2.6.19-rc1 genirq causes either boot hang or "do_IRQ: cannot handle IRQ -1"
From: Muli Ben-Yehuda
Date: Thu Oct 05 2006 - 17:22:46 EST
My x366 no longer boots with 2.6.19-rc1. The boot either hangs in
uhci_hcd_init or dies with 'do_IRQ: cannot handle IRQ -1". Bisection
says this one is bad:
[PATCH] genirq: x86_64 irq: make vector_irq per cpu
author Eric W. Biederman <ebiederm@xxxxxxxxxxxx>
committer Linus Torvalds <torvalds@xxxxxxxxxxx>
commit 550f2299ac8ffaba943cf211380d3a8d3fa75301
http://www.kernel.org/git/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=550f2299ac8ffaba943cf211380d3a8d3fa75301
and this one is fine:
[PATCH] genirq: x86_64 irq: Make the external irq handlers report their vector, not ...
author Eric W. Biederman <ebiederm@xxxxxxxxxxxx>
committer Linus Torvalds <torvalds@xxxxxxxxxxx>
commit e500f57436b9056a245216c53113613928155eba
http://www.kernel.org/git/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=e500f57436b9056a245216c53113613928155eba
Boot logs, lspci -vvv and .config attached.
Boot log with hang in uhci_hcd_init:
kernel (hd0,1)/boot/calgary/bzImage root=/dev/sda2 console=tty0 console=ttyS1,1 9200
[Linux-bzImage, setup=0x1c00, size=0x2e3ad8]
initrd (hd0,1)/boot/calgary/aic94xxfw.initramfs.gz
[Linux-initrd @ 0x37e3f000, 0x1b01e2 bytes]
savedefault
[ 0.000000] Linux version 2.6.18mx (muli@rhun) (gcc version 3.4.1) #147 SMP Thu Oct 5 21:36:48 IST 2006
[ 0.000000] Command line: root=/dev/sda2 console=tty0 console=ttyS1,19200
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 0000000000099000 (usable)
[ 0.000000] BIOS-e820: 0000000000099000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000e7f9c640 (usable)
[ 0.000000] BIOS-e820: 00000000e7f9c640 - 00000000e7fa6a40 (ACPI data)
[ 0.000000] BIOS-e820: 00000000e7fa6a40 - 00000000e8000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000198000000 (usable)
[ 0.000000] end_pfn_map = 1671168
[ 0.000000] DMI 2.3 present.
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1671168
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0 -> 153
[ 0.000000] 0: 256 -> 950172
[ 0.000000] 0: 1048576 -> 1671168
[ 0.000000] ACPI: PM-Timer IO Port: 0x9c
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x06] enabled)
[ 0.000000] Processor #C_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x0f] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 15, address 0xfec00000, GSI 0-35
[ 0.000000] ACPI: IOAPIC (id[0x0e] address[0xfec01000] gsi_base[35])
[ 0.000000] IOAPIC[1]: apic_id)
[ 0.000000] Setting APIC routing to flat
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Nosave address range: 0000000000099000 - 00000000000a0000
[ 0.000000] Nosave address range: 00000000000a0000 - 00000000000e0000
[ 0.000000] Nosave address range: 00000000000e0000 - 0000000000100000
[ 0.000000] Nosave address range: 00000000e7f9c000 - 00000000e7f9d000
[ 0.000000] Nosave address range: 00000000e7f9d000 - 00000000e7fa6000
[ 0.000000] Nosave address range: 00000000e7fa6000 - 00000000e7fa7000
[ 0.000000] Nosave address range: 00000000e7fa7000 - 00000000e8000000
[ 0.000000] Nosave address range: 00000000e8000000 - 00000000fec00000
[ 0.000000] Nosave address range: 00000000fec00000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at ea000000 (gap: e8000000:16c00000)
[ 0.000000] PERCPU: Allocating 34304 bytes of per cpu data
[ 0.000000] Built 1 zonelists. Total pages: 1534048
[ 0.000000] Kernel command line: root=/dev/sda2 console=tty0 console=ttyS1,19200
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 5705] ... MAX_LOCKDEP_KEYS: 2048
[ 168.121904] ... CLASSHASH_SIZE: 1024
[ 168.148620] ... MAX_LOCKDEP_ENTRIES: 8192
[ 168.174819] ... MAX_LOCKDEP_CHAINS: 8192
[ 168.201018] ... CHAINHASH_SIZE: 4096
[ 168.227212] memory used by lock dependency info: 1328 kB
[ 168.259653] per task-struct memory footprint: 1680 bytes
[ 168.299288] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 168.354233] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)[ 168.400617] Checking aperture...
[ 168.442967] PCI-DMA: Calgary IOMMU detected.
