On Mon, Apr 21, 2003 at 03:47:32PM -0300, Marcelo Tosatti wrote:
>
> Here goes the first candidate for 2.4.21.
>
> Please test it extensively.
I'm still seeing a problem with my primary IDE channel locking up for
10-15s at a time, an event I can trigger by running updatedb (i.e. the
database update for 'locate').
Original report was against 2.4.21-pre7. I've tried 2.4.21-pre5-ac3
with the same problem, 2.4.21-pre4 does NOT exhibit the problem.
The problem manifests itself in dmesg as:
Apr 23 15:27:22 emelia kernel: hda: dma_timer_expiry: dma status == 0x24
Apr 23 15:27:22 emelia kernel: hda: lost interrupt
Apr 23 15:27:22 emelia kernel: hda: dma_intr: bad DMA status (dma_stat=30)
Apr 23 15:27:22 emelia kernel: hda: dma_intr: status=0x50 { DriveReady SeekComplete }
In normal use this problem will manifest at 'random', but frequently
enough to make the machine unuseable for any great amount of HD
activity.
The affected machine is based on a Gigabyte GA-7VTX-H motherboard, with
BIOS revision F8a. That's an all-VIA KT266 chipset, as seen in the lspci
output below. Athlon XP 1600+ CPU @1.4GHz (i.e. not overclocked). 512MB
PC2100 DDR RAM. The only card is a PNY GF4Ti4800 128MB (unrecognised
in lspci output, but it's just an 8x AGP version of the 4600 model that
is recognised, as far as I know). Sound and LAN are onboard.
The affected Hard Disk is a Maxtor 60GB, as master on primary IDE channel,
no slave, using an 80wire cable. Secondary IDE channel has a 4x CD-ROM
as master, and CD-RW as slave on a 40wire cable. The two channels are
using seperate IRQ and memory ranges (see dmesg output in section 7.7).
hdparm -i /dev/hda
/dev/hda:
Model=MAXTOR 4K060H3, FwRev=A08.1500, SerialNo=673200978766
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=32256, SectSize=21298, ECCbytes=4
BuffType=DualPortCache, BuffSize=2000kB, MaxMultSect=16, MultSect=off
CurCHS=34404/15/32, CurSects=16513920, LBA=yes, LBAsects=117266688
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5
That's as it is configured post-boot, no hdparm command run to change
anything. I do have to force the CHS to 14370,255,32 so that the BIOS,
Windows 98 and Linux are all happy.
Information for how it just occurred with 2.4.21-rc1:
/proc/version:
Linux version 2.4.21-rc1 (athan@emelia) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 Mon Apr 21 21:07:22 BST 2003
ver_linux:
/root/bin/getinfo: /usr/local/src/kernels/2.4.21-rc1/scripts/ver_linux: No such file or directory
/proc/cpuinfo:
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 6
model name : AMD Athlon(tm) XP 1600+
stepping : 2
cpu MHz : 1406.013
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
bogomips : 2804.94
/proc/modules:
mousedev 3904 0 (unused)
hid 19520 0 (unused)
usb-uhci 21636 0 (unused)
ide-scsi 9120 0
scsi_mod 89880 1 [ide-scsi]
ide-cd 29024 0
cdrom 29024 0 [ide-cd]
8139too 15360 1
mii 2448 0 [8139too]
/proc/ioports:
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial(set)
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(set)
0cf8-0cff : PCI conf1
dc00-dcff : Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
dc00-dcff : 8139too
e000-e01f : VIA Technologies, Inc. USB (#3)
e000-e01f : usb-uhci
e400-e41f : VIA Technologies, Inc. USB (#2)
e400-e41f : usb-uhci
e800-e81f : VIA Technologies, Inc. USB
e800-e81f : usb-uhci
ec00-ec3f : Ensoniq 5880 AudioPCI
fc00-fc0f : VIA Technologies, Inc. VT82C586B PIPC Bus Master IDE
fc00-fc07 : ide0
fc08-fc0f : ide1
/proc/iomem:
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000f0000-000fffff : System ROM
00100000-1ffeffff : System RAM
00100000-00265824 : Kernel code
00265825-002f987f : Kernel data
1fff0000-1fff7fff : ACPI Tables
1fff8000-1fffffff : ACPI Non-volatile Storage
cdc00000-ddcfffff : PCI Bus #01
d0000000-d7ffffff : PCI device 10de:0280 (nVidia Corporation)
dde00000-dfefffff : PCI Bus #01
de000000-deffffff : PCI device 10de:0280 (nVidia Corporation)
dfffff00-dfffffff : Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
dfffff00-dfffffff : 8139too
e0000000-e7ffffff : VIA Technologies, Inc. VT8367 [KT266]
fec00000-fec00fff : reserved
fee00000-fee00fff : reserved
fffc0000-ffffffff : reserved
lspci -vvv:
00:00.0 Host bridge: VIA Technologies, Inc. VT8367 [KT266]
Subsystem: VIA Technologies, Inc. VT8367 [KT266]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8367 [KT266 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: dde00000-dfefffff
Prefetchable memory behind bridge: cdc00000-ddcfffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 04)
Subsystem: Giga-byte Technology: Unknown device a000
