[PATCH] ppc64: properly build list of legacy serial ports from OFtree
From: Benjamin Herrenschmidt
Date: Fri Oct 22 2004 - 21:50:27 EST
Hi !
This patch applies on top of "8250: Let arch provide the list of
leagacy ports dynamically".
It adds a generic ppc64 routine for use by platforms that will build
the list of 8250 ports with proper IO address and irq numbers based
on the OF device-tree, and will also provide the physical address
where the primary one is, for use with the early boot console stuff.
Finally, it adds use of this new routine to the pSeries platform,
replacing the old one that was there. It will be also used by the
new eval board platform that is coming soon.
Signed-off-by: Benjamin Herrenschmidt <benh@xxxxxxxxxxxxxxxxxxx>
This patch adds a ppc64 implementation of the routine providing
the list of default 8250 serial ports. It provides a empty list
by default unless the platform code fills it, and it provides
a generic function for user by Open Firmware based machines which
fills the list based on serial ports found in the OF device-tree.
It depends on the previous patch adding the generic support for
this to the 8250 driver.
Signed-off-by: Benjamin Herrenschmidt <benh@xxxxxxxxxxxxxxxxxxx>
Index: linux-work/arch/ppc64/kernel/setup.c
===================================================================
--- linux-work.orig/arch/ppc64/kernel/setup.c 2004-10-17 12:07:07.000000000 +1000
+++ linux-work/arch/ppc64/kernel/setup.c 2004-10-23 12:30:57.502821472 +1000
@@ -30,6 +30,8 @@
#include <linux/notifier.h>
#include <linux/cpu.h>
#include <linux/unistd.h>
+#include <linux/serial.h>
+#include <linux/8250.h>
#include <asm/io.h>
#include <asm/prom.h>
#include <asm/processor.h>
@@ -51,6 +53,7 @@
#include <asm/system.h>
#include <asm/rtas.h>
#include <asm/iommu.h>
+#include <asm/serial.h>
#ifdef DEBUG
#define DBG(fmt...) udbg_printf(fmt)
@@ -1106,6 +1109,185 @@
__setup("decr_overclock_proc0=", set_decr_overclock_proc0 );
__setup("decr_overclock=", set_decr_overclock );
+#ifndef CONFIG_PPC_ISERIES
+/*
+ * This function can be used by platforms to "find" legacy serial ports.
+ * It works for "serial" nodes under an "isa" node, and will try to
+ * respect the "ibm,aix-loc" property if any. It works with up to 8
+ * ports.
+ */
+
+#define MAX_LEGACY_SERIAL_PORTS 8
+static struct old_serial_port old_serial_ports[MAX_LEGACY_SERIAL_PORTS];
+static unsigned int old_serial_count;
+
+void __init generic_find_legacy_serial_ports(unsigned int *default_speed)
+{
+ struct device_node *np;
+ u32 *sizeprop;
+
+ struct isa_reg_property {
+ u32 space;
+ u32 address;
+ u32 size;
+ };
+ struct pci_reg_property {
+ struct pci_address addr;
+ u32 size_hi;
+ u32 size_lo;
+ };
+
+ DBG(" -> generic_find_legacy_serial_port()\n");
+
+ naca->serialPortAddr = 0;
+ if (default_speed)
+ *default_speed = 0;
+
+ np = of_find_node_by_path("/");
+ if (!np)
+ return;
+
+ /* First fill our array */
+ for (np = NULL; (np = of_find_node_by_type(np, "serial"));) {
+ struct device_node *isa, *pci;
+ struct isa_reg_property *reg;
+ unsigned long phys_size, addr_size, io_base;
+ u32 *rangesp;
+ u32 *interrupts, *clk, *spd;
+ char *typep;
+ int index, rlen, rentsize;
+
+ /* Ok, first check if it's under an "isa" parent */
+ isa = of_get_parent(np);
+ if (!isa || strcmp(isa->name, "isa")) {
+ DBG("%s: no isa parent found\n", np->full_name);
+ continue;
+ }
+
+ /* Now look for an "ibm,aix-loc" property that gives us ordering
+ * if any...