[ 168.468663] PCI-DMA: Calgary TCE table spec is 7, CONFIG_IOMMU_DEBUG is enabled.
[ 168.631217] Memory: 6096428k/6684672k available (3788k kernel code, 193716k reserved, 2726k data, 276k init)
[ 168.769306] Calibrating delay using timer specific routine.. 6346.46 BogoMIPS (lpj=12692924)
[ 168.820297] Mount-cache hash table entries: 256
[ 168.849151] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 168.880653] CPU: L2 cache: 1024K
[ 168.900049] using mwait in idle threads.
[ 168.923651] CPU: Physical Processor ID: 0
[ 16[ 169.171779] Using local APIC timer interrupts.
[ 169.230014] result 10425811
[ 169.246796] Detected 10.425 MHz APIC timer.
[ 169.274318] lockdep: not fixing up alternatives.
[ 169.302624] Booting processor 1/4 APIC 0x1
[ 169.337672] Initializing CPU#1
[ 169.417131] Calibrating delay using timer specific routine.. 6339.06 BogoMIPS (lpj=12678127)
[ 169.417148] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 169.417151] CPU: L2 cache: 1024K
[ 169.417155] CPU: Physical Processor ID: 0
[ 169.417157] CPU: Processor Core ID: 0
[ 169.417170] CPU1: Thermal monitoring enabled (TM1)
[ 169.417449] Intel(R) Xeon(TM) MP CPU 3.16GHz stepping 01
[ 169.421461] lockdep: not fixing up alternatives.
[ 169.683506] Booting processor 2/4 APIC 0x6
[ 169.718522] Initializing CPU#2
[ 169.797034] Calibrating delay using timer specific routine.. 6339.24 BogoMIPS (lpj=12677306] Intel(R) Pentium(R) 4 CPU 3.16GHz stepping 09
[ 169.801358] lockdep: not fixing up alternatives.
[ 170.063376] Booting processor 3/4 APIC 0x7
[ 170.098394] Initializing CPU#3
[ 170.176937] Calibrating delay using timer specific routine.. 6339.33 BogoMIPS (lpj=12678668)
[ 170.176953] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 170.176956] CPU: L2 cache: 1024K
[ 170.176959] CPU: Physical Processor ID: 3
[ 170.176961] CPU: Processor Core ID: 0
[ 170.176971] CPU3: Thermal monitoring enabled (TM1)
[ 170.177211] Intel(R) Pentium(R) 4 CPU 3.16GHz stepping 09
[ 170.180968] Brought up 4 CPUs
[ 170.433147] testing NMI watchdog ... OK.
[ 170.496859] time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
[ 170.533946] time.c: Detected 3169.444 MHz processor.
[ 170.732881] migration_cost=1,683
[ 170.753371] checking if image is initramfs... it is
[ 170.945317] Freeing initrd memory: 1728k freed
[ 170.975037] NET: Registered protocol family 16
[ 171.012196] ACPI: bus type pci registered
[ 171.036300] PCI: Using configuration type 1
[ 171.190476] ACPI: Interpreter enabled
[ 171.212520] ACPI: Using IOAPIC for interrupt routing
[ 171.249022] ACPI: PCI Root Bridge [VP00] (0000:00)
[ 171.281222] PCI: Ignoring BAR0-3 of IDE controller 0000:00:0f.1
[ 171.337334] ACPI: PCI Root Bridge [VP01] (0000:01)
[ 171.373147] ACPI: PCI Root Bridge [VP02] (0000:02)
[ 171.411105] ACPI: PCI Root Bridge [VP03] (0000:04)
[ 171.448703] ACPI: PCI Root Bridge [VP04] (0000:06)
[ 171.486345] ACPI: PCI Root Bridge [VP05] (0000:08)
[ 171.524153] ACPI: PCI Root Bridge [VP06] (0000:0a)
[ 171.561037] ACPI: PCI Root Bridge [VP07] (0000:0c)
[ 171.598952] SCSI subsystem initialized
[ 171.621709] usbcore: registered new interface driver usbfs
[ 171.654797] usbcore: registered new interface driver hub
[ 171.686886] usbcore: registered new device driver usb
[ 171.717651] PCI: Using ACPI for IRQ routing
[ 171.742820] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 171.792715] PCI-DMA: Using Calgary IOMMU
[ 172.171973] Calgary: enabling translation on PHB 0
[ 172.200751] Calgary: errant DMAs will now be prevented on this bus.
[ 172.593458] Calgary: enabling translation on PHB 1
[ 172.622214] Calgary: errant DMAs will now be prevented on this bus.
[ 173.015214] Calgary: enabling translation on PHB 2
[ 173.043975] Calgary: errant DMAs will now be prevented on this bus.
[ 173.081667] PCI-GART: No AMD northbridge found.
