Nvidia MCP55 Machine reboots on ixgb driver load
From: Roger Heflin
Date: Wed Jan 24 2007 - 16:20:47 EST
Hello,
I have a machine (actually 2 machines) that upon loading
the intel 10GBe driver (ixgb) the machine reboots, I am
using a RHAS4.4 based distribution with Vanilla 2.6.19.2
(the RHAS 4.4.03 kernel also reboots with the ixgb load),
I don't see any messages on the machine before it reboots,
loading the driver with debug does not appear to produce
any extra messages. The basic steps are the I load
the driver, the machine locks up, and then in a second
or 2 it starts to post.
I have tried the default ixgb driver in 2.6.19.2, and I
have tried the open source intel driver on RH4.4, both cause
the same reboot. I also tried the linux firmware
development kit, and booting fc6 causes the same reboot
upon the network driver load.
I have tried pci=nomsi, noacpi, noapic, acpi=off, and a
few others with the results staying the same. I have also
tried various bios settings with no changes, the bios
in the machine is the latest, a beta bios has similar results,
I am talking to the MB vendor about the issue.
I have 2 of the intel boards and they both appear to produce
this behavior with this type of motherboard, with a different
motherboard (different chipset) they appear to at least
load the driver without killing the machine work correctly.
dmesg and lspci, and lspci -vv, interrupts, and iomem follow.
I suspect that it is a bios issue, and that there may not
be a way around it, except for fixing the bios.
The machine is a dual-dual core opteron, with an nvidia
MCP55 chipset. The intel card is pci-x. I have tried
it with only the intel card and the lsi megaraid card required
for it to boot and the same reboot happens.
What sort of bad behavior would cause this sort of reboot?
Also note that the linux.nics@xxxxxxxxx address is apparently
unused and returns an email telling you to use a web page,
and so far after using the web page I have not got any response
indicating that anything got to anyone.
Roger
00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2)
00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3)
00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3)
00:01.2 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a3)
00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1)
00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2)
00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2)
00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3)
00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3)
00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02)
02:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X
Bridge (rev 07)
02:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X
Bridge (rev 07)
03:04.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID (rev 01)
03:06.0 Fibre Channel: LSI Logic / Symbios Logic FC949X Fibre Channel
Adapter (rev 01)
03:06.1 Fibre Channel: LSI Logic / Symbios Logic FC949X Fibre Channel
Adapter (rev 01)
04:07.0 Ethernet controller: Intel Corporation 82597EX 10GbE Ethernet
Controller (rev 02)
08:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI
Express-to-PCI Bridge (rev 03)
09:02.0 FireWire (IEEE 1394): Texas Instruments TSB82AA2 IEEE-1394b Link
Layer Controller (rev 01)
Linux version 2.6.19.2 (root@xxxxxxxxxxxxxxxxxxxx) (gcc version 3.4.6
20060404 (Red Hat 3.4.6-3)) #2 SMP Wed Jan 24 09:31:05 EST 2007
Command line: ro root=/dev/BootDisk/root elevator=deadline pci=routeirq
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000dfff0000 (usable)
BIOS-e820: 00000000dfff0000 - 00000000dfffe000 (ACPI data)
BIOS-e820: 00000000dfffe000 - 00000000e0000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 917488) 1 entries of 3200 used
Entering add_active_range(0, 1048576, 1179648) 2 entries of 3200 used
end_pfn_map = 1179648
DMI present.
