Hi
Similar issues here., though I must say the Adaptec driver hasn't worked for
me on all kernels I tried since my first try with 2.5.44. I get almost the
same output with a plain 2.5.65 kernel, though my kernel locks up just before
the crash you get, I get no dmesg output.
Note that it takes ages to get trough the SCSI driver towards the lockup. I
guess some timeouts cause this.
Config is the same, if it matters: SMP enabled.
Bus 0, device 6, function 0:
SCSI storage controller: Adaptec AIC-7880U (rev 0).
Attached are a CD-RW and a tapedrive.
2.4 kernels run fine.
Please let me know if additional details are required.
Jos
> Friday 21 March 2003 08:17, Zwane Mwaikambo wrote:
> Hi Justin i got this booting 2.5.65-mm2, 2.5.65 was fine there is an oops
> right at the end. Is there anything specific you want?
>
> 01:0d.0 SCSI storage controller: Adaptec AHA-294x / AIC-7870 (rev 03)
> 01:0e.0 SCSI storage controller: Adaptec AHA-294x / AIC-7870 (rev 03)
>
> There are 6 spindles on that second HBA, and a DLT and CDROM on the first.
>
> CONFIG_SCSI_AIC7XXX=y
> CONFIG_AIC7XXX_CMDS_PER_DEVICE=253
> CONFIG_AIC7XXX_RESET_DELAY_MS=15000
> # CONFIG_AIC7XXX_PROBE_EISA_VL is not set
> # CONFIG_AIC7XXX_BUILD_FIRMWARE is not set
> CONFIG_AIC7XXX_DEBUG_ENABLE=y
> CONFIG_AIC7XXX_DEBUG_MASK=0
> CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
> # CONFIG_SCSI_AIC7XXX_OLD is not set
>
> Starting NFS statd: [ OK ]
> Loading keymap: scsi1:0:0:0: Attempting to queue an ABORT message
>
> >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
>
> scsi1: Dumping Card State while idle, at SEQADDR 0x8
> Card was paused
> ACCUM = 0x55, SINDEX = 0xa, DINDEX = 0x8c, ARG_2 = 0x0
> HCNT = 0x0 SCBPTR = 0x8
> SCSISIGI[0xe6]:(REQI|BSYI|MSGI|IOI|CDI) ERROR[0x40]:(PCIERRSTAT)
> SCSIBUSL[0x80] LASTPHASE[0x1]:(P_BUSFREE)
> SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI)
> SBLKCTL[0x2]:(SELWIDE) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE)
> SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED)
> SSTAT0[0x25]:(DMADONE|SDONE|SELDI)
> SSTAT1[0xb]:(REQINIT|PHASECHG|BUSFREE) SSTAT2[0x0]
> SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO)
> SXFRCTL0[0x80]:(DFON) DFCNTRL[0x0]
> DFSTATUS[0x29]:(FIFOEMP|HDONE|FIFOQWDEMP)
> STACK: 0x0 0x169 0x10c 0x3
> SCB count = 56
> Kernel NEXTQSCB = 8
> Card NEXTQSCB = 8
> QINFIFO entries:
> Waiting Queue entries:
> Disconnected Queue entries: 0:13
> QOUTFIFO entries:
> Sequencer Free SCB List: 8 3 2 9 13 5 6 4 14 7 1 11 12 10 15
> Sequencer SCB Info:
> 0 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xd]
> 1 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 3 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 4 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 5 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 6 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 7 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 8 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 9 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 10 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 11 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 12 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 13 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 14 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 15 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> Pending list:
> 13 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
> Kernel Free SCB list: 10 11 0 25 41 28 31 40 45 29 30 46 47 24 26 5 20 21
> 42 43 27 23 22 49 50 36 37 3 48 4 1 7 18 44 35
> DevQ(0:0:0): 0 waiting
> DevQ(0:1:0): 0 waiting
> DevQ(0:2:0): 0 waiting
> DevQ(0:3:0): 0 waiting
> DevQ(0:4:0): 0 waiting
> DevQ(0:5:0): 0 waiting
>
> <<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
> (scsi1:A:0:0): Device is disconnected, re-queuing SCB
> Recovery code sleeping
> (scsi1:A:0:0): Abort Tag Message Sent
> (scsi1:A:0:0): SCB 13 - Abort Tag Completed.