[ 173.118125] NET: Registered protocol family 2
[ 173.200415 tables configured (established 65536 bind 32768)
[ 173.381286] TCP reno registered
[ 173.422487] Total HugeTLB memory allocated, 0
[ 173.450396] Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
[ 173.489481] io scheduler noop registered
[ 173.513181] io scheduler anticipatory registered (default)
[ 173.546334] io scheduler deadline registered
[ 173.572153] io scheduler cfq registered
[ 173.602544] GSI 16 sharing vector 0xA9 and IRQ 16
[ 173.630881] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 173.675669] radeonfb: Found Intel x86 BIOS ROM Image
[ 173.720028] radeonfb: Retrieved PLL infos from BIOS
[ 173.749346] radeonfb: Reference=27.00 MHz (RefDiv=60) Memory=143.00 Mhz, System=143.00 MHz
[ 173.798982] radeonfb: PLL min 12000 max 35000
[ 173.929494] i2c_adapter i2c-1: unable to read EDID block.
[ 174.121356] i2c_adapter i2c-1: unable to read EDID block.
[ 174.313307] i2c_adapter i2c-1: unable to read EDID block.
[ 174.777182] i2c_adapter i2c-2: unable to read EDID block.
[ 174.969129] i2c_adapter i2c-2: unable to read EDID block.
[ 175.161078] i2c_adapter i2c-2: unable to read EDID block.
[ 175.315579] radeonfb: Monitor 1 type DFP found
[ 175.342278] radeonfb: EDID probed
[ 175.362230] radeonfb: Monitor 2 type CRT found
[ 176.420926] Console: switching to colour frame buffer device 128x48
[ 177.132991] radeonfb (0000:00:01.0): ATI Radeon QY
[ 177.164714] tridentfb: Trident framebuffer 0.7.8-NEWAPI initializing
[ 177.204778] hgafb: HGA card not detected.
[ 177.229089] hgafb: probe of hgafb.0 failed with error -22
[ 177.265581] vga16fb: mapped to 0xffff8100000a0000
[ 177.294281] fb1: VGA16 VGA frame buffer device
[ 177.323286] fb2: Virtual frame buffer device, using 1024K of video memory
[ 177.364610] ACPI: Power Button (FF) [PWRF]
[ 177.390051] ibm_acpi: ec object not found
[ 177.799265] Linux agpgart interface v0.101 (c) Dave Jones
[ 177.832901] ipmi message handler version 39.0
[ 177.859197] ipmi device interface
[ 177.879561] Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
[ 177.933667] Hangcheck[ 178.096225] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
[ 178.146934] loop: loaded (max 8 devices)
[ 178.170967] ibmasm: IBM ASM Service Processor Driver version 1.0 loaded
[ 178.211074] GSI 17 sharing vector 0xB1 and IRQ 17
[ 178.239566] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 18 (level, low) -> IRQ 17
[ 178.284872] 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
[ 178.284885] 0000:02:01.0: 3Com PCI 3c905C Tornado at ffffc20000042000.
[ 178.311834] tg3.c:v3.66 (September 23, 2006)
[ 178.311869] GSI 18 sharing vector 0xB9 and IRQ 18
[ 178.311879] ACPI: PCI Interrupt 0000:01:01.0[A] -> GSI 24 (level, low) -> IRQ 18
[ 178.452374] eth1: Tigon3 [partno(BCM95704A6) rev 2100 PHY(5704)] (PCIX:66MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:60:98:74:22
[ 178.452390] eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[1] TSOcap[0]
[ 178.452438] eth1: dma_rwctrl[769f0000] dma_mask[64-bit]
[ 178.453100] GSI 19 sharing vector 0xC1 and IRQ 19
[ 178.453115] ACPI: PCI Interrupt 0000:01:01.1[B] -> GSI 28 (level, low) -> IRQ 19
[ 178.619694] eth2: Tigon3 [partno(BCM95704A6) rev 2100 PHY(5704)] (PCIX:66MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:60:98:74:23
[ 178.619705] eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
[ 178.619709] eth2: dma_rwctrl[769f0000] dma_mask[64-bit]
[ 178.620480] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 178.620487] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 178.620586] SvrWks CSB6: IDE controller at PCI slot 0000:00:0f.1
[ 178.620612] SvrWks CSB6: chipset revision 160
[ 178.620615] SvrWks CSB6: not 100% native mode: will probe irqs later
[ 178.620640] ide0: BM-DMA at 0x0700-0x0707, BIOS settings: hda:DMA, hdb:DMA
[ 178.620661] SvrWks CSB6: simplex device: DMA disabled
[ 178.620664] ide1: SvrWks CSB6 Bus-Master DMA disabled (BIOS)
[ 179.370943] hda: HL-DT-STDVD-ROM GDR8082N, ATAPI CD/DVD-ROM drive
[ 179.715251] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 180.285934] hda: ATAPI 24X DVD-ROM drive, 256kB Cache
[ 180.306029] Uniform CD-ROM driver Revision: 3.20
[ 180.434132] usbmon: debugfs is not available
[ 180.502630] GSI 20 sharing vector 0xC9 and IRQ 20
[ 180.572766] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 180.660206] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 180.735266] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
[ 180.822372] ohci_hcd 0000:00:03.0: irq 20, io mem 0xf2c10000
[ 180.988387] usb usb1: Product: OHCI Host Controller
