This patch updates the 2.5 swim3 driver as follows:
- fix compile problems due to irqreturn_t changes not having been
implemented in swim3.c (trivial: #include <linux/interrupt.h> and
update the return type of swim3_interrupt())
- fix absence of initialisation since 2.5.1 when the swim3_init()
call was removed from ll_rw_block.c (trivial: #include <linux/module.h>
and use module_init(swim3_init))
- merge Paul Mackerras' update to the 2.4 swim3.c driver from March 29
this year; this fixes write performance and reliability issues just
like they did with the 2.4 driver
- fix compile warning by removing the now unused floppy_off() function
The resulting driver works reliably for me in raw access modes; I use
it mostly for building boot floppies (hformat + hcopy vmlinux.coff).
/Mikael
diff -ruN linux-2.5.74/drivers/block/swim3.c linux-2.5.74.ppc-swim3-fixes/drivers/block/swim3.c
--- linux-2.5.74/drivers/block/swim3.c 2003-05-05 22:56:29.000000000 +0200
+++ linux-2.5.74.ppc-swim3-fixes/drivers/block/swim3.c 2003-07-03 19:34:37.000000000 +0200
@@ -26,6 +26,8 @@
#include <linux/ioctl.h>
#include <linux/blk.h>
#include <linux/devfs_fs_kernel.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
#include <asm/io.h>
#include <asm/dbdma.h>
#include <asm/prom.h>
@@ -145,7 +147,7 @@
#define RELAX 3 /* also eject in progress */
#define READ_DATA_0 4
#define TWOMEG_DRIVE 5
-#define SINGLE_SIDED 6
+#define SINGLE_SIDED 6 /* drive or diskette is 4MB type? */
#define DRIVE_PRESENT 7
#define DISK_IN 8
#define WRITE_PROT 9
@@ -185,6 +187,7 @@
int req_sector; /* sector number ditto */
int scount; /* # sectors we're transferring at present */
int retries;
+ int settle_time;
int secpercyl; /* disk geometry information */
int secpertrack;
int total_secs;
@@ -233,8 +236,9 @@
static void act(struct floppy_state *fs);
static void scan_timeout(unsigned long data);
static void seek_timeout(unsigned long data);
+static void settle_timeout(unsigned long data);
static void xfer_timeout(unsigned long data);
-static void swim3_interrupt(int irq, void *dev_id, struct pt_regs *regs);
+static irqreturn_t swim3_interrupt(int irq, void *dev_id, struct pt_regs *regs);
/*static void fd_dma_interrupt(int irq, void *dev_id, struct pt_regs *regs);*/
static int grab_drive(struct floppy_state *fs, enum swim_state state,
int interruptible);
@@ -275,7 +279,6 @@
udelay(2);
out_8(&sw->select, sw->select & ~LSTRB);
udelay(1);
- out_8(&sw->select, RELAX);
}
static int swim3_readbit(struct floppy_state *fs, int bit)
@@ -284,9 +287,8 @@
int stat;
swim3_select(fs, bit);
- udelay(10);
+ udelay(1);
stat = in_8(&sw->status);
- out_8(&sw->select, RELAX);
return (stat & DATA) == 0;
}
@@ -375,13 +377,13 @@
static inline void scan_track(struct floppy_state *fs)
{
volatile struct swim3 *sw = fs->swim3;
- int xx;
swim3_select(fs, READ_DATA_0);
- xx = sw->intr; /* clear SEEN_SECTOR bit */
+ in_8(&sw->intr); /* clear SEEN_SECTOR bit */
