e(1): 225280 pages. zone(2): 32768 pages. Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: VIA Product ID: VT5440B APIC at: 0xFEE00000 Processor #0 Pentium(tm) Pro APIC version 17 I/O APIC #2 Version 17 at 0xFEC00000. Enabling APIC mode: Flat. Using 1 I/O APICs Processors: 1 Kernel command line: root=/dev/hda2 ro hdb=scsi ide_setup: hdb=scsi Initializing CPU#0 Detected 1532.632 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 3060.53 BogoMIPS Memory: 1033744k/1048576k available (1276k kernel code, 14444k reserved, 480k data, 104k init, 131072k highmem) Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode cache hash table entries: 65536 (order: 7, 524288 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes) Page-cache hash table entries: 262144 (order: 8, 1048576 bytes) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000 CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000 CPU: AMD Athlon(tm) XP 1800+ stepping 02 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 ENABLING IO-APIC IRQs Setting 2 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 2 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-10, 2-11, 2-12, 2-20, 2-21, 2-22, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 number of MP IRQ sources: 21. number of IO-APIC #2 registers: 24. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178011 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0011 .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 001 01 0 0 0 0 0 1 1 51 06 001 01 0 0 0 0 0 1 1 59 07 001 01 0 0 0 0 0 1 1 61 08 001 01 0 0 0 0 0 1 1 69 09 001 01 1 1 0 1 0 1 1 71 0a 000 00 1 0 0 0 0 0 0 00 0b 000 00 1 0 0 0 0 0 0 00 0c 000 00 1 0 0 0 0 0 0 00 0d 001 01 0 0 0 0 0 1 1 79 0e 001 01 0 0 0 0 0 1 1 81 0f 001 01 0 0 0 0 0 1 1 89 10 001 01 1 1 0 1 0 1 1 91 11 001 01 1 1 0 1 0 1 1 99 12 001 01 1 1 0 1 0 1 1 A1 13 001 01 1 1 0 1 0 1 1 A9 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ16 -> 0:16 IRQ17 -> 0:17 IRQ18 -> 0:18 IRQ19 -> 0:19 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 1532.5286 MHz. ..... host bus clock speed is 266.5267 MHz. cpu: 0, clocks: 2665267, slice: 1332633 CPU0 mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel PCI: PCI BIOS revision 2.10 entry at 0xfdb21, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Using IRQ router default [1106/3074] at 00:11.0 PCI->APIC IRQ transform: (B0,I5,P0) -> 16 PCI->APIC IRQ transform: (B0,I6,P0) -> 17 PCI->APIC IRQ transform: (B0,I8,P0) -> 19 PCI->APIC IRQ transform: (B0,I9,P0) -> 16 PCI->APIC IRQ transform: (B0,I11,P0) -> 16 PCI->APIC IRQ transform: (B0,I11,P1) -> 17 PCI->APIC IRQ transform: (B0,I11,P2) -> 18 PCI->APIC IRQ transform: (B0,I17,P2) -> 9 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd allocated 32 pages and 32 bhs reserved for the highmem bounces Journalled Block Device driver loaded Detected PS/2 Mouse Port. pty: 256 Unix98 ptys configured Real Time Clock Driver v1.10e NET4: Frame Diverter 0.46 Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 00:11.1 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci00:11.1 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA hda: IC35L080AVVA07-0, ATA DISK drive hdb: _NEC DV-5700B, ATAPI CD/DVD-ROM drive blk: queue c02fd2e0, I/O limit 4095Mb (mask 0xffffffff) hdc: IC35L120AVV207-1, ATA DISK drive hdd: IBM-DTTA-350840, ATA DISK drive blk: queue c02fd734, I/O limit 4095Mb (mask 0xffffffff) blk: queue c02fd870, I/O limit 4095Mb (mask 0xffffffff) ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: attached ide-disk driver. hda: host protected area => 1 hda: 160836480 sectors (82348 MB) w/1863KiB Cache, CHS=10011/255/63, UDMA(100) hdc: attached ide-disk driver. hdc: host protected area => 1 hdc: 241254720 sectors (123522 MB) w/7965KiB Cache, CHS=15017/255/63, UDMA(100) hdd: attached ide-disk driver. hdd: host protected area => 1 hdd: 16514064 sectors (8455 MB) w/467KiB