ACPI: RSDP (v002 ACPIAM ) @
0x00000000000f8540
ACPI: XSDT (v001 A M I OEMXSDT 0x11000628 MSFT 0x00000097) @
0x00000000dfff0100
ACPI: FADT (v003 A M I OEMFACP 0x11000628 MSFT 0x00000097) @
0x00000000dfff0290
ACPI: MADT (v001 A M I OEMAPIC 0x11000628 MSFT 0x00000097) @
0x00000000dfff0390
ACPI: OEMB (v001 A M I AMI_OEM 0x11000628 MSFT 0x00000097) @
0x00000000dfffe040
ACPI: HPET (v001 A M I OEMHPET0 0x11000628 MSFT 0x00000097) @
0x00000000dfff53d0
ACPI: SRAT (v001 AMD HAMMER 0x00000001 AMD 0x00000001) @
0x00000000dfff5410
ACPI: SSDT (v001 A M I POWERNOW 0x00000001 AMD 0x00000001) @
0x00000000dfff5520
ACPI: DSDT (v001 H8DM8 H8DM8000 0x00000000 INTL 0x20051117) @
0x0000000000000000
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: PXM 0 -> APIC 1 -> Node 0
SRAT: PXM 1 -> APIC 2 -> Node 1
SRAT: PXM 1 -> APIC 3 -> Node 1
SRAT: Node 0 PXM 0 0-a0000
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
SRAT: Node 0 PXM 0 0-80000000
Entering add_active_range(0, 0, 159) 1 entries of 3200 used
Entering add_active_range(0, 256, 524288) 1 entries of 3200 used
SRAT: Node 1 PXM 1 80000000-e0000000
Entering add_active_range(1, 524288, 917488) 2 entries of 3200 used
SRAT: Node 1 PXM 1 80000000-120000000
Entering add_active_range(1, 524288, 917488) 3 entries of 3200 used
Entering add_active_range(1, 1048576, 1179648) 3 entries of 3200 used
NUMA: Using 31 for the hash shift.
Bootmem setup node 0 0000000000000000-0000000080000000
Bootmem setup node 1 0000000080000000-0000000120000000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1179648
early_node_map[4] active PFN ranges
0: 0 -> 159
0: 256 -> 524288
1: 524288 -> 917488
1: 1048576 -> 1179648
On node 0 totalpages: 524191
DMA zone: 64 pages used for memmap
DMA zone: 1079 pages reserved
DMA zone: 2856 pages, LIFO batch:0
DMA32 zone: 8128 pages used for memmap
DMA32 zone: 512064 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
On node 1 totalpages: 524272
DMA zone: 0 pages used for memmap
DMA32 zone: 8192 pages used for memmap
DMA32 zone: 385008 pages, LIFO batch:31
Normal zone: 2048 pages used for memmap
Normal zone: 129024 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x2008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
Processor #2
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
Processor #3
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x10de8201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009f000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000e0000
Nosave address range: 00000000000e0000 - 0000000000100000
Nosave address range: 00000000dfff0000 - 00000000dfffe000
Nosave address range: 00000000dfffe000 - 00000000e0000000
Nosave address range: 00000000e0000000 - 00000000fec00000
Nosave address range: 00000000fec00000 - 00000000fec01000
Nosave address range: 00000000fec01000 - 00000000fee00000
Nosave address range: 00000000fee00000 - 00000000fef00000
Nosave address range: 00000000fef00000 - 00000000ff700000
Nosave address range: 00000000ff700000 - 0000000100000000
Allocating PCI resources starting at e2000000 (gap: e0000000:1ec00000)
PERCPU: Allocating 34048 bytes of per cpu data
Built 2 zonelists. Total pages: 1028952
Kernel command line: ro root=/dev/BootDisk/root elevator=deadline
pci=routeirq
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
CPU 0: aperture @ 4000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
Memory: 4042040k/4718592k available (2264k kernel code, 151812k
reserved, 989k data, 324k init)
Calibrating delay using timer specific routine.. 4427.57 BogoMIPS
(lpj=8855158)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Freeing SMP alternatives: 24k freed
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 12566127
Detected 12.566 MHz APIC timer.
Booting processor 1/4 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4422.74 BogoMIPS
(lpj=8845495)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Dual-Core AMD Opteron(tm) Processor 2214 stepping 02
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff -5 cycles, maxerr 622 cycles)
Booting processor 2/4 APIC 0x2
Initializing CPU#2
Calibrating delay using timer specific routine.. 4422.75 BogoMIPS
(lpj=8845518)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 2/2 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
Dual-Core AMD Opteron(tm) Processor 2214 stepping 02
CPU 2: Syncing TSC to CPU 0.
