Re: mptsas, msi and the dl585 g2

From: dann frazier
Date: Thu Jul 09 2009 - 15:00:40 EST


On Sat, Jul 04, 2009 at 12:30:36PM -0700, Yinghai Lu wrote:
> dann frazier wrote:
> > On Tue, Jun 30, 2009 at 11:35:45AM -0700, Yinghai Lu wrote:
> >> dann frazier wrote:
> >>> hey,
> >>> I'm finding problems when booting a dl585g2 w/ an LSISAS1068
> >>> controller. In brief, this system system stopped booting once MSI
> >>> became disabled by default in mptbase. Passing the parameter
> >>> 'mpt_msi_enable_sas=1' to mptbase allows it to work again (tested w/
> >>> 2.6.30).
> >>>
> >>> The symptom is that the system starts up, and we see the following:
> >>>
> >>> ======== SNIP =========
> >>> [ 6.941489] hub 3-2:1.0: USB hub found
> >>> [ 6.943705] hub 3-2:1.0: 7 ports detected
> >>> [ 6.992639] Copyright (c) 1999-2008 LSI Corporation
> >>> [ 7.014262] Fusion MPT SAS Host driver 3.04.07
> >>> [ 7.021685] mptsas 0000:42:01.0: PCI INT A -> GSI 24 (level, low) -> IRQ 24
> >>> [ 7.026597] usb 1-6.3: new full speed USB device using ehci_hcd and address 3
> >>> [ 7.071143] mptbase: ioc0: Initiating bringup
> >>> [ 7.102198] usb 1-6.3: New USB device found, idVendor=0e34, idProduct=0204
> >>> [ 7.119107] usb 1-6.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
> >>> [ 7.128171] usb 1-6.3: Product: iPort/USB I2C Host Adapter
> >>> [ 7.160994] usb 1-6.3: Manufacturer: Silicon Labs
> >>> [ 7.171468] usb 1-6.3: SerialNumber: 0001248
> >>> [ 7.174931] usb 1-6.3: configuration #1 chosen from 1 choice
> >>> [ 7.360010] ioc0: LSISAS1068 B0: Capabilities={Initiator}
> >>> [ 40.581020] mptbase: ioc0: Initiating recovery
> >>> [ 71.190560] Clocksource tsc unstable (delta = 4398041105588 ns)
> >>> [ 81.190160] mptbase: ioc0: Initiating recovery
> >>> ======== SNIP =========
> >>>
> >>> These "Initiating recovery" messages are printed periodically, and the
> >>> system never recovers.
> >> Dann, that could be : ioapic routing in ACPI DSDT is not right somehow.
> >>
> >> please try to move the card to other slot to get some luck.
> >> or pci=routeirq could help too sometimes.
> >
> > For the record, I tried moving the card to the other PCI-X slot and
> > the pci=routeirq boot param, but neither helped.
> >
>
> so 2.6.22.1 works on that system with pci=nomsi?
>
> maybe your BIOS is too new, you may try the old BIOS.
>
> updating BIOS is not always a option to deployed systems. maybe sustaining team could break sth.

Back with more info.

Both of the original bisects I did with cciss and mptsas appeared to
land on commits that just masked the issue. e.g., a cciss hang caused
by a bug w/ no logical drives, and mptsas switching toggling the MSI
default.

I tried to avoid these issues by doing another bisect w/ storage
attached to the cciss controller, and landed on this commit:

--------------------------------------------------------------------
commit 8d539108560ec121d59eee05160236488266221c
Author: Linus Torvalds <torvalds@xxxxxxxxxxxxxxxxxxxx>
Date: Thu May 8 18:41:48 2008 -0700

Revert "PCI: remove default PCI expansion ROM memory allocation"

This reverts commit 9f8daccaa05c14e5643bdd4faf5aed9cc8e6f11e, which
was reported to break X startup (xf86-video-ati-6.8.0).
--------------------------------------------------------------------

>From that, I found that pci=norom avoids the problem. But, again, this
is just a masking commit - things used to work before 9f8dacc was
there.

I did another bisect, this time keeping the norom patches out
entirely. This landed on:

--------------------------------------------------------------------
commit 30a18d6c3f1e774de656ebd8ff219d53e2ba4029
Author: Yinghai Lu <Yinghai.Lu@xxxxxxx>
Date: Tue Feb 19 03:21:20 2008 -0800

x86: multi pci root bus with different io resource range, on
64-bit
--------------------------------------------------------------------

This appears to be the commit that actually introduced the issue.
I've attached dmesg w/ PCI DEBUG enabled from both sides of this
changeset, as well as a diff w/o printk timestamps.

Also note that #ifdef'ing out x86_pci_root_bus_res_quirks() in
amd_bus.c seems to avoid the problem as well.