[ 181.060155] usb usb1: Manufacturer: Linux 2.6.18mx ohci_hcd
[ 181.136015] usb usb1: SerialNumber: 0000:00:03.0
[ 181.138365] usb usb1: configuration #1 chosen from 1 choice
[ 181.139014] hub 1-0:1.0: USB hub found
[ 181.139358] hub 1-0:1.0: 2 ports detected
[ 181.259512] ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 20 (level, low) -> IRQ 20
[ 181.414004] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 181.415193] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
[ 181.415233] ohci_hcd 0000:00:03.1: irq 20, io mem 0xf2c11000
[ 181.5092] usb usb2: Product: OHCI Host Controller
[ 181.504194] usb usb2: Manufacturer: Linux 2.6.18mx ohci_hcd
[ 181.504196] usb usb2: SerialNumber: 0000:00:03.1
[ 181.504232] usb usb2: uevent
[ 181.505151] usb usb2: usb_probe_device
[ 181.505960] usb usb2: configuration #1 chosen from 1 choice
[ 181.505980] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 181.506026] usb 2-0:1.0: uevent
[ 181.506261] hub 2-0:1.0: usb_probe_interface
[ 181.506267] hub 2-0:1.0: usb_probe_interface - got id
[ 181.506271] hub 2-0:1.0: USB hub found
[ 181.506300] hub 2-0:1.0: 2 ports detected
[ 181.506304] hub 2-0:1.0: standalone hub
[ 181.506307] hub 2-0:1.0: no power switching (usb 1.0)
[ 181.506310] hub 2-0:1.0: global over-current protection
[ 181.506314] hub 2-0:1.0: power on to power good time: 30ms
[ 181.506333] hub 2-0:1.0: local power source is good
[ 181.506337] hub 2-0:1.0: no over-current condition exists
[ 181.506342] hub 2-0:1.0: trying to enable port power on non-switchable hub
[ 181.613892] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 181.618715] USB Universal Host Controller Interface driver v3.0
Boot log with do_IRQ: cannot handle IRQ -1:
kernel (hd0,1)/boot/calgary/bzImage root=/dev/sda2 console=tty0 console=ttyS1,1
9200
[Linux-bzImage, setup=0x1c00, size=0x2e3ad8] initrd (hd0,1)/boot/calgary/aic94xxfw.initramfs.gz
[Linux-initrd @ 0x37e3f000, 0x1b01da bytes]
savedefault
[ 0.000000] Linux version 2.6.18mx (muli@rhun) (gcc version 3.4.1) #149 SMP Thu Oct 5 22:52:09 IST 2006
[ 0.000000] Command line: root=/dev/sda2 console=tty0 console=ttyS1,19200
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 0000000000099000 (usable) [ 0.000000] BIOS-e820: 0000000000099000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000e7f9c640 (usable)
[ 0.000000] BIOS-e820: 00000000e7f9c640 - 00000000e7fa6a40 (ACPI data)
[ 0.000000] BIOS-e820: 00000000e7fa6a40 - 00000000e8000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000198000000 (usable)
[ 0.000000] end_pfn_map = 1671168
[ 0.000000] DMI 2.3 present.
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1671168
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0 -> 153
[ 0.000000] 0: 256 -> 950172
[ 0.000000] 0: 1048576 -> 1671168
[ 0.000000] ACPI: PM-Timer IO Port: 0x9c
[ 0.000000] ACPI: LAPIC (acpirocessor #6
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x07] enabled)
[ 0.000000] Processor #7
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x0f] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 15, address 0xfec00000, GSI 0-35
[ 0.000000] ACPI: IOAPIC (id[0x0e] address[0xfec01000] gsi_base[35])
[ 0.000000] IOAPIC[1]: apic_id 14, address 0xfec01000, GSI 35-70
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 8 global_irq 8 low edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 low edge)
[ 0.000000] Setting APIC routing to flat
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Nosave address range: 0000000000099000 - 00000000000a0000
[ 0.000000] Nosave address range: 00000000000a0000 - 00000000000e0000
[ 0.000000] Nosave address range: 00000000000e0000 - 0000000000100000
[ 0.000000] Nosave address range: 00000000e7f9c000 - 00000000e7f9d000
[ 0.000000] Nosave address range: 00000000e7f9d000 - 00000000e7fa6000
[ 0.000000] Nosave address range: 00000000e7fa6000 - 00000000e7fa7000
[ 0.000000] Nosave address range: 00000000e7fa7000 - 00000000e8000000
[ 0.000000] No4 bytes of per cpu data
[ 0.000000] Built 1 zonelists. Total pages: 1534048
[ 0.000000] Kernel command line: root=/dev/sda2 console=tty0 console=ttyS1,19200
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 162.254679] Console: colour VGA+ 80x25
[ 164.190495] Lock dependency validator:752] ... MAX_LOCKDEP_ENTRIES: 8192
[ 164.366947] ... MAX_LOCKDEP_CHAINS: 8192
[ 164.393142] ... CHAINHASH_SIZE: 4096
[ 164.419339] memory used by lock dependency info: 1328 kB
[ 164.451778] per task-struct memory footprint: 1680 bytes
[ 164.491419] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 164.546385] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)[ 164.592804] Checking aperture...
