[regression] pciehp hang on hp ia64 rx6600

From: Alex Chiang
Date: Wed Mar 12 2008 - 02:48:28 EST

Next message: Huang, Ying: "Re: [PATCH -mm] kexec jump -v9"
Previous message: Tetsuo Handa: "Re: [2.6.25-rc5-mm1] BUG() at mnt_want_write()."
Next in thread: Mark Lord: "Re: [regression] pciehp hang on hp ia64 rx6600"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hi Mark, Kristin,

On my hp ia64 rx6600, 'modprobe pciehp' causes lockups and a
system hang on 2.6.25-rc4. My system often hangs when only pciehp
is loaded and my console is sitting idle, but I can accelerate
the hang 100% of the time by immediately doing a 'modprobe
acpiphp' right afterwards.

I have bisected the hang down to this commit:

0a3c33d77ff7ad5b988997536a8f09c49e35ad20 is first bad commit
commit 0a3c33d77ff7ad5b988997536a8f09c49e35ad20
Author: Mark Lord <lkml@xxxxxx>
Date: Wed Nov 28 15:11:28 2007 -0800

PCIE: fix PCIe Hotplug so that it works with ExpressCard slots on Dell notebooks (and others?) in conjunction with modparam of pciehp_force=1.

Fix pciehp_probe() to deal with ExpressCard cards
that were inserted prior to the driver being loaded.

Signed-off-by: Mark Lord <mlord@xxxxxxxxx>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@xxxxxxxxx>
Cc: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
Cc: Theodore Ts'o <tytso@xxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxx>

:040000 040000 5fe9142c7d2add2db2891a8f469159e338e1c4e4 cd147cb51d7a2133679dd57796044c680159dab7 M drivers

Reverting this commit makes the hang go away (and I can modprobe
pciehp / acpiphp again without problems).

It looks like the patch is calling pciehp_enable_slot() if the
slot is occupied. I'm not sure exactly what should be happening
on my machine (it's late here ;), but I can try and do some more
thinking tomorrow.

Console log and lspci -vv output follows. Please let me know what
else you might need.

Thanks.

/ac

[root@canola ~]# dmesg -n 8
[root@canola ~]# modprobe pciehp
pciehp: HPC vendor_id 103c device_id 403b ss_vid 0 ss_did 0
pciehp: pciehp_enable_slot: already enabled on slot(0016_0006)
Load service driver hpdriver on pcie device 0000:0f:00.0:pcie02
pciehp: HPC vendor_id 111d device_id 801c ss_vid 0 ss_did 0
pciehp: pciehp_enable_slot: already enabled on slot(0082_0004)
Load service driver hpdriver on pcie device 0000:51:00.0:pcie22
pciehp: HPC vendor_id 111d device_id 801c ss_vid 0 ss_did 0
pciehp: pciehp_enable_slot: latch open on slot(0139_0003)
Load service driver hpdriver on pcie device 0000:51:01.0:pcie22
pciehp: HPC vendor_id 103c device_id 403b ss_vid 0 ss_did 0
Load service driver hpdriver on pcie device 0000:c4:00.0:pcie02
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[root@canola ~]# modprobe acpiphp
INFO: task rsyslogd:3753 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
rsyslogd D a00000010023cec0 0 3753 1

