Re: vt6410 Problems

[Mathias Kretschmer]

Chuck Wolber wrote:
> Greetings,
> 
> Using vanilla 2.6.15.4 on an ASUS P4P800, I have a Maxtor 4A250J0 attached
> to the VT6410 IDE port. It shows up as /dev/hdf and no matter what I do,
> the system believes it is being used and will not format or mount it.

Try configuring the drive as master (hde) and not as
slave-without-a-master (hdf).



> 
> Attempting to format the drive (regardless of partition size) gets:
> 
> root@bailey:/usr/src/linux# mke2fs -j /dev/hdf1
> mke2fs 1.38 (30-Jun-2005)
> /dev/hdf1 is apparently in use by the system; will not make a filesystem 
> here!
> 
> (And yes, I have driven myself batty assuring myself that it is *NOT* in 
> fact mounted.)
> 
> 
> I can override the message and format it anyway with:
> 
> root@bailey:/usr/src/linux# mke2fs -j -F /dev/hdf1
> mke2fs 1.38 (30-Jun-2005)
> /dev/hdf1 is apparently in use by the system; mke2fs forced anyway.
> Filesystem label=
> OS type: Linux
> Block size=1024 (log=0)
> Fragment size=1024 (log=0)
> 2000 inodes, 8000 blocks
> 400 blocks (5.00%) reserved for the super user
> First data block=1
> 1 block group
> 8192 blocks per group, 8192 fragments per group
> 2000 inodes per group
> 
> Writing inode tables: done
> Creating journal (1024 blocks): mke2fs: Device or resource busy
>         while trying to create journal
> 
> 
> 
> But then when I dump the filesystem, I get:
> 
> root@bailey:/usr/src/linux# dumpe2fs /dev/hdf1
> dumpe2fs 1.38 (30-Jun-2005)
> dumpe2fs: Bad magic number in super-block while trying to open /dev/hdf1
> Couldn't find valid filesystem superblock.
> 
> 
> Clearly nothing was written to the drive...
> 
> 
> The dmesg output is as follows:
> 
> [4294673.024000] VP_IDE: chipset revision 6
> [4294673.024000] VP_IDE: VIA vt6410 (rev 06) IDE UDMA133 controller on 
> pci0000:02:04.0
> [4294673.024000] VP_IDE: 100% native mode on irq 19
> [4294673.024000]     ide2: BM-DMA at 0xe400-0xe407, BIOS settings: 
> hde:pio, hdf:pio
> [4294673.024000]     ide3: BM-DMA at 0xe408-0xe40f, BIOS settings: 
> hdg:pio, hdh:pio
> [4294673.024000] Probing IDE interface ide2...
> [4294673.492000] hdf: Maxtor 4A250J0, ATA DISK drive
> [4294673.543000] ide2 at 0xec00-0xec07,0xe882 on irq 19
> [4294673.543000] hdf: max request size: 1024KiB
> [4294673.554000] usb 1-1: new full speed USB device using uhci_hcd and 
> address 4
> [4294673.573000] hdf: 490234752 sectors (251000 MB) w/2048KiB Cache, 
> CHS=30515/255/63, UDMA(133)
> [4294673.573000] hdf: cache flushes supported
> [4294673.573000]  hdf: hdf1
> [4294673.576000] Probing IDE interface ide3...
> 
> 
> 
> The hdparm information on the drive is:
> 
> /dev/hdf:
> 
> ATA device, with non-removable media
>         Model Number:       Maxtor 4A250J0
>         Serial Number:      A809GX2E
>         Firmware Revision:  RAMB1TV0
> Standards:
>         Supported: 7 6 5 4
>         Likely used: 7
> Configuration:
>         Logical         max     current
>         cylinders       16383   65535
>         heads           16      1
>         sectors/track   63      63
>         --
>         CHS current addressable sectors:    4128705
>         LBA    user addressable sectors:  268435455
>         LBA48  user addressable sectors:  490234752
>         device size with M = 1024*1024:      239372 MBytes
>         device size with M = 1000*1000:      251000 MBytes (251 GB)
> Capabilities:
>         LBA, IORDY(can be disabled)
>         Queue depth: 1
>         Standby timer values: spec'd by Standard, no device specific 
> minimum
>         R/W multiple sector transfer: Max = 16  Current = 0
>         Advanced power management level: unknown setting (0x0000)
>         Recommended acoustic management value: 192, current value: 192
>         DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
>              Cycle time: min=120ns recommended=120ns
>         PIO: pio0 pio1 pio2 pio3 pio4
>              Cycle time: no flow control=120ns  IORDY flow control=120ns
> Commands/features:
>         Enabled Supported:
>            *    NOP cmd
>            *    READ BUFFER cmd
>            *    WRITE BUFFER cmd
>            *    Host Protected Area feature set
>            *    Look-ahead
>            *    Write cache
>            *    Power Management feature set
>                 Security Mode feature set
>            *    SMART feature set
>            *    FLUSH CACHE EXT command
>            *    Mandatory FLUSH CACHE command
>            *    Device Configuration Overlay feature set
>            *    48-bit Address feature set
>            *    Automatic Acoustic Management feature set
>                 SET MAX security extension
>                 Advanced Power Management feature set
>            *    DOWNLOAD MICROCODE cmd
>            *    SMART self-test
>            *    SMART error logging
> Security:
>         Master password revision code = 65534
>                 supported
>         not     enabled
>         not     locked
>         not     frozen
>         not     expired: security count
>         not     supported: enhanced erase
> HW reset results:
>         CBLID- above Vih
>         Device num = 1 determined by the jumper
> Checksum: correct
> 
> 
> 
> 

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/