Re: sata error on ICH8M (Dell Vostro 1710 laptop)
From: Tim Connors
Date: Tue Nov 04 2008 - 06:53:18 EST
On Tue, 4 Nov 2008, Tim Connors wrote:
> I'm running a debian 2.6.26-9 kernel (sid) on a new laptop with:
> 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 03) (prog-if 01 [AHCI 1.0])
> Subsystem: Dell Device 0275
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin B routed to IRQ 378
> Region 0: I/O ports at 1c00 [size=8]
> Region 1: I/O ports at 18d4 [size=4]
> Region 2: I/O ports at 18d8 [size=8]
> Region 3: I/O ports at 18d0 [size=4]
> Region 4: I/O ports at 18e0 [size=32]
> Region 5: Memory at f8504000 (32-bit, non-prefetchable) [size=2K]
> Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/2 Enable+
> Address: fee0300c Data: 41a1
> Capabilities: [70] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [a8] SATA HBA <?>
> Kernel driver in use: ahci
> Kernel modules: ahci
hdparm -I and dmesg from a fresh bootup are attached.
I have not set anything using hdparm beyond standard debian install, which
notably does set 'hdparm -B 254'.
--
TimC
There's only one way to better your memory. Everytime you forget
something, poke your brain with a stick. That'll teach it. -- Ash
/dev/sda:
ATA device, with non-removable media
Model Number: ST9160310AS
Serial Number: 5SV1ELVY
Firmware Revision: DE04
Transport: Serial
Standards:
Used: unknown (minor revision code 0x0029)
Supported: 8 7 6 5
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 312581808
device size with M = 1024*1024: 152627 MBytes
device size with M = 1000*1000: 160041 MBytes (160 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: 254
Recommended acoustic management value: 208, current value: 208
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
SET_MAX security extension
* Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* Media Card Pass-Through
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* WRITE_DMA_QUEUED_FUA_EXT
* 64-bit World wide name
* URG for READ_STREAM[_DMA]_EXT
* URG for WRITE_STREAM[_DMA]_EXT
Time Limited Commands (TLC) feature set
Command Completion Time Limit (CCTL)
* IDLE_IMMEDIATE with UNLOAD
* Write-Read-Verify feature set
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
Segmented DOWNLOAD_MICROCODE
* SATA-I signaling speed (1.5Gb/s)
* SATA-II signaling speed (3.0Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
DMA Setup Auto-Activate optimization
* Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12] (vendor specific)
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
supported: enhanced erase
52min for SECURITY ERASE UNIT. 52min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 5000c500e473341
NAA : 5
IEEE OUI : c50
Unique ID : 0e473341
Checksum: correct
[ 0.000000] Linux version 2.6.26 (2.6.26) (root@gamow) (gcc version 4.3.2 (Debian 4.3.2-1) ) #4 SMP Mon Nov 3 22:35:21 EST 2008
[ 0.000000] Command line: root=/dev/mapper/gamow-root ro quiet
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000bf6d0000 (usable)
[ 0.000000] BIOS-e820: 00000000bf6d0000 - 00000000bf6e3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000bf6e3000 - 00000000c0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 784080) 1 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 1048576, 1310720) 2 entries of 3200 used
[ 0.000000] max_pfn_mapped = 1310720
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] init_memory_mapping
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F7660, 0024 (r2 DELL )
[ 0.000000] ACPI: XSDT BF6D66F5, 009C (r1 DELL M08 6040000 LTP 0)
[ 0.000000] ACPI: FACP BF6DEB60, 00F4 (r3 TOSCPL CRESTLNE 6040000 ALAN 1)
[ 0.000000] ACPI: DSDT BF6D7C3B, 6EB1 (r2 TOSCPL CRESTLNE 6040000 INTL 20060608)
[ 0.000000] ACPI: FACS BF6E2FC0, 0040
[ 0.000000] ACPI: APIC BF6DEC54, 0068 (r1 INTEL CRESTLNE 6040000 LOHR 5A)
[ 0.000000] ACPI: HPET BF6DECBC, 0038 (r1 INTEL CRESTLNE 6040000 LOHR 5A)
[ 0.000000] ACPI: MCFG BF6DECF4, 003C (r1 INTEL CRESTLNE 6040000 LOHR 5A)
[ 0.000000] ACPI: TCPA BF6DED30, 0032 (r1 Intel CRESTLNE 6040000 LOHR 5A)
[ 0.000000] ACPI: TMOR BF6DED62, 0026 (r1 PTLTD 6040000 PTL 3)
[ 0.000000] ACPI: OSFR BF6DED88, 0072 (r1 TOSHIB A+2nd ID 6040000 TASM 4010000)
[ 0.000000] ACPI: APIC BF6DEDFA, 0068 (r1 PTLTD APIC 6040000 LTP 0)
[ 0.000000] ACPI: BOOT BF6DEE62, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
[ 0.000000] ACPI: SLIC BF6DEE8A, 0176 (r1 DELL M08 6040000 LTP 0)
[ 0.000000] ACPI: SSDT BF6D798E, 02AD (r1 SataRe SataAhci 1000 INTL 20061109)
[ 0.000000] ACPI: SSDT BF6D78EB, 00A3 (r1 BrtRef DD01BRT 1000 INTL 20061109)