[ 164.635185] PCI-DMA: Calgary IOMMU detected.
[ 164.660858] PCI-DMA: Calgary TCE table spec is 7, CONFIG_IOMMU_DEBUG is enabled.
[ 164.823121] Memory: 6096428k/6684672k available (3788k kernel code, 193716k reserved, 2726k data, 276k init)
[ 164.961480] Calibrating delay using timer specific routine.. 6346.50 BogoMIPS (lpj=12693003)
[ 165.012500] Mount-cache hash table entries: 256
[ 165.041360] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 165.072858] CPU: L2 cache: 1024K
[ 165.092254] using mwait in idle threads.
[ 165.115856] CPU: Physical Processor ID: 0
[ 165.139973] CPU: Processor Core ID: 0
[ 165.162031] CPU0: Thermal monitoring enabled (TM1)
[ 165.190818] Freeing SMP alternatives: 32k freed
[ 165.218068] ACPI: Core revision 20060707
[ 165.288939] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
[ 165.363991] Using local APIC timer interrupts.
[ 165.422216] result 10425729
[ 165.439044] Detected 10.425 MHz APIC timer.
[ 165.466518] lockdep: not fixing up alternatives.
[ 165.494795] Booting processor 1/4 APIC 0x1
[ 165.529811] Initializing CPU#1
[ 165.609305] Calibrating delay using timer specific routine.. 6339.08 BogoMIPS (lpj=12678178)
[ 165.609322] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 165.609325] CPU: L2 cache: 1024K
[ 165.609329] CPU: Physical Processor ID: 0
[ 165.609331] CPU: Processor Core ID: 0
[ 165.609344] CPU1: Thermal monitoring enabled (TM1)
[ 165.609624] Intel(R) Xeon(TM) MP CPU 3.16GHz stepping 01
[ 165.613632] lockdep: not fixing up alternatives.
[ 165.875688] Booting processor 2/4 APIC 0x6
[ 165.910707] Initializing CPU#2
[ 165.989208] Calibrating delay using timer specific routine.. 6339.23 BogoMIPS (lpj=12678478)
[ 165.989221] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 165.989224] CPU: L2 cache: 1024K
[ 165.989227] CPU: Physical Processor ID: 3
[ 165.989229] CP[ 166.290617] Initializing CPU#3
[ 166.369111] Calibrating delay using timer specific routine.. 6339.30 BogoMIPS (lpj=12678612)
[ 166.369125] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 166.369128] CPU: L2 cache: 1024K
[ 166.369132] CPU: Physical Processor ID: 3
[ 166.369133] CPU: Processor Core ID: 0
[ 166.369144] CPU3: Thermal monitoring enabled (TM1)
[ 166.369384] Intel(R) Pentium(R) 4 CPU 3.16GHz stepping 09
[ 166.373137] Brought up 4 CPUs
[ 166.625258] testing NMI watchdog ... OK.
[ 166.688965] time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
[ 166.726055] time.c: Detected 3169.440 MHz processor.