--
dann frazier

[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.25 (dannf@dl585g2) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #68 SMP Thu Jul 9 12:25:31 MDT 2009
[ 0.000000] Command line: root=/dev/disk/by-id/scsi-35000c50000d5ca0f-part1 ro console=tty1 console=ttyS1,115200
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e400 (usable)
[ 0.000000] BIOS-e820: 000000000009e400 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fd4e000 (usable)
[ 0.000000] BIOS-e820: 000000007fd4e000 - 000000007fd56000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007fd56000 - 000000007fd57000 (usable)
[ 0.000000] BIOS-e820: 000000007fd57000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fed00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffc00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 000000047ffff000 (usable)
[ 0.000000] Entering add_active_range(0, 0, 158) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 523598) 1 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 523606, 523607) 2 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 1048576, 4718591) 3 entries of 3200 used
[ 0.000000] max_pfn_mapped = 4718591
[ 0.000000] x86: PAT support disabled.
[ 0.000000] init_memory_mapping
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI: RSDP 000F4F00, 0024 (r2 HP )
[ 0.000000] ACPI: XSDT 7FD4ED80, 0074 (r1 HP ProLiant 2 Ò 162E)
[ 0.000000] ACPI: FACP 7FD4EE00, 00F4 (r3 HP A07 2 Ò 162E)
[ 0.000000] ACPI: DSDT 7FD4EF00, 4A59 (r1 HP DSDT 1 INTL 20030228)
[ 0.000000] ACPI: FACS 7FD4E100, 0040
[ 0.000000] ACPI: SPCR 7FD4E140, 0050 (r1 HP SPCRRBSU 1 Ò 162E)
[ 0.000000] ACPI: HPET 7FD4E1C0, 0038 (r1 HP ProLiant 2 Ò 162E)
[ 0.000000] ACPI: SPMI 7FD4E200, 0040 (r5 HP ProLiant 1 Ò 162E)
[ 0.000000] ACPI: ERST 7FD4E240, 01D0 (r1 HP ProLiant 1 Ò 162E)
[ 0.000000] ACPI: APIC 7FD4E440, 00C6 (r1 HP ProLiant 2 0)
[ 0.000000] ACPI: SRAT 7FD4E600, 01A0 (r1 AMD FAM_F_10 2 AMD 1)
[ 0.000000] ACPI: FFFF 7FD4EA00, 0176 (r1 HP ProLiant 1 Ò 162E)
[ 0.000000] ACPI: BERT 7FD4EB80, 0030 (r1 HP ProLiant 1 Ò 162E)
[ 0.000000] ACPI: HEST 7FD4EBC0, 0170 (r1 HP ProLiant 1 Ò 162E)
[ 0.000000] SRAT: PXM 0 -> APIC 0 -> Node 0
[ 0.000000] SRAT: PXM 0 -> APIC 1 -> Node 0
[ 0.000000] SRAT: PXM 1 -> APIC 2 -> Node 1
[ 0.000000] SRAT: PXM 1 -> APIC 3 -> Node 1
[ 0.000000] SRAT: PXM 2 -> APIC 4 -> Node 2
[ 0.000000] SRAT: PXM 2 -> APIC 5 -> Node 2
[ 0.000000] SRAT: PXM 3 -> APIC 6 -> Node 3
[ 0.000000] SRAT: PXM 3 -> APIC 7 -> Node 3
[ 0.000000] SRAT: Node 0 PXM 0 0-a0000
[ 0.000000] Entering add_active_range(0, 0, 158) 0 entries of 3200 used
[ 0.000000] SRAT: Node 0 PXM 0 100000-80000000
[ 0.000000] Entering add_active_range(0, 256, 523598) 1 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 523606, 523607) 2 entries of 3200 used
[ 0.000000] SRAT: Node 0 PXM 0 100000000-180000000
[ 0.000000] Entering add_active_range(0, 1048576, 1572864) 3 entries of 3200 used
[ 0.000000] SRAT: Node 1 PXM 1 180000000-280000000
[ 0.000000] Entering add_active_range(1, 1572864, 2621440) 4 entries of 3200 used
[ 0.000000] SRAT: Node 2 PXM 2 280000000-380000000
[ 0.000000] Entering add_active_range(2, 2621440, 3670016) 5 entries of 3200 used
[ 0.000000] SRAT: Node 3 PXM 3 380000000-480000000
[ 0.000000] Entering add_active_range(3, 3670016, 4718591) 6 entries of 3200 used
[ 0.000000] NUMA: Allocated memnodemap from 1a000 - 23080
[ 0.000000] NUMA: Using 20 for the hash shift.
[ 0.000000] Bootmem setup node 0 0000000000000000-0000000180000000
[ 0.000000] NODE_DATA [0000000000023080 - 000000000002b07f]
[ 0.000000] bootmap [000000000002c000 - 000000000005bfff] pages 30
[ 0.000000] early res: 0 [0-fff] BIOS data page
[ 0.000000] early res: 1 [6000-7fff] TRAMPOLINE
[ 0.000000] early res: 2 [200000-a88afb] TEXT DATA BSS
[ 0.000000] early res: 3 [37d54000-37fef2b8] RAMDISK
[ 0.000000] early res: 4 [9e400-fffff] BIOS reserved
[ 0.000000] early res: 5 [8000-19fff] PGTABLE
[ 0.000000] early res: 6 [1a000-2307f] MEMNODEMAP
[ 0.000000] Bootmem setup node 1 0000000180000000-0000000280000000
[ 0.000000] NODE_DATA [0000000180000000 - 0000000180007fff]
[ 0.000000] bootmap [0000000180008000 - 0000000180027fff] pages 20
[ 0.000000] Bootmem setup node 2 0000000280000000-0000000380000000
[ 0.000000] NODE_DATA [0000000280000000 - 0000000280007fff]
[ 0.000000] bootmap [0000000280008000 - 0000000280027fff] pages 20
[ 0.000000] Bootmem setup node 3 0000000380000000-000000047ffff000
[ 0.000000] NODE_DATA [0000000380000000 - 0000000380007fff]
[ 0.000000] bootmap [0000000380008000 - 0000000380027fff] pages 20
[ 0.000000] [ffffe20000000000-ffffe200049fffff] PMD -> [ffff810001200000-ffff810003ffffff] on node 0
[ 0.000000] [ffffe20004a00000-ffffe200053fffff] PMD -> [ffff81000c000000-ffff81000c9fffff] on node 0
[ 0.000000] [ffffe20005400000-ffffe20008bfffff] PMD -> [ffff810180200000-ffff8101839fffff] on node 1
[ 0.000000] [ffffe20008c00000-ffffe2000c3fffff] PMD -> [ffff810280200000-ffff8102839fffff] on node 2
[ 0.000000] [ffffe2000c400000-ffffe2000fbfffff] PMD -> [ffff810380200000-ffff8103839fffff] on node 3
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 4718591
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[7] active PFN ranges
[ 0.000000] 0: 0 -> 158
[ 0.000000] 0: 256 -> 523598
[ 0.000000] 0: 523606 -> 523607
[ 0.000000] 0: 1048576 -> 1572864
[ 0.000000] 1: 1572864 -> 2621440
[ 0.000000] 2: 2621440 -> 3670016
[ 0.000000] 3: 3670016 -> 4718591
[ 0.000000] On node 0 totalpages: 1047789
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 2313 pages reserved
[ 0.000000] DMA zone: 1629 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 505223 pages, LIFO batch:31
[ 0.000000] Normal zone: 7168 pages used for memmap
[ 0.000000] Normal zone: 517120 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] On node 1 totalpages: 1048576
[ 0.000000] DMA zone: 0 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages used for memmap
[ 0.000000] Normal zone: 14336 pages used for memmap
[ 0.000000] Normal zone: 1034240 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] On node 2 totalpages: 1048576
[ 0.000000] DMA zone: 0 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages used for memmap
[ 0.000000] Normal zone: 14336 pages used for memmap
[ 0.000000] Normal zone: 1034240 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] On node 3 totalpages: 1048575
[ 0.000000] DMA zone: 0 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages used for memmap
[ 0.000000] Normal zone: 14335 pages used for memmap
[ 0.000000] Normal zone: 1034240 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] ACPI: PM-Timer IO Port: 0x908
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xd9cf0000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 0, address 0xd9cf0000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x09] address[0xd9fd0000] gsi_base[24])
[ 0.000000] IOAPIC[1]: apic_id 9, version 0, address 0xd9fd0000, GSI 24-30
[ 0.000000] ACPI: IOAPIC (id[0x0a] address[0xd9fe0000] gsi_base[31])
[ 0.000000] IOAPIC[2]: apic_id 10, version 0, address 0xd9fe0000, GSI 31-37
[ 0.000000] ACPI: IOAPIC (id[0x0b] address[0xd9ff0000] gsi_base[38])
[ 0.000000] IOAPIC[3]: apic_id 11, version 0, address 0xd9ff0000, GSI 38-61
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: NMI_SRC (dfl dfl global_irq 28)
[ 0.000000] ACPI: NMI_SRC (dfl dfl global_irq 35)
[ 0.000000] Setting APIC routing to flat
[ 0.000000] ACPI: HPET id: 0x10228201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007fd4e000 - 000000007fd56000
[ 0.000000] PM: Registered nosave memory: 000000007fd57000 - 0000000080000000
[ 0.000000] PM: Registered nosave memory: 0000000080000000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
[ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fed00000
[ 0.000000] PM: Registered nosave memory: 00000000fed00000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee10000
[ 0.000000] PM: Registered nosave memory: 00000000fee10000 - 00000000ffc00000
[ 0.000000] PM: Registered nosave memory: 00000000ffc00000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
[ 0.000000] SMP: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 44480 bytes of per cpu data
[ 0.000000] NR_CPUS: 64, nr_cpu_ids: 8
[ 0.000000] Built 4 zonelists in Zone order, mobility grouping on. Total pages: 4126692
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: root=/dev/disk/by-id/scsi-35000c50000d5ca0f-part1 ro console=tty1 console=ttyS1,115200
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] TSC calibrated against PM_TIMER
[ 0.000001] Marking TSC unstable due to TSCs unsynchronized
[ 0.000003] time.c: Detected 2612.039 MHz processor.
[ 0.000011] spurious 8259A interrupt: IRQ7.
[ 0.000999] Console: colour VGA+ 80x25
[ 0.000999] console [tty1] enabled
[ 0.000999] console [ttyS1] enabled
[ 0.000999] Checking aperture...
[ 0.000999] Node 0: aperture @ 4000000 size 32 MB
[ 0.000999] Aperture pointing to e820 RAM. Ignoring.
[ 0.000999] No AGP bridge found
[ 0.000999] Your BIOS doesn't leave a aperture memory hole
[ 0.000999] Please enable the IOMMU option in the BIOS setup
[ 0.000999] This costs you 64 MB of RAM
[ 0.000999] Mapping aperture over 65536 KB of RAM @ 4000000
[ 0.000999] PM: Registered nosave memory: 0000000004000000 - 0000000008000000
[ 0.000999] Memory: 16466524k/18874364k available (4336k kernel code, 307540k reserved, 2815k data, 404k init)
[ 0.000999] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.000999] SLUB: Genslabs=13, HWalign=64, Order=0-1, MinObjects=4, CPUs=8, Nodes=4
[ 0.000999] hpet clockevent registered
[ 0.059992] Calibrating delay using timer specific routine.. 5226.25 BogoMIPS (lpj=2613125)
[ 0.061048] Security Framework initialized
[ 0.061995] SELinux: Initializing.
[ 0.063002] SELinux: Starting in permissive mode
