[PATCH2 4/6] isicom: Pci probing added

[Jiri Slaby]

Pci probing added

Pci probing functions added, most of functions rewrited because od it (some
for cycles are redundant).
Used PCI_DEVICE macro.

Generated in 2.6.14-rc2-mm2 kernel version

Signed-off-by: Jiri Slaby <xslaby@xxxxxxxxxx>

---
 drivers/char/isicom.c |  468 +++++++++++++++++++++++++++----------------------
 1 files changed, 261 insertions(+), 207 deletions(-)

diff --git a/drivers/char/isicom.c b/drivers/char/isicom.c
--- a/drivers/char/isicom.c
+++ b/drivers/char/isicom.c
@@ -107,7 +107,6 @@
  *	Omit those entries for boards you don't have installed.
  *
  *	TODO
- *		Hotplug
  *		Merge testing
  *		64-bit verification
  */
@@ -146,20 +145,30 @@
 #define isicom_paranoia_check(a, b, c) 0
 #endif
 
+static int isicom_probe(struct pci_dev*, const struct pci_device_id*);
+static void __devexit isicom_remove(struct pci_dev*);
+
 static struct pci_device_id isicom_pci_tbl[] = {
-	{ VENDOR_ID, 0x2028, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
-	{ VENDOR_ID, 0x2051, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
-	{ VENDOR_ID, 0x2052, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
-	{ VENDOR_ID, 0x2053, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
-	{ VENDOR_ID, 0x2054, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
-	{ VENDOR_ID, 0x2055, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
-	{ VENDOR_ID, 0x2056, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
-	{ VENDOR_ID, 0x2057, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
-	{ VENDOR_ID, 0x2058, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+	{ PCI_DEVICE(VENDOR_ID, 0x2028) },
+	{ PCI_DEVICE(VENDOR_ID, 0x2051) },
+	{ PCI_DEVICE(VENDOR_ID, 0x2052) },
+	{ PCI_DEVICE(VENDOR_ID, 0x2053) },
+	{ PCI_DEVICE(VENDOR_ID, 0x2054) },
+	{ PCI_DEVICE(VENDOR_ID, 0x2055) },
+	{ PCI_DEVICE(VENDOR_ID, 0x2056) },
+	{ PCI_DEVICE(VENDOR_ID, 0x2057) },
+	{ PCI_DEVICE(VENDOR_ID, 0x2058) },
 	{ 0 }
 };
 MODULE_DEVICE_TABLE(pci, isicom_pci_tbl);
 
+static struct pci_driver isicom_driver = {
+	.name		= "isicom",
+	.id_table	= isicom_pci_tbl,
+	.probe		= isicom_probe,
+	.remove		= __devexit_p(isicom_remove)
+};
+
 static int prev_card = 3;	/*	start servicing isi_card[0]	*/
 static struct tty_driver *isicom_normal;
 
@@ -171,8 +180,6 @@ static int ISILoad_ioctl(struct inode *i
 static void isicom_tx(unsigned long _data);
 static void isicom_start(struct tty_struct *tty);
 
-static unsigned char *tmp_buf;
-
 /*   baud index mappings from linux defns to isi */
 
 static signed char linuxb_to_isib[] = {
@@ -191,6 +198,7 @@ struct	isi_board {
 	u8			isa;
 	spinlock_t		card_lock; /* Card wide lock 11/5/00 -sameer */
 	unsigned long		flags;
+	struct device		device;
 };
 
 struct	isi_port {
@@ -1379,7 +1387,7 @@ static int isicom_write(struct tty_struc
 	if (isicom_paranoia_check(port, tty->name, "isicom_write"))
 		return 0;
 
-	if (!tty || !port->xmit_buf || !tmp_buf)
+	if (!tty || !port->xmit_buf)
 		return 0;
 
 	spin_lock_irqsave(&card->card_lock, flags);
@@ -1745,32 +1753,36 @@ static void isicom_flush_buffer(struct t
 	tty_wakeup(tty);
 }
 
