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:40 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:40 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:40 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:40 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:41 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:41 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:41 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:41 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:41 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:41 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:42 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:42 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:42 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:42 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:42 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:42 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:43 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:43 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:43 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:43 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:43 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:43 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:44 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:44 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:44 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:44 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:44 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:44 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:45 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:45 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:45 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:45 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:45 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:45 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:46 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:46 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:46 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:46 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:46 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:46 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:47 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:47 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:47 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:47 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:47 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:47 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:48 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:48 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:48 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:48 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:48 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:48 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:49 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:49 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:49 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:49 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:49 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:49 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:50 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:50 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:50 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:50 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:50 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:50 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:50 linux kernel: scsi : aborting command due to timeout : pid 3529, scsi0, channel 0, id 0, lun 0 Write (10) 00 00 00 08 3c 00 00 1f 00 Oct 28 23:01:50 linux kernel: hdg: lost interrupt Oct 28 23:01:51 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:51 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:51 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:51 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:51 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:51 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:52 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:52 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:52 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:52 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:52 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:52 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:53 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:53 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:53 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:53 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:53 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:53 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:54 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:54 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:54 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:54 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:54 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:54 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:55 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:55 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:55 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:55 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:55 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:55 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:56 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:56 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:56 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:56 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:56 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:56 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:57 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:57 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:57 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:57 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:57 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:57 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:58 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:58 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:58 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:58 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:58 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:58 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:59 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:59 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:59 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:01:59 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:01:59 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:01:59 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:02:00 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:02:00 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:02:00 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:02:00 linux kernel: scsi : aborting command due to timeout : pid 3530, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Oct 28 23:02:00 linux kernel: SCSI host 0 abort (pid 3530) timed out - resetting Oct 28 23:02:00 linux kernel: SCSI bus is being reset for host 0 channel 0. Oct 28 23:02:00 linux kernel: hdg: lost interrupt Oct 28 23:02:00 linux kernel: hdg: lost interrupt Oct 28 23:02:00 linux kernel: ide-scsi: scatter gather table too small, padding with zeros Oct 28 23:02:00 linux kernel: hdg: lost interrupt Oct 28 23:02:00 linux kernel: ide-scsi: scatter gather table too small, padding with zeros Oct 28 23:02:00 linux kernel: hdg: lost interrupt Oct 28 23:02:00 linux kernel: ide-scsi: scatter gather table too small, padding with zeros Oct 28 23:02:00 linux kernel: hdg: lost interrupt Oct 28 23:02:00 linux kernel: ide-scsi: scatter gather table too small, padding with zeros Oct 28 23:02:00 linux kernel: hdg: lost interrupt Oct 28 23:02:00 linux kernel: ide-scsi: scatter gather table too small, padding with zeros Oct 28 23:02:00 linux kernel: hdg: lost interrupt Oct 28 23:02:00 linux kernel: ide-scsi: scatter gather table too small, padding with zeros Oct 28 23:02:00 linux kernel: hdg: lost interrupt Oct 28 23:02:00 linux kernel: ide-scsi: scatter gather table too small, padding with zeros Oct 28 23:02:00 linux kernel: hdg: lost interrupt Oct 28 23:02:00 linux kernel: ide-scsi: scatter gather table too small, padding with zeros Oct 28 23:02:00 linux kernel: hdg: lost interrupt Oct 28 23:02:00 linux kernel: ide-scsi: scatter gather table too small, padding with zeros Oct 28 23:02:00 linux kernel: hdg: lost interrupt Oct 28 23:02:00 linux kernel: ide-scsi: scatter gather table too small, padding with zeros Oct 28 23:02:00 linux kernel: hdg: lost interrupt Oct 28 23:02:01 linux kernel: ide-scsi: scatter gather table too small, padding with zeros Oct 28 23:02:01 linux kernel: hdg: lost interrupt Oct 28 23:02:01 linux kernel: ide-scsi: scatter gather table too small, padding with zeros Oct 28 23:02:01 linux kernel: hdg: lost interrupt Oct 28 23:07:26 linux syslogd 1.4.1: restart.

- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/

Next message: Bill Leckey: "kfree_skb query"
Previous message: Jeff Dike: "Re: 2.4.20-rc1 - hang with processes stuck in D"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

This archive was generated by hypermail 2b29 : Thu Nov 07 2002 - 22:00:41 EST