[ 0.063011] selinux_register_security: Registering secondary module capability
[ 0.063991] Capability LSM initialized as secondary
[ 0.066692] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.080601] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.087485] Mount-cache hash table entries: 256
[ 0.088147] Initializing cgroup subsys ns
[ 0.088519] Initializing cgroup subsys cpuacct
[ 0.089010] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.089988] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.090988] CPU 0/0 -> Node 0
[ 0.091995] CPU: Physical Processor ID: 0
[ 0.092987] CPU: Processor Core ID: 0
[ 0.094001] ACPI: Core revision 20070126
[ 0.114009] CPU0: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.116983] Using local APIC timer interrupts.
[ 0.118982] APIC timer calibration result 12557872
[ 0.118984] Detected 12.557 MHz APIC timer.
[ 0.120112] Booting processor 1/2 ip 6000
[ 0.120112] Initializing CPU#1
[ 0.120112] Calibrating delay using timer specific routine.. 5223.88 BogoMIPS (lpj=2611941)
[ 0.120112] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.120112] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.120112] CPU 1/2 -> Node 1
[ 0.120112] CPU: Physical Processor ID: 1
[ 0.120112] CPU: Processor Core ID: 0
[ 0.120112] x86: PAT support disabled.
[ 0.192341] CPU1: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.195052] Booting processor 2/4 ip 6000
[ 0.195052] Initializing CPU#2
[ 0.195052] Calibrating delay using timer specific routine.. 5223.84 BogoMIPS (lpj=2611922)
[ 0.195052] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.195052] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.195052] CPU 2/4 -> Node 2
[ 0.195052] CPU: Physical Processor ID: 2
[ 0.195052] CPU: Processor Core ID: 0
[ 0.195052] x86: PAT support disabled.
[ 0.267306] CPU2: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.270039] Booting processor 3/6 ip 6000
[ 0.270039] Initializing CPU#3
[ 0.270039] Calibrating delay using timer specific routine.. 5223.86 BogoMIPS (lpj=2611930)
[ 0.270039] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.270039] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.270039] CPU 3/6 -> Node 3
[ 0.270039] CPU: Physical Processor ID: 3
[ 0.270039] CPU: Processor Core ID: 0
[ 0.270039] x86: PAT support disabled.
[ 0.342371] CPU3: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.345016] Booting processor 4/1 ip 6000
[ 0.345016] Initializing CPU#4
[ 0.345016] Calibrating delay using timer specific routine.. 5223.82 BogoMIPS (lpj=2611910)
[ 0.345016] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.345016] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.345016] CPU 4/1 -> Node 0
[ 0.345016] CPU: Physical Processor ID: 0
[ 0.345016] CPU: Processor Core ID: 1
[ 0.345016] x86: PAT support disabled.
[ 0.417217] CPU4: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.420014] Booting processor 5/3 ip 6000
[ 0.420014] Initializing CPU#5
[ 0.420014] Calibrating delay using timer specific routine.. 5223.85 BogoMIPS (lpj=2611926)
[ 0.420014] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.420014] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.420014] CPU 5/3 -> Node 1
[ 0.420014] CPU: Physical Processor ID: 1
[ 0.420014] CPU: Processor Core ID: 1
[ 0.420014] x86: PAT support disabled.
[ 0.492337] CPU5: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.494997] Booting processor 6/5 ip 6000
[ 0.494997] Initializing CPU#6
[ 0.494997] Calibrating delay using timer specific routine.. 5223.87 BogoMIPS (lpj=2611937)
[ 0.494997] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.494997] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.494997] CPU 6/5 -> Node 2
[ 0.494997] CPU: Physical Processor ID: 2
[ 0.494997] CPU: Processor Core ID: 1
[ 0.494997] x86: PAT support disabled.
[ 0.567297] CPU6: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.569990] Booting processor 7/7 ip 6000
[ 0.569990] Initializing CPU#7
[ 0.569990] Calibrating delay using timer specific routine.. 5223.84 BogoMIPS (lpj=2611921)
[ 0.569990] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.569990] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.569990] CPU 7/7 -> Node 3
[ 0.569990] CPU: Physical Processor ID: 3
[ 0.569990] CPU: Processor Core ID: 1
[ 0.569990] x86: PAT support disabled.
[ 0.642314] CPU7: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.644907] Brought up 8 CPUs
[ 0.645904] Total of 8 processors activated (41793.22 BogoMIPS).
[ 1.088430] khelper used greatest stack depth: 6056 bytes left
[ 1.088430] net_namespace: 1176 bytes
[ 1.088561] Time: 12:28:07 Date: 07/09/09
[ 1.088603] NET: Registered protocol family 16
[ 1.182581] No dock devices found.
[ 1.184445] bus: 00 to node: 00
[ 1.184446] bus: 01 to node: 00
[ 1.184447] bus: 02 to node: 00
[ 1.184449] bus: 03 to node: 00
[ 1.184450] bus: 04 to node: 00
[ 1.184451] bus: 05 to node: 00
[ 1.184452] bus: 06 to node: 00
[ 1.184453] bus: 07 to node: 00
[ 1.184454] bus: 08 to node: 00
[ 1.184455] bus: 09 to node: 00
[ 1.184456] bus: 0a to node: 00
[ 1.184457] bus: 0b to node: 00
[ 1.184458] bus: 0c to node: 00
[ 1.184460] bus: 0d to node: 00
[ 1.184461] bus: 0e to node: 00
[ 1.184462] bus: 0f to node: 00
[ 1.184463] bus: 10 to node: 00
[ 1.184464] bus: 11 to node: 00
[ 1.184465] bus: 12 to node: 00
[ 1.184466] bus: 13 to node: 00
[ 1.184467] bus: 14 to node: 00
[ 1.184468] bus: 15 to node: 00
[ 1.184469] bus: 16 to node: 00
[ 1.184471] bus: 17 to node: 00
[ 1.184472] bus: 18 to node: 00
[ 1.184473] bus: 19 to node: 00
[ 1.184474] bus: 1a to node: 00
[ 1.184475] bus: 1b to node: 00
[ 1.184476] bus: 1c to node: 00
[ 1.184477] bus: 1d to node: 00
[ 1.184478] bus: 1e to node: 00
[ 1.184480] bus: 1f to node: 00
[ 1.184481] bus: 20 to node: 00
[ 1.184482] bus: 21 to node: 00
[ 1.184483] bus: 22 to node: 00
[ 1.184484] bus: 23 to node: 00
[ 1.184485] bus: 24 to node: 00
[ 1.184486] bus: 25 to node: 00
[ 1.184487] bus: 26 to node: 00
[ 1.184488] bus: 27 to node: 00
[ 1.184489] bus: 28 to node: 00
[ 1.184491] bus: 29 to node: 00
[ 1.184492] bus: 2a to node: 00
[ 1.184493] bus: 2b to node: 00
[ 1.184494] bus: 2c to node: 00
[ 1.184495] bus: 2d to node: 00
[ 1.184496] bus: 2e to node: 00
[ 1.184497] bus: 2f to node: 00
[ 1.184498] bus: 30 to node: 00
[ 1.184499] bus: 31 to node: 00
[ 1.184501] bus: 32 to node: 00
[ 1.184502] bus: 33 to node: 00
[ 1.184503] bus: 34 to node: 00
[ 1.184504] bus: 35 to node: 00
[ 1.184505] bus: 36 to node: 00
[ 1.184506] bus: 37 to node: 00
[ 1.184507] bus: 38 to node: 00
[ 1.184508] bus: 39 to node: 00
[ 1.184509] bus: 3a to node: 00
[ 1.184510] bus: 3b to node: 00
[ 1.184512] bus: 3c to node: 00
[ 1.184513] bus: 3d to node: 00
[ 1.184514] bus: 3e to node: 00
[ 1.184515] bus: 3f to node: 00
[ 1.184516] bus: 40 to node: 01
[ 1.184517] bus: 41 to node: 01
[ 1.184518] bus: 42 to node: 01
[ 1.184519] bus: 43 to node: 01
[ 1.184520] bus: 44 to node: 01
[ 1.184522] bus: 45 to node: 01
[ 1.184523] bus: 46 to node: 01
[ 1.184524] bus: 47 to node: 01
[ 1.184525] bus: 48 to node: 01
[ 1.184526] bus: 49 to node: 01
[ 1.184527] bus: 4a to node: 01
[ 1.184528] bus: 4b to node: 01
[ 1.184529] bus: 4c to node: 01
[ 1.184530] bus: 4d to node: 01
[ 1.184531] bus: 4e to node: 01
[ 1.184532] bus: 4f to node: 01
[ 1.184534] bus: 50 to node: 01
[ 1.184535] bus: 51 to node: 01
[ 1.184536] bus: 52 to node: 01
[ 1.184537] bus: 53 to node: 01
[ 1.184538] bus: 54 to node: 01
[ 1.184539] bus: 55 to node: 01
[ 1.184540] bus: 56 to node: 01
[ 1.184541] bus: 57 to node: 01
[ 1.184542] bus: 58 to node: 01
[ 1.184543] bus: 59 to node: 01
[ 1.184545] bus: 5a to node: 01
[ 1.184546] bus: 5b to node: 01
[ 1.184547] bus: 5c to node: 01
[ 1.184548] bus: 5d to node: 01
[ 1.184549] bus: 5e to node: 01
[ 1.184550] bus: 5f to node: 01
[ 1.184551] bus: 60 to node: 01
[ 1.184552] bus: 61 to node: 01
[ 1.184553] bus: 62 to node: 01
[ 1.184554] bus: 63 to node: 01
[ 1.184556] bus: 64 to node: 01
[ 1.184557] bus: 65 to node: 01
[ 1.184558] bus: 66 to node: 01
[ 1.184559] bus: 67 to node: 01
[ 1.184560] bus: 68 to node: 01
[ 1.184561] bus: 69 to node: 01
[ 1.184562] bus: 6a to node: 01
[ 1.184563] bus: 6b to node: 01
[ 1.184564] bus: 6c to node: 01
[ 1.184565] bus: 6d to node: 01
[ 1.184566] bus: 6e to node: 01
[ 1.184568] bus: 6f to node: 01
[ 1.184569] bus: 70 to node: 01
[ 1.184570] bus: 71 to node: 01
[ 1.184571] bus: 72 to node: 01
[ 1.184572] bus: 73 to node: 01
[ 1.184573] bus: 74 to node: 01
[ 1.184574] bus: 75 to node: 01
[ 1.184575] bus: 76 to node: 01
[ 1.184576] bus: 77 to node: 01
[ 1.184577] bus: 78 to node: 01
[ 1.184579] bus: 79 to node: 01
[ 1.184580] bus: 7a to node: 01
[ 1.184581] bus: 7b to node: 01
[ 1.184582] bus: 7c to node: 01
[ 1.184583] bus: 7d to node: 01
[ 1.184584] bus: 7e to node: 01
[ 1.184585] bus: 7f to node: 01
[ 1.184610] ACPI: bus type pci registered
[ 1.186388] PCI: Using configuration type 1 for base access
[ 1.192116] ACPI: EC: Look up EC in DSDT
[ 1.195709] ACPI: SSDT 7FD58000, 09BC (r2 HP PNOWSSDT 2 HP 1)
[ 1.199622] ACPI: Interpreter enabled
[ 1.200296] ACPI: (supports S0 S4 S5)
[ 1.202295] ACPI: Using IOAPIC for interrupt routing
[ 1.210458] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 1.211353] PCI: Scanning bus 0000:00
[ 1.211374] PCI: Found 0000:00:00.0 [10de/005e] 000580 00
[ 1.211404] PCI: Found 0000:00:01.0 [10de/0051] 000601 00
[ 1.211415] pci 0000:00:01.0: calling nvidia_force_enable_hpet+0x0/0xa3()
[ 1.211436] PCI: Found 0000:00:02.0 [10de/005a] 000c03 00
[ 1.211458] PCI: Found 0000:00:02.1 [10de/005b] 000c03 00
[ 1.211486] PCI: Found 0000:00:06.0 [10de/0053] 000101 00
[ 1.211504] PCI: Found 0000:00:09.0 [10de/005c] 000604 01
[ 1.211520] PCI: Found 0000:00:0c.0 [10de/005d] 000604 01