[ 167.084243] migration_cost=73,703
[ 167.105254] checking if image is initramfs... it is
[ 167.296623] Freeing initrd memory: 1728k freed
[ 167.326347] NET: Registered protocol family 16
[ 167.363464] ACPI: bus type pci registered
[ 167.387553] PCI: Using configuration type 1
[ 167.542434] ACPI: Interpreter enabled
[ 167.564437] ACPI: Using IOAPIC for interrupt routing
[ 167.600989] ACPI: PCI Root Bridge [VP00] (0000:00)
[ 167.633174] PCI: Ignoring BAR0-3 of IDE controller 0000:00:0f.1
[ 167.688862] ACPI: PCI Root Bridge [VP01] (0000:01)
[ 167.723077] ACPI: PCI Root Bridge [VP02] (0000:02)
[ 167.762081] ACPI: PCI Root Bridge [VP03] (0000:04)
[ 167.799356] ACPI: PCI Root Bridge [VP04] (0000:06)
[ 167.838090] ACPI: PCI Root Bridge [VP05] (0000:08)
[ 167.877162] ACPI: PCI Root Bridge [VP06] (0000:0a)
[ 167.915790] ACPI: PCI Root Bridge [VP07] (0000:0c)
[ 167.954746] SCSI subsystem initialized
[ 167.977515] usb, try "pci=routeirq". If it helps, post a report
[ 168.148438] PCI-DMA: Using Calgary IOMMU
[ 168.527814] Calgary: enabling translation on PHB 0
[ 168.556590] Calgary: errant DMAs will now be prevented on this bus.
[ 168.949497] Calgary: enabling translation on PHB 1
[ 168.978270] Calgary: errant DMAs will now be prevented on this bus.
[ 169.371449] Calgary: enabling translation on PHB 2
[ 169.400237] Calgary: errant DMAs will now be prevented on this bus.
[ 169.437927] PCI-GART: No AMD northbridge found.
[ 169.475527] NET: Registered protocol family 2
[ 169.556442] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 169.602331] TCP established hash table entries: 65536 (order: 9, 3670016 bytes)
[ 169.654323] TCP bind hash table entries: 32768 (order: 8, 1835008 bytes)
[ 169.697894] TCP: Hash tables configured (established 65536 bind 32768)
[ 169.737140] TCP reno registered
[ 169.778387] Total HugeTLB memory allocated, 0
[ 169.806340] Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
[ 169.845456] io scheduler noop registered
[ 169.869143] io scheduler anticip16
[ 170.031922] radeonfb: Found Intel x86 BIOS ROM Image
[ 170.076069] radeonfb: Retrieved PLL infos from BIOS
[ 170.105379] radeonfb: Reference=27.00 MHz (RefDiv=60) Memory=143.00 Mhz, System=143.00 MHz
[ 170.155008] radeonfb: PLL min 12000 max 35000
[ 170.289514] i2c_adapter i2c-1: unable to read EDID block.
[ 170.481376] i2c_adapter i2c-1: unable to read EDID block.
[ 170.673320] i2c_adapter i2c-1: unable to read EDID block.
[ 171.137184] i2c_adapter i2c-2: unable to read EDID block.
[ 171.329128] i2c_adapter i2c-2: unable to read EDID block.
[ 171.521072] i2c_adapter i2c-2: unable to read EDID block.
[ 171.675567] radeonfb: Monitor 1 type DFP found
[ 171.702256] radeonfb: EDID probed
[ 171.722209] radeonfb: Monitor 2 type CRT found
[ 172.780899] Console: switching to colour frame buffer device 128x48
[ 173.493268] radeonfb (0000:00:01.0): ATI Radeon QY
[ 173.526192] tridentfb: Trident framebuffer 0.7.8-NEWAPI initializing
[ 173.566008] hgafb: HGA card not detected.
[ 173.590340] hgafb: probe of hgafb.0 failed with error -22
[ 173.625574] vga16fb: mapped to 0xffff8100000a0000
[ 173.654233] fb1: VGA16 VGA frame buffer device
[ 173.682430] fb2: Virtual frame buffer device, using 1024K of video memory
[ 173.723852] ACPI: Power Button (FF) [PWRF]
[ 173.749277] ibm_acpi: ec object not found
[ 174.153281] Linux agpgart interface v0.101 (c) Dave Jones
[ 174.186181] ipmi message handler version 39.0
[ 174.212487] ipmi device interface
[ 174.212704] Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
[ 174.212708] Hangcheck: Using monotonic_clock().
[ 174.212714] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 174.215329] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 174.232727] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 174.248340] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
[ 174.253979] loop: loaded (max 8 devices)
[ 174.254880] ibmasm: IBM ASM Service Processor Driver version 1.0 loaded
[ 174.255602] GSI 17 sharing vector 0xB1 and IRQ 17
[ 174.255614] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 18 (level, low) -> IRQ 17
[ 174.434473] 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
[ 174.434486] 0000:02:01.0: 3Com PCI 3c905C Tornado at ffffc20000042000.