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (3000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at ec00 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
Subsystem: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at fc00 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at e800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at e400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.4 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at e000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:13.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at dc00 [size=256]
Region 1: Memory at dfffff00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: nVidia Corporation: Unknown device 0280 (rev a1) (prog-if 00 [VGA])
Subsystem: Micro-star International Co Ltd: Unknown device 9000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at dfee0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
/proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: MITSUMI Model: CR-4804TE Rev: 3.0D
Type: CD-ROM ANSI SCSI revision: 02
post-boot dmesg:
Linux version 2.4.21-rc1 (athan@emelia) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 Mon Apr 21 21:07:22 BST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000fb9b0
hm, page 000fb000 reserved twice.
hm, page 000fc000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: GIGABYTE Product ID: 7VTXH APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 2 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Kernel command line: BOOT_IMAGE=2421r1 ro root=305 mem=nopentium hda=14370,255,32 hdd=ide-scsi
ide_setup: hda=14370,255,32
ide_setup: hdd=ide-scsi
Initializing CPU#0
Detected 1406.013 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2804.94 BogoMIPS
Memory: 515248k/524224k available (1430k kernel code, 8588k reserved, 592k data, 116k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbf7 c1cbfbff 00000000 00000000
CPU: Common caps: 0383fbf7 c1cbfbff 00000000 00000000
CPU: AMD Athlon(tm) XP 1600+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000080
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-11, 2-12, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 19.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178002
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0002
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 001 01 0 0 0 0 0 1 1 51
07 001 01 0 0 0 0 0 1 1 59
08 001 01 0 0 0 0 0 1 1 61
09 001 01 0 0 0 0 0 1 1 69
0a 001 01 1 1 0 1 0 1 1 71
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 001 01 0 0 0 0 0 1 1 79
0e 001 01 0 0 0 0 0 1 1 81
0f 001 01 0 0 0 0 0 1 1 89
10 001 01 1 1 0 1 0 1 1 91
11 001 01 1 1 0 1 0 1 1 99
12 001 01 1 1 0 1 0 1 1 A1
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1405.9966 MHz.
..... host bus clock speed is 267.8089 MHz.
cpu: 0, clocks: 2678089, slice: 1339044
CPU0<T0:2678080,T1:1339024,D:12,S:1339044,C:2678089>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfdb01, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router default [1106/3074] at 00:11.0
PCI->APIC IRQ transform: (B0,I16,P0) -> 17
PCI->APIC IRQ transform: (B0,I17,P0) -> 16
PCI->APIC IRQ transform: (B0,I17,P3) -> 10
PCI->APIC IRQ transform: (B0,I17,P3) -> 10
PCI->APIC IRQ transform: (B0,I17,P3) -> 10
PCI->APIC IRQ transform: (B0,I19,P0) -> 18
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
Journalled Block Device driver loaded
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
Non-volatile memory driver v1.2
Software Watchdog Timer: 0.05, timer margin: 60 sec
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT266 chipset
agpgart: AGP aperture is 128M @ 0xe0000000
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci00:11.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:DMA
hda: MAXTOR 4K060H3, ATA DISK drive
blk: queue c0346a60, I/O limit 4095Mb (mask 0xffffffff)
hdc: TOSHIBA CD-ROM XM-5302TA, ATAPI CD/DVD-ROM drive
hdd: CR-4804TE, ATAPI CD/DVD-ROM drive
hdc: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hdc: set_drive_speed_status: error=0x04
ide1: Drive 0 didn't accept speed setting. Oh, well.
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 117266688 sectors (60041 MB) w/2000KiB Cache, CHS=14370/255/32, UDMA(100)
Partition check:
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 >
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
I2O Core - (C) Copyright 1999 Red Hat Software
I2O: Event thread created as pid 8
Linux I2O PCI support (c) 1999 Red Hat Software.
i2o: Checking for PCI I2O controllers...