CPU 2: synchronized TSC with CPU 0 (last diff 113 cycles, maxerr 1138
cycles)
Booting processor 3/4 APIC 0x3
Initializing CPU#3
Calibrating delay using timer specific routine.. 4422.75 BogoMIPS
(lpj=8845518)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 3/3 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
Dual-Core AMD Opteron(tm) Processor 2214 stepping 02
CPU 3: Syncing TSC to CPU 0.
CPU 3: synchronized TSC with CPU 0 (last diff -8 cycles, maxerr 1140 cycles)
Brought up 4 CPUs
testing NMI watchdog ... OK.
time.c: Using 25.000000 MHz WALL HPET GTOD HPET timer.
time.c: Detected 2211.638 MHz processor.
migration_cost=305,385
checking if image is initramfs... it is
Freeing initrd memory: 1702k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:05.0
PCI: Transparent bridge - 0000:00:06.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR10._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR13._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR14._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR15.BR30._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR15.BR31._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *14
ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *5
ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *14
ACPI: PCI Interrupt Link [LMAD] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *7
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *5
ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LSA2] (IRQs 20 21 22 23) *0, disabled.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: Routing PCI interrupts for all devices because "pci=routeirq" specified
ACPI: PCI Interrupt Link [LSMB] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:01.1[A] -> Link [LSMB] -> GSI 23 (level,
low) -> IRQ 23
ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUB0] -> GSI 22 (level,
low) -> IRQ 22
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 21 (level,
low) -> IRQ 21
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LMAC] -> GSI 20 (level,
low) -> IRQ 20
ACPI: PCI Interrupt Link [LMAD] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LMAD] -> GSI 23 (level,
low) -> IRQ 23
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 19
ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNKA] -> GSI 19 (level,
low) -> IRQ 19
ACPI: PCI Interrupt Link [LNEC] enabled at IRQ 18
ACPI: PCI Interrupt 0000:03:04.0[A] -> Link [LNEC] -> GSI 18 (level,
low) -> IRQ 18
ACPI: PCI Interrupt Link [LNEA] enabled at IRQ 17
ACPI: PCI Interrupt 0000:03:06.0[A] -> Link [LNEA] -> GSI 17 (level,
low) -> IRQ 17
ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 16
ACPI: PCI Interrupt 0000:03:06.1[B] -> Link [LNEB] -> GSI 16 (level,
low) -> IRQ 16
ACPI: PCI Interrupt 0000:04:07.0[A] -> Link [LNEB] -> GSI 16 (level,
low) -> IRQ 16
ACPI: PCI Interrupt 0000:09:02.0[A] -> Link [LNEA] -> GSI 17 (level,
low) -> IRQ 17
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ 4000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
PCI: Bridge: 0000:00:06.0
IO window: b000-bfff
MEM window: fe600000-fe6fffff
PREFETCH window: f0000000-f7ffffff
PCI: Bridge: 0000:02:00.0
IO window: c000-dfff
MEM window: fe700000-fe9fffff
PREFETCH window: fdf00000-fdffffff
PCI: Bridge: 0000:02:00.1
IO window: e000-efff
MEM window: fea00000-feafffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0a.0
IO window: c000-efff
MEM window: fe700000-feafffff
PREFETCH window: fdf00000-fdffffff
PCI: Bridge: 0000:00:0b.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:08:00.0
IO window: disabled.
MEM window: feb00000-febfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
IO window: disabled.
