Re: question about sata-error on boot.
From: Tejun Heo
Date: Mon Nov 12 2007 - 08:29:23 EST
(cc Robert Hancock, maybe we need ATA_LFLAG_HRST_TO_RESUME for these
controllers?)
Andrew Morton wrote:
>> On Fri, 2 Nov 2007 19:34:20 +0100 "Hemmann, Volker Armin" <volker.armin.hemmann@xxxxxxxxxxxxxxx> wrote:
>> Hi,
>
> (cc linux-ide)
>
>> for some time (and I can't say for how long, but the board is less than a
>> month old) I get this error on boot:
>>
>> [ 42.116273] ahci 0000:00:0a.0: version 2.2
>> [ 42.116482] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
>> [ 42.116653] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23
>> (level, low) -> IRQ 23
>> [ 43.119478] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf
>> impl IDE mode
>> [ 43.119778] ahci 0000:00:0a.0: flags: 64bit led clo pmp pio
>> [ 43.119943] PCI: Setting latency timer of device 0000:00:0a.0 to 64
>> [ 43.120149] scsi0 : ahci
>> [ 43.120365] scsi1 : ahci
>> [ 43.120556] scsi2 : ahci
>> [ 43.120741] scsi3 : ahci
>> [ 43.120927] ata1: SATA max UDMA/133 cmd 0xffffc20000014100 ctl
>> 0x0000000000000000 bmdma 0x0000000000000000 irq 315
>> [ 43.121227] ata2: SATA max UDMA/133 cmd 0xffffc20000014180 ctl
>> 0x0000000000000000 bmdma 0x0000000000000000 irq 315
>> [ 43.121526] ata3: SATA max UDMA/133 cmd 0xffffc20000014200 ctl
>> 0x0000000000000000 bmdma 0x0000000000000000 irq 315
>> [ 43.121826] ata4: SATA max UDMA/133 cmd 0xffffc20000014280 ctl
>> 0x0000000000000000 bmdma 0x0000000000000000 irq 315
>> [ 43.934296] ata1: softreset failed (1st FIS failed)
>> [ 43.934461] ata1: reset failed (errno=-5), retrying in 10 secs
>> [ 53.885194] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> [ 53.885890] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133
>> [ 53.886056] ata1.00: 312581808 sectors, multi 16: LBA48
>> [ 53.886804] ata1.00: configured for UDMA/133
>> [ 54.201147] ata2: SATA link down (SStatus 0 SControl 300)
>> [ 54.517101] ata3: SATA link down (SStatus 0 SControl 300)
>> [ 54.833055] ata4: SATA link down (SStatus 0 SControl 300)
>>
>> The board has four ports and I use the first one. After that, the computer
>> boots and works fine. Harddisk-speed is normal. Kernel is 2.6.22.9 with
>> cfs&reiser4 patches.
>>
>> Is this something to worry about?
>>
>> Following is lspci -v and dmesg, config is attached.
>> lspci -v
>> 00:00.0 RAM memory: nVidia Corporation MCP65 Memory Controller (rev a1)
>> Subsystem: ASRock Incorporation Unknown device 0444
>> Flags: bus master, 66MHz, fast devsel, latency 0
>> Capabilities: [44] HyperTransport: Slave or Primary Interface
>> Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed-
>>
>> 00:01.0 ISA bridge: nVidia Corporation MCP65 LPC Bridge (rev a2)
>> Subsystem: ASRock Incorporation Unknown device 0441
>> Flags: bus master, 66MHz, fast devsel, latency 0
>> I/O ports at 2f00 [size=256]
>>
>> 00:01.1 SMBus: nVidia Corporation MCP65 SMBus (rev a1)
>> Subsystem: ASRock Incorporation Unknown device 0446
>> Flags: 66MHz, fast devsel, IRQ 11
>> I/O ports at ac00 [size=64]
>> I/O ports at 2d00 [size=64]
>> I/O ports at 2e00 [size=64]
>> Capabilities: [44] Power Management version 2
>>
>> 00:01.2 RAM memory: nVidia Corporation MCP65 Memory Controller (rev a1)
>> Subsystem: ASRock Incorporation Unknown device 0446
>> Flags: 66MHz, fast devsel
>>
>> 00:02.0 USB Controller: nVidia Corporation MCP65 USB Controller (rev a1)
>> (prog-if 10 [OHCI])
>> Subsystem: ASRock Incorporation Unknown device 0454
>> Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21
>> Memory at f9dff000 (32-bit, non-prefetchable) [size=4K]
>> Capabilities: [44] Power Management version 2
>>
>> 00:02.1 USB Controller: nVidia Corporation MCP65 USB Controller (rev a1)
>> (prog-if 20 [EHCI])
>> Subsystem: ASRock Incorporation Unknown device 0455
>> Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22
>> Memory at f9dfec00 (32-bit, non-prefetchable) [size=256]
>> Capabilities: [44] Debug port
>> Capabilities: [80] Power Management version 2
>>
>> 00:08.0 PCI bridge: nVidia Corporation MCP65 PCI bridge (rev a1) (prog-if 01
>> [Subtractive decode])
>> Flags: bus master, 66MHz, fast devsel, latency 0
>> Bus: primary=00, secondary=02, subordinate=02, sec-latency=128
>> I/O behind bridge: 0000c000-0000dfff
>> Memory behind bridge: f9f00000-f9ffffff
>> Prefetchable memory behind bridge: 88000000-880fffff
>> Capabilities: [b8] Subsystem: ASRock Incorporation Unknown device 0449
>> Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed-
>>
>> 00:09.0 IDE interface: nVidia Corporation MCP65 IDE (rev a1) (prog-if 8a
>> [Master SecP PriP])
>> Subsystem: ASRock Incorporation Unknown device 0448
>> Flags: bus master, 66MHz, fast devsel, latency 0
>> [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled]
>> [size=8]
>> [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled]
>> [size=1]
>> [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled]
>> [size=8]
>> [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled]
>> [size=1]
>> I/O ports at ffa0 [size=16]
>> Capabilities: [44] Power Management version 2
>>
>> 00:0a.0 IDE interface: nVidia Corporation MCP65 SATA Controller (rev a1)