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 292 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
ip6_tables: (C) 2000-2002 Netfilter core team
registering ipv6 mark target
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 116k freed
Adding Swap: 265176k swap-space (priority -1)
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xe0880f00, 00:20:ed:1d:fe:2a, IRQ 18
eth0: Identified 8139 chip type 'RTL-8139B'
hdc: attached ide-cdrom driver.
hdc: ATAPI 4X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
SCSI subsystem driver Revision: 1.00
hdd: attached ide-scsi driver.
hdd: DMA disabled
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: MITSUMI Model: CR-4804TE Rev: 3.0D
Type: CD-ROM ANSI SCSI revision: 02
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,9), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,10), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,11), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 41e1.
Relevant lines of /var/log/kern.log:
Apr 23 15:22:16 emelia kernel: klogd 1.4.1#10, log source = /proc/kmsg started.
Apr 23 15:22:16 emelia kernel: Inspecting /boot/System.map-2.4.21-rc1
Apr 23 15:22:16 emelia kernel: Loaded 19134 symbols from /boot/System.map-2.4.21-rc1.
Apr 23 15:22:16 emelia kernel: Symbols match kernel version 2.4.21.
Apr 23 15:22:16 emelia kernel: Loaded 119 symbols from 6 modules.
Apr 23 15:22:16 emelia kernel: Linux version 2.4.21-rc1 (athan@emelia) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 Mon Apr 21 21:07:22 BST 2003
Apr 23 15:22:16 emelia kernel: BIOS-provided physical RAM map:
Apr 23 15:22:16 emelia kernel: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
Apr 23 15:22:16 emelia kernel: BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
Apr 23 15:22:16 emelia kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Apr 23 15:22:16 emelia kernel: BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
Apr 23 15:22:16 emelia kernel: BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
Apr 23 15:22:16 emelia kernel: BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
Apr 23 15:22:16 emelia kernel: BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
Apr 23 15:22:16 emelia kernel: BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
Apr 23 15:22:16 emelia kernel: BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
Apr 23 15:22:16 emelia kernel: 511MB LOWMEM available.
Apr 23 15:22:16 emelia kernel: found SMP MP-table at 000fb9b0
Apr 23 15:22:16 emelia kernel: hm, page 000fb000 reserved twice.
Apr 23 15:22:16 emelia kernel: hm, page 000fc000 reserved twice.
Apr 23 15:22:16 emelia kernel: hm, page 000f6000 reserved twice.
Apr 23 15:22:16 emelia kernel: hm, page 000f7000 reserved twice.
Apr 23 15:22:16 emelia kernel: On node 0 totalpages: 131056
Apr 23 15:22:16 emelia kernel: zone(0): 4096 pages.
Apr 23 15:22:16 emelia kernel: zone(1): 126960 pages.
Apr 23 15:22:16 emelia kernel: zone(2): 0 pages.
Apr 23 15:22:16 emelia kernel: Intel MultiProcessor Specification v1.4
Apr 23 15:22:16 emelia kernel: Virtual Wire compatibility mode.
Apr 23 15:22:16 emelia kernel: OEM ID: GIGABYTE Product ID: 7VTXH APIC at: 0xFEE00000
Apr 23 15:22:16 emelia kernel: Processor #0 Pentium(tm) Pro APIC version 17
Apr 23 15:22:16 emelia kernel: I/O APIC #2 Version 2 at 0xFEC00000.
Apr 23 15:22:16 emelia kernel: Enabling APIC mode: Flat.^IUsing 1 I/O APICs
Apr 23 15:22:16 emelia kernel: Processors: 1
Apr 23 15:22:16 emelia kernel: Kernel command line: BOOT_IMAGE=2421r1 ro root=305 mem=nopentium hda=14370,255,32 hdd=ide-scsi
Apr 23 15:22:16 emelia kernel: ide_setup: hda=14370,255,32
Apr 23 15:22:16 emelia kernel: ide_setup: hdd=ide-scsi
Apr 23 15:22:16 emelia kernel: Initializing CPU#0
Apr 23 15:22:16 emelia kernel: Detected 1406.013 MHz processor.
Apr 23 15:22:16 emelia kernel: Console: colour VGA+ 80x25
Apr 23 15:22:16 emelia kernel: Calibrating delay loop... 2804.94 BogoMIPS
Apr 23 15:22:16 emelia kernel: Memory: 515248k/524224k available (1430k kernel code, 8588k reserved, 592k data, 116k init, 0k highmem)
Apr 23 15:22:16 emelia kernel: Checking if this processor honours the WP bit even in supervisor mode... Ok.
