via-rhine crashes, 2.6.5-rc2-mm1
From: Ross Vandegrift
Date: Tue Mar 23 2004 - 23:44:37 EST
Hello everyone,
I'm using kernel 2.6.5-rc2-mm1 on a motherboard with a VIA Rhine
network adaptor and am getting crashes at boot. The chipset is KT400,
with VT6102 [Rhine-II] (rev 74) network adaptor. I'm booting the
kernel with parameters "noapic" and "acpi=off". Preemption is disabled.
I get stack dumps when traffic is sent out, and every few
minutes "Disabline IRQ #11" messages. 2.4.23+lowlatency works without a
hitch.
Call traces follow:
eth0: VIA VT6102 Rhine-II at 0xcc00, 00:0a:e6:d1:b8:9f, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1.
irq 11: nobody cared!
Call Trace:
[<c01085d4>] __report_bad_irq+0x24/0x80
[<c01086b1>] note_interrupt+0x61/0x90
[<c0108939>] do_IRQ+0x149/0x170
[<c0260c70>] common_interrupt+0x18/0x20
[<c011eeb0>] __do_softirq+0x30/0x80
[<c010901f>] do_softirq+0x4f/0x60
=======================
[<c0108921>] do_IRQ+0x131/0x170
[<c0256bc1>] fib_magic+0xf1/0x100
[<c0260c70>] common_interrupt+0x18/0x20
[<c0108d6f>] setup_irq+0x6f/0xa0
[<e09d7cc0>] via_rhine_interrupt+0x0/0x1b0 [via_rhine]
[<c0108a3d>] request_irq+0x9d/0xd0
[<e09d76c9>] via_rhine_open+0x49/0x150 [via_rhine]
[<c021cc58>] dev_open+0xc8/0x100
[<c021dfe1>] dev_change_flags+0x101/0x120
[<c02503d7>] devinet_ioctl+0x2b7/0x690
[<c0252543>] inet_ioctl+0xa3/0xe0
[<c0215fda>] sock_ioctl+0xaa/0x220
[<c015a76f>] sys_ioctl+0xcf/0x220
[<c026028b>] syscall_call+0x7/0xb
handlers:
[<e09d7cc0>] (via_rhine_interrupt+0x0/0x1b0 [via_rhine])
Disabling IRQ #11
eth0: Setting full-duplex based on MII #1 link partner capability of 41e1.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0003, PHY status 786d, resetting...
eth0: Setting full-duplex based on MII #1 link partner capability of 41e1.
irq 11: nobody cared!
Call Trace:
[<c01085d4>] __report_bad_irq+0x24/0x80
[<c01e0500>] vt_console_print+0x0/0x2e0
[<c01086b1>] note_interrupt+0x61/0x90
[<c011bcc8>] __call_console_drivers+0x48/0x50
[<c0108939>] do_IRQ+0x149/0x170
[<c0260c70>] common_interrupt+0x18/0x20
[<c0108767>] enable_irq+0x37/0xc0
[<e09d756b>] init_registers+0xeb/0x100 [via_rhine]
[<e09d7a53>] via_rhine_tx_timeout+0xa3/0x100 [via_rhine]
[<c0225c60>] dev_watchdog+0x0/0xa0
[<c0225ced>] dev_watchdog+0x8d/0xa0
[<c0122a2e>] run_timer_softirq+0xae/0x160
[<c011eefc>] __do_softirq+0x7c/0x80
[<c010901f>] do_softirq+0x4f/0x60
=======================
[<c0108921>] do_IRQ+0x131/0x170
[<c0105030>] default_idle+0x0/0x30
[<c0260c70>] common_interrupt+0x18/0x20
[<c0105030>] default_idle+0x0/0x30
[<c0105054>] default_idle+0x24/0x30
[<c01050d0>] cpu_idle+0x30/0x40
[<c02e0717>] start_kernel+0x137/0x160
[<c02e0470>] unknown_bootoption+0x0/0x130
handlers:
[<e09d7cc0>] (via_rhine_interrupt+0x0/0x1b0 [via_rhine])
Disabling IRQ #11
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0003, PHY status 786d, resetting...
eth0: Setting full-duplex based on MII #1 link partner capability of 41e1.
irq 11: nobody cared!
Call Trace:
[<c01085d4>] __report_bad_irq+0x24/0x80
[<c01086b1>] note_interrupt+0x61/0x90
[<c01189f1>] __wake_up_common+0x31/0x60
[<c0108939>] do_IRQ+0x149/0x170
[<c0260c70>] common_interrupt+0x18/0x20
[<c0108767>] enable_irq+0x37/0xc0
[<e09d756b>] init_registers+0xeb/0x100 [via_rhine]
[<e09d7a53>] via_rhine_tx_timeout+0xa3/0x100 [via_rhine]
[<c0225c60>] dev_watchdog+0x0/0xa0
[<c0225ced>] dev_watchdog+0x8d/0xa0
[<c0122a2e>] run_timer_softirq+0xae/0x160
[<c011eefc>] __do_softirq+0x7c/0x80
[<c010901f>] do_softirq+0x4f/0x60
=======================
[<c0108921>] do_IRQ+0x131/0x170
[<c0105030>] default_idle+0x0/0x30
[<c0260c70>] common_interrupt+0x18/0x20
[<c0105030>] default_idle+0x0/0x30
[<c0105054>] default_idle+0x24/0x30
[<c01050d0>] cpu_idle+0x30/0x40
[<c02e0717>] start_kernel+0x137/0x160
[<c02e0470>] unknown_bootoption+0x0/0x130
handlers:
[<e09d7cc0>] (via_rhine_interrupt+0x0/0x1b0 [via_rhine])
Disabling IRQ #11
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0003, PHY status 786d, resetting...
eth0: Setting full-duplex based on MII #1 link partner capability of 41e1.
irq 11: nobody cared!
