Re: Error message when aic7xxx is probing devices "Badness in kobject_get" on 2.6.0-test10

From: Mike Anderson
Date: Mon Nov 24 2003 - 10:55:14 EST


I sent a response last night to the list for another mail on this same
badness output.

You can find the mail here.
http://marc.theaimsgroup.com/?l=linux-kernel&m=106966122108719&w=2

The mail points to a patch sent to the linux-scsi list. You can find the
archive of this patch here.
http://marc.theaimsgroup.com/?l=linux-scsi&m=106940008217622&w=2

Let me know if this does not stop the badness message.

Jean-Yves Simon [lethalwp@xxxxxxxxxx] wrote:
> Hello,
>
> [1.] One line summary of the problem:
> on boot, an error appear while the aic7xxx module loads on a
> 2.6.0-test10.
>
>
> [2.] Full description of the problem/report:
> device used:
> 00:11.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
>
> dmesg output:
> ---
> RAMDISK: Compressed image found at block 0
> VFS: Mounted root (ext2 filesystem).
> SCSI subsystem initialized
> PCI: Found IRQ 5 for device 0000:00:11.0
> scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.35
> <Adaptec 29160 Ultra160 SCSI adapter>
> aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
>
> (scsi0:A:0): 20.000MB/s transfers (20.000MHz, offset 15)
> (scsi0:A:1): 10.000MB/s transfers (10.000MHz, offset 15)
> (scsi0:A:4): 20.000MB/s transfers (20.000MHz, offset 16)
> (scsi0:A:6): 160.000MB/s transfers (80.000MHz DT, offset 63, 16bit)
> Badness in kobject_get at lib/kobject.c:439
> Call Trace:
> [<c01c0a3f>] kobject_get+0x4f/0x60
> [<c0203b58>] get_device+0x18/0x20
> [<e0832e0c>] scsi_device_get+0x2c/0xa0 [scsi_mod]
> [<e0832f3b>] __scsi_iterate_devices+0x4b/0x90 [scsi_mod]
> [<e0837507>] scsi_run_host_queues+0x17/0x50 [scsi_mod]
> [<e08ae764>] ahc_linux_release_simq+0x94/0xe0 [aic7xxx]
> [<e08a9b9d>] ahc_linux_dv_thread+0x1fd/0x2c0 [aic7xxx]
> [<e08a99a0>] ahc_linux_dv_thread+0x0/0x2c0 [aic7xxx]
> [<c0108d75>] kernel_thread_helper+0x5/0x10
>
> Vendor: WDIGTL Model: ENTERPRISE Rev: 1.61
> Type: Direct-Access ANSI SCSI revision: 02
> scsi0:A:0:0: Tagged Queuing enabled. Depth 253
> SCSI device sda: 8515173 512-byte hdwr sectors (4360 MB)
> SCSI device sda: drive cache: write back
> sda: sda1 sda2 < sda5 > sda3
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> Vendor: PLEXTOR Model: CD-ROM PX-20TS Rev: 1.00
> Type: CD-ROM ANSI SCSI revision: 02
> Vendor: PLEXTOR Model: CD-R PX-W1210S Rev: 1.06
> Type: CD-ROM ANSI SCSI revision: 02
> Vendor: IBM Model: DDYS-T36950N Rev: S96H
> Type: Direct-Access ANSI SCSI revision: 03
> scsi0:A:6:0: Tagged Queuing enabled. Depth 253
> SCSI device sdb: 71687340 512-byte hdwr sectors (36704 MB)
> SCSI device sdb: drive cache: write back
> sdb: sdb1 sdb2 sdb3 < sdb5 >
> Attached scsi disk sdb at scsi0, channel 0, id 6, lun 0
> kjournald starting. Commit interval 5 seconds
> ---
>
> [3.] Keywords (i.e., modules, networking, kernel):
> kernel
>
> [4.] Kernel version (from /proc/version):
> Linux version 2.6.0-test10 (root@xxxxxxxxxxxxxxx) (gcc version 3.3.2
> 20031022 (Red Hat Linux 3.3.2-1)) #1 Mon Nov 24 13:00:22 CET 2003
>
>
> [5.] Output of Oops.. message (if applicable) with symbolic information
> resolved (see Documentation/oops-tracing.txt)
> It's not an Oops, but an error, see [2.]
>
> [6.] A small shell script or example program which triggers the
> problem (if possible)
> Just boot with the aic7xxx.ko module in the initrd, i suppose it will do
> this too if you load it manually with modprobe
>
>
> [7.] Environment
> [7.1.] Software (add the output of the ver_linux script here)