Cache, CHS=16383/16/63, UDMA(33) Partition check: hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 > hdc: hdc1 hdd: [PTBL] [1027/255/63] hdd1 SCSI subsystem driver Revision: 1.00 scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8 aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs blk: queue f7ee8494, I/O limit 4095Mb (mask 0xffffffff) Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02 Type: CD-ROM ANSI SCSI revision: 02 blk: queue f7ee8594, I/O limit 4095Mb (mask 0xffffffff) (scsi0:A:3): 20.000MB/s transfers (20.000MHz, offset 15) Vendor: PLEXTOR Model: CD-R PX-R412C Rev: 1.07 Type: CD-ROM ANSI SCSI revision: 02 blk: queue f7ee8694, I/O limit 4095Mb (mask 0xffffffff) (scsi0:A:4): 10.000MB/s transfers (10.000MHz, offset 8) NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 104k freed Adding Swap: 500432k swap-space (priority -1) EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal hda: dma_timer_expiry: dma status == 0x64 hda: lost interrupt hda: dma_intr: bad DMA status (dma_stat=70) hda: dma_intr: status=0x50 { DriveReady SeekComplete } Linux agpgart interface v0.99 (c) Jeff Hartmann agpgart: Maximum main memory to use for agp memory: 942M agpgart: Detected Via Apollo Pro KT266 chipset agpgart: AGP aperture is 64M @ 0xe0000000 hdb: attached ide-scsi driver. scsi1 : SCSI host adapter emulation for IDE ATAPI devices Vendor: _NEC Model: DV-5700B Rev: 1.92 Type: CD-ROM ANSI SCSI revision: 02 8139too Fast Ethernet driver 0.9.26 divert: allocating divert_blk for eth0 eth0: RealTek RTL8139 Fast Ethernet at 0xf8869f00, 00:50:fc:0b:87:71, IRQ 16 eth0: Identified 8139 chip type 'RTL-8139C' Forcing 10Mbps half-duplex operation. IPv6 v0.8 for NET4.0 IPv6 over IPv4 tunneling driver divert: not allocating divert_blk for non-ethernet device sit0 PCI: Setting latency timer of device 00:11.5 to 64 i2c-core.o: i2c core module i2c-algo-bit.o: i2c bit algorithm module Linux video capture interface: v1.00 i2c-core.o: driver i2c msp3400 driver registered. i2c-core.o: driver i2c TV tuner driver registered. bttv: driver version 0.7.104 loaded bttv: using 4 buffers with 2080k (8320k total) for capture bttv: Host bridge is VIA Technologies, Inc. VT8367 [KT266] usb.c: registered new driver usbdevfs usb.c: registered new driver hub Linux video capture interface: v1.00 pwc Philips PCA645/646 + PCVC675/680/690 + PCVC730/740/750 webcam module version 8.10 loaded. pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30, pwc the Creative WebCam 5, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100. pwc Default framerate set to 15. pwc Default image size set to vga [640x480]. pwc Preferred compression set to 0. usb.c: registered new driver Philips webcam pwc Philips webcam decompressor routines version 8.2 pwc Supports all cameras supported by the main module (pwc). pwc Adding decompressor for model 645. pwc Adding decompressor for model 646. pwc Adding decompressor for model 675. pwc Adding decompressor for model 680. pwc Adding decompressor for model 690. pwc Adding decompressor for model 730. pwc Adding decompressor for model 740. pwc Adding decompressor for model 750. usb.c: registered new driver audio audio.c: v1.0.0:USB Audio Class driver gameport0: Emu10k1 Gameport at 0xec00 size 8 speed 1193 kHz mice: PS/2 mouse device common for all mice usb.c: registered new driver usbmouse usbmouse.c: v1.6:USB HID Boot Protocol mouse driver usb.c: registered new driver wacom wacom.c: v1.21.3 Vojtech Pavlik wacom.c: USB Wacom Graphire and Wacom Intuos tablet driver usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik hid-core.c: USB HID support drivers usb.c: registered new driver usblp printer.c: v0.11: USB Printer Device Class driver usb.c: registered new driver usbscanner scanner.c: 0.4.12:USB Scanner Driver usb-ohci.c: USB OHCI at membase 0xf8a98000, IRQ 17 usb-ohci.c: usb-00:0b.1, NEC Corporation USB (#2) usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected usb-ohci.c: USB OHCI at membase 0xf8a9a000, IRQ 16 usb-ohci.c: usb-00:0b.0, NEC Corporation USB usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 3 ports detected usb-uhci.c: $Revision: 1.275 $ time 13:39:48 May 29 2003 usb-uhci.c: High bandwidth mode enabled usb-uhci.c: v1.275:USB Universal Host Controller Interface driver i2c-proc.o version 2.6.1 (20010825) i2c-isa.o version 2.6.5 (20020915) tuner: ignoring ISA main adapter i2c adapter [id=0x50000] i2c-core.o: adapter ISA main adapter registered as adapter 0. i2c-isa.o: ISA bus access for i2c modules initialized. i2c-viapro.o version 2.6.5 (20020915) i2c-viapro.o: Found Via VT8233 device tuner: ignoring SMBus Via Pro adapter at 0400 i2c adapter [id=0x40002] i2c-core.o: adapter SMBus Via Pro adapter at 0400 registered as adapter 1. i2c-viapro.o: Via Pro SMBus detected and initialized w83781d.o version 2.6.5 (20020915) i2c-core.o: driver W83781D sensor driver registered. i2c-core.o: client [W83627HF chip] registered to adapter [ISA main adapter](pos. 0). hub.c: new USB device 00:0b.0-1, assigned address 2 input0: Microsoft Microsoft Trackball OpticalŪ on usb2:2.0 i2c-core.o: client [W83627HF chip] registered to adapter [SMBus Via Pro adapter at 0400](pos. 0). i2c-core.o: client [W83627HF subclient] registered to adapter [SMBus Via Pro adapter at 0400](pos. 1). i2c-core.o: client [W83627HF subclient] registered to adapter [SMBus Via Pro adapter at 0400](pos. 2). hub.c: new USB device 00:0b.0-2, assigned address 3 usb.c: USB device 3 (vend/prod 0x6b9/0x4061) is not claimed by any active driver. eeprom.o version 2.6.5 (20020915) i2c-core.o: driver EEPROM READER registered. i2c-core.o: client [EEPROM chip] registered to adapter [SMBus Via Pro adapter at 0400](pos. 3). i2c-core.o: client [EEPROM chip] registered to adapter [SMBus Via Pro adapter at 0400](pos. 4). i2c-core.o: client [EEPROM chip] registered to adapter [SMBus Via Pro adapter at 0400](pos. 5). adm1021.o version 2.6.5 (20020915) i2c-core.o: driver ADM1021, MAX1617 sensor driver registered. i2c-core.o: client [MAX1617 chip] registered to adapter [SMBus Via Pro adapter at 0400](pos. 6). apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16) CSLIP: code copyright 1989 Regents of the University of California PPP generic driver version 2.4.2 LVM version 1.0.7(28/03/2003) module loaded loop: loaded (max 8 devices) kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,7), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,0), internal journal EXT3-fs: mounted filesystem with ordered data mode. ehci-hcd 00:0b.2: NEC Corporation USB 2.0 ehci-hcd 00:0b.2: irq 18, pci mem f8b00e00 usb.c: new USB bus registered, assigned bus number 3 PCI: 00:0b.2 PCI cache line size set incorrectly (32 bytes) by BIOS/FW. PCI: 00:0b.2 PCI cache line size corrected to 64. ehci-hcd 00:0b.2: USB 2.0 enabled, EHCI 0.95, driver 2003-Jan-22 hub.c: USB hub found hub.c: 5 ports detected usb.c: USB disconnect on device 00:0b.0-1 address 2 usb.c: USB disconnect on device 00:0b.0-2 address 3 uhci.c: USB Universal Host Controller Interface driver v1.1 usb-uhci.c: $Revision: 1.275 $ time 13:39:48 May 29 2003 usb-uhci.c: High bandwidth mode enabled usb-uhci.c: v1.275:USB Universal Host Controller Interface driver atmsvc: no signaling demon hub.c: new USB device 00:0b.0-1, assigned address 4 input0: Microsoft Microsoft Trackball OpticalŪ on usb2:4.0 hub.c: new USB device 00:0b.0-2, assigned address 5 usb.c: USB device 5 (vend/prod 0x6b9/0x4061) is not claimed by any active driver. eth0: Setting full-duplex based on auto-negotiated partner ability 0000. divert: not allocating divert_blk for non-ethernet device eth1 hp100: eth1: Busmaster mode enabled. hp100: eth1: HP J2970 at 0xe000, IRQ 19, PCI bus, 32k SRAM (rx/tx 75%). hp100: eth1: Adapter is attached to 10Mb/s network.