Re: Fixes for nforce2 hard lockup, apic, io-apic, udma133 covered

From: Jesse Allen
Date: Thu Dec 11 2003 - 12:25:38 EST

On Thu, Dec 11, 2003 at 06:04:54PM +0100, Maciej W. Rozycki wrote:
> On Thu, 11 Dec 2003, Josh McKinney wrote:
>
> > Should I try it with just the acpi fixes sent by Maciej or are these
> > just general fixes?
>
> They should make (at least some of) the reported problems go away,
> superseding the respective workarounds.
>

As far as I can tell, your patch _alone_ doesn't prevent the lockup, fix the timer, or nmi_watchdog. I have attached a dmesg of my current running kernel that includes Ross' io_apic patch, the disconnect quirk patch, your acpi patch, and other minor patches. ACPI and APIC debugging are on.


Linux version 2.6.0-test11 (jesse@tesore) (gcc version 3.3.2) #2 Thu Dec 11 09:45:15 MST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS)
BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
255MB LOWMEM available.
On node 0 totalpages: 65520
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61424 pages, LIFO batch:14
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 Nvidia ) @ 0x000f6f60
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3000
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3040
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff7880
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:10 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, IRQ 0-23
ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1] trigger[0x3])
ACPI: INT_SRC_OVR (bus[0] irq[0xe] global_irq[0xe] polarity[0x1] trigger[0x1])
ACPI: INT_SRC_OVR (bus[0] irq[0xf] global_irq[0xf] polarity[0x1] trigger[0x1])
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Building zonelist for node : 0
Kernel command line: BOOT_IMAGE=Linux-2.6 ro root=301
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 1913.621 MHz processor.
Console: colour VGA+ 80x25
Memory: 256144k/262080k available (1611k kernel code, 5212k reserved, 693k data, 128k init, 0k highmem)
Calibrating delay loop... 3784.70 BogoMIPS
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 2600+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
..TIMER: Is timer irq0 connected to IOAPIC Pin0? ...
IOAPIC[0]: Set PCI routing entry (2-0 -> 0x31 -> IRQ 0 Mode:0 Active:0)
..TIMER: works OK on apic pin0 irq0
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 001 01 0 0 0 0 0 1 1 31
01 001 01 0 0 0 0 0 1 1 39
02 000 00 0 0 0 0 0 0 0 00
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 1 1 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2-> 0:0
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1912.0861 MHz.
..... host bus clock speed is 332.0671 MHz.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb590, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20031002
tbxface-0117 [03] acpi_load_tables : ACPI Tables successfully acquired
Parsing all Control Methods:........................................................................................................................................................................................................................................................................................
Table [DSDT](id F004) - 761 Objects with 78 Devices 280 Methods 30 Regions
ACPI Namespace successfully loaded at root c0378d3c
IOAPIC[0]: Set PCI routing entry (2-9 -> 0x71 -> IRQ 9 Mode:1 Active:0)
evxfevnt-0093 [04] acpi_enable : Transition to ACPI mode successful
evgpeblk-0748 [06] ev_create_gpe_block : GPE 00 to 31 [_GPE] 4 regs at 0000000000004020 on int 9
evgpeblk-0748 [06] ev_create_gpe_block : GPE 32 to 95 [_GPE] 8 regs at 00000000000044A0 on int 9
Completing Region/Field/Buffer/Package initialization:.................................................................................................
Initialized 30/30 Regions 9/9 Fields 31/31 Buffers 27/27 Packages (769 nodes)
Executing all Device _STA and_INI methods:...............................................................................
79 Devices found containing: 79 _STA, 2 _INI methods
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16)
ACPI: PCI Interrupt Link [APC2] (IRQs 17)
ACPI: PCI Interrupt Link [APC3] (IRQs *18)
ACPI: PCI Interrupt Link [APC4] (IRQs *19)
ACPI: PCI Interrupt Link [APC5] (IRQs 16)
pci_link-0262 [40] acpi_pci_link_get_curr: No IRQ resource found
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22)
pci_link-0262 [42] acpi_pci_link_get_curr: No IRQ resource found
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22)
pci_link-0262 [44] acpi_pci_link_get_curr: No IRQ resource found
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22)
pci_link-0262 [47] acpi_pci_link_get_curr: No IRQ resource found
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCS] (IRQs *23)
pci_link-0262 [52] acpi_pci_link_get_curr: No IRQ resource found
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCS] enabled at IRQ 23
IOAPIC[0]: Set PCI routing entry (2-23 -> 0xa9 -> IRQ 23 Mode:1 Active:0)
00:00:01[A] -> 2-23 -> IRQ 23
Pin 2-23 already programmed
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
IOAPIC[0]: Set PCI routing entry (2-20 -> 0xb1 -> IRQ 20 Mode:1 Active:0)
00:00:02[A] -> 2-20 -> IRQ 20
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 22
IOAPIC[0]: Set PCI routing entry (2-22 -> 0xb9 -> IRQ 22 Mode:1 Active:0)
00:00:02[B] -> 2-22 -> IRQ 22
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
IOAPIC[0]: Set PCI routing entry (2-21 -> 0xc1 -> IRQ 21 Mode:1 Active:0)
00:00:02[C] -> 2-21 -> IRQ 21
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 20
Pin 2-20 already programmed
ACPI: PCI Interrupt Link [APCI] enabled at IRQ 22
Pin 2-22 already programmed
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21
Pin 2-21 already programmed
ACPI: PCI Interrupt Link [APCK] enabled at IRQ 20
Pin 2-20 already programmed
ACPI: PCI Interrupt Link [APCM] enabled at IRQ 22
Pin 2-22 already programmed
ACPI: PCI Interrupt Link [APCZ] enabled at IRQ 21
Pin 2-21 already programmed
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xc9 -> IRQ 16 Mode:1 Active:0)
00:01:08[A] -> 2-16 -> IRQ 16
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xd1 -> IRQ 17 Mode:1 Active:0)
00:01:08[B] -> 2-17 -> IRQ 17
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xd9 -> IRQ 18 Mode:1 Active:0)
00:01:08[C] -> 2-18 -> IRQ 18
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xe1 -> IRQ 19 Mode:1 Active:0)
00:01:08[D] -> 2-19 -> IRQ 19
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-19 already programmed
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Machine check exception polling timer started.
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FAN] (on)
ACPI: Processor [CPU0] (supports C1)
ACPI: Thermal Zone [THRM] (38 C)
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.12
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: WDC WD200BB-00DEA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: MATSHITA CR-585, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63, UDMA(100)
hda: hda1 hda2 hda3
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
mice: PS/2 mouse device common for all mice
input: PC Speaker
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Translated Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 1
NET: Registered protocol family 17
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hda1) for (hda1)
Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 128k freed
Adding 377516k swap on /dev/hda2. Priority:-1 extents:1
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hda3) for (hda3)
Using r5 hash to sort names
Linux agpgart interface v0.100 (c) Dave Jones
8139too Fast Ethernet driver 0.9.27
eth0: RealTek RTL8139 at 0xd09a1000, 00:40:c7:77:0a:d5, IRQ 18
eth0: Identified 8139 chip type 'RTL-8139 rev K'
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
agpgart: Detected NVIDIA nForce2 chipset
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 64M @ 0xe8000000
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0: clocking to 47451
/home/jesse/linux/drivers/usb/core/usb.c: registered new driver hub
ohci_hcd: 2003 Oct 13 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 20, pci mem d0a17000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd 0000:00:02.1: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 22, pci mem d0a20000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ehci_hcd 0000:00:02.2: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 21, pci mem d0a2e000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-13
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5100
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/