MEM window: feb00000-febfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0f.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:06.0 to 64
PCI: Setting latency timer of device 0000:00:0a.0 to 64
PCI: Setting latency timer of device 0000:02:00.0 to 64
PCI: Setting latency timer of device 0000:02:00.1 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
PCI: Setting latency timer of device 0000:08:00.0 to 64
PCI: Setting latency timer of device 0000:00:0f.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 131072 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 9, 2097152 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1169640729.984:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
[drm] Initialized drm 1.0.1 20051102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbmon: debugfs is not available
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 4 Dual-Core AMD Opteron(tm) Processor 2214 processors
(version 2.00.00)
powernow-k8: 0 : fid 0xe (2200 MHz), vid 0xa
powernow-k8: 1 : fid 0xc (2000 MHz), vid 0xc
powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xe
powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12
powernow-k8: 0 : fid 0xe (2200 MHz), vid 0xa
powernow-k8: 1 : fid 0xc (2000 MHz), vid 0xc
powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xe
powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12
Freeing unused kernel memory: 324k freed
SCSI subsystem initialized
Fusion MPT base driver 3.04.02
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT FC Host driver 3.04.02
ACPI: PCI Interrupt 0000:03:06.0[A] -> Link [LNEA] -> GSI 17 (level,
low) -> IRQ 17
mptbase: Initiating ioc0 bringup
input: AT Translated Set 2 keyboard as /class/input/input0
logips2pp: Detected unknown logitech mouse model 1
ioc0: FC949X: Capabilities={Initiator,Target,LAN}
input: PS/2 Logitech Mouse as /class/input/input1
scsi0 : ioc0: LSIFC949X, FwRev=01030200h, Ports=1, MaxQ=1023, IRQ=17
ACPI: PCI Interrupt 0000:03:06.1[B] -> Link [LNEB] -> GSI 16 (level,
low) -> IRQ 16
mptbase: Initiating ioc1 bringup
ioc1: FC949X: Capabilities={Initiator,Target,LAN}
scsi 0:0:0:0: Direct-Access RaidCtrl In Band Device R001 PQ: 1 ANSI: 5
scsi1 : ioc1: LSIFC949X, FwRev=01030200h, Ports=1, MaxQ=1023, IRQ=16
scsi 0:0:0:11: Direct-Access YI-16SA2 array1-top R001 PQ: 0
ANSI: 5
sda : very big device. try to use READ CAPACITY(16).
SCSI device sda: 8789059584 512-byte hdwr sectors (4499999 MB)
sda: Write Protect is off
sda: Mode Sense: bf 00 00 08
SCSI device sda: drive cache: write back
sda : very big device. try to use READ CAPACITY(16).
SCSI device sda: 8789059584 512-byte hdwr sectors (4499999 MB)
sda: Write Protect is off
sda: Mode Sense: bf 00 00 08
scsi 1:0:0:0: Direct-Access RaidCtrl In Band Device R001 PQ: 1 ANSI: 5
SCSI device sda: drive cache: write back
sda: unknown partition table
scsi 1:0:0:11: Direct-Access YI-16SA2 array1-top R001 PQ: 0
ANSI: 5
sdb : very big device. try to use READ CAPACITY(16).
SCSI device sdb: 8789059584 512-byte hdwr sectors (4499999 MB)
sd 0:0:0:11: Attached scsi disk sda
sdb: Write Protect is off
sdb: Mode Sense: bf 00 00 08
SCSI device sdb: drive cache: write back
sdb : very big device. try to use READ CAPACITY(16).
SCSI device sdb: 8789059584 512-byte hdwr sectors (4499999 MB)
sdb: Write Protect is off
sdb: Mode Sense: bf 00 00 08
SCSI device sdb: drive cache: write back
sdb:<5>scsi 0:0:1:0: Direct-Access RaidCtrl In Band Device R001
PQ: 1 ANSI: 5
unknown partition table
sd 1:0:0:11: Attached scsi disk sdb
scsi 0:0:1:12: Direct-Access YI-16SA2 array1-bottom R001 PQ: 0
ANSI: 5
scsi 1:0:1:0: Direct-Access RaidCtrl In Band Device R001 PQ: 1 ANSI: 5
sdc : very big device. try to use READ CAPACITY(16).
SCSI device sdc: 8789059584 512-byte hdwr sectors (4499999 MB)
sdc: Write Protect is off
sdc: Mode Sense: bf 00 00 08
SCSI device sdc: drive cache: write back
sdc : very big device. try to use READ CAPACITY(16).
SCSI device sdc: 8789059584 512-byte hdwr sectors (4499999 MB)
sdc: Write Protect is off
sdc: Mode Sense: bf 00 00 08
SCSI device sdc: drive cache: write back
sdc: unknown partition table
sd 0:0:1:12: Attached scsi disk sdc
scsi 1:0:1:12: Direct-Access YI-16SA2 array1-bottom R001 PQ: 0
ANSI: 5
Fusion MPT SPI Host driver 3.04.02
sdd : very big device. try to use READ CAPACITY(16).