>> (prog-if 85 [Master SecO PriO])
>> Subsystem: ASRock Incorporation Unknown device 045d
>> Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 315
>> I/O ports at 0e00 [size=8]
>> I/O ports at 0e20 [size=4]
>> I/O ports at 0e40 [size=8]
>> I/O ports at 0e60 [size=4]
>> I/O ports at 9800 [size=16]
>> Memory at f9dfc000 (32-bit, non-prefetchable) [size=8K]
>> Capabilities: [44] Power Management version 2
>> Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+
>> Queue=0/3 Enable+
>> Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+
>>
>> 00:0b.0 PCI bridge: nVidia Corporation Unknown device 045b (rev a1) (prog-if
>> 00 [Normal decode])
>> Flags: bus master, fast devsel, latency 0
>> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
>> I/O behind bridge: 0000b000-0000bfff
>> Memory behind bridge: f9e00000-f9efffff
>> Capabilities: [40] Subsystem: ASRock Incorporation Unknown device 045b
>> Capabilities: [48] Power Management version 2
>> Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+
>> Queue=0/1 Enable+
>> Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed-
>> Capabilities: [80] Express Root Port (Slot+), MSI 00
>>
>> 00:0c.0 PCI bridge: nVidia Corporation MCP65 PCI Express bridge (rev a1)
>> (prog-if 00 [Normal decode])
>> Flags: bus master, fast devsel, latency 0
>> Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
>> Capabilities: [40] Subsystem: ASRock Incorporation Unknown device 045a
>> Capabilities: [48] Power Management version 2
>> Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+
>> Queue=0/1 Enable+
>> Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed-
>> Capabilities: [80] Express Root Port (Slot+), MSI 00
>>
>> 00:0d.0 PCI bridge: nVidia Corporation MCP65 PCI Express bridge (rev a1)
>> (prog-if 00 [Normal decode])
>> Flags: bus master, fast devsel, latency 0
>> Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
>> I/O behind bridge: 0000e000-0000efff
>> Memory behind bridge: fa000000-febfffff
>> Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
>> Capabilities: [40] Subsystem: ASRock Incorporation Unknown device 0458
>> Capabilities: [48] Power Management version 2
>> Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+
>> Queue=0/1 Enable+
>> Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed-
>> Capabilities: [80] Express Root Port (Slot+), MSI 00
>>
>> 00:0e.0 PCI bridge: nVidia Corporation MCP65 PCI Express bridge (rev a1)
>> (prog-if 00 [Normal decode])
>> Flags: bus master, fast devsel, latency 0
>> Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
>> Capabilities: [40] Subsystem: ASRock Incorporation Unknown device 0459
>> Capabilities: [48] Power Management version 2
>> Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+
>> Queue=0/1 Enable+
>> Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed-
>> Capabilities: [80] Express Root Port (Slot+), MSI 00
>>
>> 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
>> HyperTransport Technology Configuration
>> Flags: fast devsel
>> Capabilities: [80] HyperTransport: Host or Secondary Interface
>>
>> 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
>> Address Map
>> Flags: fast devsel
>>
>> 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM
>> Controller
>> Flags: fast devsel
>>
>> 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
>> Miscellaneous Control
>> Flags: fast devsel
>> Capabilities: [f0] #0f [0010]
>>
>> 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI
>> Express Gigabit Ethernet controller (rev 01)
>> Subsystem: ASRock Incorporation Unknown device 8168
>> Flags: bus master, fast devsel, latency 0, IRQ 19
>> I/O ports at b800 [size=256]
>> Memory at f9eff000 (64-bit, non-prefetchable) [size=4K]
>> Expansion ROM at f9ec0000 [disabled] [size=128K]
>> Capabilities: [40] Power Management version 2
>> Capabilities: [48] Vital Product Data
>> Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+
>> Queue=0/1 Enable-
>> Capabilities: [60] Express Endpoint, MSI 00
>> Capabilities: [84] Vendor Specific Information
>>
>> 02:07.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000
>> Controller (PHY/Link) (prog-if 10 [OHCI])
>> Subsystem: ASRock Incorporation Unknown device 8023
>> Flags: bus master, medium devsel, latency 128, IRQ 11
>> Memory at f9fff800 (32-bit, non-prefetchable) [size=2K]
>> Memory at f9ff8000 (32-bit, non-prefetchable) [size=16K]
>> Capabilities: [44] Power Management version 2
>>
>> 02:08.0 SCSI storage controller: Adaptec AHA-2944UW / AIC-7884U (rev 01)
>> Subsystem: Adaptec Unknown device 7884
>> Flags: bus master, medium devsel, latency 128, IRQ 5
>> I/O ports at d800 [size=256]
>> Memory at f9ffe000 (32-bit, non-prefetchable) [size=4K]
>> Expansion ROM at 88020000 [disabled] [size=64K]
>> Capabilities: [dc] Power Management version 1
>>
>> 02:09.0 Multimedia audio controller: Creative Labs SB0400 Audigy2 Value
>> Subsystem: Creative Labs Unknown device 1001
>> Flags: bus master, medium devsel, latency 128, IRQ 17
>> I/O ports at dc00 [size=64]
>> Capabilities: [dc] Power Management version 2
>>
>> 02:0a.0 Mass storage controller: HighPoint Technologies, Inc.