[ 0.000000] ACPI: SSDT BF6D6D1D, 025F (r1 PmRef Cpu0Tst 3000 INTL 20061109)
[ 0.000000] ACPI: SSDT BF6D6C77, 00A6 (r1 PmRef Cpu1Tst 3000 INTL 20061109)
[ 0.000000] ACPI: SSDT BF6D6791, 04E6 (r1 PmRef CpuPm 3000 INTL 20061109)
[ 0.000000] ACPI: BIOS bug: multiple APIC/MADT found, using 0
[ 0.000000] ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@xxxxxxxxxxxxxxx
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-0000000140000000
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 784080) 1 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 1048576, 1310720) 2 entries of 3200 used
[ 0.000000] Bootmem setup node 0 0000000000000000-0000000140000000
[ 0.000000] NODE_DATA [0000000000001000 - 0000000000004fff]
[ 0.000000] bootmap [000000000000e000 - 0000000000035fff] pages 28
[ 0.000000] early res: 0 [0-fff] BIOS data page
[ 0.000000] early res: 1 [6000-7fff] TRAMPOLINE
[ 0.000000] early res: 2 [200000-68c487] TEXT DATA BSS
[ 0.000000] early res: 3 [37886000-37fef006] RAMDISK
[ 0.000000] early res: 4 [9f800-fffff] BIOS reserved
[ 0.000000] early res: 5 [8000-dfff] PGTABLE
[ 0.000000] [ffffe20000000000-ffffe20003bfffff] PMD -> [ffff810001200000-ffff810003ffffff] on node 0
[ 0.000000] [ffffe20003c00000-ffffe200045fffff] PMD -> [ffff81000c000000-ffff81000c9fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1310720
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0 -> 159
[ 0.000000] 0: 256 -> 784080
[ 0.000000] 0: 1048576 -> 1310720
[ 0.000000] On node 0 totalpages: 1046127
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 1271 pages reserved
[ 0.000000] DMA zone: 2672 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 765704 pages, LIFO batch:31
[ 0.000000] Normal zone: 3584 pages used for memmap
[ 0.000000] Normal zone: 258560 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000
[ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000bf6d0000 - 00000000bf6e3000
[ 0.000000] PM: Registered nosave memory: 00000000bf6e3000 - 00000000c0000000
[ 0.000000] PM: Registered nosave memory: 00000000c0000000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
[ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec10000
[ 0.000000] PM: Registered nosave memory: 00000000fec10000 - 00000000fed00000
[ 0.000000] PM: Registered nosave memory: 00000000fed00000 - 00000000fed14000
[ 0.000000] PM: Registered nosave memory: 00000000fed14000 - 00000000fed1a000
[ 0.000000] PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
[ 0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed90000
[ 0.000000] PM: Registered nosave memory: 00000000fed90000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ff000000
[ 0.000000] PM: Registered nosave memory: 00000000ff000000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 32496 bytes of per cpu data
[ 0.000000] NR_CPUS: 4, nr_cpu_ids: 2
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1026936
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: root=/dev/mapper/gamow-root ro quiet
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] TSC calibrated against PM_TIMER
[ 0.000000] time.c: Detected 1795.508 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Checking aperture...
[ 0.004000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.004000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.004000] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.004000] Placing software IO TLB between 0x4000000 - 0x8000000
[ 0.004000] Memory: 4048496k/5242880k available (2281k kernel code, 136012k reserved, 1385k data, 340k init)
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.004000] hpet clockevent registered
[ 0.083946] Calibrating delay using timer specific routine.. 3594.81 BogoMIPS (lpj=7189621)
[ 0.083986] Security Framework initialized
[ 0.083992] SELinux: Disabled at boot.
[ 0.083996] Capability LSM initialized
[ 0.084005] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.084005] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.085142] Mount-cache hash table entries: 256
[ 0.085328] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.085331] CPU: L2 cache: 2048K
[ 0.085333] CPU 0/0 -> Node 0
[ 0.085335] CPU: Physical Processor ID: 0
[ 0.085336] CPU: Processor Core ID: 0
[ 0.085342] CPU0: Thermal monitoring handled by SMI
[ 0.085344] using mwait in idle threads.
[ 0.085364] ACPI: Core revision 20080321
[ 0.140008] CPU0: Intel(R) Core(TM)2 Duo CPU T5670 @ 1.80GHz stepping 0d
[ 0.140008] Using local APIC timer interrupts.
[ 0.144009] APIC timer calibration result 12468793
[ 0.144009] Detected 12.468 MHz APIC timer.