+/*
+ * Driver init and deinit functions
+ */
 
-static int __devinit register_ioregion(void)
+static int __devinit isicom_register_ioregion(struct isi_board *board,
+	const unsigned int index)
 {
-	int count, done=0;
-	for (count=0; count < BOARD_COUNT; count++ ) {
-		if (isi_card[count].base)
-			if (!request_region(isi_card[count].base,16,ISICOM_NAME)) {
-				printk(KERN_DEBUG "ISICOM: I/O Region 0x%x-0x%x is busy. Card%d will be disabled.\n",
-					isi_card[count].base,isi_card[count].base+15,count+1);
-				isi_card[count].base=0;
-				done++;
-			}
-	}
-	return done;
+	if (!board->base)
+		return -EINVAL;
+
+	if (!request_region(board->base, 16, ISICOM_NAME)) {
+		printk(KERN_DEBUG "ISICOM: I/O Region 0x%x-0x%x is busy. "
+			"Card%d will be disabled.\n", board->base,
+			board->base + 15, index + 1);
+		return -EBUSY;
+ 	}
+
+	return 0;
 }
 
-static void unregister_ioregion(void)
+static void isicom_unregister_ioregion(struct isi_board *board,
+	const unsigned int index)
 {
-	int count;
-	for (count=0; count < BOARD_COUNT; count++ )
-		if (isi_card[count].base) {
-			release_region(isi_card[count].base,16);
-#ifdef ISICOM_DEBUG
-			printk(KERN_DEBUG "ISICOM: I/O Region 0x%x-0x%x released for Card%d.\n",isi_card[count].base,isi_card[count].base+15,count+1);
-#endif
-		}
+	if (!board->base)
+		return;
+
+	release_region(board->base, 16);
+	board->base = 0;
+	pr_deb(KERN_DEBUG "ISICOM: I/O Region 0x%x-0x%x released for Card%d.\n",
+		board->base, board->base + 15, index + 1);
 }
 
 static struct tty_operations isicom_ops = {
@@ -1835,207 +1847,243 @@ static void isicom_unregister_tty_driver
 	put_tty_driver(isicom_normal);
 }
 
-static int __devinit register_isr(void)
+static int __devinit isicom_register_isr(struct isi_board *board,
+	const unsigned int index)
 {
-	int count, done=0;
-	unsigned long irqflags;
+	unsigned long irqflags = SA_INTERRUPT;
+	int retval = -EINVAL;
 
-	for (count=0; count < BOARD_COUNT; count++ ) {
-		if (isi_card[count].base) {
-			irqflags = (isi_card[count].isa == YES) ?
-					SA_INTERRUPT :
-					(SA_INTERRUPT | SA_SHIRQ);
-
-			if (request_irq(isi_card[count].irq,
-					isicom_interrupt,
-					irqflags,
-					ISICOM_NAME, &isi_card[count])) {
-
-				printk(KERN_WARNING "ISICOM: Could not"
-					" install handler at Irq %d."
-					" Card%d will be disabled.\n",
-					isi_card[count].irq, count+1);
+	if (!board->base)
+		goto end;
 
-				release_region(isi_card[count].base,16);
-				isi_card[count].base=0;
-			}
-			else
-				done++;
-		}
-	}
-	return done;
+	if (board->isa == NO)
+		irqflags |= SA_SHIRQ;
+
+	retval = request_irq(board->irq, isicom_interrupt, irqflags,
+		ISICOM_NAME, board);
+	if (retval < 0) {
+		printk(KERN_WARNING "ISICOM: Could not install handler at Irq "
+			"%d. Card%d will be disabled.\n", board->irq,
+			index + 1);
+ 	} else
+		retval = 0;
+end:
+	return retval;
 }
 
-static void __exit unregister_isr(void)
+static void isicom_unregister_isr(struct isi_board *board)
 {
-	int count;
-
-	for (count=0; count < BOARD_COUNT; count++ ) {
-		if (isi_card[count].base)
-			free_irq(isi_card[count].irq, &isi_card[count]);
-	}
+	if (board->base)
+		free_irq(board->irq, board);
 }
 
-static int __devinit isicom_init(void)
+static int __devinit reset_card(struct isi_board *board,
+	const unsigned int card, unsigned int *signature)
 {
-	int card, channel, base;
-	struct isi_port *port;
-	unsigned long page;
+	u16 base = board->base;
+	unsigned int portcount = 0;
+	int retval = 0;
 