>> HPT366/368/370/370A/372/372N (rev 01)
>> Flags: bus master, medium devsel, latency 120, IRQ 18
>> I/O ports at d480 [size=8]
>> I/O ports at d400 [size=4]
>> I/O ports at d000 [size=256]
>> Expansion ROM at 88000000 [disabled by cmd] [size=128K]
>>
>> 02:0a.1 Mass storage controller: HighPoint Technologies, Inc.
>> HPT366/368/370/370A/372/372N (rev 01)
>> Flags: bus master, medium devsel, latency 120, IRQ 18
>> I/O ports at cc00 [size=8]
>> I/O ports at c880 [size=4]
>> I/O ports at c400 [size=256]
>>
>> 04:00.0 VGA compatible controller: nVidia Corporation GeForce 8600 GT (rev a1)
>> (prog-if 00 [VGA])
>> Subsystem: nVidia Corporation Unknown device 0439
>> Flags: bus master, fast devsel, latency 0, IRQ 16
>> Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
>> Memory at d0000000 (64-bit, prefetchable) [size=256M]
>> Memory at fa000000 (64-bit, non-prefetchable) [size=32M]
>> I/O ports at ec00 [size=128]
>> [virtual] Expansion ROM at febe0000 [disabled] [size=128K]
>> Capabilities: [60] Power Management version 2
>> Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+
>> Queue=0/0 Enable-
>> Capabilities: [78] Express Endpoint, MSI 0
>>
>> dmesg:
>> [ 0.000000] Linux version 2.6.22.9-cfs-v22reiser4 (root@energy) (gcc
>> version 4.2.2 (Gentoo 4.2.2 p1.0)) #5 SMP Thu Oct 25 14:39:54 CEST 2007
>> [ 0.000000] Command line: root=/dev/sda3 nmi_watchdog=0
>> [ 0.000000] BIOS-provided physical RAM map:
>> [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
>> [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
>> [ 0.000000] BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
>> [ 0.000000] BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable)
>> [ 0.000000] BIOS-e820: 000000007ffb0000 - 000000007ffc0000 (ACPI data)
>> [ 0.000000] BIOS-e820: 000000007ffc0000 - 000000007fff0000 (ACPI NVS)
>> [ 0.000000] BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
>> [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
>> [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
>> [ 0.000000] BIOS-e820: 00000000ff380000 - 0000000100000000 (reserved)
>> [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used
>> [ 0.000000] Entering add_active_range(0, 256, 524208) 1 entries of 256 used
>> [ 0.000000] end_pfn_map = 1048576
>> [ 0.000000] DMI present.
>> [ 0.000000] ACPI: RSDP 000FA530, 0014 (r0 ACPIAM)
>> [ 0.000000] ACPI: RSDT 7FFB0000, 003C (r1 A M I OEMRSDT 9000720 MSFT
>> 97)
>> [ 0.000000] ACPI: FACP 7FFB0200, 0084 (r2 A_M_I OEMFACP 12000601 MSFT
>> 97)
>> [ 0.000000] ACPI: DSDT 7FFB0450, 4FFA (r1 ASR19 ASR1915A 15A INTL
>> 20051117)
>> [ 0.000000] ACPI: FACS 7FFC0000, 0040
>> [ 0.000000] ACPI: APIC 7FFB0390, 0080 (r1 A M I OEMAPIC 9000720 MSFT
>> 97)
>> [ 0.000000] ACPI: MCFG 7FFB0410, 003C (r1 A M I OEMMCFG 9000720 MSFT
>> 97)
>> [ 0.000000] ACPI: OEMB 7FFC0040, 0060 (r1 A M I AMI_OEM 9000720 MSFT
>> 97)
>> [ 0.000000] ACPI: HPET 7FFB5450, 0038 (r1 A M I OEMHPET0 9000720 MSFT
>> 97)
>> [ 0.000000] ACPI: SSDT 7FFB5490, 030E (r1 A M I POWERNOW 1 AMD
>> 1)
>> [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used
>> [ 0.000000] Entering add_active_range(0, 256, 524208) 1 entries of 256 used
>> [ 0.000000] No mptable found.