[ 0.144009] Booting processor 1/1 ip 6000
[ 0.152009] Initializing CPU#1
[ 0.152009] Calibrating delay using timer specific routine.. 3591.06 BogoMIPS (lpj=7182132)
[ 0.152009] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.152009] CPU: L2 cache: 2048K
[ 0.152009] CPU 1/1 -> Node 0
[ 0.152009] CPU: Physical Processor ID: 0
[ 0.152009] CPU: Processor Core ID: 1
[ 0.152009] CPU1: Thermal monitoring enabled (TM2)
[ 0.152009] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
[ 0.232014] CPU1: Intel(R) Core(TM)2 Duo CPU T5670 @ 1.80GHz stepping 0d
[ 0.232014] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.236014] Brought up 2 CPUs
[ 0.236014] Total of 2 processors activated (7185.87 BogoMIPS).
[ 0.236014] CPU0 attaching sched-domain:
[ 0.236014] domain 0: span 0-1
[ 0.236014] groups: 0 1
[ 0.236014] domain 1: span 0-1
[ 0.236014] groups: 0-1
[ 0.236014] CPU1 attaching sched-domain:
[ 0.236014] domain 0: span 0-1
[ 0.236014] groups: 1 0
[ 0.236014] domain 1: span 0-1
[ 0.236014] groups: 0-1
[ 0.236014] net_namespace: 1192 bytes
[ 0.236014] NET: Registered protocol family 16
[ 0.236014] ACPI: bus type pci registered
[ 0.236014] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.236014] PCI: MCFG area at e0000000 reserved in E820
[ 0.248015] PCI: Using MMCONFIG at e0000000 - efffffff
[ 0.248015] PCI: Using configuration type 1 for base access
[ 0.248936] ACPI: EC: Look up EC in DSDT
[ 0.256016] ACPI: BIOS _OSI(Linux) query ignored
[ 0.256016] ACPI: DMI System Vendor: Dell Inc.
[ 0.256016] ACPI: DMI Product Name: Vostro1710
[ 0.256016] ACPI: DMI Product Version: Null
[ 0.256016] ACPI: DMI Board Name:
[ 0.256016] ACPI: DMI BIOS Vendor: Dell Inc.
[ 0.256016] ACPI: DMI BIOS Date: 09/09/2008
[ 0.256016] ACPI: Please send DMI info above to linux-acpi@xxxxxxxxxxxxxxx
[ 0.256016] ACPI: If "acpi_osi=Linux" works better, please notify linux-acpi@xxxxxxxxxxxxxxx
[ 0.256016] ACPI: Interpreter enabled
[ 0.256016] ACPI: (supports S0 S3 S4 S5)
[ 0.256016] ACPI: Using IOAPIC for interrupt routing
[ 0.261219] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 0.375222] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[ 0.375222] ACPI: EC: driver started in interrupt mode
[ 0.375222] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.375222] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.375222] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
[ 0.377926] PCI: Transparent bridge - 0000:00:1e.0
[ 0.377979] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.379222] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.379403] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.379583] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[ 0.379761] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
[ 0.379902] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.395903] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15)
[ 0.395903] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.395903] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 0.395903] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.395903] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[ 0.395903] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.395903] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 0.395903] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.395903] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.395903] pnp: PnP ACPI init
[ 0.395903] ACPI: bus type pnp registered
[ 0.395903] pnp 00:00: parse allocated resources
[ 0.395903] pnp 00:00: add io 0xcf8-0xcff flags 0x1
[ 0.395903] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.395903] pnp 00:01: parse allocated resources
[ 0.395903] pnp 00:01: add mem 0xfed1c000-0xfed1ffff flags 0x1
[ 0.395903] pnp 00:01: add mem 0xfed14000-0xfed17fff flags 0x1
[ 0.395903] pnp 00:01: add mem 0xfed18000-0xfed18fff flags 0x1
[ 0.395903] pnp 00:01: add mem 0xfed19000-0xfed19fff flags 0x1
[ 0.395903] pnp 00:01: add mem 0xe0000000-0xefffffff flags 0x1
[ 0.395903] pnp 00:01: add mem 0xfed20000-0xfed3ffff flags 0x1
[ 0.395903] pnp 00:01: add mem 0xfed40000-0xfed44fff flags 0x1
[ 0.395903] pnp 00:01: add mem 0xfed45000-0xfed8ffff flags 0x1
[ 0.395903] pnp 00:01: PNP0c02: calling quirk_system_pci_resources+0x0/0x15a
[ 0.395903] pnp 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.396439] pnp 00:02: parse allocated resources
[ 0.396446] pnp 00:02: add io 0x0-0x1f flags 0x1
[ 0.396448] pnp 00:02: add io 0x81-0x91 flags 0x1
[ 0.396450] pnp 00:02: add io 0x93-0x9f flags 0x1
[ 0.396452] pnp 00:02: add io 0xc0-0xdf flags 0x1
[ 0.396455] pnp 00:02: add dma 4 flags 0x1
[ 0.399903] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.399903] pnp 00:03: parse allocated resources
[ 0.399903] pnp 00:03: add mem 0xff000000-0xffffffff flags 0x0