-	if (!tmp_buf) {
-		page = get_zeroed_page(GFP_KERNEL);
-		if (!page) {
-#ifdef ISICOM_DEBUG
-			printk(KERN_DEBUG "ISICOM: Couldn't allocate page for tmp_buf.\n");
-#else
-			printk(KERN_ERR "ISICOM: Not enough memory...\n");
-#endif
-			return 0;
-		}
-		tmp_buf = (unsigned char *) page;
-	}
+	printk(KERN_DEBUG "ISILoad:Resetting Card%d at 0x%x\n", card + 1, base);
 
-	if (!register_ioregion())
-	{
-		printk(KERN_ERR "ISICOM: All required I/O space found busy.\n");
-		free_page((unsigned long)tmp_buf);
-		return 0;
-	}
-	if (isicom_register_tty_driver())
-	{
-		unregister_ioregion();
-		free_page((unsigned long)tmp_buf);
-		return 0;
-	}
-	if (!register_isr())
-	{
-		isicom_unregister_tty_driver();
-		/*  ioports already uregistered in register_isr */
-		free_page((unsigned long)tmp_buf);
-		return 0;
-	}
+	inw(base + 0x8);
 
-	memset(isi_ports, 0, sizeof(isi_ports));
-	for (card = 0; card < BOARD_COUNT; card++) {
-		port = &isi_ports[card * 16];
-		isi_card[card].ports = port;
-		spin_lock_init(&isi_card[card].card_lock);
-		base = isi_card[card].base;
-		for (channel = 0; channel < 16; channel++, port++) {
-			port->magic = ISICOM_MAGIC;
-			port->card = &isi_card[card];
-			port->channel = channel;
-			port->close_delay = 50 * HZ/100;
-			port->closing_wait = 3000 * HZ/100;
-			INIT_WORK(&port->hangup_tq, do_isicom_hangup, port);
-			INIT_WORK(&port->bh_tqueue, isicom_bottomhalf, port);
-			port->status = 0;
-			init_waitqueue_head(&port->open_wait);
-			init_waitqueue_head(&port->close_wait);
-			/*  . . .  */
+	mdelay(10);
+
+	outw(0, base + 0x8); /* Reset */
+
+	msleep(3000);
+
+	*signature = inw(base + 0x4) & 0xff;
+
+	if (board->isa == YES) {
+		if (!(inw(base + 0xe) & 0x1) || (inw(base + 0x2))) {
+			pr_deb(KERN_DEBUG "base+0x2=0x%x, base+0xe=0x%x",
+				inw(base + 0x2), inw(base + 0xe));
+			printk(KERN_ERR "ISILoad:ISA Card%d reset failure "
+				"(Possible bad I/O Port Address 0x%x).\n",
+				card + 1, base);
+			retval = -EIO;
+			goto end;
+		}
+	} else {
+		portcount = inw(base + 0x2);
+		if (!(inw(base + 0xe) & 0x1) || ((portcount != 0) &&
+				(portcount != 4) && (portcount != 8))) {
+			pr_deb("\nbase+0x2=0x%x , base+0xe=0x%x",
+				inw(base + 0x2), inw(base + 0xe));
+			printk("\nISILoad:PCI Card%d reset failure (Possible "
+				"bad I/O Port Address 0x%x).\n", card + 1,
+				base);
+			retval = -EIO;
+			goto end;
 		}
 	}
 
-	return 1;
+	switch (*signature) {
+	case 0xa5:
+	case 0xbb:
+	case 0xdd:
+		board->port_count = (board->isa == NO && portcount == 4) ? 4 :
+			8;
+		board->shift_count = 12;
+		break;
+	case 0xcc:
+		board->port_count = 16;
+		board->shift_count = 11;
+		break;
+	default:
+		printk(KERN_WARNING "ISILoad:Card%d reset failure (Possible "
+			"bad I/O Port Address 0x%x).\n", card + 1, base);
+		pr_deb(KERN_DEBUG "Sig=0x%x\n", signature);
+		retval = -EIO;
+	}
+	printk(KERN_INFO "-Done\n");
+
+end:
+	return retval;
 }
 
 /*
  *	Insmod can set static symbols so keep these static
  */
-
 static int io[4];
 static int irq[4];
+static int card;
 
