Re: AHCI - remove probing of ata2

[Robert Hancock]

Paul Rolland wrote:
> Hello,
>
> I'm using an Asus P5W DH motherboard, with an Intel ICH7 controler, and a 
> Jmicron JMB363.
>
> On the Intel, I've connected an IDE HDD and a CD-RW, no problem.
> On the SATA side, i've connected 3 SATA disks, but at boot time, the kernel
> detects 4 ports, and goes on timeout on ata2 :
>
> ..
> ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
> ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part 
> ata1: SATA max UDMA/133 cmd 0xFFFFC200000BC900 ctl 0x0 bmdma 0x0 irq 505
> ata2: SATA max UDMA/133 cmd 0xFFFFC200000BC980 ctl 0x0 bmdma 0x0 irq 505
> ata3: SATA max UDMA/133 cmd 0xFFFFC200000BCA00 ctl 0x0 bmdma 0x0 irq 505
> ata4: SATA max UDMA/133 cmd 0xFFFFC200000BCA80 ctl 0x0 bmdma 0x0 irq 505
> scsi0 : ahci
> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata1.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 NCQ (depth 31/32)
> ata1.00: ata1: dev 0 multi count 0
> ata1.00: configured for UDMA/133
> scsi1 : ahci
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata2.00: qc timeout (cmd 0xec)
> ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
> ata2: port is slow to respond, please be patient (Status 0x80)
> ata2: port failed to respond (30 secs, Status 0x80)
> ata2: COMRESET failed (device not ready)
> ata2: hardreset failed, retrying in 5 secs
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata2.00: ATA-6, max UDMA/133, 640 sectors: LBA 
> ata2.00: ata2: dev 0 multi count 1
> ata2.00: configured for UDMA/133
> scsi2 : ahci
> ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata3.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 NCQ (depth 31/32)
> ata3.00: ata3: dev 0 multi count 0
> ata3.00: configured for UDMA/133
> ..
>
> Is there a way to exclude ata2 from probing ? Nothing is connected, and there
> is no associated port on the motherboard...

There is something connected, I believe what's actually there on this 
board on that port is the SiI4723 chip which is connected to two other 
SATA ports. For whatever reason it gets detected as a drive, and it also 
seems to be not responding until we do a few resets..

http://www.siliconimage.com/products/product.aspx?id=64

> The second problem is the Jmicron controler. It can act as IDE, SATA, ...
> but I've configured it as IDE in the BIOS, and connected a DRD-RW on.
> Problem is that IDE driver detects it, as containing ide2 and ide3, and
> when probing for the DVD, I've got a lot of timeout on the command.
> .. But, I'm lost in all the JMICRON configuration possibilities in the 
> kernel :
>  - it is detected by the IDE driver,
>  - it can be activated in ATA/ATAPI/MFM/RLL
>  - it can be activated in Serial ATA (prod) and Parallel ATA (experimental)
>
> What should I select ?

My advice on recent kernels is just set CONFIG_IDE=n and enable 
PATA_JMICRON if you want JMicron support, unless you really want to use 
the crusty old IDE layer..

--
Robert Hancock      Saskatoon, SK, Canada
To email, remove "nospam" from hancockr@xxxxxxxxxxxxx
Home Page: http://www.roberthancock.com/

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/