[ 0.399903] pnp 00:03: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.399903] pnp 00:04: parse allocated resources
[ 0.399903] pnp 00:04: add mem 0xfed00000-0xfed003ff flags 0x0
[ 0.399903] pnp 00:04: PNP0c01: calling quirk_system_pci_resources+0x0/0x15a
[ 0.399903] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[ 0.399903] pnp 00:05: parse allocated resources
[ 0.399903] pnp 00:05: add io 0xf0-0xf0 flags 0x1
[ 0.399903] pnp 00:05: add irq 13 flags 0x1
[ 0.399903] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.399903] pnp 00:06: parse allocated resources
[ 0.399903] pnp 00:06: add io 0x2e-0x2f flags 0x1
[ 0.399903] pnp 00:06: add io 0x61-0x61 flags 0x1
[ 0.399903] pnp 00:06: add io 0x63-0x63 flags 0x1
[ 0.399903] pnp 00:06: add io 0x65-0x65 flags 0x1
[ 0.399903] pnp 00:06: add io 0x67-0x67 flags 0x1
[ 0.399903] pnp 00:06: add io 0x80-0x80 flags 0x1
[ 0.399903] pnp 00:06: add io 0x92-0x92 flags 0x1
[ 0.399903] pnp 00:06: add io 0xb2-0xb3 flags 0x1
[ 0.399903] pnp 00:06: add io 0x680-0x69f flags 0x1
[ 0.399903] pnp 00:06: add io 0x800-0x80f flags 0x1
[ 0.399903] pnp 00:06: add io 0x1000-0x107f flags 0x1
[ 0.399903] pnp 00:06: add io 0x1180-0x11bf flags 0x1
[ 0.399903] pnp 00:06: add io 0xfe00-0xfe00 flags 0x1
[ 0.399903] pnp 00:06: add io 0xff00-0xff7f flags 0x1
[ 0.399903] pnp 00:06: PNP0c02: calling quirk_system_pci_resources+0x0/0x15a
[ 0.399903] pnp 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.399903] pnp 00:07: parse allocated resources
[ 0.399903] pnp 00:07: add io 0x70-0x77 flags 0x1
[ 0.399903] pnp 00:07: add irq 8 flags 0x1
[ 0.399903] pnp 00:07: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.428098] pnp 00:08: parse allocated resources
[ 0.428104] pnp 00:08: add io 0x60-0x60 flags 0x1
[ 0.428107] pnp 00:08: add io 0x64-0x64 flags 0x1
[ 0.428112] pnp 00:08: add irq 1 flags 0x1
[ 0.431905] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.431905] pnp 00:09: parse allocated resources
[ 0.431905] pnp 00:09: add irq 12 flags 0x1
[ 0.431905] pnp 00:09: Plug and Play ACPI device, IDs SYN0705 SYN0700 SYN0002 PNP0f13 (active)
[ 0.431905] pnp: PnP ACPI: found 10 devices
[ 0.431905] ACPI: ACPI bus type pnp unregistered
[ 0.431905] usbcore: registered new interface driver usbfs
[ 0.431905] usbcore: registered new interface driver hub
[ 0.431905] usbcore: registered new device driver usb
[ 0.431905] PCI: Using ACPI for IRQ routing
[ 0.442580] NET: Registered protocol family 8
[ 0.442583] NET: Registered protocol family 20
[ 0.443949] PCI-GART: No AMD northbridge found.
[ 0.443949] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.443949] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.443949] ACPI: RTC can wake from S4
[ 0.454764] pnp: the driver 'system' has been registered
[ 0.454775] system 00:01: iomem range 0xfed1c000-0xfed1ffff could not be reserved
[ 0.454778] system 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved
[ 0.454782] system 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved
[ 0.454785] system 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved
[ 0.454788] system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
[ 0.454791] system 00:01: iomem range 0xfed20000-0xfed3ffff could not be reserved
[ 0.454794] system 00:01: iomem range 0xfed40000-0xfed44fff could not be reserved
[ 0.454797] system 00:01: iomem range 0xfed45000-0xfed8ffff could not be reserved
[ 0.454799] system 00:01: driver attached
[ 0.454808] system 00:04: iomem range 0xfed00000-0xfed003ff could not be reserved
[ 0.454810] system 00:04: driver attached
[ 0.454816] system 00:06: ioport range 0x680-0x69f has been reserved
[ 0.454819] system 00:06: ioport range 0x800-0x80f has been reserved
[ 0.454822] system 00:06: ioport range 0x1000-0x107f has been reserved
[ 0.454825] system 00:06: ioport range 0x1180-0x11bf has been reserved
[ 0.454828] system 00:06: ioport range 0xfe00-0xfe00 has been reserved
[ 0.454831] system 00:06: ioport range 0xff00-0xff7f has been reserved
[ 0.454833] system 00:06: driver attached
[ 0.455950] PCI: Bridge: 0000:00:1c.0
[ 0.455950] IO window: 2000-2fff
[ 0.455950] MEM window: 0xc4000000-0xc7ffffff
[ 0.455950] PREFETCH window: 0x00000000cc000000-0x00000000cdffffff
[ 0.455950] PCI: Bridge: 0000:00:1c.1
[ 0.455950] IO window: 3000-3fff
[ 0.455950] MEM window: 0xf0000000-0xf3ffffff
[ 0.455950] PREFETCH window: 0x00000000fa000000-0x00000000fbffffff
[ 0.455950] PCI: Bridge: 0000:00:1c.3
[ 0.455950] IO window: 4000-4fff
[ 0.455950] MEM window: 0xf4000000-0xf7ffffff
[ 0.455950] PREFETCH window: 0x00000000fc000000-0x00000000fdffffff
[ 0.455950] PCI: Bridge: 0000:00:1c.4
[ 0.455950] IO window: 5000-5fff
[ 0.455950] MEM window: 0xc2000000-0xc20fffff
[ 0.455950] PREFETCH window: 0x00000000f8600000-0x00000000f86fffff
[ 0.455950] PCI: Bridge: 0000:00:1e.0
[ 0.455950] IO window: disabled.