[ 174.458336] tg3.c:v3.66 (September 23, 2006)
[ 174.458371] GSI 18 sharing vector 0xB9 and IRQ 18
[ 174.458382] ACPI: PCI Interrupt 0000:01:01.0[A] -> GSI 24 (level, low) -> IRQ 18
[ 174.651645] eth1: Tigon3 [partno(BCM95704A6) rev 2100 PHY(5704)] (PCIX:66MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:60:98:74:22
[ 174.651657] eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[1] TSOcap[0]
[ 174.651661] eth1: dma_rwctrl[769f0000] dma_mask[64-bit]
[ 174.651742] GSI 19 sharing vector 0xC1 and IRQ 19
[ 174.651751] ACPI: PCI Interrupt 0000:01:01.1[B] -> GSI 28 (level, low) -> IRQ 19
[ 174.947630] eth2: Tigon3 [partno(BCM95704A6) rev 2100 PHY(5704)] (PCIX:66MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:60:98:74:23
[ 174.947641] eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
[ 174.947645] eth2: dma_rwctrl[769f0000] dma_mask[64-bit]
[ 174.948361] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 174.948368] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 174.948462] SvrWks CSB6: IDE controller at PCI slot 0000:00:0f.1
[ 174.948490] SvrWks CSB6: chipset revision 160
[ 174.948492] SvrWks CSB6: not 100% native mode: will probe irqs later
[ 174.948521] ide0: BM-DMA at 0x0700-0x0707, BIOS settings: hda:DMA, hdb:DMA
[ 174.948547] SvrWks CSB6: simplex device: DMA disabled
[ 174.948549] ide1: SvrWks CSB6 Bus-Master DMA disabled (BIOS)
[ 175.686861] hda: HL-DT-STDVD-ROM GDR8082N, ATAPI CD/DVD-ROM drive
[ 176.027298] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 176.598782] hda: ATAPI 24X DVD-ROM drive, 256kB Cache
[ 176.614367] Uniform CD-ROM driver Revision: 3.20
[ 176.742904] usbmon: debugfs is not available
[ 176.810874] GSI 20 sharing vector 0xC9 and IRQ 20
[ 176.880745] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 176.967527] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 177.042503] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
[ 177.129180] ohci_hcd 0000:00:03.0: irq 20, io mem 0xf2c10000
[ 177.292284] usb usb1: Product: OHCI Host Controller
[ 177.363518] usb usb1: Manufacturer: Linux 2.6.18mx ohci_hcd
[ 177.438777] usb usb1: SerialNumber: 0000:00:03.0
[ 177.508765] usb usb1: configuration #1 chosen from 1 choice
[ 177.584638] hub 1-0:1.0: USB hub found
[ 177.648464] hub 1-0:1.0: 2 ports detected
[ 177.819436] ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 20 (level, low) -> IRQ 20
[ 177.905381] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 177.977460] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
[ 178.062963] ohci_hcd 0000:00:03.1: irq 20, io mem 0xf2c11000
[ 178.223789] usb usb2: Product: OHCI Host Controller
[ 178.292928] usb usb2: Manufacturer: Linux 2.6.18mx ohci_hcd
[ 178.366239] usb usb2: SerialNumber: 0000:00:03.1
[ 178.367676] usb usb2: configuration #1 chosen from 1 choice
[ 178.368738] hub 2-0:1.0: USB hub found
[ 178.368756] hub 2-0:1.0: 2 ports detected
[ 178.7147] USB Universal Host Controller Interface driver v3.0
[ 178.639733] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 178.639821] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 178.685603] mice: PS/2 mouse device common for all mice
[ 178.705241] input: PC Speaker as /class/input/input0
[ 178.716390] input: AT Translated Set 2 keyboard as /class/input/input1
[ 178.725625] i2c /dev entries driver
[ 178.738285] i2c-parport: adapter type unspecified
[ 178.943983] i2c_adapter i2c-9191: Driver w83781d-isa failed to attach adapter, unregistering
[ 178.953019] i2c_adapter i2c-9191: Driver lm78-isa failed to attach adapter, unregistering
[ 178.959829] md: linear personality registered for level -1
[ 178.959836] md: raid0 personality registered for level 0
[ 178.959842] md: raid1 personality registered for level 1
[ 178.959847] md: multipath personality registered for level -4
[ 179.008855] IBM TrackPoint firmware: 0x0b, buttons: 3/3
[ 179.024974] input: TPPS/2 IBM TrackPoint as /class/input/input2
[ 179.789256] device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: dm-devel@xxxxxxxxxx
[ 179.874553] device-mapper: multipath: version 1.0.5 loaded
[ 179.941863] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 180.014917] device-mapper: multipath emc: version 0.0.3 loaded
[ 180.083798] EDAC MC: Ver: 2.0.1 Oct 5 2006
[ 180.143574] pktgen v2.68: Packet Generator for packet performance testing.