+ in_8(&sw->error);
+ out_8(&sw->intr_enable, SEEN_SECTOR);
out_8(&sw->control_bis, DO_ACTION);
/* enable intr when track found */
- out_8(&sw->intr_enable, ERROR_INTR | SEEN_SECTOR);
set_timeout(fs, HZ, scan_timeout); /* enable timeout */
}
@@ -396,12 +398,14 @@
swim3_action(fs, SEEK_NEGATIVE);
sw->nseek = -n;
}
- fs->expect_cyl = (fs->cur_cyl > 0)? fs->cur_cyl + n: -1;
+ fs->expect_cyl = (fs->cur_cyl >= 0)? fs->cur_cyl + n: -1;
swim3_select(fs, STEP);
- out_8(&sw->control_bis, DO_SEEK);
+ in_8(&sw->error);
/* enable intr when seek finished */
- out_8(&sw->intr_enable, ERROR_INTR | SEEK_DONE);
- set_timeout(fs, HZ/2, seek_timeout); /* enable timeout */
+ out_8(&sw->intr_enable, SEEK_DONE);
+ out_8(&sw->control_bis, DO_SEEK);
+ set_timeout(fs, 3*HZ, seek_timeout); /* enable timeout */
+ fs->settle_time = 0;
}
static inline void init_dma(struct dbdma_cmd *cp, int cmd,
@@ -449,18 +453,21 @@
}
++cp;
out_le16(&cp->command, DBDMA_STOP);
+ out_8(&sw->control_bic, DO_ACTION | WRITE_SECTORS);
+ in_8(&sw->error);
+ out_8(&sw->control_bic, DO_ACTION | WRITE_SECTORS);
+ if (rq_data_dir(fd_req) == WRITE)
+ out_8(&sw->control_bis, WRITE_SECTORS);
+ in_8(&sw->intr);
out_le32(&dr->control, (RUN << 16) | RUN);
- out_8(&sw->control_bis,
- (rq_data_dir(fd_req) == WRITE? WRITE_SECTORS: 0) | DO_ACTION);
/* enable intr when transfer complete */
- out_8(&sw->intr_enable, ERROR_INTR | TRANSFER_DONE);
+ out_8(&sw->intr_enable, TRANSFER_DONE);
+ out_8(&sw->control_bis, DO_ACTION);
set_timeout(fs, 2*HZ, xfer_timeout); /* enable timeout */
}
static void act(struct floppy_state *fs)
{
- volatile struct swim3 *sw = fs->swim3;
-
for (;;) {
switch (fs->state) {
case idle:
@@ -493,20 +500,10 @@
return;
case settling:
- /* wait for SEEK_COMPLETE to become true */
- swim3_select(fs, SEEK_COMPLETE);
- udelay(10);
- out_8(&sw->intr_enable, ERROR_INTR | DATA_CHANGED);
- in_8(&sw->intr); /* clear DATA_CHANGED */
- if (in_8(&sw->status) & DATA) {
- /* seek_complete is not yet true */
- set_timeout(fs, HZ/2, seek_timeout);
- return;
- }
- out_8(&sw->intr_enable, 0);
- in_8(&sw->intr);
- fs->state = locating;
- break;
+ /* check for SEEK_COMPLETE after 30ms */
+ fs->settle_time = (HZ + 32) / 33;
+ set_timeout(fs, fs->settle_time, settle_timeout);
+ return;
case do_transfer:
if (fs->cur_cyl != fs->req_cyl) {
@@ -538,7 +535,7 @@
volatile struct swim3 *sw = fs->swim3;
fs->timeout_pending = 0;
- out_8(&sw->control_bic, DO_ACTION);
+ out_8(&sw->control_bic, DO_ACTION | WRITE_SECTORS);
out_8(&sw->select, RELAX);
out_8(&sw->intr_enable, 0);
fs->cur_cyl = -1;
@@ -558,20 +555,34 @@
volatile struct swim3 *sw = fs->swim3;
fs->timeout_pending = 0;
- if (fs->state == settling) {
- printk(KERN_ERR "swim3: MSI sel=%x ctrl=%x stat=%x intr=%x ie=%x\n",
- sw->select, sw->control, sw->status, sw->intr, sw->intr_enable);
- }
out_8(&sw->control_bic, DO_SEEK);
out_8(&sw->select, RELAX);
out_8(&sw->intr_enable, 0);