-static int __devinit isicom_setup(void)
+static int __devinit isicom_probe(struct pci_dev *pdev,
+	const struct pci_device_id *ent)
 {
-	struct pci_dev *dev = NULL;
-	int retval, card, idx, count;
-	unsigned char pciirq;
-	unsigned int ioaddr;
-
-	card = 0;
-	for (idx=0; idx < BOARD_COUNT; idx++) {
-		if (io[idx]) {
-			isi_card[idx].base=io[idx];
-			isi_card[idx].irq=irq[idx];
-			isi_card[idx].isa=YES;
-			card++;
-		}
-		else {
-			isi_card[idx].base = 0;
-			isi_card[idx].irq = 0;
+	unsigned int ioaddr, signature, index;
+	int retval = -EPERM;
+	u8 pciirq;
+	struct isi_board *board = NULL;
+
+	if (card >= BOARD_COUNT)
+		goto err;
+
+	ioaddr = pci_resource_start(pdev, 3);
+	/* i.e at offset 0x1c in the PCI configuration register space. */
+	pciirq = pdev->irq;
+	printk(KERN_INFO "ISI PCI Card(Device ID 0x%x)\n", ent->device);
+
+	/* allot the first empty slot in the array */
+	for (index = 0; index < BOARD_COUNT; index++)
+		if (isi_card[index].base == 0) {
+			board = &isi_card[index];
+			break;
 		}
-	}
 
-	for (idx=0 ;idx < card; idx++) {
-		if (!((isi_card[idx].irq==2)||(isi_card[idx].irq==3)||
-			(isi_card[idx].irq==4)||(isi_card[idx].irq==5)||
-			(isi_card[idx].irq==7)||(isi_card[idx].irq==10)||
-			(isi_card[idx].irq==11)||(isi_card[idx].irq==12)||
-			(isi_card[idx].irq==15))) {
-
-			if (isi_card[idx].base) {
-				printk(KERN_ERR "ISICOM: Irq %d unsupported. Disabling Card%d...\n",
-					isi_card[idx].irq, idx+1);
-				isi_card[idx].base=0;
-				card--;
-			}
-		}
-	}
+	board->base = ioaddr;
+	board->irq = pciirq;
+	board->isa = NO;
+	board->device = pdev->dev;
+	card++;
+
+	retval = isicom_register_ioregion(board, index);
+	if (retval < 0)
+		goto err;
+
+	retval = isicom_register_isr(board, index);
+	if (retval < 0)
+		goto errunrr;
+
+	retval = reset_card(board, index, &signature);
+	if (retval < 0)
+		goto errunri;
+
+/*	retval = load_firmware(board, index, signature);
+	if (retval < 0)
+		goto errunri; */
 
-	if (card < BOARD_COUNT) {
-		for (idx=0; idx < DEVID_COUNT; idx++) {
-			dev = NULL;
-			for (;;){
-				if (!(dev = pci_find_device(VENDOR_ID, isicom_pci_tbl[idx].device, dev)))
-					break;
-				if (card >= BOARD_COUNT)
-					break;
+	return 0;
 
-				if (pci_enable_device(dev))
-					break;
+errunri:
+	isicom_unregister_isr(board);
+errunrr:
+	isicom_unregister_ioregion(board, index);
+err:
+	board->base = 0;
+	return retval;
+}
 
-				/* found a PCI ISI card! */
-				ioaddr = pci_resource_start (dev, 3);
-				/* i.e at offset 0x1c in the
-				 * PCI configuration register
-				 * space.
-				 */
-				pciirq = dev->irq;
-				printk(KERN_INFO "ISI PCI Card(Device ID 0x%x)\n", isicom_pci_tbl[idx].device);
-				/*
-				 * allot the first empty slot in the array
-				 */
-				for (count=0; count < BOARD_COUNT; count++) {
-					if (isi_card[count].base == 0) {
-						isi_card[count].base = ioaddr;
-						isi_card[count].irq = pciirq;
-						isi_card[count].isa = NO;
-						card++;
-						break;
-					}
-				}
-			}
-			if (card >= BOARD_COUNT) break;
-		}
-	}
+static void __devexit isicom_remove(struct pci_dev *pdev)
+{
+	unsigned int idx;
 
-	if (!(isi_card[0].base || isi_card[1].base || isi_card[2].base || isi_card[3].base)) {
-		printk(KERN_ERR "ISICOM: No valid card configuration. Driver cannot be initialized...\n");
-		return -EIO;
-	}
+	for (idx = 0; idx < BOARD_COUNT; idx++)
+		if (isi_card[idx].base == pci_resource_start(pdev, 3))
+			break;
 