+ */
+ typep = (char *)get_property(np, "ibm,aix-loc", NULL);
+
+ /* Get the ISA port number */
+ reg = (struct isa_reg_property *)get_property(np, "reg", NULL);
+ if (reg == NULL)
+ goto next_port;
+ /* We assume the interrupt number isn't translated ... */
+ interrupts = (u32 *)get_property(np, "interrupts", NULL);
+ /* get clock freq. if present */
+ clk = (u32 *)get_property(np, "clock-frequency", NULL);
+ /* get default speed if present */
+ spd = (u32 *)get_property(np, "current-speed", NULL);
+ /* Default to locate at end of array */
+ index = old_serial_count; /* end of the array by default */
+
+ /* If we have a location index, then use it */
+ if (typep && *typep == 'S') {
+ index = simple_strtol(typep+1, NULL, 0) - 1;
+ /* if index is out of range, use end of array instead */
+ if (index >= MAX_LEGACY_SERIAL_PORTS)
+ index = old_serial_count;
+ /* if our index is still out of range, that mean that
+ * array is full, we could scan for a free slot but that
+ * make little sense to bother, just skip the port
+ */
+ if (index >= MAX_LEGACY_SERIAL_PORTS)
+ goto next_port;
+ if (index >= old_serial_count)
+ old_serial_count = index + 1;
+ /* Check if there is a port who already claimed our slot */
+ if (old_serial_ports[index].port != 0) {
+ /* if we still have some room, move it, else override */
+ if (old_serial_count < MAX_LEGACY_SERIAL_PORTS) {
+ DBG("Moved legacy port %d -> %d\n", index,
+ old_serial_count);
+ old_serial_ports[old_serial_count++] =
+ old_serial_ports[index];
+ } else {
+ DBG("Replacing legacy port %d\n", index);
+ }
+ }
+ }
+ if (index >= MAX_LEGACY_SERIAL_PORTS)
+ goto next_port;
+ if (index >= old_serial_count)
+ old_serial_count = index + 1;
+
+ /* Now fill the entry */
+ memset(&old_serial_ports[index], 0, sizeof(struct old_serial_port));
+ old_serial_ports[index].uart = 0;
+ old_serial_ports[index].baud_base = clk ? (*clk / 16) : BASE_BAUD;
+ old_serial_ports[index].port = reg->address;
+ old_serial_ports[index].irq = interrupts ? interrupts[0] : 0;
+ old_serial_ports[index].flags = ASYNC_BOOT_AUTOCONF;
+
+ DBG("Added legacy port, index: %d, port: %x, irq: %d, clk: %d\n",
+ index,
+ old_serial_ports[index].port,
+ old_serial_ports[index].irq,
+ old_serial_ports[index].baud_base * 16);
+
+ /* Get phys address of IO reg for port 1 */
+ if (index != 0)
+ goto next_port;
+
+ pci = of_get_parent(isa);
+ if (!pci) {
+ DBG("%s: no pci parent found\n", np->full_name);
+ goto next_port;
+ }
+
+ rangesp = (u32 *)get_property(pci, "ranges", &rlen);
+ if (rangesp == NULL) {
+ of_node_put(pci);
+ goto next_port;
+ }
+ rlen /= 4;
+
+ /* we need the #size-cells of the PCI bridge node itself */
+ phys_size = 1;
+ sizeprop = (u32 *)get_property(pci, "#size-cells", NULL);
+ if (sizeprop != NULL)
+ phys_size = *sizeprop;
+ /* we need the parent #addr-cells */
+ addr_size = prom_n_addr_cells(pci);
+ rentsize = 3 + addr_size + phys_size;
+ io_base = 0;
+ for (;rlen >= rentsize; rlen -= rentsize,rangesp += rentsize) {
+ if (((rangesp[0] >> 24) & 0x3) != 1)
+ continue; /* not IO space */
+ io_base = rangesp[3];
+ if (addr_size == 2)
+ io_base = (io_base << 32) | rangesp[4];
+ }
+ if (io_base != 0) {
+ naca->serialPortAddr = io_base + reg->address;
+ if (default_speed && spd)
+ *default_speed = *spd;
+ }
+ of_node_put(pci);
+ next_port:
+ of_node_put(isa);
+ }
+
+ DBG(" <- generic_find_legacy_serial_port()\n");
+}
+
+struct old_serial_port *get_legacy_serial_ports(unsigned int *count)
+{
+ *count = old_serial_count;
+ return old_serial_ports;
+}
+#else
+struct old_serial_port *get_legacy_serial_ports(unsigned int *count)
+{
+ *count = 0;
+ return 0;
+}
+#endif /* CONFIG_PPC_ISERIES */
+EXPORT_SYMBOL(get_legacy_serial_ports);
+
#ifdef CONFIG_XMON
static int __init early_xmon(char *p)
{
Index: linux-work/arch/ppc64/kernel/udbg.c
===================================================================
--- linux-work.orig/arch/ppc64/kernel/udbg.c 2004-10-17 12:07:07.000000000 +1000