> If some fields are empty or look unusual you may have an old version.
> Compare to the current minimal requirements in Documentation/Changes.
>
> Linux little.lethalwp 2.6.0-test10 #1 Mon Nov 24 13:00:22 CET 2003 i686
> i686 i386 GNU/Linux
>
> Gnu C 3.3.2
> Gnu make 3.79.1
> util-linux 2.11y
> mount 2.11y
> module-init-tools 2.4.25
> e2fsprogs 1.34
> reiserfsprogs 3.6.8
> quota-tools 3.06.
> PPP 2.4.1
> nfs-utils 1.0.6
> Linux C Library 2.3.2
> Dynamic linker (ldd) 2.3.2
> Procps 2.0.17
> Net-tools 1.60
> Kbd 1.08
> Sh-utils 5.0
> Modules Loaded snd_pcm_oss agpgart nvidia vmnet vmmon nfs ide_cd
> cdrom snd_mixer_oss uhci_hcd eeprom i2c_sensor usb_storage i2c_viapro
> i2c_core binfmt_misc parport_pc lp parport nfsd exportfs lockd sunrpc
> capability commoncap iptable_filter ip_tables 8139too mii crc32 ipv6
> microcode reiserfs nls_iso8859_1 nls_cp437 vfat fat snd_seq_midi
> snd_emu10k1_synth snd_emux_synth snd_seq_virmidi snd_seq_midi_emul
> snd_seq_oss snd_seq_midi_event snd_seq snd_emu10k1 snd_rawmidi snd_pcm
> snd_timer snd_seq_device snd_ac97_codec snd_page_alloc snd_util_mem
> snd_hwdep snd soundcore hid usbcore aic7xxx sd_mod scsi_mod
>
>
> [7.2.] Processor information (from /proc/cpuinfo):
> processor : 0
> vendor_id : GenuineIntel
> cpu family : 6
> model : 8
> model name : Pentium III (Coppermine)
> stepping : 10
> cpu MHz : 999.661
> cache size : 256 KB
> fdiv_bug : no
> hlt_bug : no
> f00f_bug : no
> coma_bug : no
> fpu : yes
> fpu_exception : yes
> cpuid level : 2
> wp : yes
> flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
> mca cmov pat pse36 mmx fxsr sse
> bogomips : 1970.17
>
>
> [7.3.] Module information (from /proc/modules):
> snd_pcm_oss 53700 0 - Live 0xe0d30000
> agpgart 32328 0 - Live 0xe0cd1000
> nvidia 1706124 10 - Live 0xe0e98000
> vmnet 28016 4 - Live 0xe0c79000
> vmmon 70105 0 - Live 0xe0c88000
> nfs 159328 1 - Live 0xe0c9e000
> ide_cd 40836 0 - Live 0xe0c48000
> cdrom 35360 1 ide_cd, Live 0xe0c54000
> snd_mixer_oss 19264 1 snd_pcm_oss, Live 0xe0b6e000
> uhci_hcd 32624 0 - Live 0xe0c09000
> eeprom 7048 0 - Live 0xe0a8f000
> i2c_sensor 2880 1 eeprom, Live 0xe0a92000
> usb_storage 66816 0 - Live 0xe0c5e000
> i2c_viapro 5964 0 - Live 0xe0a85000
> i2c_core 25352 3 eeprom,i2c_sensor,i2c_viapro, Live 0xe0c01000
> binfmt_misc 10504 1 - Live 0xe0b63000
> parport_pc 28940 1 - Live 0xe0bf8000
> lp 10688 0 - Live 0xe0a6b000
> parport 44264 2 parport_pc,lp, Live 0xe0bec000
> nfsd 184832 8 - Live 0xe0c19000
> exportfs 6464 1 nfsd, Live 0xe0a7b000
> lockd 64560 3 nfs,nfsd, Live 0xe0b77000
> sunrpc 134184 6 nfs,nfsd,lockd, Live 0xe0b8a000
> capability 3748 0 - Live 0xe0860000
> commoncap 6464 1 capability, Live 0xe0a78000
> iptable_filter 2688 0 - Live 0xe0811000
> ip_tables 17888 1 iptable_filter, Live 0xe0a7f000
> 8139too 20928 0 - Live 0xe0a88000
> mii 5120 1 8139too, Live 0xe0a75000
> crc32 4320 1 8139too, Live 0xe0a72000
> ipv6 255136 16 - Live 0xe0bac000
> microcode 6688 0 - Live 0xe0a6f000
> reiserfs 240116 1 - Live 0xe0a96000
> nls_iso8859_1 3904 4 - Live 0xe080d000
> nls_cp437 5568 4 - Live 0xe0a05000
> vfat 15744 4 - Live 0xe0a3a000
> fat 45568 1 vfat, Live 0xe0a48000
> snd_seq_midi 8416 0 - Live 0xe0a01000
> snd_emu10k1_synth 7776 0 - Live 0xe09fe000
> snd_emux_synth 37856 1 snd_emu10k1_synth, Live 0xe0a25000
> snd_seq_virmidi 7488 1 snd_emux_synth, Live 0xe09fb000
> snd_seq_midi_emul 7968 1 snd_emux_synth, Live 0xe0958000
> snd_seq_oss 34816 0 - Live 0xe0a1b000
> snd_seq_midi_event 7680 3 snd_seq_midi,snd_seq_virmidi,snd_seq_oss, Live
> 0xe0930000