> Recovery SCB completes
> Recovery code awake
> aic7xxx_abort returns 0x2002
> scsi1:0:0:0: Attempting to queue an ABORT message
> scsi1:0:0:0: Command not found
> aic7xxx_abort returns 0x2002
> scsi1:0:0:0: Attempting to queue an ABORT message
> scsi1:0:0:0: Command not found
> aic7xxx_abort returns 0x2002
> [ OK ]
> Loading system font: scsi1:0:0:0: Attempting to queue an ABORT message
> scsi1:0:0:0: Command not found
> aic7xxx_abort returns 0x2002
> scsi1:0:0:0: Attempting to queue an ABORT message
> scsi1:0:0:0: Command not found
> aic7xxx_abort returns 0x2002
> scsi1:0:0:0: Attempting to queue an ABORT message
> scsi1:0:0:0: Command not found
> aic7xxx_abort returns 0x2002
> scsi1:0:0:0: Attempting to queue a TARGET RESET message
> scsi1:0:0:0: Command not found
> aic7xxx_dev_reset returns 0x2002
> scsi1:0:0:0: Attempting to queue an ABORT message
> scsi1:0:0:0: Command not found
> aic7xxx_abort returns 0x2002
> scsi1:0:0:0: Attempting to queue an ABORT message
>
> >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
>
> scsi1: Dumping Card State while idle, at SEQADDR 0x8
> Card was paused
> ACCUM = 0xea, SINDEX = 0x64, DINDEX = 0x65, ARG_2 = 0xa
> HCNT = 0x0 SCBPTR = 0x4
> SCSISIGI[0x0] ERROR[0x40]:(PCIERRSTAT) SCSIBUSL[0x0]
> LASTPHASE[0x1]:(P_BUSFREE) SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI)
> SBLKCTL[0x2]:(SELWIDE) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE)
> SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED) SSTAT0[0x5]:(DMADONE|SDONE)
> SSTAT1[0xa]:(PHASECHG|BUSFREE) SSTAT2[0x0] SSTAT3[0x0]
> SIMODE0[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO)
> SXFRCTL0[0x80]:(DFON) DFCNTRL[0x0]
> DFSTATUS[0x2d]:(FIFOEMP|DFTHRESH|HDONE|FIFOQWDEMP)
> STACK: 0xe4 0x169 0x199 0x3
> SCB count = 56
> Kernel NEXTQSCB = 8
> Card NEXTQSCB = 8
> QINFIFO entries:
> Waiting Queue entries:
> Disconnected Queue entries: 4:43
> QOUTFIFO entries:
> Sequencer Free SCB List: 0 2 12 11 14 7 1 15 10 3 9 13 6 5 8
> Sequencer SCB Info:
> 0 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 1 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 3 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 4 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0x2b]
> 5 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 6 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 7 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 8 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 9 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 10 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 11 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 12 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 13 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 14 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 15 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> Pending list:
> 43 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
> Kernel Free SCB list: 31 44 46 30 40 45 29 3 24 23 37 47 20 21 5 42 27 26
> 50 22 49 36 1 4 48 18 11 10 7 0 25 28 41 13 35
> DevQ(0:0:0): 0 waiting