Call Trace:
[<a0000001007d3c20>] schedule+0x1200/0x1400
sp=e0000005167afcf0 bsp=e0000005167a1018
[<a00000010023cec0>] log_wait_commit+0x140/0x220
sp=e0000005167afd80 bsp=e0000005167a0fd8
[<a00000010022f710>] journal_stop+0x430/0x4e0
sp=e0000005167afdb0 bsp=e0000005167a0f90
[<a000000100230f40>] journal_force_commit+0x80/0xa0
sp=e0000005167afdb0 bsp=e0000005167a0f70
[<a00000010021ffc0>] ext3_force_commit+0x60/0x80
sp=e0000005167afdb0 bsp=e0000005167a0f50
[<a0000001002126e0>] ext3_write_inode+0xa0/0xc0
sp=e0000005167afdb0 bsp=e0000005167a0f28
[<a0000001001a23b0>] __writeback_single_inode+0x4b0/0x740
sp=e0000005167afdb0 bsp=e0000005167a0ee0
[<a0000001001a3ae0>] sync_inode+0x40/0x80
sp=e0000005167afdf0 bsp=e0000005167a0eb0
[<a0000001002098f0>] ext3_sync_file+0x1b0/0x220
sp=e0000005167afdf0 bsp=e0000005167a0e88
[<a0000001001a9700>] do_fsync+0xe0/0x180
sp=e0000005167afe30 bsp=e0000005167a0e48
[<a0000001001a97f0>] __do_fsync+0x50/0x80
sp=e0000005167afe30 bsp=e0000005167a0e18
[<a0000001001a98b0>] sys_fsync+0x30/0x60
sp=e0000005167afe30 bsp=e0000005167a0db8
[<a00000010000a980>] ia64_ret_from_syscall+0x0/0x20
sp=e0000005167afe30 bsp=e0000005167a0db8
[<a000000000010720>] __kernel_syscall_via_break+0x0/0x20
sp=e0000005167b0000 bsp=e0000005167a0db8

[more soft lockup output, then my console becomes unresponsive, needs
hard system reset]

[root@canola ~]# lspci -vv
00:01.0 Class ff00: Hewlett-Packard Company RMP-3 (Remote Management Processor)
Subsystem: Hewlett-Packard Company RMP-3 (Remote Management Processor)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (250ns max), Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 0
Capabilities: [e8] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable-
Address: 0000000000000000 Data: 0000

00:01.1 Communication controller: Hewlett-Packard Company RMP-3 Shared Memory Driver
Subsystem: Hewlett-Packard Company RMP-3 Shared Memory Driver
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (250ns max), Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 0
Region 1: Memory at 84034000 (64-bit, non-prefetchable) [size=4K]
Region 3: Memory at 80080000000 (64-bit, prefetchable) [size=128K]
Capabilities: [e8] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable-
Address: 0000000000000000 Data: 0000

00:01.2 Serial controller: Hewlett-Packard Company Diva Serial [GSP] Multiport UART (prog-if 02 [16550])
Subsystem: Hewlett-Packard Company Diva RMP3
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (250ns max), Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 59
Region 1: Memory at 84033000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [e8] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable-
Address: 0000000000000000 Data: 0000

00:02.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: Unknown device 03f0:0226
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (250ns min, 10500ns max), Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 61
Region 0: Memory at 84032000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:02.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: Unknown device 03f0:0226
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (250ns min, 10500ns max), Cache Line Size: 128 bytes
Interrupt: pin B routed to IRQ 62
Region 0: Memory at 84031000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:02.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
Subsystem: Unknown device 03f0:0326
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4000ns min, 8500ns max), Cache Line Size: 128 bytes
Interrupt: pin C routed to IRQ 60
Region 0: Memory at 84030000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:04.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE] (prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company Radeon 7000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (2000ns min), Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 58
Region 0: Memory at 80000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at 1001000 [size=256]
Region 2: Memory at 84020000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at 84000000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0f:00.0 PCI bridge: Hewlett-Packard Company PCIe Root Port (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 128 bytes
Bus: primary=0f, secondary=10, subordinate=48, sec-latency=0
I/O behind bridge: 00001000-0000ffff
Memory behind bridge: b0000000-bfffffff
Prefetchable memory behind bridge: 0000080380000000-00000803ffffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000fee00000 Data: 4033
Capabilities: [60] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 0
Link: Latency L0s <1us, L1 <16us
Link: ASPM Disabled RCB 128 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Slot: AtnBtn+ PwrCtrl+ MRL+ AtnInd+ PwrInd+ HotPlug+ Surpise-
Slot: Number 6, PowerLimit 25.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq+
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Advanced Error Reporting
Capabilities: [150] Unknown (11)