Apr 23 15:22:16 emelia kernel: Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Apr 23 15:22:16 emelia kernel: Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Apr 23 15:22:16 emelia kernel: Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Apr 23 15:22:16 emelia kernel: Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Apr 23 15:22:16 emelia kernel: Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
Apr 23 15:22:16 emelia kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
Apr 23 15:22:16 emelia kernel: CPU: L2 Cache: 256K (64 bytes/line)
Apr 23 15:22:16 emelia kernel: Intel machine check architecture supported.
Apr 23 15:22:16 emelia kernel: Intel machine check reporting enabled on CPU#0.
Apr 23 15:22:16 emelia kernel: CPU: After generic, caps: 0383fbf7 c1cbfbff 00000000 00000000
Apr 23 15:22:16 emelia kernel: CPU: Common caps: 0383fbf7 c1cbfbff 00000000 00000000
Apr 23 15:22:16 emelia kernel: CPU: AMD Athlon(tm) XP 1600+ stepping 02
Apr 23 15:22:16 emelia kernel: Enabling fast FPU save and restore... done.
Apr 23 15:22:16 emelia kernel: Enabling unmasked SIMD FPU exception support... done.
Apr 23 15:22:16 emelia kernel: Checking 'hlt' instruction... OK.
Apr 23 15:22:16 emelia kernel: POSIX conformance testing by UNIFIX
Apr 23 15:22:16 emelia kernel: enabled ExtINT on CPU#0
Apr 23 15:22:16 emelia kernel: ESR value before enabling vector: 00000080
Apr 23 15:22:16 emelia kernel: ESR value after enabling vector: 00000000
Apr 23 15:22:16 emelia kernel: ENABLING IO-APIC IRQs
Apr 23 15:22:16 emelia kernel: Setting 2 in the phys_id_present_map
Apr 23 15:22:16 emelia kernel: ...changing IO-APIC physical APIC ID to 2 ... ok.
Apr 23 15:22:16 emelia kernel: init IO_APIC IRQs
Apr 23 15:22:16 emelia kernel: IO-APIC (apicid-pin) 2-0, 2-5, 2-11, 2-12, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
Apr 23 15:22:16 emelia kernel: ..TIMER: vector=0x31 pin1=2 pin2=0
Apr 23 15:22:16 emelia kernel: number of MP IRQ sources: 19.
Apr 23 15:22:16 emelia kernel: number of IO-APIC #2 registers: 24.
Apr 23 15:22:16 emelia kernel: testing the IO APIC.......................
Apr 23 15:22:16 emelia kernel:
Apr 23 15:22:16 emelia kernel: IO APIC #2......
Apr 23 15:22:16 emelia kernel: .... register #00: 02000000
Apr 23 15:22:16 emelia kernel: ....... : physical APIC id: 02
Apr 23 15:22:16 emelia kernel: ....... : Delivery Type: 0
Apr 23 15:22:16 emelia kernel: ....... : LTS : 0
Apr 23 15:22:16 emelia kernel: .... register #01: 00178002
Apr 23 15:22:16 emelia kernel: ....... : max redirection entries: 0017
Apr 23 15:22:16 emelia kernel: ....... : PRQ implemented: 1
Apr 23 15:22:16 emelia kernel: ....... : IO APIC version: 0002
Apr 23 15:22:16 emelia kernel: .... IRQ redirection table:
Apr 23 15:22:16 emelia kernel: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
Apr 23 15:22:16 emelia kernel: 00 000 00 1 0 0 0 0 0 0 00
Apr 23 15:22:16 emelia kernel: 01 001 01 0 0 0 0 0 1 1 39
Apr 23 15:22:16 emelia kernel: 02 001 01 0 0 0 0 0 1 1 31
Apr 23 15:22:16 emelia kernel: 03 001 01 0 0 0 0 0 1 1 41
Apr 23 15:22:16 emelia kernel: 04 001 01 0 0 0 0 0 1 1 49
Apr 23 15:22:16 emelia kernel: 05 000 00 1 0 0 0 0 0 0 00