[ 0.455950] MEM window: 0xf8200000-0xf82fffff
[ 0.455950] PREFETCH window: disabled.
[ 0.455950] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 0.455950] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.455950] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
[ 0.455950] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.455950] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
[ 0.455950] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 0.455950] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17
[ 0.455950] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 0.455950] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.455950] NET: Registered protocol family 2
[ 0.491246] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.493279] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 0.497290] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.497290] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.497290] TCP reno registered
[ 0.506711] NET: Registered protocol family 1
[ 0.506826] checking if image is initramfs...<7>Switched to high resolution mode on CPU 1
[ 0.509283] Switched to high resolution mode on CPU 0
[ 0.833562] it is
[ 1.177563] Freeing initrd memory: 7588k freed
[ 1.181564] Simple Boot Flag at 0x36 set to 0x1
[ 1.184925] audit: initializing netlink socket (disabled)
[ 1.184925] type=2000 audit(1225794110.173:1): initialized
[ 1.184925] VFS: Disk quotas dquot_6.5.1
[ 1.184960] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.184995] msgmni has been set to 7922
[ 1.185053] io scheduler noop registered
[ 1.185055] io scheduler anticipatory registered
[ 1.185057] io scheduler deadline registered
[ 1.185070] io scheduler cfq registered (default)
[ 1.185083] pci 0000:00:02.0: Boot video device
[ 1.187347] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 1.187397] assign_interrupt_mode Found MSI capability
[ 1.187450] Allocate Port Service[0000:00:1c.0:pcie00]
[ 1.188927] Allocate Port Service[0000:00:1c.0:pcie02]
[ 1.188927] Allocate Port Service[0000:00:1c.0:pcie03]
[ 1.188927] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 1.188927] assign_interrupt_mode Found MSI capability
[ 1.188927] Allocate Port Service[0000:00:1c.1:pcie00]
[ 1.188927] Allocate Port Service[0000:00:1c.1:pcie02]
[ 1.188927] Allocate Port Service[0000:00:1c.1:pcie03]
[ 1.188927] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 1.188927] assign_interrupt_mode Found MSI capability
[ 1.188927] Allocate Port Service[0000:00:1c.3:pcie00]
[ 1.188927] Allocate Port Service[0000:00:1c.3:pcie02]
[ 1.188927] Allocate Port Service[0000:00:1c.3:pcie03]
[ 1.188927] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 1.188927] assign_interrupt_mode Found MSI capability
[ 1.188927] Allocate Port Service[0000:00:1c.4:pcie00]
[ 1.188927] Allocate Port Service[0000:00:1c.4:pcie02]
[ 1.188927] Allocate Port Service[0000:00:1c.4:pcie03]
[ 1.189629] hpet_resources: 0xfed00000 is busy
[ 1.189689] Linux agpgart interface v0.103
[ 1.189692] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.189992] pnp: the driver 'serial' has been registered
[ 1.191624] brd: module loaded
[ 1.191710] pnp: the driver 'i8042 kbd' has been registered
[ 1.191725] i8042 kbd 00:08: driver attached
[ 1.191760] pnp: the driver 'i8042 aux' has been registered
[ 1.191778] i8042 aux 00:09: driver attached
[ 1.191812] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.233364] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.233370] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.236983] mice: PS/2 mouse device common for all mice
[ 1.236983] cpuidle: using governor ladder
[ 1.236983] cpuidle: using governor menu
[ 1.239129] TCP bic registered
[ 1.239129] NET: Registered protocol family 17
[ 1.239129] registered taskstats version 1
[ 1.239129] Freeing unused kernel memory: 340k freed
[ 1.239129] Write protecting the kernel read-only data: 3376k
[ 1.274139] input: AT Translated Set 2 keyboard as /class/input/input0
[ 1.323134] ACPI: SSDT BF6D75EB, 0238 (r1 PmRef Cpu0Ist 3000 INTL 20061109)
[ 1.323134] ACPI: SSDT BF6D6F7C, 05EA (r1 PmRef Cpu0Cst 3001 INTL 20061109)
[ 1.327133] Monitor-Mwait will be used to enter C-1 state
[ 1.327133] Monitor-Mwait will be used to enter C-2 state
[ 1.327133] Monitor-Mwait will be used to enter C-3 state
[ 1.327133] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 1.331132] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.331132] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 1.331132] ACPI: SSDT BF6D7823, 00C8 (r1 PmRef Cpu1Ist 3000 INTL 20061109)
[ 1.331132] ACPI: SSDT BF6D7566, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20061109)
[ 1.334145] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 1.334145] ACPI: ACPI0007:01 is registered as cooling_device1
[ 1.334145] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 1.334145] Marking TSC unstable due to TSC halts in idle
[ 1.598158] USB Universal Host Controller Interface driver v3.0
[ 1.598201] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.598212] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 1.598216] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.598372] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 1.598412] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001820
[ 1.598509] usb usb1: configuration #1 chosen from 1 choice
[ 1.598539] hub 1-0:1.0: USB hub found
[ 1.598547] hub 1-0:1.0: 2 ports detected
[ 1.669817] No dock devices found.