10:00.0 RAID bus controller: Hewlett-Packard Company Smart Array Controller (rev 03)
Subsystem: Hewlett-Packard Company E500 SAS Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 50
Region 0: Memory at b0000000 (64-bit, non-prefetchable) [size=1M]
Region 2: I/O ports at 4001000 [size=256]
Region 3: Memory at b0140000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at b0100000 [disabled] [size=256K]
Capabilities: [b0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 512 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 2048 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s <2us, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [d4] MSI-X: Enable+ Mask- TabSize=4
Vector table: BAR=0 offset=000fe000
PBA: BAR=0 offset=000ff000
Capabilities: [e0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [ec] Vital Product Data
Capabilities: [100] Power Budgeting

49:02.0 Ethernet controller: Intel Corporation 82546GB Gigabit Ethernet Controller (rev 03)
Subsystem: Hewlett-Packard Company Core Dual Port 1000Base-T [AB352A]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 76
Region 0: Memory at c0120000 (64-bit, non-prefetchable) [size=128K]
Region 2: Memory at c00c0000 (64-bit, non-prefetchable) [size=256K]
Region 4: I/O ports at 5001040 [size=64]
Expansion ROM at c0080000 [disabled] [size=256K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=4096 OST=4
Status: Dev=49:02.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
Capabilities: [f0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000

49:02.1 Ethernet controller: Intel Corporation 82546GB Gigabit Ethernet Controller (rev 03)
Subsystem: Hewlett-Packard Company Core Dual Port 1000Base-T [AB352A]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), Cache Line Size: 128 bytes
Interrupt: pin B routed to IRQ 77
Region 0: Memory at c0100000 (64-bit, non-prefetchable) [size=128K]
Region 2: Memory at c0040000 (64-bit, non-prefetchable) [size=256K]
Region 4: I/O ports at 5001000 [size=64]
Expansion ROM at c0000000 [disabled] [size=256K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=4096 OST=4
Status: Dev=49:02.1 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
Capabilities: [f0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000

4f:00.0 PCI bridge: Hewlett-Packard Company PCIe Root Port (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 128 bytes
Bus: primary=4f, secondary=50, subordinate=c3, sec-latency=0
I/O behind bridge: 00001000-0000ffff
Memory behind bridge: e0000000-efffffff
Prefetchable memory behind bridge: 0000080680000000-00000806ffffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000fee00000 Data: 4035
Capabilities: [60] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 0
Link: Latency L0s <1us, L1 <16us
Link: ASPM Disabled RCB 128 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Advanced Error Reporting
Capabilities: [150] Unknown (11)

50:00.0 PCI bridge: Integrated Device Technology, Inc. Unknown device 801c (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 128 bytes
Bus: primary=50, secondary=51, subordinate=c3, sec-latency=0
I/O behind bridge: 00001000-0000ffff
Memory behind bridge: e0000000-efffffff
Prefetchable memory behind bridge: 0000080680000000-00000806ffffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Upstream Port IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn+ AtnInd+ PwrInd+
Device: SlotPowerLimit 0.000000
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 0
Link: Latency L0s <2us, L1 <4us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel

51:00.0 PCI bridge: Integrated Device Technology, Inc. Unknown device 801c (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 128 bytes
Bus: primary=51, secondary=52, subordinate=8a, sec-latency=0
I/O behind bridge: 00001000-00008fff
Memory behind bridge: e8000000-efffffff
Prefetchable memory behind bridge: 0000080680000000-00000806bfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Downstream Port (Slot+) IRQ 0
Device: Supported: MaxPayload 2048 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 1
Link: Latency L0s <2us, L1 <4us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Slot: AtnBtn+ PwrCtrl+ MRL+ AtnInd+ PwrInd+ HotPlug+ Surpise-
Slot: Number 4, PowerLimit 25.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq+
Slot: AttnInd Off, PwrInd On, Power-
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [7c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee00000 Data: 4036
Capabilities: [100] Virtual Channel

51:01.0 PCI bridge: Integrated Device Technology, Inc. Unknown device 801c (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 128 bytes
Bus: primary=51, secondary=8b, subordinate=c3, sec-latency=0
I/O behind bridge: 00009000-0000ffff
Memory behind bridge: e0000000-e7ffffff
Prefetchable memory behind bridge: 00000806c0000000-00000806ffffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Downstream Port (Slot+) IRQ 0
Device: Supported: MaxPayload 2048 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 2
Link: Latency L0s <2us, L1 <4us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Slot: AtnBtn+ PwrCtrl+ MRL+ AtnInd+ PwrInd+ HotPlug+ Surpise-
Slot: Number 3, PowerLimit 25.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq+
Slot: AttnInd Off, PwrInd On, Power-
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [7c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee00000 Data: 4037
Capabilities: [100] Virtual Channel

