hda: dma_timer_expiry: dma status == 0x24
drivers/ide/ide-io.c:108: spin_lock(drivers/ide/ide.c:c04fb648) already
locked by drivers/ide/ide-io.c/948
drivers/ide/ide-io.c:990: spin_unlock(drivers/ide/ide.c:c04fb648) not locked
hda: lost interrupt
hda: dma_intr: bad DMA status (dma_stat=30)
hda: dma_intr: status=0x50 { DriveReady SeekComplete }
hda: dma_timer_expiry: dma status == 0x24
drivers/ide/ide-io.c:108: spin_lock(drivers/ide/ide.c:c04fb648) already
locked by drivers/ide/ide-io.c/948
drivers/ide/ide-io.c:990: spin_unlock(drivers/ide/ide.c:c04fb648) not locked
hda: lost interrupt
hda: dma_intr: bad DMA status (dma_stat=30)
hda: dma_intr: status=0x50 { DriveReady SeekComplete }
Got these messages while compiling XFree86.
# lspci (trimmed)
00:00.0 Host bridge: VIA Technologies, Inc. VT8375 [KM266/KL266] Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP]
00:11.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06)
# hdparm -v /dev/ide/host0/bus0/target0/lun0/disc
/dev/ide/host0/bus0/target0/lun0/disc:
multcount = 16 (on)
IO_support = 1 (32-bit)
unmaskirq = 1 (on)
using_dma = 1 (on)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
geometry = 12009/16/63, sectors = 78165360, start = 0
# hdparm -I /dev/ide/host0/bus0/target0/lun0/disc
/dev/ide/host0/bus0/target0/lun0/disc:
ATA device, with non-removable media
Model Number: WDC WD400BB-00CAA1
Serial Number: WD-WMA8F2412631
Firmware Revision: 17.07W17
Standards:
Supported: 5 4 3 2
Likely used: 6
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 78165360
device size with M = 1024*1024: 38166 MBytes
device size with M = 1000*1000: 40020 MBytes (40 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 40 Queue depth: 1
Standby timer values: spec'd by Standard, with device specific
minimum
R/W multiple sector transfer: Max = 16 Current = 16
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
SMART feature set
* Device Configuration Overlay feature set
Automatic Acoustic Management feature set
SET MAX security extension
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
HW reset results:
CBLID- below Vih
Device num = 0 determined by the jumper
Checksum: correct
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Thu May 15 2003 - 22:00:26 EST