Apr 23 15:22:16 emelia kernel: 06 001 01 0 0 0 0 0 1 1 51
Apr 23 15:22:16 emelia kernel: 07 001 01 0 0 0 0 0 1 1 59
Apr 23 15:22:16 emelia kernel: 08 001 01 0 0 0 0 0 1 1 61
Apr 23 15:22:16 emelia kernel: 09 001 01 0 0 0 0 0 1 1 69
Apr 23 15:22:16 emelia kernel: 0a 001 01 1 1 0 1 0 1 1 71
Apr 23 15:22:16 emelia kernel: 0b 000 00 1 0 0 0 0 0 0 00
Apr 23 15:22:16 emelia kernel: 0c 000 00 1 0 0 0 0 0 0 00
Apr 23 15:22:16 emelia kernel: 0d 001 01 0 0 0 0 0 1 1 79
Apr 23 15:22:16 emelia kernel: 0e 001 01 0 0 0 0 0 1 1 81
Apr 23 15:22:16 emelia kernel: 0f 001 01 0 0 0 0 0 1 1 89
Apr 23 15:22:16 emelia kernel: 10 001 01 1 1 0 1 0 1 1 91
Apr 23 15:22:16 emelia kernel: 11 001 01 1 1 0 1 0 1 1 99
Apr 23 15:22:16 emelia kernel: 12 001 01 1 1 0 1 0 1 1 A1
Apr 23 15:22:16 emelia kernel: 13 000 00 1 0 0 0 0 0 0 00
Apr 23 15:22:16 emelia kernel: 14 000 00 1 0 0 0 0 0 0 00
Apr 23 15:22:16 emelia kernel: 15 000 00 1 0 0 0 0 0 0 00
Apr 23 15:22:16 emelia kernel: 16 000 00 1 0 0 0 0 0 0 00
Apr 23 15:22:16 emelia kernel: 17 000 00 1 0 0 0 0 0 0 00
Apr 23 15:22:16 emelia kernel: IRQ to pin mappings:
Apr 23 15:22:16 emelia kernel: IRQ0 -> 0:2
Apr 23 15:22:16 emelia kernel: IRQ1 -> 0:1
Apr 23 15:22:16 emelia kernel: IRQ3 -> 0:3
Apr 23 15:22:16 emelia kernel: IRQ4 -> 0:4
Apr 23 15:22:16 emelia kernel: IRQ6 -> 0:6
Apr 23 15:22:16 emelia kernel: IRQ7 -> 0:7
Apr 23 15:22:16 emelia kernel: IRQ8 -> 0:8
Apr 23 15:22:16 emelia kernel: IRQ9 -> 0:9
Apr 23 15:22:16 emelia kernel: IRQ10 -> 0:10
Apr 23 15:22:16 emelia kernel: IRQ13 -> 0:13
Apr 23 15:22:16 emelia kernel: IRQ14 -> 0:14
Apr 23 15:22:16 emelia kernel: IRQ15 -> 0:15
Apr 23 15:22:16 emelia kernel: IRQ16 -> 0:16
Apr 23 15:22:16 emelia kernel: IRQ17 -> 0:17
Apr 23 15:22:16 emelia kernel: IRQ18 -> 0:18
Apr 23 15:22:16 emelia kernel: .................................... done.
Apr 23 15:22:16 emelia kernel: Using local APIC timer interrupts.
Apr 23 15:22:16 emelia kernel: calibrating APIC timer ...
Apr 23 15:22:16 emelia kernel: ..... CPU clock speed is 1405.9966 MHz.
Apr 23 15:22:16 emelia kernel: ..... host bus clock speed is 267.8089 MHz.
Apr 23 15:22:16 emelia kernel: cpu: 0, clocks: 2678089, slice: 1339044
Apr 23 15:22:16 emelia kernel: CPU0<T0:2678080,T1:1339024,D:12,S:1339044,C:2678089>
Apr 23 15:22:16 emelia kernel: mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
Apr 23 15:22:16 emelia kernel: mtrr: detected mtrr type: Intel
Apr 23 15:22:16 emelia kernel: PCI: PCI BIOS revision 2.10 entry at 0xfdb01, last bus=1
Apr 23 15:22:16 emelia kernel: PCI: Using configuration type 1
Apr 23 15:22:16 emelia kernel: PCI: Probing PCI hardware
Apr 23 15:22:16 emelia kernel: PCI: Using IRQ router default [1106/3074] at 00:11.0
Apr 23 15:22:16 emelia kernel: PCI->APIC IRQ transform: (B0,I16,P0) -> 17
Apr 23 15:22:16 emelia kernel: PCI->APIC IRQ transform: (B0,I17,P0) -> 16
Apr 23 15:22:16 emelia kernel: PCI->APIC IRQ transform: (B0,I17,P3) -> 10
Apr 23 15:22:16 emelia last message repeated 2 times
Apr 23 15:22:16 emelia kernel: PCI->APIC IRQ transform: (B0,I19,P0) -> 18
Apr 23 15:22:16 emelia kernel: PCI->APIC IRQ transform: (B1,I0,P0) -> 16
Apr 23 15:22:16 emelia kernel: isapnp: Scanning for PnP cards...
