Re: hda: set_drive_speed_status: status=0x51 { DriveReady SeekCompleteError }

[Sergei Shtylyov]

John Sigler wrote:

> > > What do the warnings mean? :-)

> > That your drive does not support set transfer mode/speed command at 

   Which is perfectly valid in the original ATA spec.

> > all, or that value which kernel tried is not supported by the drive...

   They just should skip programming the drive in this case, and set its 
default speed to the chipset.

> > I would guess that some contractor wrote firmware for device for PQI 
> > in one day for $100, and before that somebody else designed ATA-SD 
> > bridge for PQI for another $100.

   Hehe.

> > I guess that these two printk()s happen because drive claims to 
> > support pio0,1,2 - so Linux tries pio2, drive refuses, Linux tries 

  Which it shuldn't do since the drive only indicates its default mode (modes 
0-2 aren't included in the PIO support mask -- there's only 3 and 4 there).

> > pio1, drive refuses, and finally as pio0 is default, that one gets 
> > used.  Which is more or less confirmed by having no '*' sign in front 
> > of any pio - with "real" drives you should see '*' in front of one of 
> > listed dma/pio modes.

> > You should ask reseller how they can ship drive which does not conform 
> > to any ATA standard...

   Doesn't it conform to ATA? :-)

> I took drivers/ide/pci/via82cxxx.c and sprinkled ENTER/EXIT printk's.
> http://lxr.linux.no/source/drivers/ide/pci/via82cxxx.c

> via82cxxx_tune_drive() and via82cxxx_ide_dma_check() both call 
> via_set_drive() which calls ide_config_drive_speed().

> http://lxr.linux.no/source/drivers/ide/ide-iops.c#L769
>
>   if (error)
>   {
>     (void) ide_dump_status(drive, "set_drive_speed_status", stat);
>     printk(KERN_INFO "EXIT %s error\n", __func__);
>     return error;
>   }

> Does someone know why error is not set to 0?

   Why it *does* set to one, you wanted to ask? Because it *does* get set 
after a loop above exits.

> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> VP_IDE: IDE controller at PCI slot 0000:00:07.1
> VP_IDE: chipset revision 6
> VP_IDE: not 100% native mode: will probe irqs later
> VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
>     ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:pio, hdb:pio
>     ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:pio, hdd:pio
> Probing IDE interface ide0...
> hda: PQI IDE DiskOnModule, ATA DISK drive
> ENTER via82cxxx_tune_drive
> ENTER via_set_drive
> ENTER ide_config_drive_speed
> hda: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
> hda: set_drive_speed_status: error=0x04 { DriveStatusError }
> EXIT ide_config_drive_speed error
> ENTER via_set_speed
> EXIT via_set_speed
> EXIT via_set_drive
> EXIT via82cxxx_tune_drive pio == 255

   255 is PIO auto-tuning request.

> ENTER via82cxxx_ide_dma_check
> ENTER via_set_drive
> ENTER ide_config_drive_speed
> hda: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
> hda: set_drive_speed_status: error=0x04 { DriveStatusError }

MBR, Sergei
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/