>> [ 0.000000] Zone PFN ranges:
>> [ 0.000000] DMA 0 -> 4096
>> [ 0.000000] DMA32 4096 -> 1048576
>> [ 0.000000] Normal 1048576 -> 1048576
>> [ 0.000000] early_node_map[2] active PFN ranges
>> [ 0.000000] 0: 0 -> 159
>> [ 0.000000] 0: 256 -> 524208
>> [ 0.000000] On node 0 totalpages: 524111
>> [ 0.000000] DMA zone: 56 pages used for memmap
>> [ 0.000000] DMA zone: 905 pages reserved
>> [ 0.000000] DMA zone: 3038 pages, LIFO batch:0
>> [ 0.000000] DMA32 zone: 7110 pages used for memmap
>> [ 0.000000] DMA32 zone: 513002 pages, LIFO batch:31
>> [ 0.000000] Normal zone: 0 pages used for memmap
>> [ 0.000000] ACPI: PM-Timer IO Port: 0x2008
>> [ 0.000000] ACPI: Local APIC address 0xfee00000
>> [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
>> [ 0.000000] Processor #0 (Bootup-CPU)
>> [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
>> [ 0.000000] Processor #1
>> [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
>> [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
>> [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
>> [ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
>> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
>> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
>> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
>> [ 0.000000] ACPI: IRQ0 used by override.
>> [ 0.000000] ACPI: IRQ2 used by override.
>> [ 0.000000] ACPI: IRQ9 used by override.
>> [ 0.000000] ACPI: IRQ14 used by override.
>> [ 0.000000] ACPI: IRQ15 used by override.
>> [ 0.000000] Setting APIC routing to flat
>> [ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
>> [ 0.000000] Using ACPI (MADT) for SMP configuration information
>> [ 0.000000] Allocating PCI resources starting at 88000000 (gap:
>> 80000000:7ec00000)
>> [ 0.000000] PERCPU: Allocating 29336 bytes of per cpu data
>> [ 0.000000] Built 1 zonelists. Total pages: 516040
>> [ 0.000000] Kernel command line: root=/dev/sda3 nmi_watchdog=0
>> [ 0.000000] Initializing CPU#0
>> [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
>> [ 0.000000] Marking TSC unstable due to TSCs unsynchronized
>> [ 40.731282] time.c: Detected 3013.892 MHz processor.
>> [ 40.735511] Console: colour VGA+ 80x25
>> [ 40.745472] Dentry cache hash table entries: 262144 (order: 9, 2097152
>> bytes)
>> [ 40.746781] Inode-cache hash table entries: 131072 (order: 8, 1048576
>> bytes)
>> [ 40.747137] Checking aperture...
>> [ 40.747300] CPU 0: aperture @ ecc8000000 size 32 MB
>> [ 40.747464] Aperture too small (32 MB)
>> [ 40.753296] No AGP bridge found
>> [ 40.765569] Memory: 2060372k/2096832k available (2200k kernel code, 35792k
>> reserved, 669k data, 184k init)
>> [ 40.847841] Calibrating delay using timer specific routine.. 6034.57
>> BogoMIPS (lpj=10053716)
>> [ 40.848202] Mount-cache hash table entries: 256
>> [ 40.848437] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
>> bytes/line)
>> [ 40.848602] CPU: L2 Cache: 1024K (64 bytes/line)
>> [ 40.848766] CPU: Physical Processor ID: 0
>> [ 40.848928] CPU: Processor Core ID: 0
>> [ 40.849103] Freeing SMP alternatives: 26k freed
>> [ 40.849613] ACPI: Core revision 20070126
>> [ 40.884963] Using local APIC timer interrupts.
>> [ 40.918232] result 12557891
>> [ 40.918393] Detected 12.557 MHz APIC timer.
>> [ 40.921062] Booting processor 1/2 APIC 0x1
>> [ 40.931358] Initializing CPU#1
>> [ 41.014213] Calibrating delay using timer specific routine.. 6030.95
>> BogoMIPS (lpj=10046323)
>> [ 41.014218] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
>> bytes/line)
>> [ 41.014219] CPU: L2 Cache: 1024K (64 bytes/line)
>> [ 41.014221] CPU: Physical Processor ID: 0
>> [ 41.014222] CPU: Processor Core ID: 1
>> [ 41.014303] AMD Athlon(tm) 64 X2 Dual Core Processor 6000+ stepping 03
>> [ 41.017460] Brought up 2 CPUs
>> [ 41.019044] NET: Registered protocol family 16
>> [ 41.019258] ACPI: bus type pci registered
>> [ 41.019428] PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
>> [ 41.019592] PCI: Not using MMCONFIG.