Apr 23 15:22:16 emelia kernel: isapnp: No Plug & Play device found
Apr 23 15:22:16 emelia kernel: Linux NET4.0 for Linux 2.4
Apr 23 15:22:16 emelia kernel: Based upon Swansea University Computer Society NET3.039
Apr 23 15:22:16 emelia kernel: Initializing RT netlink socket
Apr 23 15:22:16 emelia kernel: Starting kswapd
Apr 23 15:22:16 emelia kernel: VFS: Diskquotas version dquot_6.4.0 initialized
Apr 23 15:22:16 emelia kernel: Journalled Block Device driver loaded
Apr 23 15:22:16 emelia kernel: Detected PS/2 Mouse Port.
Apr 23 15:22:16 emelia kernel: pty: 256 Unix98 ptys configured
Apr 23 15:22:16 emelia kernel: Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
Apr 23 15:22:16 emelia kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
Apr 23 15:22:16 emelia kernel: ttyS01 at 0x02f8 (irq = 3) is a 16550A
Apr 23 15:22:16 emelia kernel: Real Time Clock Driver v1.10e
Apr 23 15:22:16 emelia kernel: Non-volatile memory driver v1.2
Apr 23 15:22:16 emelia kernel: Software Watchdog Timer: 0.05, timer margin: 60 sec
Apr 23 15:22:16 emelia kernel: Floppy drive(s): fd0 is 1.44M
Apr 23 15:22:16 emelia kernel: FDC 0 is a post-1991 82077
Apr 23 15:22:16 emelia kernel: Linux agpgart interface v0.99 (c) Jeff Hartmann
Apr 23 15:22:16 emelia kernel: agpgart: Maximum main memory to use for agp memory: 439M
Apr 23 15:22:16 emelia kernel: agpgart: Detected Via Apollo Pro KT266 chipset
Apr 23 15:22:16 emelia kernel: agpgart: AGP aperture is 128M @ 0xe0000000
Apr 23 15:22:16 emelia kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
Apr 23 15:22:16 emelia kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Apr 23 15:22:16 emelia kernel: VP_IDE: IDE controller at PCI slot 00:11.1
Apr 23 15:22:16 emelia kernel: VP_IDE: chipset revision 6
Apr 23 15:22:16 emelia kernel: VP_IDE: not 100%% native mode: will probe irqs later
Apr 23 15:22:16 emelia kernel: VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci00:11.1
Apr 23 15:22:16 emelia kernel: ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
Apr 23 15:22:16 emelia kernel: ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:DMA
Apr 23 15:22:16 emelia kernel: hda: MAXTOR 4K060H3, ATA DISK drive
Apr 23 15:22:16 emelia kernel: blk: queue c0346a60, I/O limit 4095Mb (mask 0xffffffff)
Apr 23 15:22:16 emelia kernel: hdc: TOSHIBA CD-ROM XM-5302TA, ATAPI CD/DVD-ROM drive
Apr 23 15:22:16 emelia kernel: hdd: CR-4804TE, ATAPI CD/DVD-ROM drive
Apr 23 15:22:16 emelia kernel: hdc: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
Apr 23 15:22:16 emelia kernel: hdc: set_drive_speed_status: error=0x04
Apr 23 15:22:16 emelia kernel: ide1: Drive 0 didn't accept speed setting. Oh, well.
Apr 23 15:22:16 emelia kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Apr 23 15:22:16 emelia kernel: ide1 at 0x170-0x177,0x376 on irq 15
Apr 23 15:22:16 emelia kernel: hda: attached ide-disk driver.
Apr 23 15:22:16 emelia kernel: hda: host protected area => 1
Apr 23 15:22:16 emelia kernel: hda: 117266688 sectors (60041 MB) w/2000KiB Cache, CHS=14370/255/32, UDMA(100)
Apr 23 15:22:16 emelia kernel: Partition check:
Apr 23 15:22:16 emelia kernel: hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 >
Apr 23 15:22:16 emelia kernel: usb.c: registered new driver usbdevfs
Apr 23 15:22:16 emelia kernel: usb.c: registered new driver hub
Apr 23 15:22:16 emelia kernel: I2O Core - (C) Copyright 1999 Red Hat Software
Apr 23 15:22:16 emelia kernel: I2O: Event thread created as pid 8
Apr 23 15:22:16 emelia kernel: Linux I2O PCI support (c) 1999 Red Hat Software.
