pata_it821x completely broken

[Ondrej Zary]

Hello,
after a total hard disk failure, I decided to build RAID1 using a cheap card 
with it8212 chip and two Samsung HD400LD drives. I thought that the 
pata_it821x driver is mature and should work fine (it does not depend on 
EXPERIMENTAL). However, it seems to be broken in several ways (in 2.6.25.3).

When I don't have any RAID array created, both drives are detected but it 
appears to work only in MWDMA2 mode:

pata_it821x: controller in smart mode.
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> 
IRQ 11
PCI: Setting latency timer of device 0000:00:12.0 to 64
scsi2 : pata_it821x
scsi3 : pata_it821x
ata3: PATA max MWDMA2 cmd 0x6800 ctl 0x6c00 bmdma 0x7800 irq 11
ata4: PATA max MWDMA2 cmd 0x7000 ctl 0x7400 bmdma 0x7808 irq 11
ata3.00: ATA-7: SAMSUNG HD400LD, WQ100-15, max UDMA/100
ata3.00: 781422768 sectors, multi 0: LBA48
ata3.00: configured for DMA
ata4.00: ATA-7: SAMSUNG HD400LD, WQ100-15, max UDMA/100
ata4.00: 781422768 sectors, multi 0: LBA48
ata4.00: configured for DMA

But in fact, it's running faster:
hdparm --direct -t /dev/sdc

/dev/sdc:
 Timing O_DIRECT disk reads:  188 MB in  3.01 seconds =  62.48 MB/sec


Also I get some errors about HPA when rebooting but haven't captured them yet. 


But the more interesting thing is that once I create a RAID1 array (and run 
background rebuild), the driver does not work anymore:

ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> 
IRQ 11
scsi2 : pata_it821x
scsi3 : pata_it821x
ata3: PATA max MWDMA2 cmd 0x6800 ctl 0x6c00 bmdma 0x7800 irq 11
ata4: PATA max MWDMA2 cmd 0x7000 ctl 0x7400 bmdma 0x7808 irq 11
ata3.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_masl=0x80)
ata3: failed to recover some devices, retrying in 5 secs
ata3.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_masl=0x80)
ata3: failed to recover some devices, retrying in 5 secs
ata3.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_masl=0x80)
ata3: failed to recover some devices, retrying in 5 secs


I'm going to start debugging, suggestions are welcome.

-- 
Ondrej Zary
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/