[ 1.211535] PCI: Found 0000:00:0d.0 [10de/005d] 000604 01
[ 1.211552] PCI: Found 0000:00:0e.0 [10de/005d] 000604 01
[ 1.211572] PCI: Found 0000:00:18.0 [1022/1100] 000600 00
[ 1.211583] PCI: Found 0000:00:18.1 [1022/1101] 000600 00
[ 1.211593] PCI: Found 0000:00:18.2 [1022/1102] 000600 00
[ 1.211605] PCI: Found 0000:00:18.3 [1022/1103] 000600 00
[ 1.211619] PCI: Found 0000:00:19.0 [1022/1100] 000600 00
[ 1.211631] PCI: Found 0000:00:19.1 [1022/1101] 000600 00
[ 1.211641] PCI: Found 0000:00:19.2 [1022/1102] 000600 00
[ 1.211653] PCI: Found 0000:00:19.3 [1022/1103] 000600 00
[ 1.211669] PCI: Found 0000:00:1a.0 [1022/1100] 000600 00
[ 1.211680] PCI: Found 0000:00:1a.1 [1022/1101] 000600 00
[ 1.211691] PCI: Found 0000:00:1a.2 [1022/1102] 000600 00
[ 1.211703] PCI: Found 0000:00:1a.3 [1022/1103] 000600 00
[ 1.211719] PCI: Found 0000:00:1b.0 [1022/1100] 000600 00
[ 1.211732] PCI: Found 0000:00:1b.1 [1022/1101] 000600 00
[ 1.211744] PCI: Found 0000:00:1b.2 [1022/1102] 000600 00
[ 1.211759] PCI: Found 0000:00:1b.3 [1022/1103] 000600 00
[ 1.211772] PCI: Fixups for bus 0000:00
[ 1.211775] PCI: Scanning behind PCI bridge 0000:00:09.0, config 010100, pass 0
[ 1.211779] PCI: Scanning bus 0000:01
[ 1.211795] PCI: Found 0000:01:03.0 [1002/515e] 000300 00
[ 1.211835] PCI: Found 0000:01:04.0 [0e11/b203] 000880 00
[ 1.211877] PCI: Found 0000:01:04.2 [0e11/b204] 000880 00
[ 1.211927] PCI: Found 0000:01:04.4 [103c/3300] 000c03 00
[ 1.211974] PCI: Found 0000:01:04.6 [103c/3302] 000c07 00
[ 1.212022] PCI: Fixups for bus 0000:01
[ 1.212024] PCI: Transparent bridge - 0000:00:09.0
[ 1.212296] PCI: Bus scan for 0000:01 returning with max=01
[ 1.212298] PCI: Scanning behind PCI bridge 0000:00:0c.0, config 0a0800, pass 0
[ 1.212302] PCI: Scanning bus 0000:08
[ 1.212329] PCI: Fixups for bus 0000:08
[ 1.212333] PCI: Bus scan for 0000:08 returning with max=08
[ 1.212335] PCI: Scanning behind PCI bridge 0000:00:0d.0, config 070500, pass 0
[ 1.212341] PCI: Scanning bus 0000:05
[ 1.212368] PCI: Fixups for bus 0000:05
[ 1.212372] PCI: Bus scan for 0000:05 returning with max=05
[ 1.212374] PCI: Scanning behind PCI bridge 0000:00:0e.0, config 040200, pass 0
[ 1.212377] PCI: Scanning bus 0000:02
[ 1.212404] PCI: Fixups for bus 0000:02
[ 1.212408] PCI: Bus scan for 0000:02 returning with max=02
[ 1.212411] PCI: Scanning behind PCI bridge 0000:00:09.0, config 010100, pass 1
[ 1.212413] PCI: Scanning behind PCI bridge 0000:00:0c.0, config 0a0800, pass 1
[ 1.212416] PCI: Scanning behind PCI bridge 0000:00:0d.0, config 070500, pass 1
[ 1.212419] PCI: Scanning behind PCI bridge 0000:00:0e.0, config 040200, pass 1
[ 1.212422] PCI: Bus scan for 0000:00 returning with max=0a
[ 1.212428] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.212529] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IP2P._PRT]
[ 1.212670] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE0._PRT]
[ 1.212796] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE1._PRT]
[ 1.212922] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE2._PRT]
[ 1.216542] ACPI: PCI Root Bridge [PCI1] (0000:40)
[ 1.217349] PCI: Scanning bus 0000:40
[ 1.217368] PCI: Found 0000:40:00.0 [10de/005e] 000580 00
[ 1.217400] PCI: Found 0000:40:01.0 [10de/00d3] 000580 00
[ 1.217438] PCI: Found 0000:40:0b.0 [10de/005d] 000604 01
[ 1.217459] PCI: Found 0000:40:0c.0 [10de/005d] 000604 01
[ 1.217481] PCI: Found 0000:40:0d.0 [10de/005d] 000604 01
[ 1.217502] PCI: Found 0000:40:0e.0 [10de/005d] 000604 01
[ 1.217527] PCI: Found 0000:40:10.0 [1022/7458] 000604 01
[ 1.217542] PCI: Found 0000:40:10.1 [1022/7459] 000800 00
[ 1.217574] PCI: Found 0000:40:11.0 [1022/7458] 000604 01
[ 1.217590] PCI: Found 0000:40:11.1 [1022/7459] 000800 00
[ 1.217618] PCI: Fixups for bus 0000:40
[ 1.217620] PCI: Scanning behind PCI bridge 0000:40:0b.0, config 514f40, pass 0
[ 1.217626] PCI: Scanning bus 0000:4f
[ 1.217650] PCI: Fixups for bus 0000:4f
[ 1.217656] PCI: Bus scan for 0000:4f returning with max=4f
[ 1.217658] PCI: Scanning behind PCI bridge 0000:40:0c.0, config 4e4c40, pass 0
[ 1.217662] PCI: Scanning bus 0000:4c
[ 1.217687] PCI: Fixups for bus 0000:4c
[ 1.217692] PCI: Bus scan for 0000:4c returning with max=4c
[ 1.217695] PCI: Scanning behind PCI bridge 0000:40:0d.0, config 4b4940, pass 0
[ 1.217699] PCI: Scanning bus 0000:49
[ 1.217723] PCI: Fixups for bus 0000:49
[ 1.217728] PCI: Bus scan for 0000:49 returning with max=49
[ 1.217731] PCI: Scanning behind PCI bridge 0000:40:0e.0, config 484640, pass 0
[ 1.217735] PCI: Scanning bus 0000:46
[ 1.217759] PCI: Fixups for bus 0000:46
[ 1.217764] PCI: Bus scan for 0000:46 returning with max=46
[ 1.217767] PCI: Scanning behind PCI bridge 0000:40:10.0, config 414140, pass 0
[ 1.217772] PCI: Scanning bus 0000:41
[ 1.217790] PCI: Found 0000:41:01.0 [14e4/164a] 000200 00
[ 1.217828] PCI: Found 0000:41:02.0 [14e4/164a] 000200 00
[ 1.217866] PCI: Fixups for bus 0000:41
[ 1.217872] PCI: Bus scan for 0000:41 returning with max=41
[ 1.217875] PCI: Scanning behind PCI bridge 0000:40:11.0, config 454240, pass 0
[ 1.217878] PCI: Scanning bus 0000:42
[ 1.217897] PCI: Found 0000:42:01.0 [1000/0054] 000100 00
[ 1.217936] PCI: Found 0000:42:02.0 [103c/3220] 000104 00
[ 1.217975] PCI: Fixups for bus 0000:42
[ 1.217980] PCI: Bus scan for 0000:42 returning with max=42
[ 1.217983] PCI: Scanning behind PCI bridge 0000:40:0b.0, config 514f40, pass 1
[ 1.217986] PCI: Scanning behind PCI bridge 0000:40:0c.0, config 4e4c40, pass 1
[ 1.217990] PCI: Scanning behind PCI bridge 0000:40:0d.0, config 4b4940, pass 1
[ 1.217993] PCI: Scanning behind PCI bridge 0000:40:0e.0, config 484640, pass 1
[ 1.217996] PCI: Scanning behind PCI bridge 0000:40:10.0, config 414140, pass 1
[ 1.218000] PCI: Scanning behind PCI bridge 0000:40:11.0, config 454240, pass 1
[ 1.218003] PCI: Bus scan for 0000:40 returning with max=51
[ 1.218010] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.BRGA._PRT]
[ 1.218126] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.BRGB._PRT]
[ 1.218341] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE0._PRT]
[ 1.218487] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE1._PRT]
[ 1.218632] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE2._PRT]
[ 1.218778] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE3._PRT]
[ 1.220812] ACPI: PCI Interrupt Link [LNKW] (IRQs 16) *0, disabled.
[ 1.223402] ACPI: PCI Interrupt Link [LNKX] (IRQs 17) *0, disabled.
[ 1.226455] ACPI: PCI Interrupt Link [LNKY] (IRQs 18) *0, disabled.
[ 1.229697] ACPI: PCI Interrupt Link [LNKZ] (IRQs 19) *0, disabled.
[ 1.234435] ACPI: PCI Interrupt Link [LNU0] (IRQs 22) *5
[ 1.237452] ACPI: PCI Interrupt Link [LNU2] (IRQs 23) *10
[ 1.240770] ACPI: PCI Interrupt Link [LNKA] (IRQs 54) *0, disabled.
[ 1.244451] ACPI: PCI Interrupt Link [LNKB] (IRQs 55) *0, disabled.
[ 1.247408] ACPI: PCI Interrupt Link [LNKC] (IRQs 56) *0, disabled.
[ 1.251447] ACPI: PCI Interrupt Link [LNKD] (IRQs 57) *0, disabled.
[ 1.253787] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 1.254334] pnp: PnP ACPI init
[ 1.255292] ACPI: bus type pnp registered
[ 1.261061] pnp: PnP ACPI: found 16 devices
[ 1.261286] ACPI: ACPI bus type pnp unregistered
[ 1.262685] SCSI subsystem initialized
[ 1.263532] libata version 3.00 loaded.
[ 1.263691] usbcore: registered new interface driver usbfs
[ 1.265306] usbcore: registered new interface driver hub
[ 1.266353] usbcore: registered new device driver usb
[ 1.267672] PCI: Using ACPI for IRQ routing
[ 1.276302] NetLabel: Initializing
[ 1.277284] NetLabel: domain hash size = 128
[ 1.278283] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.279294] NetLabel: unlabeled traffic allowed by default
[ 1.280284] DMAR:parse DMAR table failure.
[ 1.281391] PCI-DMA: Disabling AGP.
[ 1.284054] PCI-DMA: aperture base @ 4000000 size 65536 KB
[ 1.284282] PCI-DMA: using GART IOMMU.
[ 1.285284] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 1.286907] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[ 1.290281] hpet0: 3 32-bit timers, 25000000 Hz
[ 1.293022] ACPI: RTC can wake from S4
[ 1.293288] Switched to high resolution mode on CPU 0
[ 2.725661] Switched to high resolution mode on CPU 4
[ 3.352629] Switched to high resolution mode on CPU 1
[ 3.352629] Switched to high resolution mode on CPU 5
[ 3.352629] Switched to high resolution mode on CPU 2
[ 3.352629] Switched to high resolution mode on CPU 6
[ 3.352629] Switched to high resolution mode on CPU 3
[ 3.352629] Switched to high resolution mode on CPU 7
[ 3.352629] system 00:01: ioport range 0x408-0x40f has been reserved
[ 3.388529] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 3.423688] system 00:01: ioport range 0x700-0x73f has been reserved
[ 3.459756] system 00:01: ioport range 0x800-0x8fe has been reserved
[ 3.495519] system 00:01: ioport range 0x900-0x9fe has been reserved
[ 3.531540] system 00:01: ioport range 0x9ff-0x9ff has been reserved
[ 3.567536] system 00:01: ioport range 0xa00-0xafe has been reserved
[ 3.590680] system 00:01: ioport range 0xaff-0xaff has been reserved
[ 3.626541] system 00:01: ioport range 0xb00-0xbfe has been reserved
[ 3.662526] system 00:01: ioport range 0xbff-0xbff has been reserved
[ 3.698548] system 00:01: ioport range 0xc80-0xc83 has been reserved
[ 3.734557] system 00:01: ioport range 0xcd4-0xcd7 has been reserved
[ 3.770555] system 00:01: ioport range 0xcf9-0xcf9 could not be reserved
[ 3.797525] system 00:01: ioport range 0xf50-0xf58 has been reserved
[ 3.834520] system 00:01: ioport range 0xca0-0xca1 has been reserved
[ 3.864128] system 00:01: ioport range 0xca4-0xca5 has been reserved
[ 3.900454] system 00:01: ioport range 0xc00-0xc03 has been reserved
[ 3.936551] system 00:01: ioport range 0x2f8-0x2ff has been reserved