[ 1.674481] SCSI subsystem initialized
[ 1.705819] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
[ 1.705819] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 1.705819] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.705819] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 1.705819] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001840
[ 1.705819] usb usb2: configuration #1 chosen from 1 choice
[ 1.705819] hub 2-0:1.0: USB hub found
[ 1.705819] hub 2-0:1.0: 2 ports detected
[ 1.761054] libata version 3.00 loaded.
[ 1.761054] sdhci: Secure Digital Host Controller Interface driver
[ 1.761054] sdhci: Copyright(c) Pierre Ossman
[ 1.808072] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
[ 1.808072] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 1.808072] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 1.808072] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3
[ 1.812219] ehci_hcd 0000:00:1a.7: debug port 1
[ 1.812219] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 1.812219] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf8504800
[ 1.827827] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.827918] usb usb3: configuration #1 chosen from 1 choice
[ 1.827954] hub 3-0:1.0: USB hub found
[ 1.827962] hub 3-0:1.0: 4 ports detected
[ 1.931807] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 1.931807] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 1.931807] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.931807] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 1.931807] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001860
[ 1.931807] usb usb4: configuration #1 chosen from 1 choice
[ 1.931807] hub 4-0:1.0: USB hub found
[ 1.931807] hub 4-0:1.0: 2 ports detected
[ 2.026360] Clocksource tsc unstable (delta = -235519534 ns)
[ 2.037372] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 2.037372] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 2.037372] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.037372] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
[ 2.037372] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001880
[ 2.037372] usb usb5: configuration #1 chosen from 1 choice
[ 2.037372] hub 5-0:1.0: USB hub found
[ 2.037372] hub 5-0:1.0: 2 ports detected
[ 2.141131] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 2.141131] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 2.141131] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.141131] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
[ 2.141131] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018a0
[ 2.141131] usb usb6: configuration #1 chosen from 1 choice
[ 2.141131] hub 6-0:1.0: USB hub found
[ 2.141131] hub 6-0:1.0: 2 ports detected
[ 2.243959] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 2.243959] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 2.243959] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.243959] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
[ 2.247781] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.247781] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 2.247781] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf8504c00
[ 2.263903] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.263985] usb usb7: configuration #1 chosen from 1 choice
[ 2.264024] hub 7-0:1.0: USB hub found
[ 2.264031] hub 7-0:1.0: 6 ports detected
[ 2.370903] r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
[ 2.370903] ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 2.370903] PCI: Setting latency timer of device 0000:07:00.0 to 64
[ 2.370903] eth0: RTL8168c/8111c at 0xffffc2000065c000, 00:21:70:a7:fd:30, XID 3c4000c0 IRQ 379
[ 2.372530] ahci 0000:00:1f.2: version 3.0
[ 2.372557] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 18 (level, low) -> IRQ 18
[ 2.854088] usb 7-6: new high speed USB device using ehci_hcd and address 3
[ 3.027530] usb 7-6: configuration #1 chosen from 1 choice
[ 3.270823] usb 4-2: new full speed USB device using uhci_hcd and address 2
[ 3.378371] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
[ 3.378377] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part
[ 3.378384] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 3.380433] scsi0 : ahci
[ 3.380433] scsi1 : ahci
[ 3.380433] scsi2 : ahci
[ 3.380433] ata1: SATA max UDMA/133 abar m2048@0xf8504000 port 0xf8504100 irq 378
[ 3.380433] ata2: SATA max UDMA/133 abar m2048@0xf8504000 port 0xf8504180 irq 378
[ 3.380433] ata3: SATA max UDMA/133 abar m2048@0xf8504000 port 0xf8504200 irq 378
[ 3.453005] usb 4-2: configuration #1 chosen from 1 choice
[ 3.700617] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.702260] ata1.00: _GTF unexpected object type 0x1
[ 3.731941] ata1.00: ATA-8: ST9160310AS, DE04, max UDMA/133
[ 3.731941] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 3.747312] ata1.00: _GTF unexpected object type 0x1
[ 3.776914] ata1.00: configured for UDMA/133
[ 4.096487] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.418041] ata3: SATA link down (SStatus 0 SControl 300)
[ 4.418013] scsi 0:0:0:0: Direct-Access ATA ST9160310AS DE04 PQ: 0 ANSI: 5
[ 4.418013] sdhci: SDHCI controller found at 0000:08:05.2 [1217:7120] (rev 2)
[ 4.418013] ACPI: PCI Interrupt 0000:08:05.2[A] -> GSI 22 (level, low) -> IRQ 22
[ 4.418013] mmc0: Unknown controller version (2). You may experience problems.