Apr 23 15:22:16 emelia kernel: i2o: Checking for PCI I2O controllers...
Apr 23 15:22:16 emelia kernel: I2O configuration manager v 0.04.
Apr 23 15:22:16 emelia kernel: (C) Copyright 1999 Red Hat Software
Apr 23 15:22:16 emelia kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Apr 23 15:22:16 emelia kernel: IP Protocols: ICMP, UDP, TCP
Apr 23 15:22:16 emelia kernel: IP: routing cache hash table of 4096 buckets, 32Kbytes
Apr 23 15:22:16 emelia kernel: TCP: Hash tables configured (established 32768 bind 32768)
Apr 23 15:22:16 emelia kernel: IPv4 over IPv4 tunneling driver
Apr 23 15:22:16 emelia kernel: GRE over IPv4 tunneling driver
Apr 23 15:22:16 emelia kernel: ip_conntrack version 2.1 (4095 buckets, 32760 max) - 292 bytes per conntrack
Apr 23 15:22:16 emelia kernel: ip_tables: (C) 2000-2002 Netfilter core team
Apr 23 15:22:16 emelia kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Apr 23 15:22:16 emelia kernel: IPv6 v0.8 for NET4.0
Apr 23 15:22:16 emelia kernel: IPv6 over IPv4 tunneling driver
Apr 23 15:22:16 emelia kernel: ip6_tables: (C) 2000-2002 Netfilter core team
Apr 23 15:22:16 emelia kernel: registering ipv6 mark target
Apr 23 15:22:16 emelia kernel: VFS: Mounted root (ext2 filesystem) readonly.
Apr 23 15:22:16 emelia kernel: Freeing unused kernel memory: 116k freed
Apr 23 15:22:16 emelia kernel: Adding Swap: 265176k swap-space (priority -1)
Apr 23 15:22:16 emelia kernel: 8139too Fast Ethernet driver 0.9.26
Apr 23 15:22:16 emelia kernel: eth0: RealTek RTL8139 Fast Ethernet at 0xe0880f00, 00:20:ed:1d:fe:2a, IRQ 18
Apr 23 15:22:16 emelia kernel: eth0: Identified 8139 chip type 'RTL-8139B'
Apr 23 15:22:16 emelia kernel: hdc: attached ide-cdrom driver.
Apr 23 15:22:16 emelia kernel: hdc: ATAPI 4X CD-ROM drive, 128kB Cache
Apr 23 15:22:16 emelia kernel: Uniform CD-ROM driver Revision: 3.12
Apr 23 15:22:16 emelia kernel: SCSI subsystem driver Revision: 1.00
Apr 23 15:22:16 emelia kernel: hdd: attached ide-scsi driver.
Apr 23 15:22:16 emelia kernel: hdd: DMA disabled
Apr 23 15:22:16 emelia kernel: scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Apr 23 15:22:16 emelia kernel: Vendor: MITSUMI Model: CR-4804TE Rev: 3.0D
Apr 23 15:22:16 emelia kernel: Type: CD-ROM ANSI SCSI revision: 02
Apr 23 15:22:16 emelia kernel: kjournald starting. Commit interval 5 seconds
Apr 23 15:22:16 emelia kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,7), internal journal
Apr 23 15:22:16 emelia kernel: EXT3-fs: mounted filesystem with ordered data mode.
Apr 23 15:22:16 emelia kernel: kjournald starting. Commit interval 5 seconds
Apr 23 15:22:16 emelia kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,9), internal journal
Apr 23 15:22:16 emelia kernel: EXT3-fs: mounted filesystem with ordered data mode.
Apr 23 15:22:16 emelia kernel: kjournald starting. Commit interval 5 seconds
Apr 23 15:22:16 emelia kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,10), internal journal
Apr 23 15:22:16 emelia kernel: EXT3-fs: mounted filesystem with ordered data mode.
Apr 23 15:22:16 emelia kernel: kjournald starting. Commit interval 5 seconds
Apr 23 15:22:16 emelia kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,11), internal journal
Apr 23 15:22:16 emelia kernel: EXT3-fs: mounted filesystem with ordered data mode.
Apr 23 15:22:16 emelia kernel: eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 41e1.