[ 180.219216] u32 classifier
[ 180.269850] OLD policer on
[ 180.323042] IPv4 over IPv4 tunneling driver
[ 180.382659] GRE over IPv4 tunneling driver
[ 180.441335] TCP cubic registered
[ 180.494834] Initializing XFRM netlink socket
[ 180.554246] NET: Registered protocol family 1
[ 180.554260] NET: Registered protocol family 17
[ 180.554309] NET: Registered protocol family 15
[ 180.730291] 802.1Q VLAN Support v1.8 Ben Greear <greearb@xxxxxxxxxxxxxxx>
[ 180.802601] All bugs added by David S. Miller <davem@xxxxxxxxxx>
[ 180.905733] SCTP: Hash tables configured (established 37449 bind 37449)
[ 180.978800] Freeing unused kernel memory: 276k freed
running (1:0) /[ 181.050177] do_IRQ: cannot handle IRQ -1
[ 181.105984] ----------- [cut here ] --------- [please bite here ] ---------
[ 181.180286] Kernel BUG at ...uli/w/iommu/calgary/linux/arch/x86_64/kernel/irq.c:118
[ 181.258051] invalid opcode: 0000 [1] SMP
[ 181.279092] CPU 1
[ 181.279094] Modules linked in:
[ 181.279098] Pid: 0, comm: swapper Not tainted 2.6.18mx #149
[ 181.279101] RIP: 0010:[<ffffffff8020c792>]
lspci:
0000:00:00.0 Host bridge: IBM: Unknown device 02a1 (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 240
Capabilities: [60] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=1
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
0000:00:01.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE] (prog-if 00 [VGA])
Subsystem: IBM: Unknown device 02c8
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (2000ns min), cache line size 10
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 1800 [size=256]
Region 2: Memory at f2c00000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:03.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation USB
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (250ns min, 10500ns max), cache line size 10
Interrupt: pin A routed to IRQ 20
Region 0: Memory at f2c10000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:03.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation USB
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (250ns min, 10500ns max), cache line size 10
Interrupt: pin B routed to IRQ 20
Region 0: Memory at f2c11000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:03.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (4000ns min, 8500ns max), cache line size 20
Interrupt: pin C routed to IRQ 20
Region 0: Memory at f2c12000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0f.0 Host bridge: ServerWorks CSB6 South Bridge (rev a0)
Subsystem: ServerWorks: Unknown device 0201
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240
0000:00:0f.1 IDE interface: ServerWorks CSB6 RAID/IDE Controller (rev a0) (prog-if 82 [Master PriP])
Subsystem: ServerWorks: Unknown device 0212
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at 0700 [size=16]
0000:00:0f.3 ISA bridge: ServerWorks GCLE-2 Host Bridge
Subsystem: ServerWorks: Unknown device 0230
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:01:00.0 Host bridge: IBM: Unknown device 02a1 (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 240
Capabilities: [60] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=1
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
0000:01:01.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 10)
Subsystem: IBM: Unknown device 02e7
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (16000ns min), cache line size 10
Interrupt: pin A routed to IRQ 24
Region 0: Memory at f2dc0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: 8e9e3fb7523479b4 Data: b19f
0000:01:01.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 10)
Subsystem: IBM: Unknown device 02e7
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (16000ns min), cache line size 10
Interrupt: pin B routed to IRQ 28
Region 0: Memory at f2dd0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: cffdfff793f7fddc Data: d6f7
0000:01:02.0 SCSI storage controller: Adaptec: Unknown device 041e (rev 08)
Subsystem: IBM: Unknown device 02e7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (32000ns min, 26750ns max), cache line size 10
Interrupt: pin A routed to IRQ 25
Region 0: Memory at f2d80000 (64-bit, non-prefetchable) [size=256K]
Region 2: Memory at f1400000 (64-bit, prefetchable) [size=128K]
Region 4: I/O ports at 2000 [size=256]
Capabilities: [40] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=3 OST=4
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- Capabilities: [58] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [e0] Message Signalled Interrupts: 64bit+ Queue=0/2 Enable-
Address: 0000000000000000 Data: 0000
0000:02:00.0 Host bridge: IBM: Unknown device 02a1 (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 240
Capabilities: [60] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=1
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
0000:02:01.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 6c)
Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management NIC
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (2500ns min, 2500ns max), cache line size 10
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 2800 [size=128]
Region 1: Memory at f2e20000 (32-bit, non-prefetchable) [size=128]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:04:00.0 Host bridge: IBM: Unknown device 02a1 (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 240
Capabilities: [60] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=1
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
0000:06:00.0 Host bridge: IBM: Unknown device 02a1 (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 240
Capabilities: [60] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=1
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
0000:08:00.0 Host bridge: IBM: Unknown device 02a1 (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 240
Capabilities: [60] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=1
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
0000:0a:00.0 Host bridge: IBM: Unknown device 02a1 (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 240
Capabilities: [60] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=1
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
0000:0c:00.0 Host bridge: IBM: Unknown device 02a1 (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 240
Capabilities: [60] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=1
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
Cheers,
Muli
Attachment:
config.gz
Description: application/gunzip