[2.6.1rc1] usb memorystick doesnt work / 2.6.0-test9 does work

From: Florian Lohoff
Date: Tue Jan 06 2004 - 13:08:55 EST



Hi,
i found by accident that my memorystick does work anymore with 2.6.1rc1.
Last kernel i tried it works with is -test9. -test11, 2.6.0 seem all not
work.

It gets detected as SCSI Disk correctly:

Initializing USB Mass Storage driver...
scsi1 : SCSI emulation for USB Mass Storage devices
Vendor: Model: Floppy-on-stick Rev: 1.89
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 5
drivers/usb/core/usb.c: registered new driver usb-storage
USB Mass Storage support registered.
SCSI device sda: 255744 512-byte hdwr sectors (131 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
sda: sda1
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0

A mount like mount -t vfat /dev/sda1 /mnt/flash - This stick

SCSI error : <1 0 0 0> return code = 0x8000000
Current sda: sense key No Sense
end_request: I/O error, dev sda, sector 32
FAT: unable to read boot sector

/proc/bus/devices

T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.0 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:1d.2
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms

T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.0 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:1d.1
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms

T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.0 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:1d.0
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms

T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=046d ProdID=c00c Rev= 6.20
S: Manufacturer=Logitech
S: Product=USB Mouse
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=hid
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=10ms

T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0ea0 ProdID=6828 Rev= 1.10
S: Manufacturer=USB
S: Product=Flash Disk
S: SerialNumber=C49514A83F34AFD6
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 2 Ivl=255ms

T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.0 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:1d.7
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms


dmesg:

PIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0xff] polarity[0x1] trigger[0x1] lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 1
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, IRQ 0-23
ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x1] trigger[0x1])
ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1] trigger[0x3])
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Building zonelist for node : 0
Kernel command line: auto BOOT_IMAGE=Linux ro root=306
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 2392.592 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Memory: 514604k/523776k available (1968k kernel code, 8356k reserved, 827k data, 144k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4718.59 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU#0: Thermal monitoring enabled
CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-0, 1-16, 1-17, 1-18, 1-19, 1-20, 1-21, 1-22, 1-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
number of MP IRQ sources: 15.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00000000
....... : arbitration: 00
.... register #03: 00000001
....... : Boot DT : 1
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 1 1 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2391.0998 MHz.
..... host bus clock speed is 132.0888 MHz.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd987, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20031002
tbxface-0117 [03] acpi_load_tables : ACPI Tables successfully acquired
Parsing all Control Methods:.....................................................................................................
Table [DSDT](id F004) - 410 Objects with 51 Devices 101 Methods 13 Regions
ACPI Namespace successfully loaded at root c03f813c
IOAPIC[0]: Set PCI routing entry (1-9 -> 0x71 -> IRQ 9 Mode:1 Active:0)
evxfevnt-0093 [04] acpi_enable : Transition to ACPI mode successful
evgpeblk-0748 [06] ev_create_gpe_block : GPE 00 to 31 [_GPE] 4 regs at 000000000000F028 on int 9
Completing Region/Field/Buffer/Package initialization:..........................................................................
Initialized 13/13 Regions 6/6 Fields 33/33 Buffers 22/22 Packages (418 nodes)
Executing all Device _STA and_INI methods:....................................................
52 Devices found containing: 52 _STA, 2 _INI methods
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIH._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
IOAPIC[0]: Set PCI routing entry (1-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1)
00:00:02[A] -> 1-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (1-17 -> 0xb1 -> IRQ 17 Mode:1 Active:1)
00:00:02[B] -> 1-17 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (1-18 -> 0xb9 -> IRQ 18 Mode:1 Active:1)
00:00:1f[A] -> 1-18 -> IRQ 18
Pin 1-17 already programmed
Pin 1-16 already programmed
IOAPIC[0]: Set PCI routing entry (1-19 -> 0xc1 -> IRQ 19 Mode:1 Active:1)
00:00:1d[B] -> 1-19 -> IRQ 19
Pin 1-18 already programmed
IOAPIC[0]: Set PCI routing entry (1-23 -> 0xc9 -> IRQ 23 Mode:1 Active:1)
00:00:1d[D] -> 1-23 -> IRQ 23
Pin 1-16 already programmed
Pin 1-17 already programmed
Pin 1-17 already programmed
Pin 1-18 already programmed
Pin 1-19 already programmed
IOAPIC[0]: Set PCI routing entry (1-20 -> 0xd1 -> IRQ 20 Mode:1 Active:1)
00:02:05[D] -> 1-20 -> IRQ 20
Pin 1-18 already programmed
Pin 1-19 already programmed
Pin 1-20 already programmed
IOAPIC[0]: Set PCI routing entry (1-21 -> 0xd9 -> IRQ 21 Mode:1 Active:1)
00:02:07[D] -> 1-21 -> IRQ 21
Pin 1-20 already programmed
Pin 1-19 already programmed
Pin 1-20 already programmed
Pin 1-21 already programmed
IOAPIC[0]: Set PCI routing entry (1-22 -> 0xe1 -> IRQ 22 Mode:1 Active:1)
00:02:09[D] -> 1-22 -> IRQ 22
Pin 1-20 already programmed
Pin 1-21 already programmed
Pin 1-22 already programmed
Pin 1-23 already programmed
Pin 1-21 already programmed
Pin 1-22 already programmed
Pin 1-23 already programmed
Pin 1-16 already programmed
Pin 1-22 already programmed
Pin 1-23 already programmed
Pin 1-16 already programmed
Pin 1-17 already programmed
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
SBF: Simple Boot Flag extension found and enabled.
SBF: Setting boot flags 0x1
Machine check exception polling timer started.
cpufreq: P4/Xeon(TM) CPU On-Demand Clock Modulation available
speedstep-smi: signature:0x00008680, command:0x0000e6f5, event:0x00000000, perf_level:0x47534943.
IA-32 Microcode Update Driver: v1.13 <tigran@xxxxxxxxxxx>
Initializing Cryptographic API
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1)
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
hw_random: RNG not detected
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 845G Chipset.
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 64M @ 0xe0000000
[drm] Initialized mga 3.1.0 20021029 on minor 0
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2800-0x2807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x2808-0x280f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 2F040L0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: Maxtor 6Y120L0, ATA DISK drive
hdd: JLMS XJ-HD166S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: hda1 < hda5 hda6 hda7 hda8 hda9 hda10 >
hdc: max request size: 128KiB
hdc: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(33)
hdc: unknown partition table
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@xxxxxxxxxxxxxxx>
All bugs added by David S. Miller <davem@xxxxxxxxxx>
BIOS EDD facility v0.10 2003-Oct-11, 1 devices found
Please report your BIOS at http://domsch.com/linux/edd30/results.html
PM: Reading pmdisk image.
PM: Resume from disk failed.
ACPI: (supports S0 S1 S3 S4 S5)
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 144k freed
Adding 505976k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda6, internal journal
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@xxxxxxxxxxxxx> and others
eth0: OEM i82557/i82558 10/100 Ethernet, 00:30:05:3D:B1:E9, IRQ 20.
Board assembly 000000-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
ohci1394: $Rev: 1087 $ Ben Collins <bcollins@xxxxxxxxxx>
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[d1005000-d10057ff] Max Packet=[2048]
SCSI subsystem initialized
device-mapper: 4.0.0-ioctl (2003-06-04) initialised: dm@xxxxxxxxxxxxxx
ieee1394: Node added: ID:BUS[0-00:1023] GUID[0004830252004f0f]
ieee1394: Host added: ID:BUS[0-01:1023] GUID[0001b7000001515b]
sbp2: $Rev: 1082 $ Ben Collins <bcollins@xxxxxxxxxx>
scsi0 : SCSI emulation for IEEE-1394 SBP-2 Devices
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
ieee1394: sbp2: Logged into SBP-2 device
ieee1394: sbp2: Node 0-00:1023: Max speed [S400] - Max payload [2048]
Vendor: SONY Model: DVD RW DRU-500A Rev: 2.0e
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 5
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 23, pci mem e088a000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-13
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 16, io base 00001000
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 19, io base 00001400
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 18, io base 00001800
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 1-0:1.0: new USB device on port 2, assigned address 2
Disabled Privacy Extensions on device c0380f60(lo)
hub 2-0:1.0: new USB device on port 1, assigned address 2
ip_tables: (C) 2000-2002 Netfilter core team

Flo
--
Florian Lohoff flo@xxxxxxxxxx +49-171-2280134
Heisenberg may have been here.

Attachment: pgp00000.pgp
Description: PGP signature