>> [ 41.019755] PCI: Using configuration type 1
>> [ 41.024096] ACPI: Interpreter enabled
>> [ 41.024259] ACPI: Using IOAPIC for interrupt routing
>> [ 41.024586] Error attaching device data
>> [ 41.024751] Error attaching device data
>> [ 41.024916] Error attaching device data
>> [ 41.025082] Error attaching device data
>> [ 41.031242] ACPI: PCI Root Bridge [PCI0] (0000:00)
>> [ 41.031413] PCI: Probing PCI hardware (bus 00)
>> [ 41.031942] PCI: Transparent bridge - 0000:00:08.0
>> [ 41.032367] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>> [ 41.032524] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
>> [ 41.032638] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR10._PRT]
>> [ 41.032705] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT]
>> [ 41.032771] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR13._PRT]
>> [ 41.032836] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT]
>> [ 41.037361] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *5
>> [ 41.037882] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *10
>> [ 41.038385] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *10
>> [ 41.038888] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *11
>> [ 41.039391] ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *0,
>> disabled.
>> [ 41.039923] ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *10
>> [ 41.040426] ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0,
>> disabled.
>> [ 41.040972] ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *10
>> [ 41.041475] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *5
>> [ 41.041978] ACPI: PCI Interrupt Link [LMAD] (IRQs 20 21 22 23) *0,
>> disabled.
>> [ 41.042510] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *7
>> [ 41.043012] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0,
>> disabled.
>> [ 41.043544] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *0,
>> disabled.
>> [ 41.044088] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11
>> [ 41.044593] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *0,
>> disabled.
>> [ 41.045126] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *15
>> [ 41.045630] ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *0,
>> disabled.
>> [ 41.046189] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0,
>> disabled.
>> [ 41.046722] ACPI: PCI Interrupt Link [UB11] (IRQs 20 21 22 23) *0,
>> disabled.
>> [ 41.047255] ACPI: PCI Interrupt Link [UB12] (IRQs 20 21 22 23) *0,
>> disabled.
>> [ 41.047708] Linux Plug and Play Support v0.97 (c) Adam Belay
>> [ 41.047879] pnp: PnP ACPI init
>> [ 41.048045] ACPI: bus type pnp registered
>> [ 41.051043] pnp: PnP ACPI: found 13 devices
>> [ 41.051205] ACPI: ACPI bus type pnp unregistered
>> [ 41.051432] SCSI subsystem initialized
>> [ 41.051618] libata version 2.21 loaded.
>> [ 41.051654] usbcore: registered new interface driver usbfs
>> [ 41.051834] usbcore: registered new interface driver hub
>> [ 41.052016] usbcore: registered new device driver usb
>> [ 41.052197] PCI: Using ACPI for IRQ routing
>> [ 41.052360] PCI: If a device doesn't work, try "pci=routeirq". If it
>> helps, post a report
>> [ 41.052747] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
>> [ 41.053027] hpet0: 3 32-bit timers, 25000000 Hz
>> [ 41.054255] pnp: 00:05: iomem range 0x0-0x0 could not be reserved
>> [ 41.054421] pnp: 00:05: iomem range 0xfee01000-0xfeefffff has been reserved
>> [ 41.054589] pnp: 00:07: iomem range 0xfec00000-0xfec00fff could not be
>> reserved
>> [ 41.054886] pnp: 00:07: iomem range 0xfee00000-0xfee00fff could not be
>> reserved
>> [ 41.055185] pnp: 00:0a: ioport range 0x290-0x29f has been reserved
>> [ 41.055351] pnp: 00:0b: iomem range 0xe0000000-0xefffffff has been reserved
>> [ 41.055519] pnp: 00:0c: iomem range 0x0-0x9ffff could not be reserved
>> [ 41.055685] pnp: 00:0c: iomem range 0xc0000-0xcffff has been reserved
>> [ 41.055850] pnp: 00:0c: iomem range 0xe0000-0xfffff could not be reserved
>> [ 41.056017] pnp: 00:0c: iomem range 0x100000-0x7fffffff could not be
>> reserved
>> [ 41.056338] PCI: Bridge: 0000:00:08.0
>> [ 41.056501] IO window: c000-dfff
>> [ 41.056664] MEM window: f9f00000-f9ffffff
>> [ 41.056829] PREFETCH window: 88000000-880fffff
>> [ 41.056993] PCI: Bridge: 0000:00:0b.0
>> [ 41.057156] IO window: b000-bfff
>> [ 41.057319] MEM window: f9e00000-f9efffff
>> [ 41.057451] Time: hpet clocksource has been installed.
>> [ 41.057645] PREFETCH window: disabled.
>> [ 41.057808] PCI: Bridge: 0000:00:0c.0
>> [ 41.057970] IO window: disabled.