SCSI device sdd: 8789059584 512-byte hdwr sectors (4499999 MB)
sdd: Write Protect is off
sdd: Mode Sense: bf 00 00 08
SCSI device sdd: drive cache: write back
sdd : very big device. try to use READ CAPACITY(16).
SCSI device sdd: 8789059584 512-byte hdwr sectors (4499999 MB)
sdd: Write Protect is off
sdd: Mode Sense: bf 00 00 08
SCSI device sdd: drive cache: write back
sdd: unknown partition table
sd 1:0:1:12: Attached scsi disk sdd
Fusion MPT SAS Host driver 3.04.02
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.4.9 (Release Date: Sun Jul 16 12:27:22 EST 2006)
megaraid: probe new device 0x1000:0x1960:0x1000:0x0520: bus 3:slot 4:func 0
ACPI: PCI Interrupt 0000:03:04.0[A] -> Link [LNEC] -> GSI 18 (level,
low) -> IRQ 18
megaraid: fw version:[1L45] bios version:[G121]
scsi2 : LSI Logic MegaRAID driver
scsi[2]: scanning scsi channel 0 [Phy 0] for non-raid devices
scsi 2:0:8:0: Processor SUPER GEM359 REV001 1.09 PQ: 0 ANSI: 2
scsi[2]: scanning scsi channel 1 [virtual] for logical drives
scsi 2:1:0:0: Direct-Access MegaRAID LD 0 RAID1 69G 1L45 PQ: 0 ANSI: 2
SCSI device sde: 142577664 512-byte hdwr sectors (73000 MB)
sde: Write Protect is off
sde: Mode Sense: 00 00 00 00
sde: asking for cache data failed
sde: assuming drive cache: write through
SCSI device sde: 142577664 512-byte hdwr sectors (73000 MB)
sde: Write Protect is off
sde: Mode Sense: 00 00 00 00
sde: asking for cache data failed
sde: assuming drive cache: write through
sde: sde1 sde2
sd 2:1:0:0: Attached scsi disk sde
device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised:
dm-devel@xxxxxxxxxx
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1169640738.476:2): selinux=0 auid=4294967295
scsi 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Attached scsi generic sg1 type 0
sd 0:0:0:11: Attached scsi generic sg2 type 0
scsi 0:0:1:0: Attached scsi generic sg3 type 0
sd 1:0:0:11: Attached scsi generic sg4 type 0
scsi 1:0:1:0: Attached scsi generic sg5 type 0
sd 0:0:1:12: Attached scsi generic sg6 type 0
sd 1:0:1:12: Attached scsi generic sg7 type 0
scsi 2:0:8:0: Attached scsi generic sg8 type 3
sd 2:1:0:0: Attached scsi generic sg9 type 0
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.57.
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LMAC] -> GSI 20 (level,
low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:08.0 to 64
forcedeth: using HIGHDMA
eth0: forcedeth.c: subsystem: 015d9:1611 bound to 0000:00:08.0
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LMAD] -> GSI 23 (level,
low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:09.0 to 64
forcedeth: using HIGHDMA
eth1: forcedeth.c: subsystem: 015d9:1611 bound to 0000:00:09.0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x2d00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x2e00
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 21 (level,
low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 21, io mem 0xfe5fac00
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUB0] -> GSI 22 (level,
low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 22, io mem 0xfe5fb000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
usb 1-10: new high speed USB device using ehci_hcd and address 2
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
usb 1-10: configuration #1 chosen from 1 choice
input: Peppercon AG Multidevice as /class/input/input2
input: USB HID v1.01 Mouse [Peppercon AG Multidevice] on usb-0000:00:02.1-10
input: Peppercon AG Multidevice as /class/input/input3
input: USB HID v1.01 Keyboard [Peppercon AG Multidevice] on
usb-0000:00:02.1-10
Initializing USB Mass Storage driver...