[ 4.418013] mmc0: SDHCI at 0xf8202800 irq 22 DMA
[ 4.428641] Uniform Multi-Platform E-IDE driver
[ 4.428646] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 4.428785] ICH8M: IDE controller (0x8086:0x2850 rev 0x03) at PCI slot 0000:00:1f.1
[ 4.428785] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[ 4.428785] ICH8M: not 100% native mode: will probe irqs later
[ 4.428785] ide0: BM-DMA at 0x1810-0x1817
[ 4.428785] ide1: BM-DMA at 0x1818-0x181f
[ 4.428785] Probing IDE interface ide0...
[ 4.453097] Driver 'sd' needs updating - please use bus_type methods
[ 4.453097] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 4.453097] sd 0:0:0:0: [sda] Write Protect is off
[ 4.453097] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.453097] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.453097] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 4.453097] sd 0:0:0:0: [sda] Write Protect is off
[ 4.453097] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.453097] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.453097] sda: sda1 sda2 sda3
[ 4.463890] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.164297] hda: Optiarc DVD+/-RW AD-7640A, ATAPI CD/DVD-ROM drive
[ 5.836118] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 5.836498] hda: UDMA/33 mode selected
[ 5.840923] Probing IDE interface ide1...
[ 6.405004] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 6.407726] ide1 at 0x170-0x177,0x376 on irq 15
[ 6.427362] hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
[ 6.427362] Uniform CD-ROM driver Revision: 3.20
[ 6.514257] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@xxxxxxxxxx
[ 6.597852] PM: Starting manual resume from disk
[ 6.710189] kjournald starting. Commit interval 5 seconds
[ 6.710203] EXT3-fs: mounted filesystem with writeback data mode.
[ 8.559252] udevd version 125 started
[ 8.991246] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 9.169086] input: Power Button (FF) as /class/input/input1
[ 9.219004] ACPI: Power Button (FF) [PWRF]
[ 9.219076] input: Lid Switch as /class/input/input2
[ 9.252261] ACPI: Lid Switch [LID0]
[ 9.252321] input: Power Button (CM) as /class/input/input3
[ 9.256122] agpgart: Detected an Intel 965GM Chipset.
[ 9.256692] agpgart: Detected 7676K stolen memory.
[ 9.269209] agpgart: AGP aperture is 256M @ 0xd0000000
[ 9.318999] ACPI: Power Button (CM) [PWRB]
[ 9.321075] input: Sleep Button (CM) as /class/input/input4
[ 9.384095] ACPI: Sleep Button (CM) [SLPB]
[ 9.385011] ACPI: WMI: Mapper loaded
[ 9.391603] ACPI: AC Adapter [ACAD] (on-line)
[ 9.531606] ACPI: device:05 is registered as cooling_device2
[ 9.531606] input: Video Bus as /class/input/input5
[ 9.580294] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 9.592061] ACPI: device:0a is registered as cooling_device3
[ 9.592419] input: Video Bus as /class/input/input6
[ 9.612220] ieee80211_crypt: registered algorithm 'NULL'
[ 9.649350] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 10.002911] ACPI: Battery Slot [BAT1] (battery present)
[ 10.069690] wl: module license 'unspecified' taints kernel.
