Hi,
just tried to run 2.5.73bk1 on my desktop, but it hangs somewhere in
the IDE setup. The identical hardware boots 2.4.x (currently 21ck3)
without problems. I wrote down the output (see below).
The machine is an Athlon-1100 with an on-board RAID controller (which
I use as additional IDE controllers).
I also append the corresponding output from 2.4.21 (using "hdb=scsi"),
an extract of the config (hopefully including all relevant parts), and
lspci output.
so long
Norbert
2.5.73bk1:
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 16
VP_IDE: not 100%% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci00:07.1
ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:pio, hdd:DMA
hda: KENWOOD CD-ROM UCR-421 V221F, ATAPI CD/DVD-ROM drive
hdb: R/RW 4x4x24, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdd: Maxtor 91152D8, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
CMD649: IDE controller at PCI slot 00:10.0
CMD649: chipset revision 1
CMD649: not 100%% native mode: will probe irqs later
ide2: BM-DMA at 0xe400-0xe407, BIOS settings: hde:pio, hdf:DMA
ide3: BM-DMA at 0xe408-0xe40f, BIOS settings: hdg:pio, hdh:DMA
hdf: IBM-DJNA-370910, ATA DISK drive
ide2 at 0xd400-0xd407,0xd802 on irq 12
*** hangs right here ***
2.4.21ck3:
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 16
VP_IDE: not 100%% native mode: will probe irqs later
VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci00:07.1
ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:pio, hdd:DMA
CMD649: IDE controller at PCI slot 00:10.0
CMD649: chipset revision 1
CMD649: not 100%% native mode: will probe irqs later
ide2: BM-DMA at 0xe400-0xe407, BIOS settings: hde:pio, hdf:DMA
ide3: BM-DMA at 0xe408-0xe40f, BIOS settings: hdg:pio, hdh:DMA
hda: KENWOOD CD-ROM UCR-421 V221F, ATAPI CD/DVD-ROM drive
hdb: R/RW 4x4x24, ATAPI CD/DVD-ROM drive
hdd: Maxtor 91152D8, ATA DISK drive
blk: queue c032dd7c, I/O limit 4095Mb (mask 0xffffffff)
hdf: IBM-DJNA-370910, ATA DISK drive
blk: queue c032e1d8, I/O limit 4095Mb (mask 0xffffffff)
hdh: QUANTUM FIREBALLP AS20.5, ATA DISK drive
blk: queue c032e634, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xd400-0xd407,0xd802 on irq 12
ide3 at 0xdc00-0xdc07,0xe002 on irq 12
hdd: attached ide-disk driver.
hdd: host protected area => 1
hdd: 22510656 sectors (11525 MB) w/256KiB Cache, CHS=22332/16/63, UDMA(33)
hdf: attached ide-disk driver.
hdf: host protected area => 1
hdf: 17803440 sectors (9115 MB) w/1966KiB Cache, CHS=17662/16/63, UDMA(33)
hdh: attached ide-disk driver.
hdh: host protected area => 1
hdh: 40132503 sectors (20548 MB) w/1902KiB Cache, CHS=39813/16/63, UDMA(100)
hda: attached ide-cdrom driver.
hda: ATAPI 68X CD-ROM drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
ide-cd: passing drive hdb to ide-scsi emulation.
hdb: attached ide-scsi driver.
Partition check:
hdd: hdd1 hdd2 < hdd5 hdd6 hdd7 hdd8 >
hdf: hdf1
hdh: hdh1 < hdh5 hdh6 > hdh2
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: IDE-CD Model: R/RW 4x4x24 Rev: C12a
Type: CD-ROM ANSI SCSI revision: 02
*** goes on with network etc. ***
CONFIG_GENERIC_ISA_DMA=y
CONFIG_PREEMPT=y
CONFIG_X86_UP_APIC=y
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_NOHIGHMEM=y
CONFIG_ACPI=y
# CONFIG_ACPI_HT_ONLY is not set
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_AC=m
# CONFIG_ACPI_BATTERY is not set
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_FAN=m
CONFIG_ACPI_PROCESSOR=m
CONFIG_ACPI_THERMAL=m
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_TOSHIBA is not set
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_BUS=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
# CONFIG_PCI_LEGACY_PROC is not set
CONFIG_PCI_NAMES=y
CONFIG_ISA=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
CONFIG_HOTPLUG=y
# CONFIG_PCMCIA is not set
CONFIG_PCMCIA_PROBE=y
# CONFIG_HOTPLUG_PCI is not set
CONFIG_PNP=y
CONFIG_PNP_NAMES=y
# CONFIG_PNP_DEBUG is not set
CONFIG_ISAPNP=y
CONFIG_PNPBIOS=y
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=m
# CONFIG_BLK_DEV_NBD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_INITRD=y
# CONFIG_LBD is not set
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_IDEDISK_STROKE is not set
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDEFLOPPY=m
CONFIG_BLK_DEV_IDESCSI=y
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_IDE_TASKFILE_IO=y
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDE_TCQ is not set
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
CONFIG_BLK_DEV_ADMA=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
CONFIG_BLK_DEV_CMD64X=y
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_RZ1000 is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
CONFIG_BLK_DEV_VIA82CXXX=y
# CONFIG_IDE_CHIPSETS is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_BLK_DEV_IDE_MODES=y
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=m
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=y
lspci -v:
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 02)
Flags: bus master, medium devsel, latency 0
Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management version 2
00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: d6000000-d7ffffff
Prefetchable memory behind bridge: d4000000-d5ffffff
Capabilities: [80] Power Management version 2
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT8235 Bus Master ATA133/100/66/33 IDE
Flags: bus master, medium devsel, latency 32
I/O ports at c000 [size=16]
Capabilities: [c0] Power Management version 2
00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 10) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 12
I/O ports at c400 [size=32]
Capabilities: [80] Power Management version 2
00:07.3 USB Controller: VIA Technologies, Inc. USB (rev 10) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 12
I/O ports at c800 [size=32]
Capabilities: [80] Power Management version 2
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
Flags: medium devsel, IRQ 5
Capabilities: [68] Power Management version 2
00:0b.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)
Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at cc00 [size=128]
Memory at d9000000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 1
00:0f.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at d000 [size=256]
Capabilities: [c0] Power Management version 2
00:10.0 RAID bus controller: CMD Technology Inc PCI0649 (rev 01)
Subsystem: CMD Technology Inc PCI0649
Flags: bus master, medium devsel, latency 64, IRQ 12
I/O ports at d400 [size=8]
I/O ports at d800 [size=4]
I/O ports at dc00 [size=8]
I/O ports at e000 [size=4]
I/O ports at e400 [size=16]
Expansion ROM at <unassigned> [disabled] [size=512K]
Capabilities: [60] Power Management version 2
01:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15) (prog-if 00 [VGA])
Subsystem: VISIONTEK: Unknown device 0005
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 10
Memory at d6000000 (32-bit, non-prefetchable) [size=16M]
Memory at d4000000 (32-bit, prefetchable) [size=32M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Capabilities: [44] AGP version 2.0
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Mon Jun 23 2003 - 22:00:42 EST