Hi,
Are you using the modules from the kernel source or from pcmcia-cs? Are
you using yenta_socket or pcmcia-cs? pcmcia-cs has given me a lot more
positive results than trying to use yenta_socket and the built in kernel
modules. Also, try binding your card IDs to use wavelan_cs instead and
see if it works (maybe those cards are a bit older and as such need
older drivers.)
Also see if /sbin/iwconfig (hopefully you have this gem installed, it's
wireless-tools by Jean Tourrilhes @
http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html) gives
you any useful information. Is it picking up an AP?
Finally, ACPI might not make a difference, but see if enabling or
disabling APM does.
Hope this helps you.
Regards
-Josh
I have nearly the same setup as you
Rabid cheeseburgers forced Alexander Hoogerhuis<alexh@ihatent.com> to
write this on 24 Dec 2002 18:10:29+0100:
> Since very early 2.4 somewhere it has been impossible to use my two
> wireless cards, a NetGear ME401 and a Lucent card (both
> orinoco-based). Both are able to load the modules when pluggen in, but
> trying to use them is futile, as nothing gets transmitted, and dmesg
> show tons of this:
>
> eth1: Station identity 001f:0006:0001:0003
> eth1: Looks like an Intersil firmware version 1.03
> eth1: Ad-hoc demo mode supported
> eth1: IEEE standard IBSS ad-hoc mode supported
> eth1: WEP supported, 104-bit key
> eth1: MAC address 00:09:5B:27:DC:F9
> eth1: Station name "Prism I"
> eth1: ready
> eth1: index 0x01: Vcc 5.0, irq 6, io 0x0100-0x013f
> NETDEV WATCHDOG: eth1: transmit timed out
> eth1: Tx timeout! Resetting card. ALLOCFID=0128, TXCOMPLFID=0127,
> EVSTAT=800c eth1: Error -110 writing packet to BAP
> eth1: Error -110 writing Tx descriptor to BAP
> eth1: Error -110 writing Tx descriptor to BAP
> NETDEV WATCHDOG: eth1: transmit timed out
> eth1: Tx timeout! Resetting card. ALLOCFID=0128, TXCOMPLFID=0127,
> EVSTAT=800c
>
> The situation is similar for both cars, and I'm wondering if this is
> a known broken setup, or I've messed up?
>
> Currnently I'm on 2.4.20, tried both with and without the ACPI and
> preempt patches (vmware deosnt make a difference either), the hardware
> is a Compaq Evo n800c notebook and this is the cardbus bridge:
>
> 02:06.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus
> Controller (rev 02)
> Subsystem: Compaq Computer Corporation: Unknown device 004a
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF-
> FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
> <PERR- Latency: 168, cache line size 20
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at 40000000 (32-bit, non-prefetchable)
> [size=4K] Bus: primary=02, secondary=03, subordinate=03,
> sec-latency=176 Memory window 0: 30400000-307ff000
> (prefetchable) Memory window 1: 30800000-30bff000
> I/O window 0: 00004800-000048ff
> I/O window 1: 00004c00-00004cff
> BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+
> PostWrite+ 16-bit legacy interface ports at 0001
>
> mvh,
> A
> --
> Alexander Hoogerhuis | alexh@ihatent.com
> CCNP - CCDP - MCNE - CCSE | +47 908 21 485
> "You have zero privacy anyway. Get over it." --Scott McNealy
> -
> To unsubscribe from this list: send the line "unsubscribe
> linux-kernel" in the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
-- Joshua Kwan joshk@mspencer.net pgp public key at http://joshk.mspencer.net/pubkey_gpg.asc
This archive was generated by hypermail 2b29 : Tue Dec 31 2002 - 22:00:08 EST