[ 3.972510] got res [d9d00000:d9d1ffff] bus [d9d00000:d9d1ffff] flags 27200 for BAR 6 of 0000:01:03.0
[ 3.972513] got res [d9d20000:d9d2ffff] bus [d9d20000:d9d2ffff] flags 27200 for BAR 6 of 0000:01:04.2
[ 3.972516] PCI: Bridge: 0000:00:09.0
[ 3.992515] IO window: 1000-2fff
[ 4.012496] MEM window: 0xd9d00000-0xd9efffff
[ 4.037514] PREFETCH window: 0x00000000d0000000-0x00000000d7ffffff
[ 4.074774] PCI: Bridge: 0000:00:0c.0
[ 4.094929] IO window: disabled.
[ 4.114657] MEM window: disabled.
[ 4.133531] PREFETCH window: disabled.
[ 4.156511] PCI: Bridge: 0000:00:0d.0
[ 4.176430] IO window: disabled.
[ 4.197533] MEM window: disabled.
[ 4.216509] PREFETCH window: disabled.
[ 4.229402] PCI: Bridge: 0000:00:0e.0
[ 4.238533] IO window: disabled.
[ 4.258529] MEM window: disabled.
[ 4.277504] PREFETCH window: disabled.
[ 4.287668] PCI: Setting latency timer of device 0000:00:09.0 to 64
[ 4.287676] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 4.287680] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 4.287686] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 4.287693] PCI: Bridge: 0000:40:0b.0
[ 4.307503] IO window: disabled.
[ 4.327512] MEM window: disabled.
[ 4.346513] PREFETCH window: disabled.
[ 4.369482] PCI: Bridge: 0000:40:0c.0
[ 4.389473] IO window: disabled.
[ 4.409485] MEM window: disabled.
[ 4.428488] PREFETCH window: disabled.
[ 4.451874] PCI: Bridge: 0000:40:0d.0
[ 4.461515] IO window: disabled.
[ 4.481522] MEM window: disabled.
[ 4.486756] PREFETCH window: disabled.
[ 4.509625] PCI: Bridge: 0000:40:0e.0
[ 4.520352] IO window: disabled.
[ 4.539524] MEM window: disabled.
[ 4.559516] PREFETCH window: disabled.
[ 4.582507] got res [88000000:8801ffff] bus [88000000:8801ffff] flags 27200 for BAR 6 of 0000:41:01.0
[ 4.582510] got res [88020000:8803ffff] bus [88020000:8803ffff] flags 27200 for BAR 6 of 0000:41:02.0
[ 4.582512] PCI: Bridge: 0000:40:10.0
[ 4.602523] IO window: disabled.
[ 4.615159] MEM window: 0xda000000-0xddffffff
[ 4.640481] PREFETCH window: 0x0000000088000000-0x00000000880fffff
[ 4.678495] got res [88200000:883fffff] bus [88200000:883fffff] flags 27200 for BAR 6 of 0000:42:01.0
[ 4.678498] got res [88100000:8813ffff] bus [88100000:8813ffff] flags 27200 for BAR 6 of 0000:42:02.0
[ 4.678500] PCI: Bridge: 0000:40:11.0
[ 4.681178] IO window: 3000-3fff
[ 4.700521] MEM window: 0xdfe00000-0xdfefffff
[ 4.725474] PREFETCH window: 0x0000000088100000-0x00000000883fffff
[ 4.763491] PCI: Setting latency timer of device 0000:40:0b.0 to 64
[ 4.763497] PCI: Setting latency timer of device 0000:40:0c.0 to 64
[ 4.763504] PCI: Setting latency timer of device 0000:40:0d.0 to 64
[ 4.763511] PCI: Setting latency timer of device 0000:40:0e.0 to 64
[ 4.763545] NET: Registered protocol family 2
[ 4.797927] IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 4.844411] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 4.893908] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 4.932131] TCP: Hash tables configured (established 524288 bind 65536)
[ 4.950137] TCP reno registered
[ 4.970657] NET: Registered protocol family 1
[ 4.988167] checking if image is initramfs... it is
[ 5.154400] Freeing initrd memory: 2668k freed
[ 5.184553] microcode: CPU0 not a capable Intel processor
[ 5.189397] microcode: CPU1 not a capable Intel processor
[ 5.200319] microcode: CPU2 not a capable Intel processor
[ 5.230377] microcode: CPU3 not a capable Intel processor
[ 5.230377] microcode: CPU4 not a capable Intel processor
[ 5.286358] microcode: CPU5 not a capable Intel processor
[ 5.317838] microcode: CPU6 not a capable Intel processor
[ 5.347929] microcode: CPU7 not a capable Intel processor
[ 5.385623] IA-32 Microcode Update Driver: v1.14a <tigran@xxxxxxxxxxxxxxxxxxxx>
[ 5.408176] audit: initializing netlink socket (disabled)
[ 5.438396] type=2000 audit(1247142486.936:1): initialized
[ 5.455629] Total HugeTLB memory allocated, 0
[ 5.483721] VFS: Disk quotas dquot_6.5.1
[ 5.496000] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 5.522917] SELinux: Registering netfilter hooks
[ 5.523129] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 5.541903] io scheduler noop registered
[ 5.564642] io scheduler anticipatory registered
[ 5.587007] io scheduler deadline registered
[ 5.611782] io scheduler cfq registered (default)
[ 5.637654] pci 0000:00:00.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.637676] pci 0000:00:00.0: Enabling HT MSI Mapping
[ 5.644615] pci 0000:00:00.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.644622] pci 0000:00:00.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.644626] pci 0000:00:00.0: calling pci_fixup_video+0x0/0xaf()
[ 5.644631] pci 0000:00:01.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.644637] pci 0000:00:01.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.644640] pci 0000:00:01.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.644643] pci 0000:00:01.0: calling pci_fixup_video+0x0/0xaf()
[ 5.644647] pci 0000:00:02.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.644655] pci 0000:00:02.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.644657] pci 0000:00:02.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.655224] pci 0000:00:02.0: calling pci_fixup_video+0x0/0xaf()
[ 5.655228] pci 0000:00:02.1: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.655237] pci 0000:00:02.1: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.655240] pci 0000:00:02.1: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.655247] pci 0000:00:02.1: EHCI: BIOS handoff
[ 5.666221] pci 0000:00:02.1: calling pci_fixup_video+0x0/0xaf()
[ 5.666225] pci 0000:00:06.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.666233] pci 0000:00:06.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.666235] pci 0000:00:06.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.666238] pci 0000:00:06.0: calling pci_fixup_video+0x0/0xaf()
[ 5.666242] pci 0000:00:09.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.666249] pci 0000:00:09.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.666251] pci 0000:00:09.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.666254] pci 0000:00:09.0: calling pci_fixup_video+0x0/0xaf()
[ 5.666258] pci 0000:00:0c.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.666267] pci 0000:00:0c.0: Enabling HT MSI Mapping
[ 5.694224] pci 0000:00:0c.0: calling quirk_nvidia_ck804_msi_ht_cap+0x0/0x7a()
[ 5.694232] pci 0000:00:0c.0: Found enabled HT MSI Mapping
[ 5.712408] pci 0000:00:0c.0: calling quirk_nvidia_ck804_pcie_aer_ext_cap+0x0/0x6a()
[ 5.712411] pci 0000:00:0c.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.712414] pci 0000:00:0c.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.712417] pci 0000:00:0c.0: calling pci_fixup_video+0x0/0xaf()
[ 5.712421] pci 0000:00:0d.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.712430] pci 0000:00:0d.0: Enabling HT MSI Mapping
[ 5.720120] pci 0000:00:0d.0: calling quirk_nvidia_ck804_msi_ht_cap+0x0/0x7a()
[ 5.720127] pci 0000:00:0d.0: Found enabled HT MSI Mapping
[ 5.729153] pci 0000:00:0d.0: calling quirk_nvidia_ck804_pcie_aer_ext_cap+0x0/0x6a()
[ 5.729156] pci 0000:00:0d.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.729159] pci 0000:00:0d.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.729162] pci 0000:00:0d.0: calling pci_fixup_video+0x0/0xaf()
[ 5.729166] pci 0000:00:0e.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.729175] pci 0000:00:0e.0: Enabling HT MSI Mapping
[ 5.757220] pci 0000:00:0e.0: calling quirk_nvidia_ck804_msi_ht_cap+0x0/0x7a()
[ 5.757227] pci 0000:00:0e.0: Found enabled HT MSI Mapping
[ 5.789219] pci 0000:00:0e.0: calling quirk_nvidia_ck804_pcie_aer_ext_cap+0x0/0x6a()
[ 5.789222] pci 0000:00:0e.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789225] pci 0000:00:0e.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789227] pci 0000:00:0e.0: calling pci_fixup_video+0x0/0xaf()
[ 5.789231] pci 0000:00:18.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789234] pci 0000:00:18.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789237] pci 0000:00:18.0: calling pci_fixup_video+0x0/0xaf()
[ 5.789241] pci 0000:00:18.1: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789244] pci 0000:00:18.1: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789247] pci 0000:00:18.1: calling pci_fixup_video+0x0/0xaf()
[ 5.789251] pci 0000:00:18.2: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789254] pci 0000:00:18.2: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789256] pci 0000:00:18.2: calling pci_fixup_video+0x0/0xaf()
[ 5.789261] pci 0000:00:18.3: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789263] pci 0000:00:18.3: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789266] pci 0000:00:18.3: calling pci_fixup_video+0x0/0xaf()
[ 5.789270] pci 0000:00:19.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789273] pci 0000:00:19.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789276] pci 0000:00:19.0: calling pci_fixup_video+0x0/0xaf()
[ 5.789280] pci 0000:00:19.1: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789282] pci 0000:00:19.1: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789285] pci 0000:00:19.1: calling pci_fixup_video+0x0/0xaf()
[ 5.789290] pci 0000:00:19.2: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789292] pci 0000:00:19.2: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789295] pci 0000:00:19.2: calling pci_fixup_video+0x0/0xaf()
[ 5.789299] pci 0000:00:19.3: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789302] pci 0000:00:19.3: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789305] pci 0000:00:19.3: calling pci_fixup_video+0x0/0xaf()
[ 5.789309] pci 0000:00:1a.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789311] pci 0000:00:1a.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789314] pci 0000:00:1a.0: calling pci_fixup_video+0x0/0xaf()