[ 10.074913] ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 10.074913] PCI: Setting latency timer of device 0000:06:00.0 to 64
[ 10.145119] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 10.145119] iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
[ 10.145119] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 10.180255] pnp: the driver 'rtc_cmos' has been registered
[ 10.180317] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 10.180343] rtc0: alarms up to one month, y3k
[ 10.180345] rtc_cmos 00:07: driver attached
[ 10.194514] ieee80211_crypt: registered algorithm 'TKIP'
[ 10.194514] wlan0: Broadcom BCM4315 802.11 Wireless Controller 5.10.27.6
[ 10.266551] Linux video capture interface: v2.00
[ 10.286536] input: PC Speaker as /class/input/input7
[ 10.375098] ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
[ 10.397199] uvcvideo: Found UVC 1.00 device Integrated Webcam (0c45:63e0)
[ 10.415369] input: Integrated Webcam as /class/input/input8
[ 10.448428] usbcore: registered new interface driver uvcvideo
[ 10.448433] USB Video Class driver (v0.1.0)
[ 10.457296] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 10.457296] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 10.487781] hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
[ 11.063235] input: PS/2 Mouse as /class/input/input9
[ 11.142266] input: AlpsPS/2 ALPS GlidePoint as /class/input/input10
[ 12.778033] EXT3 FS on dm-0, internal journal
[ 13.325076] loop: module loaded
[ 13.680289] Broadcom 43xx driver loaded [ Features: PLR, Firmware-ID: FW13 ]
[ 13.717388] Ethernet Channel Bonding Driver: v3.2.5 (March 21, 2008)
[ 13.717388] bonding: MII link monitoring set to 1500 ms
[ 15.101058] fuse init (API version 7.9)
[ 15.226078] kjournald starting. Commit interval 5 seconds
[ 15.226876] EXT3 FS on dm-1, internal journal
[ 15.226876] EXT3-fs: mounted filesystem with writeback data mode.
[ 15.284065] kjournald starting. Commit interval 5 seconds
[ 15.292828] EXT3 FS on sda2, internal journal
[ 15.292828] EXT3-fs: mounted filesystem with ordered data mode.
[ 15.390085] Adding 6291448k swap on /dev/mapper/gamow-swap. Priority:-1 extents:1 across:6291448k
[ 17.094378] bonding: bond0: Warning: failed to get speed and duplex from wlan0, assumed to be 100Mb/sec and Full.
[ 17.094378] bonding: bond0: enslaving wlan0 as a backup interface with an up link.
[ 17.989324] NET: Registered protocol family 10
[ 17.989685] lo: Disabled Privacy Extensions
[ 17.992056] ADDRCONF(NETDEV_UP): bond0: link is not ready
[ 18.209717] r8169: eth0: link up
[ 18.210290] r8169: eth0: link up
[ 18.268847] r8169: eth0: link up
[ 18.269506] bonding: bond0: enslaving eth0 as a backup interface with an up link.
[ 21.521015] bonding: bond0: link status definitely up for interface wlan0.
[ 21.521021] bonding: bond0: link status definitely up for interface eth0.
[ 21.521033] bonding: bond0: making interface eth0 the new active one.
[ 21.521058] bonding: bond0: first active interface up!
[ 21.521751] ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
[ 22.040786] RPC: Registered udp transport module.
[ 22.040786] RPC: Registered tcp transport module.
[ 22.282259] Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
[ 24.171512] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 24.284604] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 27.609165] pnp: the driver 'parport_pc' has been registered
[ 27.614107] lp: driver loaded but no devices found
[ 27.670753] ppdev: user-space parallel port driver
[ 32.189872] bond0: no IPv6 routers present
[ 57.283130] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 57.283149] NFSD: unable to find recovery directory /var/lib/nfs/v4recovery
[ 57.283152] NFSD: starting 90-second grace period
[ 62.651315] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
[ 68.040853] CPU0 attaching NULL sched-domain.
[ 68.040853] CPU1 attaching NULL sched-domain.
[ 68.067474] CPU0 attaching sched-domain:
[ 68.067588] domain 0: span 0-1
[ 68.067596] groups: 0 1
[ 68.067605] domain 1: span 0-1
[ 68.067609] groups: 0-1
[ 68.067618] CPU1 attaching sched-domain:
[ 68.067758] domain 0: span 0-1
[ 68.067768] groups: 1 0
[ 68.067775] domain 1: span 0-1
[ 68.067779] groups: 0-1
[ 71.739745] ACPI: EC: missing confirmations, switch off interrupt mode.
[ 72.259596] ACPI Exception (evregion-0420): AE_TIME, Returned by Handler for [EmbeddedControl] [20080321]
[ 72.259612] ACPI Error (psparse-0530): Method parse/execution failed [\_SB_.PCI0.GFX0.DD03._BQC] (Node ffff81013fa6ea90), AE_TIME
[ 74.111540] [drm] Initialized drm 1.1.0 20060810
[ 74.163638] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 74.163649] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 74.163961] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 75.189420] mtrr: type mismatch for d0000000,10000000 old: write-back new: write-combining
[ 1054.475893] r8169: eth0: link down
[ 1054.971140] bonding: bond0: link status down for idle interface eth0, disabling it in 1500 ms.
[ 1056.472248] bonding: bond0: link status definitely down for interface eth0, disabling it
[ 1056.472272] bonding: bond0: making interface wlan0 the new active one.
[ 1060.210232] r8169: eth0: link up
[ 1061.696625] bonding: bond0: link status up for interface eth0, enabling it in 3000 ms.
[ 1064.696483] bonding: bond0: link status definitely up for interface eth0.
[ 1064.696507] bonding: bond0: making interface eth0 the new active one.
[ 1067.767643] bond0: no IPv6 routers present
[ 1114.153142] CE: hpet increasing min_delta_ns to 15000 nsec