- if (fs->state == settling && swim3_readbit(fs, SEEK_COMPLETE)) {
- /* printk(KERN_DEBUG "swim3: missed settling interrupt\n"); */
+ printk(KERN_ERR "swim3: seek timeout\n");
+ end_request(fd_req, 0);
+ fs->state = idle;
+ start_request(fs);
+}
+
+static void settle_timeout(unsigned long data)
+{
+ struct floppy_state *fs = (struct floppy_state *) data;
+ volatile struct swim3 *sw = fs->swim3;
+
+ fs->timeout_pending = 0;
+ if (swim3_readbit(fs, SEEK_COMPLETE)) {
+ out_8(&sw->select, RELAX);
fs->state = locating;
act(fs);
return;
}
- printk(KERN_ERR "swim3: seek timeout\n");
+ out_8(&sw->select, RELAX);
+ if (fs->settle_time < 2*HZ) {
+ ++fs->settle_time;
+ set_timeout(fs, 1, settle_timeout);
+ return;
+ }
+ printk(KERN_ERR "swim3: seek settle timeout\n");
end_request(fd_req, 0);
fs->state = idle;
start_request(fs);
@@ -584,9 +595,13 @@
struct dbdma_regs *dr = fs->dma;
struct dbdma_cmd *cp = fs->dma_cmd;
unsigned long s;
+ int n;
fs->timeout_pending = 0;
st_le32(&dr->control, RUN << 16);
+ /* We must wait a bit for dbdma to stop */
+ for (n = 0; (in_le32(&dr->status) & ACTIVE) && n < 1000; n++)
+ udelay(1);
out_8(&sw->intr_enable, 0);
out_8(&sw->control_bic, WRITE_SECTORS | DO_ACTION);
out_8(&sw->select, RELAX);
@@ -605,7 +620,7 @@
start_request(fs);
}
-static void swim3_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+static irqreturn_t swim3_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
struct floppy_state *fs = (struct floppy_state *) dev_id;
volatile struct swim3 *sw = fs->swim3;
@@ -614,18 +629,15 @@
struct dbdma_regs *dr;
struct dbdma_cmd *cp;
- err = in_8(&sw->error);
intr = in_8(&sw->intr);
-#if 0
- printk("swim3 intr state=%d intr=%x err=%x\n", fs->state, intr, err);
-#endif
+ err = (intr & ERROR_INTR)? in_8(&sw->error): 0;
if ((intr & ERROR_INTR) && fs->state != do_transfer)
printk(KERN_ERR "swim3_interrupt, state=%d, dir=%lx, intr=%x, err=%x\n",
fs->state, rq_data_dir(fd_req), intr, err);
switch (fs->state) {
case locating:
if (intr & SEEN_SECTOR) {
- out_8(&sw->control_bic, DO_ACTION);
+ out_8(&sw->control_bic, DO_ACTION | WRITE_SECTORS);
out_8(&sw->select, RELAX);
out_8(&sw->intr_enable, 0);
del_timer(&fs->timeout);
@@ -675,19 +687,33 @@
case do_transfer:
if ((intr & (ERROR_INTR | TRANSFER_DONE)) == 0)
break;
- dr = fs->dma;
- cp = fs->dma_cmd;
- /* We must wait a bit for dbdma to complete */
- for (n=0; (in_le32(&dr->status) & ACTIVE) && n < 1000; n++)
- udelay(10);
- DBDMA_DO_STOP(dr);
out_8(&sw->intr_enable, 0);
out_8(&sw->control_bic, WRITE_SECTORS | DO_ACTION);
out_8(&sw->select, RELAX);
del_timer(&fs->timeout);
fs->timeout_pending = 0;
+ dr = fs->dma;
+ cp = fs->dma_cmd;
if (rq_data_dir(fd_req) == WRITE)
++cp;
+ /*
+ * Check that the main data transfer has finished.
+ * On writing, the swim3 sometimes doesn't use
+ * up all the bytes of the postamble, so we can still
+ * see DMA active here. That doesn't matter as long
+ * as all the sector data has been transferred.