-	retval = misc_register(&isiloader_device);
+	if (idx == BOARD_COUNT)
+		return;
+
+	isicom_unregister_isr(&isi_card[idx]);
+	isicom_unregister_ioregion(&isi_card[idx], idx);
+}
+
+static int __devinit isicom_setup(void)
+{
+	int retval, idx, channel;
+	struct isi_port *port;
+
+	card = 0;
+	memset(isi_ports, 0, sizeof(isi_ports));
+
+	for(idx = 0; idx < BOARD_COUNT; idx++) {
+		port = &isi_ports[idx * 16];
+		isi_card[idx].ports = port;
+		spin_lock_init(&isi_card[idx].card_lock);
+		for (channel = 0; channel < 16; channel++, port++) {
+			port->magic = ISICOM_MAGIC;
+			port->card = &isi_card[idx];
+			port->channel = channel;
+			port->close_delay = 50 * HZ/100;
+			port->closing_wait = 3000 * HZ/100;
+			INIT_WORK(&port->hangup_tq, do_isicom_hangup, port);
+			INIT_WORK(&port->bh_tqueue, isicom_bottomhalf, port);
+			port->status = 0;
+			init_waitqueue_head(&port->open_wait);
+			init_waitqueue_head(&port->close_wait);
+			/*  . . .  */
+ 		}
+		isi_card[idx].base = 0;
+		isi_card[idx].irq = 0;
+
+		if (!io[idx])
+			continue;
+
+		if (irq[idx] == 2 || irq[idx] == 3 || irq[idx] == 4	||
+				irq[idx] == 5	|| irq[idx] == 7	||
+				irq[idx] == 10	|| irq[idx] == 11	||
+				irq[idx] == 12	|| irq[idx] == 15) {
+			printk(KERN_ERR "ISICOM: ISA not supported yet.\n");
+			return -EIO;
+/*			isi_card[idx].base = io[idx];
+			isi_card[idx].irq = irq[idx];
+			isi_card[idx].isa = YES;
+ FIXME: which device for request_firmware use? if you know, uncomment this and
+ delete printk and return
+			isi_card[idx].device = ???;
+			card++;*/
+		} else
+			printk(KERN_ERR "ISICOM: Irq %d unsupported. "
+				"Disabling Card%d...\n", irq[idx], idx + 1);
+	}
+
+	retval = isicom_register_tty_driver();
+	if (retval < 0)
+		goto error;
+
+	retval = pci_register_driver(&isicom_driver);
 	if (retval < 0) {
-		printk(KERN_ERR "ISICOM: Unable to register firmware loader driver.\n");
-		return retval;
+		printk(KERN_ERR "ISICOM: Unable to register pci driver.\n");
+		goto errtty;
 	}
 
-	if (!isicom_init()) {
-		if (misc_deregister(&isiloader_device))
-			printk(KERN_ERR "ISICOM: Unable to unregister Firmware Loader driver\n");
-		return -EIO;
-	}
+	retval = misc_register(&isiloader_device);
+	if (retval < 0)
+		goto errpci;
 
 	init_timer(&tx);
 	tx.expires = jiffies + 1;
@@ -2045,6 +2093,12 @@ static int __devinit isicom_setup(void)
 	add_timer(&tx);
 
 	return 0;
+errpci:
+	pci_unregister_driver(&isicom_driver);
+errtty:
+	isicom_unregister_tty_driver();
+error:
+	return retval;
 }
 
 static void __exit isicom_exit(void)
@@ -2056,13 +2110,13 @@ static void __exit isicom_exit(void)
 	while (re_schedule != 2 && index++ < 100)
 		msleep(10);
 
-	unregister_isr();
+	pci_unregister_driver(&isicom_driver);
 	isicom_unregister_tty_driver();
-	unregister_ioregion();
-	if (tmp_buf)
-		free_page((unsigned long)tmp_buf);
-	if (misc_deregister(&isiloader_device))
-		printk(KERN_ERR "ISICOM: Unable to unregister Firmware Loader driver\n");
+
+	for (index = 0; index < BOARD_COUNT; index++) {
+		isicom_unregister_isr(&isi_card[index]);
+		isicom_unregister_ioregion(&isi_card[index], index);
+	}
 }
 
 module_init(isicom_setup);
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/