52:00.0 RAID bus controller: Hewlett-Packard Company Smart Array Controller (rev 03)
Subsystem: Hewlett-Packard Company Smart Array P800
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 52
Region 0: Memory at e8000000 (64-bit, non-prefetchable) [size=1M]
Region 2: I/O ports at 7001000 [size=256]
Region 3: Memory at e8140000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at e8100000 [disabled] [size=256K]
Capabilities: [b0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 512 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 2048 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s <2us, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [d4] MSI-X: Enable+ Mask- TabSize=4
Vector table: BAR=0 offset=000fe000
PBA: BAR=0 offset=000ff000
Capabilities: [e0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [ec] Vital Product Data
Capabilities: [100] Power Budgeting

8b:00.0 RAID bus controller: Hewlett-Packard Company Smart Array Controller (rev 03)
Subsystem: Hewlett-Packard Company P400 SAS Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 71
Region 0: Memory at e0000000 (64-bit, non-prefetchable) [size=1M]
Region 2: I/O ports at 7009000 [size=256]
Region 3: Memory at e0140000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at e0100000 [disabled] [size=256K]
Capabilities: [b0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 512 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 2048 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s <2us, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [d4] MSI-X: Enable+ Mask- TabSize=4
Vector table: BAR=0 offset=000fe000
PBA: BAR=0 offset=000ff000
Capabilities: [e0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [ec] Vital Product Data
Capabilities: [100] Power Budgeting

c4:00.0 PCI bridge: Hewlett-Packard Company PCIe Root Port (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 128 bytes
Bus: primary=c4, secondary=c5, subordinate=fe, sec-latency=0
I/O behind bridge: 00001000-0000ffff
Memory behind bridge: f0000000-fdffffff
Prefetchable memory behind bridge: 0000080780000000-00000807ffffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000fee00000 Data: 4039
Capabilities: [60] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 0
Link: Latency L0s <1us, L1 <16us
Link: ASPM Disabled RCB 128 bytes Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Slot: AtnBtn+ PwrCtrl+ MRL+ AtnInd+ PwrInd+ HotPlug+ Surpise-
Slot: Number 5, PowerLimit 25.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq+
Slot: AttnInd Off, PwrInd Off, Power+
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Advanced Error Reporting
Capabilities: [150] Unknown (11)

[root@canola ~]# lspci -vt
-+-[0000:c4]---00.0-[0000:c5-fe]--
+-[0000:4f]---00.0-[0000:50-c3]----00.0-[0000:51-c3]--+-00.0-[0000:52-8a]----00.0 Hewlett-Packard Company Smart Array Controller
| \-01.0-[0000:8b-c3]----00.0 Hewlett-Packard Company Smart Array Controller
+-[0000:49]-+-02.0 Intel Corporation 82546GB Gigabit Ethernet Controller
| \-02.1 Intel Corporation 82546GB Gigabit Ethernet Controller
+-[0000:0f]---00.0-[0000:10-48]----00.0 Hewlett-Packard Company Smart Array Controller
\-[0000:00]-+-01.0 Hewlett-Packard Company RMP-3 (Remote Management Processor)
+-01.1 Hewlett-Packard Company RMP-3 Shared Memory Driver
+-01.2 Hewlett-Packard Company Diva Serial [GSP] Multiport UART
+-02.0 NEC Corporation USB
+-02.1 NEC Corporation USB
+-02.2 NEC Corporation USB 2.0
\-04.0 ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE]

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Huang, Ying: "Re: [PATCH -mm] kexec jump -v9"
Previous message: Tetsuo Handa: "Re: [2.6.25-rc5-mm1] BUG() at mnt_want_write()."
Next in thread: Mark Lord: "Re: [regression] pciehp hang on hp ia64 rx6600"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]