+ */
+ if ((intr & ERROR_INTR) == 0 && cp->xfer_status == 0) {
+ /* wait a little while for DMA to complete */
+ for (n = 0; n < 100; ++n) {
+ if (cp->xfer_status != 0)
+ break;
+ udelay(1);
+ barrier();
+ }
+ }
+ /* turn off DMA */
+ out_le32(&dr->control, (RUN | PAUSE) << 16);
stat = ld_le16(&cp->xfer_status);
resid = ld_le16(&cp->res_count);
if (intr & ERROR_INTR) {
@@ -743,6 +769,7 @@
default:
printk(KERN_ERR "swim3: don't know what to do in state %d\n", fs->state);
}
+ return IRQ_HANDLED;
}
/*
@@ -794,16 +821,19 @@
if (err)
return err;
swim3_action(fs, EJECT);
- for (n = 2*HZ; n > 0; --n) {
- if (swim3_readbit(fs, RELAX))
- break;
+ for (n = 20; n > 0; --n) {
if (signal_pending(current)) {
err = -EINTR;
break;
}
+ swim3_select(fs, RELAX);
current->state = TASK_INTERRUPTIBLE;
schedule_timeout(1);
+ if (swim3_readbit(fs, DISK_IN) == 0)
+ break;
}
+ swim3_select(fs, RELAX);
+ udelay(150);
fs->ejected = 1;
release_drive(fs);
return err;
@@ -848,29 +878,31 @@
if (fs->ref_count == 0) {
if (fs->media_bay && check_media_bay(fs->media_bay, MB_FD))
return -ENXIO;
- out_8(&sw->mode, 0x95);
- out_8(&sw->control_bic, 0xff);
out_8(&sw->setup, S_IBM_DRIVE | S_FCLK_DIV2);
+ out_8(&sw->control_bic, 0xff);
+ out_8(&sw->mode, 0x95);
udelay(10);
out_8(&sw->intr_enable, 0);
out_8(&sw->control_bis, DRIVE_ENABLE | INTR_ENABLE);
swim3_action(fs, MOTOR_ON);
fs->write_prot = -1;
fs->cur_cyl = -1;
- for (n = HZ; n > 0; --n) {
- if (swim3_readbit(fs, SEEK_COMPLETE))
+ for (n = 0; n < 2 * HZ; ++n) {
+ if (n >= HZ/30 && swim3_readbit(fs, SEEK_COMPLETE))
break;
if (signal_pending(current)) {
err = -EINTR;
break;
}
+ swim3_select(fs, RELAX);
current->state = TASK_INTERRUPTIBLE;
schedule_timeout(1);
}
if (err == 0 && (swim3_readbit(fs, SEEK_COMPLETE) == 0
|| swim3_readbit(fs, DISK_IN) == 0))
err = -ENXIO;
- swim3_action(fs, 9);
+ swim3_action(fs, SETMFM);
+ swim3_select(fs, RELAX);
} else if (fs->ref_count == -1 || filp->f_flags & O_EXCL)
return -EBUSY;
@@ -893,6 +925,7 @@
if (fs->ref_count == 0) {
swim3_action(fs, MOTOR_OFF);
out_8(&sw->control_bic, DRIVE_ENABLE | INTR_ENABLE);
+ swim3_select(fs, RELAX);
}
return err;
}
@@ -912,6 +945,7 @@
if (fs->ref_count > 0 && --fs->ref_count == 0) {
swim3_action(fs, MOTOR_OFF);
out_8(&sw->control_bic, 0xff);
+ swim3_select(fs, RELAX);
}
return 0;
}
@@ -934,15 +968,17 @@
sw = fs->swim3;
grab_drive(fs, revalidating, 0);
out_8(&sw->intr_enable, 0);
- out_8(&sw->control_bis, DRIVE_ENABLE | INTR_ENABLE);
- swim3_action(fs, MOTOR_ON);
+ out_8(&sw->control_bis, DRIVE_ENABLE);
+ swim3_action(fs, MOTOR_ON); /* necessary? */
fs->write_prot = -1;
fs->cur_cyl = -1;
+ mdelay(1);
for (n = HZ; n > 0; --n) {
if (swim3_readbit(fs, SEEK_COMPLETE))
break;
if (signal_pending(current))
break;
+ swim3_select(fs, RELAX);
current->state = TASK_INTERRUPTIBLE;
schedule_timeout(1);
}
@@ -952,17 +988,14 @@
swim3_action(fs, MOTOR_OFF);
else {
fs->ejected = 0;
- swim3_action(fs, 9);
+ swim3_action(fs, SETMFM);
}
+ swim3_select(fs, RELAX);
release_drive(fs);
return ret;
}
-static void floppy_off(unsigned int nr)
-{
-}
-
static struct block_device_operations floppy_fops = {
.open = floppy_open,
.release = floppy_release,
@@ -1097,3 +1130,5 @@
return 0;
}
+
+module_init(swim3_init)
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Mon Jul 07 2003 - 22:00:21 EST