> snd_seq 55792 8
> snd_seq_midi,snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_oss,snd_seq_midi_event, Live 0xe0a0c000
> snd_emu10k1 70340 1 snd_emu10k1_synth, Live 0xe0945000
> snd_rawmidi 24864 3 snd_seq_midi,snd_seq_virmidi,snd_emu10k1, Live
> 0xe093d000
> snd_pcm 100612 2 snd_pcm_oss,snd_emu10k1, Live 0xe095b000
> snd_timer 25572 2 snd_seq,snd_pcm, Live 0xe0935000
> snd_seq_device 8040 7
> snd_seq_midi,snd_emu10k1_synth,snd_emux_synth,snd_seq_oss,snd_seq,snd_emu10k1,snd_rawmidi, Live 0xe088e000
> snd_ac97_codec 54884 1 snd_emu10k1, Live 0xe0851000
> snd_page_alloc 11812 2 snd_emu10k1,snd_pcm, Live 0xe0818000
> snd_util_mem 4448 2 snd_emux_synth,snd_emu10k1, Live 0xe0820000
> snd_hwdep 9440 1 snd_emu10k1, Live 0xe082d000
> snd 51876 16
> snd_pcm_oss,snd_mixer_oss,snd_seq_midi,snd_emux_synth,snd_seq_virmidi,snd_seq_oss,snd_seq_midi_event,snd_seq,snd_emu10k1,snd_rawmidi,snd_pcm,snd_timer,snd_seq_device,snd_ac97_codec,snd_util_mem,snd_hwdep, Live 0xe0862000
> soundcore 9088 1 snd, Live 0xe081c000
> hid 32960 0 - Live 0xe0823000
> usbcore 110428 5 uhci_hcd,usb_storage,hid, Live 0xe0872000
> aic7xxx 211116 6 - Live 0xe0891000
> sd_mod 15232 8 - Live 0xe0813000
> scsi_mod 118808 3 usb_storage,aic7xxx,sd_mod, Live 0xe0832000
>
>
> [7.4.] Loaded driver and hardware information (/proc/ioports,
> /proc/iomem)
> ioports:
> 0000-001f : dma1
> 0020-0021 : pic1
> 0040-005f : timer
> 0060-006f : keyboard
> 0070-0077 : rtc
> 0080-008f : dma page reg
> 00a0-00a1 : pic2
> 00c0-00df : dma2
> 00f0-00ff : fpu
> 0170-0177 : ide1
> 01f0-01f7 : ide0
> 0376-0376 : ide1
> 0378-037a : parport0
> 037b-037f : parport0
> 03c0-03df : vga+
> 03f6-03f6 : ide0
> 0cf8-0cff : PCI conf1
> 5000-5007 : viapro-smbus
> d000-d00f : 0000:00:07.1
> d000-d007 : ide0
> d008-d00f : ide1
> d400-d41f : 0000:00:07.2
> d400-d41f : uhci_hcd
> d800-d8ff : 0000:00:11.0
> dc00-dcff : 0000:00:12.0
> dc00-dcff : 8139too
> e000-e01f : 0000:00:13.0
> e000-e01f : EMU10K1
> e400-e407 : 0000:00:13.1
>
> iomem:
> 00000000-0009fbff : System RAM
> 0009fc00-0009ffff : reserved
> 000a0000-000bffff : Video RAM area
> 000d4000-000d93ff : Extension ROM
> 000f0000-000fffff : System ROM
> 00100000-1fffffff : System RAM
> 00100000-002ade57 : Kernel code
> 002ade58-00337eff : Kernel data
> d0000000-dfffffff : PCI Bus #01
> d0000000-d7ffffff : 0000:01:00.0
> d8000000-d807ffff : 0000:01:00.0
> e0000000-e7ffffff : 0000:00:00.0
> e8000000-e9ffffff : PCI Bus #01
> e8000000-e8ffffff : 0000:01:00.0
> eb000000-eb000fff : 0000:00:11.0
> eb000000-eb000fff : aic7xxx
> eb001000-eb0010ff : 0000:00:12.0
> eb001000-eb0010ff : 8139too
> ffff0000-ffffffff : reserved
>
>
>
>
> [7.5.] PCI information ('lspci -vvv' as root)
> 00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo
> PRO133x] (rev 82)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0
> Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
> Capabilities: [a0] AGP version 2.0
> Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
> Command: RQ=0 SBA- AGP+ 64bit- FW- Rate=x2
>
> 00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo
> MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: e8000000-e9ffffff
> Prefetchable memory behind bridge: d0000000-dfffffff
> BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C596 ISA [Mobile South]
> (rev 12)
> Subsystem: VIA Technologies, Inc. VT82C596/A/B PCI to ISA Bridge
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping+ SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:07.1 IDE interface: VIA Technologies, Inc.
> VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06)
