Linux-2.6.17: PMTimer results for another PCI chipset

From: Chris Rankin
Date: Sun Jun 25 2006 - 16:41:00 EST

Hi,

This motherboard / chipset runs the pmtimer_test application correctly as well. (PIII / UP).

Linux version 2.6.17 (chris@twopit) (gcc version 4.1.1) #1 SMP Sun Jun 25 20:29:46 BST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffeb000 (usable)
BIOS-e820: 000000001ffeb000 - 000000001ffef000 (ACPI data)
BIOS-e820: 000000001ffef000 - 000000001ffff000 (reserved)
BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 131051
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 126955 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 ASUS ) @ 0x000f7b40
ACPI: RSDT (v001 ASUS TUSL2-C 0x30303031 MSFT 0x31313031) @ 0x1ffeb000
ACPI: FADT (v001 ASUS TUSL2-C 0x30303031 MSFT 0x31313031) @ 0x1ffeb100
ACPI: BOOT (v001 ASUS TUSL2-C 0x30303031 MSFT 0x31313031) @ 0x1ffeb040
ACPI: MADT (v001 ASUS TUSL2-C 0x30303031 MSFT 0x31313031) @ 0x1ffeb080
ACPI: DSDT (v001 ASUS TUSL2-C 0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0xe408

PCI summary:

00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and Memory Controller Hub (rev 04)
00:01.0 PCI bridge: Intel Corp. 82815 815 Chipset AGP Bridge (rev 04)
00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 05)
00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 05)
00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 05)
00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 05)
00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 05)
00:1f.4 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #2) (rev 05)

Full PCI output:

00:00.0 Class 0600: 8086:1130 (rev 04)
Subsystem: 1043:8027
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at fc000000 (32-bit, prefetchable) [size=32M]
Capabilities: [88] #09 [e104]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

00:01.0 Class 0604: 8086:1131 (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f8800000-f9cfffff
Prefetchable memory behind bridge: f9f00000-fbffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-

00:1e.0 Class 0604: 8086:244e (rev 05)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=03, sec-latency=32
I/O behind bridge: 0000b000-0000dfff
Memory behind bridge: f5800000-f87fffff
Prefetchable memory behind bridge: f9d00000-f9efffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 Class 0601: 8086:2440 (rev 05)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:1f.1 Class 0101: 8086:244b (rev 05) (prog-if 80 [Master])
Subsystem: 1043:8027
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at a800 [size=16]

00:1f.2 Class 0c03: 8086:2442 (rev 05)
Subsystem: 1043:8027
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 17
Region 4: I/O ports at a400 [size=32]

00:1f.3 Class 0c05: 8086:2443 (rev 05)
Subsystem: 1043:8027
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at e800 [size=16]

00:1f.4 Class 0c03: 8086:2444 (rev 05)
Subsystem: 1043:8027
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at a000 [size=32]




___________________________________________________________
Inbox full of spam? Get leading spam protection and 1GB storage with All New Yahoo! Mail. http://uk.docs.yahoo.com/nowyoucan.html
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/