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
scsi 3:0:0:0: Direct-Access PepperC Virtual Disc 1 0.01 PQ: 0 ANSI: 3
sd 3:0:0:0: Attached scsi removable disk sdf
sd 3:0:0:0: Attached scsi generic sg10 type 0
usb-storage: device scan complete
EXT3 FS on dm-0, internal journal
device-mapper: multipath: version 1.0.5 loaded
device-mapper: multipath round-robin: version 1.0.0 loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS on sde1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SGI XFS with ACLs, security attributes, large block/inode numbers, no
debug enabled
SGI XFS Quota Management subsystem
Filesystem "dm-8": Disabling barriers, not supported by the underlying
device
XFS mounting filesystem dm-8
Ending clean XFS mount for filesystem: dm-8
Adding 8388600k swap on /dev/BootDisk/swap. Priority:-1 extents:1
across:8388600k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
hald[4193]: segfault at 00007fffcec0b000 rip 00000038d34708fa rsp
00007fffcec096f8 error 6
eth0: no IPv6 routers present
mtrr: type mismatch for f0000000,1000000 old: write-back new:
write-combining
00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2)
Subsystem: Super Micro Computer Inc: Unknown device 1611
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=3
IsocEn- LSEn+ ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit
DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn-
LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 1.0GHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+
800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz-
800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF-
RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [dc] HyperTransport: MSI Mapping
00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3)
Subsystem: Super Micro Computer Inc: Unknown device 1611
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3)
Subsystem: Super Micro Computer Inc: Unknown device 1611
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at ac00 [size=64]
Region 4: I/O ports at 2d00 [size=64]
Region 5: I/O ports at 2e00 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.2 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a3)
Subsystem: Super Micro Computer Inc: Unknown device 1611
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1)
(prog-if 10 [OHCI])
Subsystem: Super Micro Computer Inc: Unknown device 1611
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fe5fb000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2)
(prog-if 20 [EHCI])
Subsystem: Super Micro Computer Inc: Unknown device 1611
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at fe5fac00 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2)
(prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fe600000-fe6fffff
Prefetchable memory behind bridge: f0000000-f7ffffff
Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [b8] #0d [0000]
Capabilities: [8c] HyperTransport: MSI Mapping
00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3)
Subsystem: Super Micro Computer Inc: Unknown device 1611
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fe5f9000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at a480 [size=8]
Region 2: Memory at fe5fa800 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at fe5fa400 (32-bit, non-prefetchable) [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
Capabilities: [70] MSI-X: Enable+ Mask- TabSize=8
Vector table: BAR=2 offset=00000000
PBA: BAR=3 offset=00000000
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] HyperTransport: MSI Mapping
00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3)
Subsystem: Super Micro Computer Inc: Unknown device 1611
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fe5f8000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at a400 [size=8]
Region 2: Memory at fe5fa000 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at fe5f7c00 (32-bit, non-prefetchable) [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] MSI-X: Enable- Mask- TabSize=8
Vector table: BAR=2 offset=00000000
PBA: BAR=3 offset=00000000
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] HyperTransport: MSI Mapping
00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=02, subordinate=04, sec-latency=0
I/O behind bridge: 0000c000-0000efff
Memory behind bridge: fe700000-feafffff
Prefetchable memory behind bridge: 00000000fdf00000-00000000fdf00000
Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 5
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
(prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x0, ASPM L0s L1, Port 4
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
(prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x0, ASPM L0s L1, Port 3
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
(prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 2
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
(prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=08, subordinate=09, sec-latency=0
Memory behind bridge: feb00000-febfffff
Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 1
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
(prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=0
Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 0
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [a0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [c0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Capabilities: [f0] #0f [0010]
00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [a0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [c0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
Revision ID: 1.02
00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Capabilities: [f0] #0f [0010]
01:05.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02)
(prog-if 00 [VGA])
Subsystem: Super Micro Computer Inc: Unknown device 1611
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at b000 [size=256]
Region 2: Memory at fe6f0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fe600000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X
Bridge (rev 07) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=02, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 0000c000-0000dfff
Memory behind bridge: fe700000-fe9fffff
Prefetchable memory behind bridge: 00000000fdf00000-00000000fdf00000
Secondary status: 66Mhz+ FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 0
Link: Latency L0s <4us, L1 <16us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [54] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-, SRD- Freq=0
Status: Bus=2 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, SCO-, SRD-
: Upstream: Capacity=32, Commitment Limit=32
: Downstream: Capacity=16, Commitment Limit=16
Capabilities: [64] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=55mA
PME(D0+,D1+,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
02:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X
Bridge (rev 07) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=02, secondary=04, subordinate=04, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fea00000-feafffff
Secondary status: 66Mhz+ FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 0
Link: Latency L0s <4us, L1 <16us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [54] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-, SRD- Freq=3
Status: Bus=2 Dev=0 Func=1 64bit- 133MHz- SCD- USC-, SCO-, SRD-
: Upstream: Capacity=32, Commitment Limit=32
: Downstream: Capacity=16, Commitment Limit=16
Capabilities: [64] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=55mA
PME(D0+,D1+,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
03:04.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID (rev 01)
Subsystem: LSI Logic / Symbios Logic MegaRAID 520 SCSI 320-1 Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 10
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fdff0000 (32-bit, prefetchable) [size=64K]
Expansion ROM at fe9f0000 [disabled] [size=64K]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
03:06.0 Fibre Channel: LSI Logic / Symbios Logic FC949X Fibre Channel
Adapter (rev 01)
Subsystem: LSI Logic / Symbios Logic: Unknown device 1100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 72 (16000ns min, 2500ns max), Cache Line Size 10
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at d000 [disabled] [size=256]
Region 1: Memory at fe9ec000 (64-bit, non-prefetchable) [size=16K]
Region 3: Memory at fe9d0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at fe800000 [disabled] [size=1M]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [98] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [68] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=6
Status: Bus=255 Dev=31 Func=0 64bit+ 133MHz+ SCD- USC-, DC=simple,
DMMRBC=2, DMOST=6, DMCRS=3, RSCEM-
Capabilities: [b0] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=1 offset=00002000
PBA: BAR=1 offset=00003000
03:06.1 Fibre Channel: LSI Logic / Symbios Logic FC949X Fibre Channel
Adapter (rev 01)
Subsystem: LSI Logic / Symbios Logic: Unknown device 1100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 72 (16000ns min, 2500ns max), Cache Line Size 10
Interrupt: pin B routed to IRQ 16
Region 0: I/O ports at c000 [disabled] [size=256]
Region 1: Memory at fe9e8000 (64-bit, non-prefetchable) [size=16K]