[ 5.789318] pci 0000:00:1a.1: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789321] pci 0000:00:1a.1: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789324] pci 0000:00:1a.1: calling pci_fixup_video+0x0/0xaf()
[ 5.789328] pci 0000:00:1a.2: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789331] pci 0000:00:1a.2: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789334] pci 0000:00:1a.2: calling pci_fixup_video+0x0/0xaf()
[ 5.789338] pci 0000:00:1a.3: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789341] pci 0000:00:1a.3: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789343] pci 0000:00:1a.3: calling pci_fixup_video+0x0/0xaf()
[ 5.789348] pci 0000:00:1b.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789350] pci 0000:00:1b.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789353] pci 0000:00:1b.0: calling pci_fixup_video+0x0/0xaf()
[ 5.789357] pci 0000:00:1b.1: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789360] pci 0000:00:1b.1: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789363] pci 0000:00:1b.1: calling pci_fixup_video+0x0/0xaf()
[ 5.789367] pci 0000:00:1b.2: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789370] pci 0000:00:1b.2: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789373] pci 0000:00:1b.2: calling pci_fixup_video+0x0/0xaf()
[ 5.789377] pci 0000:00:1b.3: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789379] pci 0000:00:1b.3: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789382] pci 0000:00:1b.3: calling pci_fixup_video+0x0/0xaf()
[ 5.789386] pci 0000:01:03.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789389] pci 0000:01:03.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789392] pci 0000:01:03.0: calling pci_fixup_video+0x0/0xaf()
[ 5.789396] pci 0000:01:03.0: Boot video device
[ 5.789399] pci 0000:01:04.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789402] pci 0000:01:04.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789405] pci 0000:01:04.0: calling pci_fixup_video+0x0/0xaf()
[ 5.789409] pci 0000:01:04.2: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789411] pci 0000:01:04.2: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789414] pci 0000:01:04.2: calling pci_fixup_video+0x0/0xaf()
[ 5.789418] pci 0000:01:04.4: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.789421] pci 0000:01:04.4: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.789428] pci 0000:01:04.4: uhci_check_and_reset_hc: legsup = 0x0010
[ 5.789429] pci 0000:01:04.4: Performing full reset
[ 5.789439] pci 0000:01:04.4: HCRESET not completed yet!
[ 5.819124] pci 0000:01:04.4: calling pci_fixup_video+0x0/0xaf()
[ 5.819128] pci 0000:01:04.6: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.819131] pci 0000:01:04.6: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.819134] pci 0000:01:04.6: calling pci_fixup_video+0x0/0xaf()
[ 5.819139] pci 0000:40:00.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.819151] pci 0000:40:00.0: Enabling HT MSI Mapping
[ 5.837123] pci 0000:40:00.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.837126] pci 0000:40:00.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.837129] pci 0000:40:00.0: calling pci_fixup_video+0x0/0xaf()
[ 5.837133] pci 0000:40:01.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.837139] pci 0000:40:01.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.837142] pci 0000:40:01.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.837145] pci 0000:40:01.0: calling pci_fixup_video+0x0/0xaf()
[ 5.837149] pci 0000:40:0b.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.837159] pci 0000:40:0b.0: Enabling HT MSI Mapping
[ 5.855364] pci 0000:40:0b.0: calling quirk_nvidia_ck804_msi_ht_cap+0x0/0x7a()
[ 5.855371] pci 0000:40:0b.0: Found enabled HT MSI Mapping
[ 5.871444] pci 0000:40:0b.0: calling quirk_nvidia_ck804_pcie_aer_ext_cap+0x0/0x6a()
[ 5.871447] pci 0000:40:0b.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.871450] pci 0000:40:0b.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.871453] pci 0000:40:0b.0: calling pci_fixup_video+0x0/0xaf()
[ 5.871457] pci 0000:40:0c.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.871467] pci 0000:40:0c.0: Enabling HT MSI Mapping
[ 5.899129] pci 0000:40:0c.0: calling quirk_nvidia_ck804_msi_ht_cap+0x0/0x7a()
[ 5.899137] pci 0000:40:0c.0: Found enabled HT MSI Mapping
[ 5.931121] pci 0000:40:0c.0: calling quirk_nvidia_ck804_pcie_aer_ext_cap+0x0/0x6a()
[ 5.931125] pci 0000:40:0c.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.931127] pci 0000:40:0c.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.931130] pci 0000:40:0c.0: calling pci_fixup_video+0x0/0xaf()
[ 5.931134] pci 0000:40:0d.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.931144] pci 0000:40:0d.0: Enabling HT MSI Mapping
[ 5.941704] pci 0000:40:0d.0: calling quirk_nvidia_ck804_msi_ht_cap+0x0/0x7a()
[ 5.941711] pci 0000:40:0d.0: Found enabled HT MSI Mapping
[ 5.973118] pci 0000:40:0d.0: calling quirk_nvidia_ck804_pcie_aer_ext_cap+0x0/0x6a()
[ 5.973122] pci 0000:40:0d.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.973124] pci 0000:40:0d.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.973127] pci 0000:40:0d.0: calling pci_fixup_video+0x0/0xaf()
[ 5.973132] pci 0000:40:0e.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.973141] pci 0000:40:0e.0: Enabling HT MSI Mapping
[ 6.001113] pci 0000:40:0e.0: calling quirk_nvidia_ck804_msi_ht_cap+0x0/0x7a()
[ 6.001120] pci 0000:40:0e.0: Found enabled HT MSI Mapping
[ 6.033111] pci 0000:40:0e.0: calling quirk_nvidia_ck804_pcie_aer_ext_cap+0x0/0x6a()
[ 6.033115] pci 0000:40:0e.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 6.033117] pci 0000:40:0e.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 6.033120] pci 0000:40:0e.0: calling pci_fixup_video+0x0/0xaf()
[ 6.033125] pci 0000:40:10.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 6.033127] pci 0000:40:10.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 6.033130] pci 0000:40:10.0: calling pci_fixup_video+0x0/0xaf()
[ 6.033135] pci 0000:40:10.1: calling quirk_cardbus_legacy+0x0/0x1d()
[ 6.033137] pci 0000:40:10.1: calling quirk_usb_early_handoff+0x0/0x447()
[ 6.033140] pci 0000:40:10.1: calling pci_fixup_video+0x0/0xaf()
[ 6.033144] pci 0000:40:11.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 6.033147] pci 0000:40:11.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 6.033150] pci 0000:40:11.0: calling pci_fixup_video+0x0/0xaf()
[ 6.033154] pci 0000:40:11.1: calling quirk_cardbus_legacy+0x0/0x1d()
[ 6.033157] pci 0000:40:11.1: calling quirk_usb_early_handoff+0x0/0x447()
[ 6.033160] pci 0000:40:11.1: calling pci_fixup_video+0x0/0xaf()
[ 6.033165] pci 0000:41:01.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 6.033167] pci 0000:41:01.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 6.033170] pci 0000:41:01.0: calling pci_fixup_video+0x0/0xaf()
[ 6.033174] pci 0000:41:02.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 6.033177] pci 0000:41:02.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 6.033180] pci 0000:41:02.0: calling pci_fixup_video+0x0/0xaf()
[ 6.033184] pci 0000:42:01.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 6.033187] pci 0000:42:01.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 6.033190] pci 0000:42:01.0: calling pci_fixup_video+0x0/0xaf()
[ 6.033194] pci 0000:42:02.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 6.033197] pci 0000:42:02.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 6.033200] pci 0000:42:02.0: calling pci_fixup_video+0x0/0xaf()
[ 6.033443] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 6.033459] assign_interrupt_mode Found MSI capability
[ 6.052207] Allocate Port Service[0000:00:0c.0:pcie00]
[ 6.053277] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 6.053290] assign_interrupt_mode Found MSI capability
[ 6.079464] Allocate Port Service[0000:00:0d.0:pcie00]
[ 6.079544] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 6.079556] assign_interrupt_mode Found MSI capability
[ 6.109173] Allocate Port Service[0000:00:0e.0:pcie00]
[ 6.109173] PCI: Setting latency timer of device 0000:40:0b.0 to 64
[ 6.109195] assign_interrupt_mode Found MSI capability
[ 6.134444] Allocate Port Service[0000:40:0b.0:pcie00]
[ 6.134557] PCI: Setting latency timer of device 0000:40:0c.0 to 64
[ 6.134575] assign_interrupt_mode Found MSI capability
[ 6.163478] Allocate Port Service[0000:40:0c.0:pcie00]
[ 6.163562] PCI: Setting latency timer of device 0000:40:0d.0 to 64
[ 6.163581] assign_interrupt_mode Found MSI capability
[ 6.192057] Allocate Port Service[0000:40:0d.0:pcie00]
[ 6.193061] PCI: Setting latency timer of device 0000:40:0e.0 to 64
[ 6.193079] assign_interrupt_mode Found MSI capability
[ 6.222003] Allocate Port Service[0000:40:0e.0:pcie00]
[ 6.223184] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 6.256181] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 6.300997] ACPI: Power Button (FF) [PWRF]
[ 6.326163] ACPI: ACPI0007:00 is registered as cooling_device0
[ 6.348810] ACPI: ACPI0007:01 is registered as cooling_device1
[ 6.365295] ACPI: ACPI0007:02 is registered as cooling_device2
[ 6.373940] ACPI: ACPI0007:03 is registered as cooling_device3
[ 6.406765] ACPI: ACPI0007:04 is registered as cooling_device4
[ 6.440714] ACPI: ACPI0007:05 is registered as cooling_device5
[ 6.473667] ACPI: ACPI0007:06 is registered as cooling_device6
[ 6.496598] ACPI: ACPI0007:07 is registered as cooling_device7
[ 6.540851] hpet_resources: 0xfed00000 is busy
[ 6.541011] Non-volatile memory driver v1.2
[ 6.563623] Linux agpgart interface v0.103
[ 6.588627] [drm] Initialized drm 1.1.0 20060810