>> [ 41.058132] MEM window: disabled.
>> [ 41.058294] PREFETCH window: disabled.
>> [ 41.058457] PCI: Bridge: 0000:00:0d.0
>> [ 41.058619] IO window: e000-efff
>> [ 41.058783] MEM window: fa000000-febfffff
>> [ 41.058946] PREFETCH window: d0000000-dfffffff
>> [ 41.059110] PCI: Bridge: 0000:00:0e.0
>> [ 41.059272] IO window: disabled.
>> [ 41.059434] MEM window: disabled.
>> [ 41.059596] PREFETCH window: disabled.
>> [ 41.059765] PCI: Setting latency timer of device 0000:00:08.0 to 64
>> [ 41.059770] PCI: Setting latency timer of device 0000:00:0b.0 to 64
>> [ 41.059774] PCI: Setting latency timer of device 0000:00:0c.0 to 64
>> [ 41.059778] PCI: Setting latency timer of device 0000:00:0d.0 to 64
>> [ 41.059783] PCI: Setting latency timer of device 0000:00:0e.0 to 64
>> [ 41.059801] NET: Registered protocol family 2
>> [ 41.100619] IP route cache hash table entries: 65536 (order: 7, 524288
>> bytes)
>> [ 41.101145] TCP established hash table entries: 131072 (order: 9, 3145728
>> bytes)
>> [ 41.102591] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
>> [ 41.103136] TCP: Hash tables configured (established 131072 bind 65536)
>> [ 41.103302] TCP reno registered
>> [ 41.114592] Total HugeTLB memory allocated, 0
>> [ 41.114825] Loading Reiser4. See www.namesys.com for a description of
>> Reiser4.
>> [ 41.115182] io scheduler noop registered
>> [ 41.115352] io scheduler cfq registered (default)
>> [ 41.116320] Boot video device is 0000:04:00.0
>> [ 41.116435] PCI: Setting latency timer of device 0000:00:0b.0 to 64
>> [ 41.116450] assign_interrupt_mode Found MSI capability
>> [ 41.116629] Allocate Port Service[0000:00:0b.0:pcie00]
>> [ 41.116670] PCI: Setting latency timer of device 0000:00:0c.0 to 64
>> [ 41.116685] assign_interrupt_mode Found MSI capability
>> [ 41.116857] Allocate Port Service[0000:00:0c.0:pcie00]
>> [ 41.116893] PCI: Setting latency timer of device 0000:00:0d.0 to 64
>> [ 41.116908] assign_interrupt_mode Found MSI capability
>> [ 41.117080] Allocate Port Service[0000:00:0d.0:pcie00]
>> [ 41.117117] PCI: Setting latency timer of device 0000:00:0e.0 to 64
>> [ 41.117135] assign_interrupt_mode Found MSI capability
>> [ 41.120561] Allocate Port Service[0000:00:0e.0:pcie00]
>> [ 41.120731] input: Power Button (FF) as /class/input/input0
>> [ 41.120895] ACPI: Power Button (FF) [PWRF]
>> [ 41.121116] input: Power Button (CM) as /class/input/input1
>> [ 41.121279] ACPI: Power Button (CM) [PWRB]
>> [ 41.140593] Real Time Clock Driver v1.12ac
>> [ 41.140939] hpet_resources: 0xfed00000 is busy
>> [ 41.140970] Linux agpgart interface v0.102 (c) Dave Jones
>> [ 41.141204] tun: Universal TUN/TAP device driver, 1.6
>> [ 41.141367] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
>> [ 41.141551] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>> [ 41.141716] ide: Assuming 33MHz system bus speed for PIO modes; override
>> with idebus=xx
>> [ 41.142031] NFORCE-MCP65: IDE controller at PCI slot 0000:00:09.0
>> [ 41.142207] NFORCE-MCP65: chipset revision 161
>> [ 41.142371] NFORCE-MCP65: not 100% native mode: will probe irqs later
>> [ 41.142539] NFORCE-MCP65: 0000:00:09.0 (rev a1) UDMA133 controller
>> [ 41.142706] ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA,
>> hdb:pio
>> [ 41.143065] Probing IDE interface ide0...