> (prog-if 8a [Master SecP PriP])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Region 4: I/O ports at d000 [size=16]
>
> 00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 08) (prog-if 00
> [UHCI])
> Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, cache line size 08
> Interrupt: pin D routed to IRQ 10
> Region 4: I/O ports at d400 [size=32]
>
> 00:07.3 Host bridge: VIA Technologies, Inc. VT82C596 Power Management
> (rev 20)
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>
> 00:11.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
> Subsystem: Adaptec 29160 Ultra160 SCSI Controller
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (10000ns min, 6250ns max), cache line size 08
> Interrupt: pin A routed to IRQ 5
> BIST result: 00
> Region 0: I/O ports at d800 [disabled] [size=256]
> Region 1: Memory at eb000000 (64-bit, non-prefetchable)
> [size=4K]
> Expansion ROM at <unassigned> [disabled] [size=128K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:12.0 Ethernet controller: Accton Technology Corporation SMC2-1211TX
> (rev 10)
> Subsystem: Accton Technology Corporation: Unknown device 9211
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (8000ns min, 16000ns max)
> Interrupt: pin A routed to IRQ 9
> Region 0: I/O ports at dc00 [size=256]
> Region 1: Memory at eb001000 (32-bit, non-prefetchable)
> [size=256]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
> PME(D0-,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
>
> 00:13.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev
> 07)
> Subsystem: Creative Labs SB Live! 5.1 Model SB0100
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (500ns min, 5000ns max)
> Interrupt: pin A routed to IRQ 10
> Region 0: I/O ports at e000 [size=32]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:13.1 Input device controller: Creative Labs SB Live! MIDI/Game Port
> (rev 07)
> Subsystem: Creative Labs Gameport Joystick
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Region 0: I/O ports at e400 [size=8]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 01:00.0 VGA compatible controller: nVidia Corporation NV25 [GeForce4 Ti
> 4200] (rev a3) (prog-if 00 [VGA])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 248 (1250ns min, 250ns max)
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at e8000000 (32-bit, non-prefetchable)
> [size=16M]
> Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M]
> Region 2: Memory at d8000000 (32-bit, prefetchable) [size=512K]
> Expansion ROM at <unassigned> [disabled] [size=128K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [44] AGP version 2.0
> Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2,x4
> Command: RQ=31 SBA- AGP+ 64bit- FW- Rate=x2
>
>
>
> [7.6.] SCSI information (from /proc/scsi/scsi)
> Attached devices:
> Host: scsi0 Channel: 00 Id: 00 Lun: 00
> Vendor: WDIGTL Model: ENTERPRISE Rev: 1.61
> Type: Direct-Access ANSI SCSI revision: 02
> Host: scsi0 Channel: 00 Id: 01 Lun: 00
> Vendor: PLEXTOR Model: CD-ROM PX-20TS Rev: 1.00
> Type: CD-ROM ANSI SCSI revision: 02
> Host: scsi0 Channel: 00 Id: 04 Lun: 00
> Vendor: PLEXTOR Model: CD-R PX-W1210S Rev: 1.06
> Type: CD-ROM ANSI SCSI revision: 02
> Host: scsi0 Channel: 00 Id: 06 Lun: 00
> Vendor: IBM Model: DDYS-T36950N Rev: S96H
> Type: Direct-Access ANSI SCSI revision: 03
>
>
>
>
>
> --
> Jean-Yves Simon <lethalwp@xxxxxxxxxx>
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
-andmike
--
Michael Anderson
andmike@xxxxxxxxxx

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/