[ 6.615550] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 6.907490] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 7.189215] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 7.213505] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 7.246638] brd: module loaded
[ 7.265662] loop: module loaded
[ 7.282964] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 7.308127] Copyright (c) 1999-2006 Intel Corporation.
[ 7.338048] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
[ 7.363751] e100: Copyright(c) 1999-2006 Intel Corporation
[ 7.396076] Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.7.4 (February 18, 2008)
[ 7.442111] ACPI: PCI Interrupt 0000:41:01.0[A] -> GSI 31 (level, low) -> IRQ 31
[ 7.816164] eth0: Broadcom NetXtreme II BCM5706 1000Base-T (A2) PCI-X 64-bit 100MHz found at mem dc000000, IRQ 31, node addr 00:1b:78:be:d1:50
[ 7.846814] ACPI: PCI Interrupt 0000:41:02.0[A] -> GSI 32 (level, low) -> IRQ 32
[ 8.219180] eth1: Broadcom NetXtreme II BCM5706 1000Base-T (A2) PCI-X 64-bit 100MHz found at mem da000000, IRQ 32, node addr 00:1b:78:be:d1:52
[ 8.292662] console [netcon0] enabled
[ 8.313040] netconsole: network logging started
[ 8.340103] input: Macintosh mouse button emulation as /devices/virtual/input/input1
[ 8.385503] Loading iSCSI transport class v2.0-869.
[ 8.412684] Driver 'sd' needs updating - please use bus_type methods
[ 8.449063] Driver 'sr' needs updating - please use bus_type methods
[ 8.463577] pata_amd 0000:00:06.0: version 0.3.10
[ 8.463619] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 8.463740] scsi0 : pata_amd
[ 8.465551] scsi1 : pata_amd
[ 8.481296] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x500 irq 14
[ 8.520248] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x508 irq 15
[ 8.725233] ata1.00: ATAPI: TEAC DV-W28ECW, G.C4, max MWDMA2
[ 8.758420] ata1: nv_mode_filter: 0x39f&0xfffff->0x39f, BIOS=0x0 (0x0) ACPI=0x0
[ 8.781313] ata1.00: configured for MWDMA2
[ 8.804086] ata2: port disabled. ignoring.
[ 8.816510] scsi 0:0:0:0: CD-ROM TEAC DV-W28ECW G.C4 PQ: 0 ANSI: 5
[ 8.891267] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 8.926113] Uniform CD-ROM driver Revision: 3.20
[ 8.951875] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 8.951994] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 8.982145] ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
[ 8.982435] ACPI: PCI Interrupt Link [LNU2] enabled at IRQ 23
[ 9.014796] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LNU2] -> GSI 23 (level, high) -> IRQ 23
[ 9.047330] PCI: Setting latency timer of device 0000:00:02.1 to 64
[ 9.047332] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 9.076313] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[ 9.119356] ehci_hcd 0000:00:02.1: reset hcs_params 0x10148a dbg=1 cc=1 pcc=4 !ppc ports=10
[ 9.119363] ehci_hcd 0000:00:02.1: reset portroute 0 0 0 0 0 0 0 0 0 0
[ 9.119365] ehci_hcd 0000:00:02.1: reset hcc_params a086 caching frame 256/512/1024 park
[ 9.119386] ehci_hcd 0000:00:02.1: park 0
[ 9.119390] ehci_hcd 0000:00:02.1: reset command 080b12 park=3 ithresh=8 Periodic period=1024 Reset HALT
[ 9.119392] ehci_hcd 0000:00:02.1: bogus port configuration: cc=1 x pcc=4 < ports=10
[ 9.119398] ehci_hcd 0000:00:02.1: debug port 1
[ 9.144196] PCI: cache line size of 64 is not supported by device 0000:00:02.1
[ 9.144198] ehci_hcd 0000:00:02.1: supports USB remote wakeup
[ 9.144208] ehci_hcd 0000:00:02.1: irq 23, io mem 0xd9cd0000
[ 9.177210] ehci_hcd 0000:00:02.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
[ 9.177214] ehci_hcd 0000:00:02.1: init command 010009 (park)=0 ithresh=1 period=256 RUN
[ 9.182213] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 9.224526] usb usb1: default language 0x0409
[ 9.224544] usb usb1: uevent
[ 9.224596] usb usb1: usb_probe_device
[ 9.224718] usb usb1: configuration #1 chosen from 1 choice
[ 9.251790] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 9.251800] usb 1-0:1.0: uevent
[ 9.251845] hub 1-0:1.0: usb_probe_interface
[ 9.251847] hub 1-0:1.0: usb_probe_interface - got id
[ 9.251849] hub 1-0:1.0: USB hub found
[ 9.273301] hub 1-0:1.0: 10 ports detected
[ 9.296584] hub 1-0:1.0: standalone hub
[ 9.296585] hub 1-0:1.0: no power switching (usb 1.0)
[ 9.296587] hub 1-0:1.0: individual port over-current protection
[ 9.296589] hub 1-0:1.0: power on to power good time: 20ms
[ 9.296593] hub 1-0:1.0: local power source is good
[ 9.296595] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 9.392436] hub 1-0:1.0: state 7 ports 10 chg 0000 evt 0000
[ 9.397652] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 9.397652] ehci_hcd 0000:00:02.1: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
[ 9.397658] hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
[ 9.436121] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 9.466835] usb usb1: Product: EHCI Host Controller
[ 9.494689] usb usb1: Manufacturer: Linux 2.6.25 ehci_hcd
[ 9.501872] hub 1-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501
[ 9.525704] usb usb1: SerialNumber: 0000:00:02.1
[ 9.552753] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 9.552756] ohci_hcd: block sizes: ed 80 td 96
[ 9.552977] ACPI: PCI Interrupt Link [LNU0] enabled at IRQ 22
[ 9.553085] ehci_hcd 0000:00:02.1: port 6 high speed
[ 9.553088] ehci_hcd 0000:00:02.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
[ 9.568193] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNU0] -> GSI 22 (level, high) -> IRQ 22
[ 9.603879] usb 1-6: new high speed USB device using ehci_hcd and address 2
[ 9.642682] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 9.642684] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 9.652831] ehci_hcd 0000:00:02.1: port 6 high speed
[ 9.652836] ehci_hcd 0000:00:02.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
[ 9.662780] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[ 9.695829] ohci_hcd 0000:00:02.0: created debug files
[ 9.695835] ohci_hcd 0000:00:02.0: irq 22, io mem 0xd9ce0000
[ 9.717165] usb 1-6: uevent
[ 9.726877] usb 1-6: usb_probe_device
[ 9.726971] usb 1-6: configuration #1 chosen from 1 choice
[ 9.734881] usb 1-6: adding 1-6:1.0 (config #1, interface 0)
[ 9.734890] usb 1-6:1.0: uevent
[ 9.734947] hub 1-6:1.0: usb_probe_interface
[ 9.734949] hub 1-6:1.0: usb_probe_interface - got id
[ 9.734951] hub 1-6:1.0: USB hub found
[ 9.755882] hub 1-6:1.0: 4 ports detected
[ 9.778237] hub 1-6:1.0: standalone hub
[ 9.778239] hub 1-6:1.0: individual port power switching
[ 9.778241] hub 1-6:1.0: individual port over-current protection
[ 9.779662] ohci_hcd 0000:00:02.0: OHCI controller state
[ 9.779665] ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers
[ 9.779667] ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3
[ 9.779670] ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0
[ 9.779672] ohci_hcd 0000:00:02.0: intrstatus 0x00000004 SF
[ 9.779674] ohci_hcd 0000:00:02.0: intrenable 0x8000004a MIE RHSC RD WDH
[ 9.779677] ohci_hcd 0000:00:02.0: hcca frame #0003
[ 9.779680] ohci_hcd 0000:00:02.0: roothub.a 0100120a POTPGT=1 NOCP NPS NDP=10(10)
[ 9.779683] ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000
[ 9.779685] ohci_hcd 0000:00:02.0: roothub.status 00008000 DRWE
[ 9.779688] ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00000100 PPS
[ 9.779691] ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS
[ 9.779693] ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00000100 PPS
[ 9.779696] ohci_hcd 0000:00:02.0: roothub.portstatus [3] 0x00000100 PPS
[ 9.779698] ohci_hcd 0000:00:02.0: roothub.portstatus [4] 0x00000100 PPS
[ 9.779701] ohci_hcd 0000:00:02.0: roothub.portstatus [5] 0x00000100 PPS
[ 9.779703] ohci_hcd 0000:00:02.0: roothub.portstatus [6] 0x00000100 PPS
[ 9.779706] ohci_hcd 0000:00:02.0: roothub.portstatus [7] 0x00000100 PPS
[ 9.779709] ohci_hcd 0000:00:02.0: roothub.portstatus [8] 0x00000100 PPS
[ 9.779711] ohci_hcd 0000:00:02.0: roothub.portstatus [9] 0x00000100 PPS
[ 9.779719] usb usb2: default language 0x0409
[ 9.779735] usb usb2: uevent
[ 9.779735] hub 1-6:1.0: TT per port
[ 9.779738] hub 1-6:1.0: TT requires at most 8 FS bit times (666 ns)
[ 9.779740] hub 1-6:1.0: Port indicators are supported
[ 9.779742] hub 1-6:1.0: power on to power good time: 100ms
[ 9.779819] usb usb2: usb_probe_device
[ 9.779897] usb usb2: configuration #1 chosen from 1 choice
[ 9.780000] hub 1-6:1.0: local power source is good
[ 9.780003] hub 1-6:1.0: enabling power on all ports
[ 9.810776] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 9.810786] usb 2-0:1.0: uevent
[ 9.810836] hub 2-0:1.0: usb_probe_interface
[ 9.810838] hub 2-0:1.0: usb_probe_interface - got id
[ 9.810840] hub 2-0:1.0: USB hub found
[ 9.832798] hub 2-0:1.0: 10 ports detected
[ 9.855792] hub 2-0:1.0: standalone hub
[ 9.855793] hub 2-0:1.0: no power switching (usb 1.0)
[ 9.855794] hub 2-0:1.0: no over-current protection
[ 9.855796] hub 2-0:1.0: power on to power good time: 2ms
[ 9.855799] hub 2-0:1.0: local power source is good
[ 9.855801] hub 2-0:1.0: trying to enable port power on non-switchable hub
[ 9.881674] usb 1-6: link qh256-0001/ffff81007f802140 start 255 [1/0 us]
[ 9.881685] usb 1-6: New USB device found, idVendor=04b4, idProduct=6560
[ 9.919407] usb 1-6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 9.959429] hub 1-6:1.0: state 7 ports 4 chg 0000 evt 0000
[ 9.960235] hub 2-0:1.0: state 7 ports 10 chg 0000 evt 0000
[ 9.960235] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 9.998292] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.030452] usb usb2: Product: OHCI Host Controller
[ 10.057298] usb usb2: Manufacturer: Linux 2.6.25 ohci_hcd
[ 10.088307] usb usb2: SerialNumber: 0000:00:02.0
[ 10.115362] USB Universal Host Controller Interface driver v3.0