+++ linux-work/arch/ppc64/kernel/udbg.c 2004-10-23 11:43:59.357244720 +1000
@@ -49,15 +49,28 @@
static volatile struct NS16550 *udbg_comport;
-void udbg_init_uart(void *comport)
+void udbg_init_uart(void *comport, unsigned int speed)
{
+ u8 dll = 12;
+
+ switch(speed) {
+ case 115200:
+ dll = 1;
+ break;
+ case 57600:
+ dll = 2;
+ break;
+ case 38400:
+ dll = 3;
+ break;
+ }
if (comport) {
udbg_comport = (struct NS16550 *)comport;
udbg_comport->lcr = 0x00; eieio();
udbg_comport->ier = 0xFF; eieio();
udbg_comport->ier = 0x00; eieio();
udbg_comport->lcr = 0x80; eieio(); /* Access baud rate */
- udbg_comport->dll = 12; eieio(); /* 1 = 115200, 2 = 57600, 3 = 38400, 12 = 9600 baud */
+ udbg_comport->dll = dll; eieio(); /* 1 = 115200, 2 = 57600, 3 = 38400, 12 = 9600 baud */
udbg_comport->dlm = 0; eieio(); /* dll >> 8 which should be zero for fast rates; */
udbg_comport->lcr = 0x03; eieio(); /* 8 data, 1 stop, no parity */
udbg_comport->mcr = 0x03; eieio(); /* RTS/DTR */
Index: linux-work/include/asm-ppc64/serial.h
===================================================================
--- linux-work.orig/include/asm-ppc64/serial.h 2004-09-24 14:36:14.000000000 +1000
+++ linux-work/include/asm-ppc64/serial.h 2004-10-23 11:43:59.359244416 +1000
@@ -18,113 +18,13 @@
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
-#define BASE_BAUD ( 1843200 / 16 )
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define RS_TABLE_SIZE 64
-#else
-#define RS_TABLE_SIZE 4
-#endif
-
-/* Standard COM flags (except for COM4, because of the 8514 problem) */
-#ifdef CONFIG_SERIAL_DETECT_IRQ
-#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ)
-#else
-#define STD_COM_FLAGS ASYNC_BOOT_AUTOCONF
-#endif
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#define HUB6_FLAGS 0
-#endif
-
-/*
- * The following define the access methods for the HUB6 card. All
- * access is through two ports for all 24 possible chips. The card is
- * selected through the high 2 bits, the port on that card with the
- * "middle" 3 bits, and the register on that port with the bottom
- * 3 bits.
- *
- * While the access port and interrupt is configurable, the default
- * port locations are 0x302 for the port control register, and 0x303
- * for the data read/write register. Normally, the interrupt is at irq3
- * but can be anything from 3 to 7 inclusive. Note that using 3 will
- * require disabling com2.
- */
-
-#define C_P(card,port) (((card)<<6|(port)<<3) + 1)
-#define STD_SERIAL_PORT_DEFNS \
- /* UART CLK PORT IRQ FLAGS */ \
- { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
- { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
- { 0, BASE_BAUD, 0x890, 0xf, STD_COM_FLAGS }, /* ttyS2 */ \
- { 0, BASE_BAUD, 0x898, 0xe, STD_COM_FLAGS }, /* ttyS3 */
-
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
- { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
- { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
- { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
- { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
- { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
- { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
- { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
- { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
- { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
- { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
- { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
- { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
- { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
- { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
- { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
- { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
-#else
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif
-
-/* You can have up to four HUB6's in the system, but I've only
- * included two cards here for a total of twelve ports.
