[1.] Tyan TIGER MPX won't boot 2.5.64 (2.4.20 runs fine)
[2.] I have a new Tyan TIGER MPX motherboard with two AMD Athlon MP
2200+ CPUs. Linux 2.4.20 runs fine (configured SMP). However, 2.5.64
will not boot. When I try, the machine freezes up with the following
displayed on the screen (transcribed by hand onto another machine):
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Machine check exception polling timer started.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instructioon... OK.
POSIX conformance testing by UNIFIX
CPU0: AMD Athlon(tm) MP 2200+ stepping 00
per-CPU timeslice cutoff: 731.49 usecs.
task migration cache decay timeout: 1 msecs.
masked ExtINT on CPU#0
Leaving ESR disabled.
Booting processor 1/1 eip 2000
Storing NMI vector
APIC never delivered???
APIC delivery error (4)l.
CPU #1 not responding - cannot use it.
Booting processor 1/2 eip 2000
Storing NMI vector
APIC never delivered???
APIC delivery error (4).
CPU #2 not responding - cannot use it.
Error: only one processor found.
ENABLING IO-APIC IRQs
[3.] keywords: kernel, SMP
[4.] Kernel version 2.5.64
[5.]
[6.]
[7.]
[7.1.]
as reported under 2.4.20:
Linux vanzandt 2.4.20 #11 SMP Sat Mar 15 18:43:27 EST 2003 i686 unknown
Gnu C 2.95.4
Gnu make 3.79.1
util-linux 2.11n
mount 2.11n
module-init-tools writing
e2fsprogs 1.27
PPP 2.4.1
Linux C Library 2.3.1
Dynamic linker (ldd) 2.3.1
Procps 2.0.7
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 2.0.11
Modules Loaded i2c-dev i2c-core
[7.2.] As reported by 2.4.20 kernel:
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 8
model name : AMD Athlon(tm) MP 2200+
stepping : 0
cpu MHz : 1800.079
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
bogomips : 3591.37
processor : 1
vendor_id : AuthenticAMD
cpu family : 6
model : 8
model name : AMD Athlon(tm) Processor
stepping : 0
cpu MHz : 1800.079
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
bogomips : 3591.37
[7.3.]
[7.4.]
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial(set)
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(set)
0cf8-0cff : PCI conf1
1000-10ff : Adaptec AIC-7892A U160/m
1410-1413 : Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] System Controller
2000-2fff : PCI Bus #01
2000-20ff : PCI device 1002:4966 (ATI Technologies Inc)
3000-3fff : PCI Bus #02
3000-307f : 3Com Corporation 3c905C-TX/TX-M [Tornado]
3000-307f : 02:08.0
3080-309f : Creative Labs SB Live! EMU10k1
3080-309f : EMU10K1
30a0-30a7 : Creative Labs SB Live! MIDI/Game Port
30a8-30af : US Robotics/3Com 56K FaxModem Model 5610
30a8-30af : serial(auto)
f000-f00f : Advanced Micro Devices [AMD] AMD-768 [Opus] IDE
f000-f007 : ide0
f008-f00f : ide1
00000000-0009f3ff : System RAM
0009f400-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000cd000-000cd7ff : Extension ROM
000cd800-000d2bff : Extension ROM
000e0000-000effff : Extension ROM
000f0000-000fffff : System ROM
00100000-3feeffff : System RAM
00100000-002d2f8d : Kernel code
002d2f8e-00369c63 : Kernel data
3fef0000-3fefefff : ACPI Tables
3feff000-3fefffff : ACPI Non-volatile Storage
3ff00000-3ff7ffff : System RAM
3ff80000-3fffffff : reserved
ec000000-ec000fff : Adaptec AIC-7892A U160/m
ec000000-ec000fff : aic7xxx
ec100000-ec1fffff : PCI Bus #01
ec100000-ec10ffff : PCI device 1002:4966 (ATI Technologies Inc)
ec110000-ec11ffff : PCI device 1002:496e (ATI Technologies Inc)
ec200000-ec2fffff : PCI Bus #02
ec200000-ec200fff : Advanced Micro Devices [AMD] AMD-768 [Opus] USB
ec200000-ec200fff : usb-ohci
ec201000-ec20107f : 3Com Corporation 3c905C-TX/TX-M [Tornado]
ec500000-ec500fff : Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] System Controller
f0000000-f3ffffff : Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] System Controller
f4000000-fbffffff : PCI Bus #01
f4000000-f7ffffff : PCI device 1002:4966 (ATI Technologies Inc)
f8000000-fbffffff : PCI device 1002:496e (ATI Technologies Inc)
fec00000-fec03fff : reserved
fee00000-fee00fff : reserved
fff80000-ffffffff : reserved
[7.5.] PCI information ('lspci -vvv' as root)
00:00.0 Host bridge: Advanced Micro Devices [AMD]: Unknown device 700c (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at ec500000 (32-bit, prefetchable) [size=4K]
Region 2: I/O ports at 1410 [disabled] [size=4]
Capabilities: [a0] AGP version 2.0
Status: RQ=15 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Advanced Micro Devices [AMD]: Unknown device 700d (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 00002000-00002fff
Memory behind bridge: ec100000-ec1fffff