>> [ 41.430036] hda: SAMSUNG SP1213N, ATA DISK drive
>> [ 42.071954] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>> [ 42.074576] hda: max request size: 512KiB
>> [ 42.074789] hda: 234493056 sectors (120060 MB) w/8192KiB Cache,
>> CHS=16383/255/63, UDMA(100)
>> [ 42.075551] hda: cache flushes supported
>> [ 42.075734] hda: hda1 hda2 hda3 < hda5 hda6 hda7 >
>> [ 42.116273] ahci 0000:00:0a.0: version 2.2
>> [ 42.116482] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
>> [ 42.116653] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23
>> (level, low) -> IRQ 23
>> [ 43.119478] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf
>> impl IDE mode
>> [ 43.119778] ahci 0000:00:0a.0: flags: 64bit led clo pmp pio
>> [ 43.119943] PCI: Setting latency timer of device 0000:00:0a.0 to 64
>> [ 43.120149] scsi0 : ahci
>> [ 43.120365] scsi1 : ahci
>> [ 43.120556] scsi2 : ahci
>> [ 43.120741] scsi3 : ahci
>> [ 43.120927] ata1: SATA max UDMA/133 cmd 0xffffc20000014100 ctl
>> 0x0000000000000000 bmdma 0x0000000000000000 irq 315
>> [ 43.121227] ata2: SATA max UDMA/133 cmd 0xffffc20000014180 ctl
>> 0x0000000000000000 bmdma 0x0000000000000000 irq 315
>> [ 43.121526] ata3: SATA max UDMA/133 cmd 0xffffc20000014200 ctl
>> 0x0000000000000000 bmdma 0x0000000000000000 irq 315
>> [ 43.121826] ata4: SATA max UDMA/133 cmd 0xffffc20000014280 ctl
>> 0x0000000000000000 bmdma 0x0000000000000000 irq 315
>> [ 43.934296] ata1: softreset failed (1st FIS failed)
>> [ 43.934461] ata1: reset failed (errno=-5), retrying in 10 secs
>> [ 53.885194] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> [ 53.885890] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133
>> [ 53.886056] ata1.00: 312581808 sectors, multi 16: LBA48
>> [ 53.886804] ata1.00: configured for UDMA/133
>> [ 54.201147] ata2: SATA link down (SStatus 0 SControl 300)
>> [ 54.517101] ata3: SATA link down (SStatus 0 SControl 300)
>> [ 54.833055] ata4: SATA link down (SStatus 0 SControl 300)
>> [ 54.833271] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0
>> PQ: 0 ANSI: 5
>> [ 54.833623] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042
>> MB)
>> [ 54.833793] sd 0:0:0:0: [sda] Write Protect is off
>> [ 54.833957] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
>> [ 54.833965] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
>> doesn't support DPO or FUA
>> [ 54.834287] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042
>> MB)
>> [ 54.834455] sd 0:0:0:0: [sda] Write Protect is off
>> [ 54.834619] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
>> [ 54.834626] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
>> doesn't support DPO or FUA
>> [ 54.834924] sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
>> [ 54.869055] sd 0:0:0:0: [sda] Attached SCSI disk
>> [ 54.869495] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
>> [ 54.869667] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 22
>> (level, low) -> IRQ 22
>> [ 54.870288] PCI: Setting latency timer of device 0000:00:02.1 to 64
>> [ 54.870293] ehci_hcd 0000:00:02.1: EHCI Host Controller
>> [ 54.870532] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus
>> number 1
>> [ 54.870848] ehci_hcd 0000:00:02.1: debug port 1
>> [ 54.871013] PCI: cache line size of 64 is not supported by device
>> 0000:00:02.1
>> [ 54.871022] ehci_hcd 0000:00:02.1: irq 22, io mem 0xf9dfec00
>> [ 54.871191] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10
>> Dec 2004
>> [ 54.871572] usb usb1: configuration #1 chosen from 1 choice
>> [ 54.871761] hub 1-0:1.0: USB hub found
>> [ 54.871927] hub 1-0:1.0: 10 ports detected
>> [ 54.976112] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI)
>> Driver
>> [ 54.976353] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 21
>> [ 54.976523] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUB0] -> GSI 21
>> (level, low) -> IRQ 21
>> [ 54.977020] PCI: Setting latency timer of device 0000:00:02.0 to 64
>> [ 54.977025] ohci_hcd 0000:00:02.0: OHCI Host Controller
>> [ 54.977260] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus
>> number 2
>> [ 54.977569] ohci_hcd 0000:00:02.0: irq 21, io mem 0xf9dff000
>> [ 55.034680] usb usb2: configuration #1 chosen from 1 choice
>> [ 55.034869] hub 2-0:1.0: USB hub found
>> [ 55.035037] hub 2-0:1.0: 10 ports detected
>> [ 55.139122] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64
>> irq 1,12
>> [ 55.142186] serio: i8042 KBD port at 0x60,0x64 irq 1
>> [ 55.142352] serio: i8042 AUX port at 0x60,0x64 irq 12
>> [ 55.142569] mice: PS/2 mouse device common for all mice
>> [ 55.169330] input: AT Translated Set 2 keyboard as /class/input/input2
>> [ 55.431622] usb 1-5: new high speed USB device using ehci_hcd and address 3
>> [ 55.566822] usb 1-5: configuration #1 chosen from 1 choice
>> [ 55.807525] usb 2-4: new full speed USB device using ohci_hcd and address 2
