Re: [PATCH] PCI fixes for 2.6.10-rc1

From: Greg KH
Date: Fri Nov 12 2004 - 18:44:43 EST


ChangeSet 1.2026.55.3, 2004/11/01 15:02:37-08:00, dlsy@xxxxxxxxxxxxxxxxxxxxxxx

[PATCH] PCI: Updated patch to fix adapter speed mismatch for 2.6 kernel

After doing more testing, I found that I couldn't use quirk to set the flag
to identify the chipset, for there are platforms that have other bridge
chip with PCI-X hotpluggable slots in the same system. Therefore, I use
the vendor id and device id to identify the bridge chip that needs the
workaround. The code doing the workaround remains unchanged.


Signed-off-by: Dely Sy <dely.l.sy@xxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <greg@xxxxxxxxx>


drivers/pci/hotplug/shpchp_ctrl.c | 34 ++++++++++++++++++++++++++++++++++
1 files changed, 34 insertions(+)


diff -Nru a/drivers/pci/hotplug/shpchp_ctrl.c b/drivers/pci/hotplug/shpchp_ctrl.c
--- a/drivers/pci/hotplug/shpchp_ctrl.c 2004-11-12 15:13:50 -08:00
+++ b/drivers/pci/hotplug/shpchp_ctrl.c 2004-11-12 15:13:50 -08:00
@@ -1157,6 +1157,40 @@
return -1;
}

+
+ if ((ctrl->pci_dev->vendor == 0x8086) && (ctrl->pci_dev->device == 0x0332)) {
+ if (slots_not_empty)
+ return WRONG_BUS_FREQUENCY;
+
+ if ((rc = p_slot->hpc_ops->set_bus_speed_mode(p_slot, PCI_SPEED_33MHz))) {
+ err("%s: Issue of set bus speed mode command failed\n", __FUNCTION__);
+ up(&ctrl->crit_sect);
+ return WRONG_BUS_FREQUENCY;
+ }
+ wait_for_ctrl_irq (ctrl);
+
+ if ((rc = p_slot->hpc_ops->check_cmd_status(ctrl))) {
+ err("%s: Can't set bus speed/mode in the case of adapter & bus mismatch\n",
+ __FUNCTION__);
+ err("%s: Error code (%d)\n", __FUNCTION__, rc);
+ up(&ctrl->crit_sect);
+ return WRONG_BUS_FREQUENCY;
+ }
+ /* turn on board, blink green LED, turn off Amber LED */
+ if ((rc = p_slot->hpc_ops->slot_enable(p_slot))) {
+ err("%s: Issue of Slot Enable command failed\n", __FUNCTION__);
+ up(&ctrl->crit_sect);
+ return rc;
+ }
+ wait_for_ctrl_irq (ctrl);
+
+ if ((rc = p_slot->hpc_ops->check_cmd_status(ctrl))) {
+ err("%s: Failed to enable slot, error code(%d)\n", __FUNCTION__, rc);
+ up(&ctrl->crit_sect);
+ return rc;
+ }
+ }
+
rc = p_slot->hpc_ops->get_adapter_speed(p_slot, &adapter_speed);
/* 0 = PCI 33Mhz, 1 = PCI 66 Mhz, 2 = PCI-X 66 PA, 4 = PCI-X 66 ECC, */
/* 5 = PCI-X 133 PA, 7 = PCI-X 133 ECC, 0xa = PCI-X 133 Mhz 266, */

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/