Prefetchable memory behind bridge: f4000000-fbffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:07.0 ISA bridge: Advanced Micro Devices [AMD]: Unknown device 7440 (rev 05)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Advanced Micro Devices [AMD]: Unknown device 7441 (rev 04) (prog-if 8a [Master SecP PriP])
Subsystem: Advanced Micro Devices [AMD]: Unknown device 7441
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at f000 [size=16]
00:07.3 Bridge: Advanced Micro Devices [AMD]: Unknown device 7443 (rev 03)
Subsystem: Advanced Micro Devices [AMD]: Unknown device 7443
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:09.0 SCSI storage controller: Adaptec 7892A (rev 02)
Subsystem: Adaptec: Unknown device e2a0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (10000ns min, 6250ns max), cache line size 10
Interrupt: pin A routed to IRQ 17
BIST result: 00
Region 0: I/O ports at 1000 [disabled] [size=256]
Region 1: Memory at ec000000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 PCI bridge: Advanced Micro Devices [AMD]: Unknown device 7448 (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=02, subordinate=02, sec-latency=168
I/O behind bridge: 00003000-00003fff
Memory behind bridge: ec200000-ec2fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
01:05.0 VGA compatible controller: ATI Technologies Inc: Unknown device 4966 (rev 01) (prog-if 00 [VGA])
Subsystem: Unknown device 174b:7176
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B+
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f4000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at 2000 [size=256]
Region 2: Memory at ec100000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=47 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA+ AGP- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:05.1 Display controller: ATI Technologies Inc: Unknown device 496e (rev 01)
Subsystem: Unknown device 174b:7177
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B+
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), cache line size 10
Region 0: Memory at f8000000 (32-bit, prefetchable) [disabled] [size=64M]
Region 1: Memory at ec110000 (32-bit, non-prefetchable) [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.0 USB Controller: Advanced Micro Devices [AMD]: Unknown device 7449 (rev 07) (prog-if 10 [OHCI])
Subsystem: Advanced Micro Devices [AMD]: Unknown device 7449
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin D routed to IRQ 19
Region 0: Memory at ec200000 (32-bit, non-prefetchable) [size=4K]
02:05.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07)
Subsystem: Creative Labs: Unknown device 8064
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 3080 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:05.1 Input device controller: Creative Labs SB Live! (rev 07)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 0: I/O ports at 30a0 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:07.0 Serial controller: US Robotics/3Com 56K FaxModem Model 5610 (rev 01) (prog-if 02 [16550])
Subsystem: US Robotics/3Com: Unknown device 00d3
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at 30a8 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0+,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
02:08.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev 78)
Subsystem: Tyan Computer: Unknown device 2466
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 80 (2500ns min, 2500ns max), cache line size 10
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at 3000 [size=128]
Region 1: Memory at ec201000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
[7.6.] SCSI information (from /proc/scsi/scsi)
Attached devices:
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: SEAGATE Model: ST336938LW Rev: 0003
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 02 Lun: 00
Vendor: SEAGATE Model: ST336938LW Rev: 0003
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: SONY Model: CD-RW CRX210E1 Rev: 2YS2
Type: CD-ROM ANSI SCSI revision: 02
[7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you
think to be relevant):
[X.] Other notes, patches, fixes, workarounds:
The configuration is largely the same as I'm using for 2.4.20
(imported via "make oldconfig") except no modules at all.
I note that processor 0 is reported as "AMD Athlon(tm) MP 2200+",
while the second is just "AMD Athlon(tm) Processor". Does that mean
the second one is *not* MP? I.e. did the dealer sell me the wrong
thing?
Thank you
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sat Mar 15 2003 - 22:00:44 EST