Re: Omnibook PCMCIA slots unusable after suspend.
From: Jon Fairbairn
Date: Thu Sep 11 2003 - 11:04:56 EST
On 2003-09-10 at 23:45BST Russell King wrote:
> On Wed, Sep 10, 2003 at 10:22:32PM +0100, Jon Fairbairn wrote:
> > In short: I'm using an HP Ombibook 800CT, have started using
> > a Carbus PCMCIA network card and am losing the card after
> > suspends.
>
> I'm only interested in the 2.6.0-test5 results.
OK. Pause for recompilation...
> Please run lspci -vvb twice - once when you have just booted
> the machine, and once when you resume.
The following is done without unloading the modules round
the suspend.
Before:
------
00:00.0 Host bridge: VLSI Technology Inc 82C535 (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
00:01.0 PCI bridge: VLSI Technology Inc 82C534 [Eagle] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00004000-00007fff
Memory behind bridge: 20000000-2fffffff
Prefetchable memory behind bridge: 30000000-3fffffff
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset+ FastB2B-
00:02.0 Class ff00: VLSI Technology Inc 82C532 (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:03.0 VGA compatible controller: Neomagic Corporation NM2070 [MagicGraph 128] (rev 01) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: Memory at c0000000 (32-bit, prefetchable)
00:04.0 CardBus bridge: Texas Instruments PCI1130 (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 000e6000 (32-bit, non-prefetchable)
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10000000-103ff000 (prefetchable)
Memory window 1: 10400000-107ff000
I/O window 0: 00008000-000080ff
I/O window 1: 00008400-000084ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:04.1 CardBus bridge: Texas Instruments PCI1130 (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin B routed to IRQ 7
Region 0: Memory at 000e7000 (32-bit, non-prefetchable)
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 10800000-10bff000 (prefetchable)
Memory window 1: 10c00000-10fff000
I/O window 0: 00008800-000088ff
I/O window 1: 00008c00-00008cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:06.0 IRDA controller: VLSI Technology Inc 82C147 (rev 02)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at 1000 [disabled]
02:00.0 Ethernet controller: Linksys Fast Ethernet 10/100 (rev 11)
Subsystem: Netgear FA511 10/100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min, 63750ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 8000
Region 1: Memory at 10400000 (32-bit, non-prefetchable)
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
------
After:
------
00:00.0 Host bridge: VLSI Technology Inc 82C535 (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
00:01.0 PCI bridge: VLSI Technology Inc 82C534 [Eagle] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00004000-00007fff
Memory behind bridge: 20000000-2fffffff
Prefetchable memory behind bridge: 30000000-3fffffff
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset+ FastB2B-
00:02.0 Class ff00: VLSI Technology Inc 82C532 (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:03.0 VGA compatible controller: Neomagic Corporation NM2070 [MagicGraph 128] (rev 01) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: Memory at c0000000 (32-bit, prefetchable)
00:04.0 CardBus bridge: Texas Instruments PCI1130 (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 000e6000 (32-bit, non-prefetchable)
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10000000-103ff000 (prefetchable)
Memory window 1: 10400000-107ff000
I/O window 0: 00008000-000080ff
I/O window 1: 00008400-000084ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:04.1 CardBus bridge: Texas Instruments PCI1130 (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin B routed to IRQ 7
Region 0: Memory at 000e7000 (32-bit, non-prefetchable)
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 10800000-10bff000 (prefetchable)
Memory window 1: 10c00000-10fff000
I/O window 0: 00008800-000088ff
I/O window 1: 00008c00-00008cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:06.0 IRDA controller: VLSI Technology Inc 82C147 (rev 02)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at 1000 [disabled]
02:00.0 Class ffff: Linksys Fast Ethernet 10/100 (rev ff) (prog-if ff)
!!! Unknown header type 7f
------
So there's a Reset- v a Reset+ there.
Curiously, the output after a suspend on mains is the same
(says diff) as the output after a suspend on battery, even
though the former doesn't stop it working while the latter
does.
> > ...
> > Sep 6 23:23:55 graffito kernel: Socket status: 2a035c8a
>
> It looks like the cardbus controller configuration wasn't correctly
> restored.
Indeed, though it always seems to give the same dodgy looking
status.
> --
> Russell King (rmk@xxxxxxxxxxxxxxxx) http://www.arm.linux.org.uk/personal/
> Linux kernel maintainer of:
> 2.6 ARM Linux - http://www.arm.linux.org.uk/
Wish I still had an ARM...
--
Jón Fairbairn
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/