Apr 23 15:22:20 emelia kernel: usb-uhci.c: $Revision: 1.275 $ time 21:12:34 Apr 21 2003
Apr 23 15:22:20 emelia kernel: usb-uhci.c: High bandwidth mode enabled
Apr 23 15:22:20 emelia kernel: usb-uhci.c: USB UHCI at I/O 0xe800, IRQ 10
Apr 23 15:22:20 emelia kernel: usb-uhci.c: Detected 2 ports
Apr 23 15:22:20 emelia kernel: usb.c: new USB bus registered, assigned bus number 1
Apr 23 15:22:20 emelia kernel: hub.c: USB hub found
Apr 23 15:22:20 emelia kernel: hub.c: 2 ports detected
Apr 23 15:22:20 emelia kernel: usb-uhci.c: USB UHCI at I/O 0xe400, IRQ 10
Apr 23 15:22:20 emelia kernel: usb-uhci.c: Detected 2 ports
Apr 23 15:22:20 emelia kernel: usb.c: new USB bus registered, assigned bus number 2
Apr 23 15:22:20 emelia kernel: hub.c: USB hub found
Apr 23 15:22:20 emelia kernel: hub.c: 2 ports detected
Apr 23 15:22:20 emelia kernel: usb-uhci.c: USB UHCI at I/O 0xe000, IRQ 10
Apr 23 15:22:20 emelia kernel: usb-uhci.c: Detected 2 ports
Apr 23 15:22:20 emelia kernel: usb.c: new USB bus registered, assigned bus number 3
Apr 23 15:22:20 emelia kernel: hub.c: USB hub found
Apr 23 15:22:20 emelia kernel: hub.c: 2 ports detected
Apr 23 15:22:20 emelia kernel: usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Apr 23 15:22:21 emelia kernel: usb.c: registered new driver hiddev
Apr 23 15:22:21 emelia kernel: usb.c: registered new driver hid
Apr 23 15:22:21 emelia kernel: hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
Apr 23 15:22:21 emelia kernel: hid-core.c: USB HID support drivers
Apr 23 15:22:21 emelia kernel: mice: PS/2 mouse device common for all mice
Apr 23 15:22:21 emelia kernel: hub.c: new USB device 00:11.2-1, assigned address 2
Apr 23 15:22:21 emelia kernel: input0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb1:2.0
Apr 23 15:22:22 emelia kernel: eth0: no IPv6 routers present
Apr 23 15:27:22 emelia kernel: hda: dma_timer_expiry: dma status == 0x24
Apr 23 15:27:22 emelia kernel: hda: lost interrupt
Apr 23 15:27:22 emelia kernel: hda: dma_intr: bad DMA status (dma_stat=30)
Apr 23 15:27:22 emelia kernel: hda: dma_intr: status=0x50 { DriveReady SeekComplete }
Apr 23 15:27:22 emelia kernel:
Apr 23 15:27:47 emelia kernel: hda: dma_timer_expiry: dma status == 0x24
Apr 23 15:27:47 emelia kernel: hda: lost interrupt
Apr 23 15:27:47 emelia kernel: hda: dma_intr: bad DMA status (dma_stat=30)
Apr 23 15:27:47 emelia kernel: hda: dma_intr: status=0x50 { DriveReady SeekComplete }
Apr 23 15:27:47 emelia kernel:
Apr 23 15:28:08 emelia kernel: hda: dma_timer_expiry: dma status == 0x24
Apr 23 15:28:08 emelia kernel: hda: lost interrupt
Apr 23 15:28:08 emelia kernel: hda: dma_intr: bad DMA status (dma_stat=30)
Apr 23 15:28:08 emelia kernel: hda: dma_intr: status=0x50 { DriveReady SeekComplete }
Apr 23 15:28:08 emelia kernel:
Apr 23 15:28:42 emelia kernel: hda: dma_timer_expiry: dma status == 0x24
Apr 23 15:28:42 emelia kernel: hda: lost interrupt
Apr 23 15:28:42 emelia kernel: hda: dma_intr: bad DMA status (dma_stat=30)
Apr 23 15:28:42 emelia kernel: hda: dma_intr: status=0x50 { DriveReady SeekComplete }
Apr 23 15:28:42 emelia kernel:
--
- Athanasius = Athanasius(at)miggy.org / http://www.miggy.org/
Finger athan(at)fysh.org for PGP key
"And it's me who is my enemy. Me who beats me up.
Me who makes the monsters. Me who strips my confidence." Paula Cole - ME
This archive was generated by hypermail 2b29 : Wed Apr 23 2003 - 22:00:36 EST