>> [ 55.963577] usb 2-4: configuration #1 chosen from 1 choice
>> [ 55.969539] hub 2-4:1.0: USB hub found
>> [ 55.972507] hub 2-4:1.0: 4 ports detected
>> [ 56.314740] usb 2-4.1: new full speed USB device using ohci_hcd and address
>> 3
>> [ 56.449493] usb 2-4.1: configuration #1 chosen from 1 choice
>> [ 56.669944] usb 2-4.3: new low speed USB device using ohci_hcd and address
>> 4
>> [ 56.783741] usb 2-4.3: configuration #1 chosen from 1 choice
>> [ 56.802767] input: Logitech USB-PS/2 Optical Mouse as /class/input/input3
>> [ 56.802968] input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on
>> usb-0000:00:02.0-4.3
>> [ 56.803327] usbcore: registered new interface driver usbhid
>> [ 56.803492] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
>> [ 56.803690] TCP cubic registered
>> [ 56.803861] NET: Registered protocol family 1
>> [ 56.804026] NET: Registered protocol family 17
>> [ 56.804201] powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor
>> 6000+ processors (version 2.00.00)
>> [ 56.804448] powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0x6
>> [ 56.804613] powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0x8
>> [ 56.804778] powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xa
>> [ 56.804943] powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0xc
>> [ 56.805107] powernow-k8: 4 : fid 0xe (2200 MHz), vid 0xe
>> [ 56.805272] powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10
>> [ 56.805437] powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10
>> [ 56.805602] powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12
>> [ 56.826551] ReiserFS: sda3: found reiserfs format "3.6" with standard
>> journal
>> [ 56.826720] ReiserFS: sda3: using ordered data mode
>> [ 56.836124] ReiserFS: sda3: journal params: device sda3, size 8192, journal
>> first block 18, max trans len 1024, max batch 900, max commit age 30, max
>> trans age 30
>> [ 56.837467] ReiserFS: sda3: checking transaction log (sda3)
>> [ 56.888740] ReiserFS: sda3: Using r5 hash to sort names
>> [ 56.888915] VFS: Mounted root (reiserfs filesystem) readonly.
>> [ 56.889092] Freeing unused kernel memory: 184k freed
>> [ 61.840593] ReiserFS: sda3: switching to journaled data mode
>> [ 62.230945] r8169 Gigabit Ethernet driver 2.2LK loaded
>> [ 62.231224] ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 19
>> [ 62.231232] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNEB] -> GSI 19
>> (level, low) -> IRQ 19
>> [ 62.231250] PCI: Setting latency timer of device 0000:01:00.0 to 64
>> [ 62.231430] eth0: RTL8168b/8111b at 0xffffc2000016c000, 00:19:66:47:f3:cb,
>> IRQ 19
>> [ 62.284221] HPT366: IDE controller at PCI slot 0000:02:0a.0
>> [ 62.284491] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 18
>> [ 62.284499] ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [LNKC] -> GSI 18
>> (level, low) -> IRQ 18
>> [ 62.284508] HPT366: chipset revision 1
>> [ 62.284514] HPT366: using 33 MHz PCI clock
>> [ 62.284516] HPT366: 100% native mode on irq 18
>> [ 62.284524] ide1: BM-DMA at 0xd000-0xd007, BIOS settings: hdc:pio,
>> hdd:pio
>> [ 62.284536] ACPI: PCI Interrupt 0000:02:0a.1[A] -> Link [LNKC] -> GSI 18
>> (level, low) -> IRQ 18
>> [ 62.284544] HPT366: using 33 MHz PCI clock
>> [ 62.284546] HPT366: too many IDE interfaces, no room in table
>> [ 62.284548] HPT366: neither IDE port enabled (BIOS)
>> [ 62.284551] Probing IDE interface ide1...
>> [ 62.988343] hdc: _NEC DVD_RW ND-3500AG, ATAPI CD/DVD-ROM drive
>> [ 63.630192] ide1 at 0xd480-0xd487,0xd402 on irq 18
>> [ 63.632589] hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
>> [ 63.632594] Uniform CD-ROM driver Revision: 3.20
>> [ 64.048482] reiser4: sda5: found disk format 4.0.0.
>> [ 69.431516] reiser4: sda6: found disk format 4.0.0.
>> [ 70.722395] reiser4: hda7: found disk format 4.0.0.
>> [ 71.428725] Adding 1951888k swap on /dev/sda2. Priority:-1 extents:1
>> across:1951888k
>> [ 74.227887] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 17
>> [ 74.227897] ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKB] -> GSI 17
>> (level, low) -> IRQ 17
>> [ 74.230613] Audigy2 value: Special config.
>> [ 78.048887] r8169: eth0: link up
>> [ 78.049039] r8169: eth0: link up
>> [ 82.597555] nvidia: module license 'NVIDIA' taints kernel.
>> [ 82.767839] ACPI: PCI Interrupt Link [LNED] enabled at IRQ 16
>> [ 82.767847] ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [LNED] -> GSI 16
>> (level, low) -> IRQ 16
>> [ 82.767853] PCI: Setting latency timer of device 0000:04:00.0 to 64
>> [ 82.767943] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 100.14.23 Thu
>> Oct 4 10:27:34 PDT 2007
>>
>> Glück Auf,
>> Volker
>>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-ide" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
tejun
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/