- */
-#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
-#define HUB6_SERIAL_PORT_DFNS \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */
-#else
-#define HUB6_SERIAL_PORT_DFNS
-#endif
-
-#define MCA_SERIAL_PORT_DFNS
+/* Default baud base if not found in device-tree */
+#define BASE_BAUD ( 1843200 / 16 )
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS \
- HUB6_SERIAL_PORT_DFNS \
- MCA_SERIAL_PORT_DFNS
+#define ARCH_HAS_GET_LEGACY_SERIAL_PORTS
+struct old_serial_port;
+extern struct old_serial_port *get_legacy_serial_ports(unsigned int *count);
+#define UART_NR (8 + CONFIG_SERIAL_8250_NR_UARTS)
#endif /* _PPC64_SERIAL_H */
Index: linux-work/arch/ppc64/kernel/pSeries_setup.c
===================================================================
--- linux-work.orig/arch/ppc64/kernel/pSeries_setup.c 2004-10-17 12:07:07.000000000 +1000
+++ linux-work/arch/ppc64/kernel/pSeries_setup.c 2004-10-23 11:43:59.360244264 +1000
@@ -82,6 +82,8 @@
extern int pSeries_set_rtc_time(struct rtc_time *rtc_time);
extern void find_udbg_vterm(void);
extern void SystemReset_FWNMI(void), MachineCheck_FWNMI(void); /* from head.S */
+extern void generic_find_legacy_serial_ports(unsigned int *default_speed);
+
int fwnmi_active; /* TRUE if an FWNMI handler is present */
unsigned long virtPython0Facilities = 0; // python0 facility area (memory mapped io) (64-bit format) VIRTUAL address.
@@ -189,75 +191,6 @@
arch_initcall(pSeries_init_panel);
-
-void __init pSeries_find_serial_port(void)
-{
- struct device_node *np;
- unsigned long encode_phys_size = 32;
- u32 *sizeprop;
-
- struct isa_reg_property {
- u32 space;
- u32 address;
- u32 size;
- };
- struct pci_reg_property {
- struct pci_address addr;
- u32 size_hi;
- u32 size_lo;
- };
-
- DBG(" -> pSeries_find_serial_port()\n");
-
- naca->serialPortAddr = 0;
-
- np = of_find_node_by_path("/");
- if (!np)
- return;
- sizeprop = (u32 *)get_property(np, "#size-cells", NULL);
- if (sizeprop != NULL)
- encode_phys_size = (*sizeprop) << 5;
-
- for (np = NULL; (np = of_find_node_by_type(np, "serial"));) {
- struct device_node *isa, *pci;
- struct isa_reg_property *reg;
- union pci_range *rangesp;
- char *typep;
-
- typep = (char *)get_property(np, "ibm,aix-loc", NULL);
- if ((typep == NULL) || (typep && strcmp(typep, "S1")))
- continue;
-
- reg = (struct isa_reg_property *)get_property(np, "reg", NULL);
-
- isa = of_get_parent(np);
- if (!isa) {
- DBG("no isa parent found\n");
- break;
- }
- pci = of_get_parent(isa);
- if (!pci) {
- DBG("no pci parent found\n");
- break;
- }
-
- rangesp = (union pci_range *)get_property(pci, "ranges", NULL);
-
- if ( encode_phys_size == 32 )
- naca->serialPortAddr = rangesp->pci32.phys+reg->address;
- else {
- naca->serialPortAddr =
- ((((unsigned long)rangesp->pci64.phys_hi) << 32)
- |
- (rangesp->pci64.phys_lo)) + reg->address;
- }
- break;
- }
-
- DBG(" <- pSeries_find_serial_port()\n");
-}
-
-
/* Build up the firmware_features bitmask field
* using contents of device-tree/ibm,hypertas-functions.
* Ultimately this functionality may be moved into prom.c prom_init().
@@ -337,6 +270,7 @@
{
void *comport;
int iommu_off = 0;
+ unsigned int default_speed;
DBG(" -> pSeries_init_early()\n");
@@ -350,14 +284,14 @@
get_property(of_chosen, "linux,iommu-off", NULL));
}
- pSeries_find_serial_port();
+ generic_find_legacy_serial_ports(&default_speed);
if (systemcfg->platform & PLATFORM_LPAR)
find_udbg_vterm();
else if (naca->serialPortAddr) {
/* Map the uart for udbg. */
comport = (void *)__ioremap(naca->serialPortAddr, 16, _PAGE_NO_CACHE);
- udbg_init_uart(comport);
+ udbg_init_uart(comport, default_speed);
ppc_md.udbg_putc = udbg_putc;
ppc_md.udbg_getc = udbg_getc;
Index: linux-work/include/asm-ppc64/udbg.h
===================================================================
--- linux-work.orig/include/asm-ppc64/udbg.h 2004-09-24 14:36:15.000000000 +1000
+++ linux-work/include/asm-ppc64/udbg.h 2004-10-23 11:43:59.360244264 +1000
@@ -10,7 +10,7 @@
* 2 of the License, or (at your option) any later version.
*/
-void udbg_init_uart(void *comport);
+void udbg_init_uart(void *comport, unsigned int speed);
void udbg_putc(unsigned char c);
unsigned char udbg_getc(void);
int udbg_getc_poll(void);
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/