Region 3: Memory at fe9c0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at fe700000 [disabled] [size=1M]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [98] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [68] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=6
Status: Bus=255 Dev=31 Func=1 64bit+ 133MHz+ SCD- USC-, DC=simple,
DMMRBC=2, DMOST=6, DMCRS=3, RSCEM-
Capabilities: [b0] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=1 offset=00002000
PBA: BAR=1 offset=00003000
04:07.0 Ethernet controller: Intel Corporation 82597EX 10GbE Ethernet
Controller (rev 02)
Subsystem: Intel Corporation: Unknown device a00c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 16
Region 0: Memory at feaf8000 (64-bit, non-prefetchable) [size=32K]
Region 2: Memory at fea80000 (64-bit, non-prefetchable) [size=256K]
Region 4: I/O ports at ec00 [size=32]
Expansion ROM at fea40000 [disabled] [size=256K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=2
Status: Bus=4 Dev=7 Func=0 64bit+ 133MHz+ SCD- USC-, DC=simple,
DMMRBC=3, DMOST=2, DMCRS=4, RSCEM-
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
08:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI
Express-to-PCI Bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=08, secondary=09, subordinate=09, sec-latency=64
Memory behind bridge: feb00000-febfffff
Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/4 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [80] #0d [0000]
Capabilities: [90] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 512 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
09:02.0 FireWire (IEEE 1394): Texas Instruments TSB82AA2 IEEE-1394b Link
Layer Controller (rev 01) (prog-if 10 [OHCI])
Subsystem: Timedia Technology Co Ltd: Unknown device 3110
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 1000ns max), Cache Line Size 10
Interrupt: pin A routed to IRQ 17
Region 0: Memory at febff800 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at febf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
CPU0 CPU1 CPU2 CPU3
0: 128 4 137 687908 IO-APIC-edge timer
1: 0 0 0 10 IO-APIC-edge i8042
6: 0 0 0 3 IO-APIC-edge floppy
8: 0 0 0 1 IO-APIC-edge rtc
9: 0 0 0 0 IO-APIC-fasteoi acpi
12: 0 0 0 105 IO-APIC-edge i8042
16: 0 0 0 460 IO-APIC-fasteoi ioc1
17: 0 0 3 645 IO-APIC-fasteoi ioc0
18: 0 3 5 10079 IO-APIC-fasteoi
megaraid
21: 0 0 0 106 IO-APIC-fasteoi
ehci_hcd:usb1
22: 0 0 0 0 IO-APIC-fasteoi
ohci_hcd:usb2
509: 0 0 111 274008 PCI-MSI-edge eth0
510: 0 0 3 478 PCI-MSI-edge eth0
511: 0 0 5 6223 PCI-MSI-edge eth0
NMI: 109 37 38 49
LOC: 688031 688008 687984 687960
ERR: 0
00000000-0009f7ff : System RAM
0009f800-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000cafff : Video ROM
000cb000-000cc7ff : Adapter ROM
000cc800-000ccfff : Adapter ROM
000cd000-000cf5ff : Adapter ROM
000f0000-000fffff : System ROM
00100000-dffeffff : System RAM
00200000-00436078 : Kernel code
00436079-0052d76f : Kernel data
04000000-07ffffff : GART
dfff0000-dfffdfff : ACPI Tables
dfffe000-dfffffff : ACPI Non-volatile Storage
f0000000-f7ffffff : PCI Bus #01
f0000000-f7ffffff : 0000:01:05.0
fdf00000-fdffffff : PCI Bus #02
fdf00000-fdffffff : PCI Bus #03
fdff0000-fdffffff : 0000:03:04.0
fdff0000-fdffffff : MegaRAID: LSI Logic Corporation
fe5f7c00-fe5f7c0f : 0000:00:09.0
fe5f7c00-fe5f7c0f : forcedeth
fe5f8000-fe5f8fff : 0000:00:09.0
fe5f8000-fe5f8fff : forcedeth
fe5f9000-fe5f9fff : 0000:00:08.0
fe5f9000-fe5f9fff : forcedeth
fe5fa000-fe5fa0ff : 0000:00:09.0
fe5fa000-fe5fa0ff : forcedeth
fe5fa400-fe5fa40f : 0000:00:08.0
fe5fa400-fe5fa40f : forcedeth
fe5fa800-fe5fa8ff : 0000:00:08.0
fe5fa800-fe5fa8ff : forcedeth
fe5fac00-fe5facff : 0000:00:02.1
fe5fac00-fe5facff : ehci_hcd
fe5fb000-fe5fbfff : 0000:00:02.0
fe5fb000-fe5fbfff : ohci_hcd
fe600000-fe6fffff : PCI Bus #01
fe600000-fe61ffff : 0000:01:05.0
fe6f0000-fe6fffff : 0000:01:05.0
fe700000-feafffff : PCI Bus #02
fe700000-fe9fffff : PCI Bus #03
fe700000-fe7fffff : 0000:03:06.1
fe800000-fe8fffff : 0000:03:06.0
fe9c0000-fe9cffff : 0000:03:06.1
fe9d0000-fe9dffff : 0000:03:06.0
fe9e8000-fe9ebfff : 0000:03:06.1
fe9ec000-fe9effff : 0000:03:06.0
fe9f0000-fe9fffff : 0000:03:04.0
fea00000-feafffff : PCI Bus #04
fea40000-fea7ffff : 0000:04:07.0
fea80000-feabffff : 0000:04:07.0
feaf8000-feafffff : 0000:04:07.0
feb00000-febfffff : PCI Bus #08
feb00000-febfffff : PCI Bus #09
febf8000-febfbfff : 0000:09:02.0
febff800-febfffff : 0000:09:02.0
fec00000-fec00fff : reserved
fed00000-fed003ff : HPET 0
fee00000-feefffff : reserved
ff700000-ffffffff : reserved
100000000-11fffffff : System RAM
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/