> DevQ(0:1:0): 0 waiting
> DevQ(0:2:0): 0 waiting
> DevQ(0:3:0): 0 waiting
> DevQ(0:4:0): 0 waiting
> DevQ(0:5:0): 0 waiting
>
> <<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
> (scsi1:A:0:0): Device is disconnected, re-queuing SCB
> (scsi1:A:0:0): Recovery code sleeping
> Abort Tag Message Sent
> Recovery code awake
> Timer Expired
> aic7xxx_abort returns 0x2003
> SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 6000000
> end_request: I/O error, dev sda, sector 133984
> Buffer I/O error on device sd(8,1), logical block 16744
> SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 6000000
> end_request: I/O error, dev sda, sector 4980800
> Buffer I/O error on device sd(8,1), logical block 622596
> Debug: sleeping function called from illegal context at
> include/linux/rwsem.h:43
> Call Trace:
> [<c011ed18>] __might_sleep+0x58/0x60
> [<c028ec00>] __bdevname+0x50/0xc0
> [<c015cb41>] buffer_io_error+0x11/0x30
> [<c015d406>] end_buffer_async_write+0x166/0x190
> [<c0160101>] end_bio_bh_io_sync+0x21/0x30
> [<c0161515>] bio_endio+0x35/0x60
> [<c028df8f>] __end_that_request_first+0x1ff/0x220
> [<c028dfc7>] end_that_request_first+0x17/0x20
> [<c028a864>] elv_next_request+0x84/0xe0
> [<c02e187f>] scsi_request_fn+0x3f/0x2a0
> [<c028c442>] __blk_run_queue+0x12/0x20
> [<c02e022d>] scsi_restart_operations+0xbd/0x120
> [<c02e05b8>] scsi_error_handler+0x138/0x1a0
> [<c02e0480>] scsi_error_handler+0x0/0x1a0
> [<c0107095>] kernel_thread_helper+0x5/0x10
> Buffer I/O error on device sd(8,1), logical block 557066
> (scsi1:A:0:0): SCB 43 - Abort Tag Completed.
> Recovery SCB completes
>
> Unable to handle kernel paging request at virtual address 6b6b6b6b
> printing eip:
> 6b6b6b6b
> *pde = 00000000
> Oops: 0000 [#1]
> CPU: 1
> EIP: 0060:[<6b6b6b6b>] Not tainted
> EFLAGS: 00010002 VLI
> EIP is at 0x6b6b6b6b
> eax: cbb1ccf8 ebx: 00000000 ecx: cbe31290 edx: 00000000
> esi: 00000001 edi: c1509f20 ebp: 00000005 esp: c1509ea0
> ds: 007b es: 007b ss: 0068
> Process swapper (pid: 0, threadinfo=c1508000 task=c150a660)
> Stack: c02ff78c cbb1ccf8 cbb1ccf8 cbe31290 c0305c07 cbe31290 cbb1ccf8
> 00000292 3e7ac717 c17e848c cbffe4f4 04000001 c010bb0d 00000005 cbe31290
> c1509f20 c05060a0 c1508000 c1508000 00000005 c010be49 00000005 c1509f20
> cbffe4f4 Call Trace:
> [<c02ff78c>] ahc_linux_run_complete_queue+0x3c/0x50
> [<c0305c07>] ahc_linux_isr+0x1d7/0x3a0
> [<c010bb0d>] handle_IRQ_event+0x2d/0x50
> [<c010be49>] do_IRQ+0x109/0x210
> [<c010a398>] common_interrupt+0x18/0x20
> [<c01264f6>] do_softirq+0x56/0xc0
> [<c01168a5>] smp_apic_timer_interrupt+0xf5/0x160
> [<c0106ea0>] default_idle+0x0/0x40
> [<c010a41a>] apic_timer_interrupt+0x1a/0x20
> [<c0106ea0>] default_idle+0x0/0x40
> [<c0106ece>] default_idle+0x2e/0x40
> [<c0106f5a>] cpu_idle+0x3a/0x50
> [<c01226fd>] release_console_sem+0xbd/0x170
> [<c012256b>] printk+0x1eb/0x270
>
> Code: Bad EIP value.
> <0>Kernel panic: Aiee, killing interrupt handler!
> In interrupt handler - not syncing
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sun Mar 23 2003 - 22:00:35 EST