Call Trace:
[<c01085d4>] __report_bad_irq+0x24/0x80
[<c01086b1>] note_interrupt+0x61/0x90
[<c01189f1>] __wake_up_common+0x31/0x60
[<c0108939>] do_IRQ+0x149/0x170
[<c0260c70>] common_interrupt+0x18/0x20
[<c0108767>] enable_irq+0x37/0xc0
[<e09d756b>] init_registers+0xeb/0x100 [via_rhine]
[<e09d7a53>] via_rhine_tx_timeout+0xa3/0x100 [via_rhine]
[<c0225c60>] dev_watchdog+0x0/0xa0
[<c0225ced>] dev_watchdog+0x8d/0xa0
[<c0122a2e>] run_timer_softirq+0xae/0x160
[<c011eefc>] __do_softirq+0x7c/0x80
[<c010901f>] do_softirq+0x4f/0x60
=======================
[<c0108921>] do_IRQ+0x131/0x170
[<c0105030>] default_idle+0x0/0x30
[<c0260c70>] common_interrupt+0x18/0x20
[<c0105030>] default_idle+0x0/0x30
[<c0105054>] default_idle+0x24/0x30
[<c01050d0>] cpu_idle+0x30/0x40
[<c02e0717>] start_kernel+0x137/0x160
[<c02e0470>] unknown_bootoption+0x0/0x130
handlers:
[<e09d7cc0>] (via_rhine_interrupt+0x0/0x1b0 [via_rhine])
Disabling IRQ #11
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0003, PHY status 786d, resetting...
eth0: Setting full-duplex based on MII #1 link partner capability of 41e1.
irq 11: nobody cared!
Call Trace:
[<c01085d4>] __report_bad_irq+0x24/0x80
[<c01086b1>] note_interrupt+0x61/0x90
[<c01189f1>] __wake_up_common+0x31/0x60
[<c0108939>] do_IRQ+0x149/0x170
[<c0260c70>] common_interrupt+0x18/0x20
[<c0108767>] enable_irq+0x37/0xc0
[<e09d756b>] init_registers+0xeb/0x100 [via_rhine]
[<e09d7a53>] via_rhine_tx_timeout+0xa3/0x100 [via_rhine]
[<c0225c60>] dev_watchdog+0x0/0xa0
[<c0225ced>] dev_watchdog+0x8d/0xa0
[<c0122a2e>] run_timer_softirq+0xae/0x160
[<c011eefc>] __do_softirq+0x7c/0x80
[<c010901f>] do_softirq+0x4f/0x60
=======================
[<c0108921>] do_IRQ+0x131/0x170
[<c0105030>] default_idle+0x0/0x30
[<c0260c70>] common_interrupt+0x18/0x20
[<c0105030>] default_idle+0x0/0x30
[<c0105054>] default_idle+0x24/0x30
[<c01050d0>] cpu_idle+0x30/0x40
[<c02e0717>] start_kernel+0x137/0x160
[<c02e0470>] unknown_bootoption+0x0/0x130
handlers:
[<e09d7cc0>] (via_rhine_interrupt+0x0/0x1b0 [via_rhine])
Disabling IRQ #11
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0003, PHY status 786d, resetting...
eth0: Setting full-duplex based on MII #1 link partner capability of 41e1.
irq 11: nobody cared!
Call Trace:
[<c01085d4>] __report_bad_irq+0x24/0x80
[<c01086b1>] note_interrupt+0x61/0x90
[<c0108580>] handle_IRQ_event+0x30/0x60
[<c0108939>] do_IRQ+0x149/0x170
[<c0260c70>] common_interrupt+0x18/0x20
[<c0108570>] handle_IRQ_event+0x20/0x60
[<c01088ba>] do_IRQ+0xca/0x170
=======================
[<c0260c70>] common_interrupt+0x18/0x20
[<c0108767>] enable_irq+0x37/0xc0
[<e09d756b>] init_registers+0xeb/0x100 [via_rhine]
[<e09d7a53>] via_rhine_tx_timeout+0xa3/0x100 [via_rhine]
[<c0225c60>] dev_watchdog+0x0/0xa0
[<c0225ced>] dev_watchdog+0x8d/0xa0
[<c0122a2e>] run_timer_softirq+0xae/0x160
[<c011eefc>] __do_softirq+0x7c/0x80
[<c010901f>] do_softirq+0x4f/0x60
=======================
[<c0108921>] do_IRQ+0x131/0x170
[<c0105030>] default_idle+0x0/0x30
[<c0260c70>] common_interrupt+0x18/0x20
[<c0105030>] default_idle+0x0/0x30
[<c0105054>] default_idle+0x24/0x30
[<c01050d0>] cpu_idle+0x30/0x40
[<c02e0717>] start_kernel+0x137/0x160
[<c02e0470>] unknown_bootoption+0x0/0x130
handlers:
[<e09d7cc0>] (via_rhine_interrupt+0x0/0x1b0 [via_rhine])
Disabling IRQ #11
--
Ross Vandegrift
ross@xxxxxxxxxxxxxxxx
A Pope has a Water Cannon. It is a Water Cannon.
He fires Holy-Water from it. It is a Holy-Water Cannon.
He Blesses it. It is a Holy Holy-Water Cannon.
He Blesses the Hell out of it. It is a Wholly Holy Holy-Water Cannon.
He has it pierced. It is a Holey Wholly Holy Holy-Water Cannon.
He makes it official. It is a Canon Holey Wholly Holy Holy-Water Cannon.
Batman and Robin arrive. He shoots them.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/