[ 10.148925] ACPI: PCI Interrupt Link [LNKX] enabled at IRQ 17
[ 10.181312] ACPI: PCI Interrupt 0000:01:04.4[B] -> Link [LNKX] -> GSI 17 (level, high) -> IRQ 17
[ 10.221424] uhci_hcd 0000:01:04.4: UHCI Host Controller
[ 10.251423] uhci_hcd 0000:01:04.4: new USB bus registered, assigned bus number 3
[ 10.294454] uhci_hcd 0000:01:04.4: detected 8 ports
[ 10.321291] uhci_hcd 0000:01:04.4: port count misdetected? forcing to 2 ports
[ 10.362287] uhci_hcd 0000:01:04.4: uhci_check_and_reset_hc: cmd = 0x0000
[ 10.362289] uhci_hcd 0000:01:04.4: Performing full reset
[ 10.362297] uhci_hcd 0000:01:04.4: HCRESET not completed yet!
[ 10.381555] uhci_hcd 0000:01:04.4: irq 17, io base 0x00001800
[ 10.414353] usb usb3: default language 0x0409
[ 10.414367] usb usb3: uevent
[ 10.414414] usb usb3: usb_probe_device
[ 10.414494] usb usb3: configuration #1 chosen from 1 choice
[ 10.446292] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[ 10.446302] usb 3-0:1.0: uevent
[ 10.446348] hub 3-0:1.0: usb_probe_interface
[ 10.446349] hub 3-0:1.0: usb_probe_interface - got id
[ 10.446351] hub 3-0:1.0: USB hub found
[ 10.468282] hub 3-0:1.0: 2 ports detected
[ 10.490342] hub 3-0:1.0: standalone hub
[ 10.490344] hub 3-0:1.0: no power switching (usb 1.0)
[ 10.490345] hub 3-0:1.0: individual port over-current protection
[ 10.490347] hub 3-0:1.0: power on to power good time: 2ms
[ 10.490350] hub 3-0:1.0: local power source is good
[ 10.490352] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 10.590194] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 10.590424] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 10.590424] uhci_hcd 0000:01:04.4: port 1 portsc 0083,00
[ 10.590432] hub 3-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
[ 10.628546] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.670675] usb usb3: Product: UHCI Host Controller
[ 10.694773] hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
[ 10.697498] usb usb3: Manufacturer: Linux 2.6.25 uhci_hcd
[ 10.728533] usb usb3: SerialNumber: 0000:01:04.4
[ 10.796334] usb 3-1: new full speed USB device using uhci_hcd and address 2
[ 10.961946] usb 3-1: skipped 1 descriptor after interface
[ 10.961948] usb 3-1: skipped 1 descriptor after interface
[ 10.965184] usb 3-1: default language 0x0409
[ 10.971680] usb 3-1: uevent
[ 10.971739] usb 3-1: usb_probe_device
[ 10.971830] usb 3-1: configuration #1 chosen from 1 choice
[ 10.995165] usb 3-1: adding 3-1:1.0 (config #1, interface 0)
[ 10.995175] usb 3-1:1.0: uevent
[ 10.998525] usb 3-1: adding 3-1:1.1 (config #1, interface 1)
[ 10.998534] usb 3-1:1.1: uevent
[ 11.001734] usb 3-1: New USB device found, idVendor=03f0, idProduct=1027
[ 11.031285] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 11.071040] usb 3-1: Product: Virtual Keyboard
[ 11.095214] usb 3-1: Manufacturer: HP
[ 11.113327] uhci_hcd 0000:01:04.4: port 2 portsc 0083,00
[ 11.113332] hub 3-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
[ 11.211491] ohci_hcd 0000:00:02.0: auto-stop root hub
[ 11.216886] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
[ 11.318873] usb 3-2: new full speed USB device using uhci_hcd and address 3
[ 11.401868] uhci_hcd 0000:01:04.4: port 2 portsc 0083,00
[ 11.401877] hub 3-0:1.0: unable to enumerate USB device on port 2
[ 11.415960] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 11.415960] usbcore: registered new interface driver usblp
[ 11.446985] Initializing USB Mass Storage driver...
[ 11.474089] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004
[ 11.474096] uhci_hcd 0000:01:04.4: port 2 portsc 0083,00
[ 11.474101] hub 3-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
[ 11.474101] usbcore: registered new interface driver usb-storage
[ 11.509030] USB Mass Storage support registered.
[ 11.578421] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
[ 11.680410] usb 3-2: new full speed USB device using uhci_hcd and address 4
[ 11.849956] usb 3-2: default language 0x0409
[ 11.856448] usb 3-2: uevent
[ 11.856504] usb 3-2: usb_probe_device
[ 11.856588] usb 3-2: configuration #1 chosen from 1 choice
[ 11.869108] usb 3-2: adding 3-2:1.0 (config #1, interface 0)
[ 11.869118] usb 3-2:1.0: uevent
[ 11.869177] hub 3-2:1.0: usb_probe_interface
[ 11.869179] hub 3-2:1.0: usb_probe_interface - got id
[ 11.869180] hub 3-2:1.0: USB hub found
[ 11.889941] hub 3-2:1.0: 7 ports detected
[ 11.912733] hub 3-2:1.0: standalone hub
[ 11.912734] hub 3-2:1.0: ganged power switching
[ 11.912736] hub 3-2:1.0: individual port over-current protection
[ 11.912738] hub 3-2:1.0: power on to power good time: 100ms
[ 11.916892] hub 3-2:1.0: local power source is good
[ 11.916894] hub 3-2:1.0: enabling power on all ports
[ 12.032289] uhci_hcd 0000:01:04.4: reserve dev 4 ep81-INT, period 128, phase 0, 12 us
[ 12.035577] usb 3-2: New USB device found, idVendor=03f0, idProduct=1327
[ 12.073548] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 12.103747] usb 3-2: Product: Virtual Hub
[ 12.125541] usb 3-2: Manufacturer: HP
[ 12.139220] hub 3-2:1.0: state 7 ports 7 chg 0000 evt 0000
[ 12.154877] usb 3-2: remote wakeup needed for autosuspend
[ 12.154877] usbcore: registered new interface driver libusual
[ 12.187100] PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
[ 12.195222] hub 1-6:1.0: hub_suspend
[ 12.195227] usb 1-6: unlink qh256-0001/ffff81007f802140 start 255 [1/0 us]
[ 12.195436] usb 1-6: usb auto-suspend
[ 12.206218] hub 2-0:1.0: hub_suspend
[ 12.206222] usb usb2: bus auto-suspend
[ 12.206225] ohci_hcd 0000:00:02.0: suspend root hub
[ 12.231753] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 12.260053] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 12.293267] mice: PS/2 mouse device common for all mice
[ 12.393237] rtc_cmos 00:0a: rtc core: registered rtc_cmos as rtc0
[ 12.426885] rtc0: alarms up to one year, y3k
[ 12.458019] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@xxxxxxxxxx
[ 12.507113] cpuidle: using governor ladder
[ 12.511303] cpuidle: using governor menu
[ 12.533768] usbcore: registered new interface driver hiddev
[ 12.565765] usbhid 3-1:1.0: usb_probe_interface
[ 12.565767] usbhid 3-1:1.0: usb_probe_interface - got id
[ 12.571399] input: HP Virtual Keyboard as /devices/pci0000:00/0000:00:09.0/0000:01:04.4/usb3/3-1/3-1:1.0/input/input2
[ 12.616887] uhci_hcd 0000:01:04.4: reserve dev 2 ep81-INT, period 8, phase 4, 17 us
[ 12.620001] input,hidraw0: USB HID v1.01 Keyboard [HP Virtual Keyboard] on usb-0000:01:04.4-1
[ 12.630755] usbhid 3-1:1.1: usb_probe_interface
[ 12.630757] usbhid 3-1:1.1: usb_probe_interface - got id
[ 12.635969] input: HP Virtual Keyboard as /devices/pci0000:00/0000:00:09.0/0000:01:04.4/usb3/3-1/3-1:1.1/input/input3
[ 12.683986] input,hidraw1: USB HID v1.01 Mouse [HP Virtual Keyboard] on usb-0000:01:04.4-1
[ 12.708442] usbcore: registered new interface driver usbhid
[ 12.718396] usbhid: v2.6:USB HID core driver
[ 12.730735] Advanced Linux Sound Architecture Driver Version 1.0.16.
[ 12.767567] ALSA device list:
[ 12.783209] No soundcards found.
[ 12.796002] Netfilter messages via NETLINK v0.30.
[ 12.818719] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 12.854350] ctnetlink v0.93: registering with nfnetlink.
[ 12.886023] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.896166] TCP cubic registered
[ 12.907754] Initializing XFRM netlink socket
[ 12.933087] NET: Registered protocol family 10
[ 12.949187] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.980414] IPv6 over IPv4 tunneling driver
[ 13.005315] NET: Registered protocol family 17
[ 13.032151] RPC: Registered udp transport module.
[ 13.057597] RPC: Registered tcp transport module.
[ 13.086872] registered taskstats version 1
[ 13.111519] Magic number: 1:878:480
[ 13.131798] Freeing unused kernel memory: 404k freed
[ 13.161489] Write protecting the kernel read-only data: 6388k
[ 13.205623] blacklist used greatest stack depth: 5960 bytes left
[ 13.272433] usb usb2: uevent
[ 13.272459] usb 2-0:1.0: uevent
[ 13.272549] usb usb1: uevent
[ 13.272565] usb 1-0:1.0: uevent
[ 13.272596] usb 1-6: uevent
[ 13.272613] usb 1-6:1.0: uevent
[ 13.272915] usb usb3: uevent
[ 13.272932] usb 3-0:1.0: uevent
[ 13.272966] usb 3-1: uevent
[ 13.272983] usb 3-1:1.0: uevent
[ 13.273071] usb 3-1:1.1: uevent
[ 13.273191] usb 3-2: uevent
[ 13.273209] usb 3-2:1.0: uevent
[ 13.439005] cdrom_id used greatest stack depth: 5752 bytes left
[ 13.439005] Fusion MPT base driver 3.04.06
[ 13.457302] Copyright (c) 1999-2007 LSI Corporation
[ 13.490146] Fusion MPT SAS Host driver 3.04.06
[ 13.551998] ACPI: PCI Interrupt 0000:42:01.0[A] -> GSI 24 (level, low) -> IRQ 24
[ 13.578063] mptbase: ioc0: Initiating bringup
[ 13.880672] ioc0: LSISAS1068 B0: Capabilities={Initiator}
[ 13.891967] mptbase: ioc0: PCI-MSI enabled
[ 14.221645] hub 1-0:1.0: hub_suspend
[ 14.221658] usb usb1: bus auto-suspend
[ 14.221661] ehci_hcd 0000:00:02.1: suspend root hub
[ 37.116157] scsi2 : ioc0: LSISAS1068 B0, FwRev=01142100h, Ports=1, MaxQ=511, IRQ=2296
[ 37.192228] scsi 2:0:0:0: Direct-Access HP DG036A9BB6 HPD0 PQ: 0 ANSI: 5
[ 37.240348] sd 2:0:0:0: [sda] 71132960 512-byte hardware sectors (36420 MB)
[ 37.281548] sd 2:0:0:0: [sda] Write Protect is off
[ 37.308076] sd 2:0:0:0: [sda] Mode Sense: cf 00 10 08
[ 37.309193] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 37.358843] sd 2:0:0:0: [sda] 71132960 512-byte hardware sectors (36420 MB)
[ 37.390584] sd 2:0:0:0: [sda] Write Protect is off
[ 37.417070] sd 2:0:0:0: [sda] Mode Sense: cf 00 10 08
[ 37.418192] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 37.467355] sda: unknown partition table
[ 37.498571] sd 2:0:0:0: [sda] Attached SCSI disk
[ 37.515091] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 37.547004] scsi 2:0:1:0: Direct-Access HP DG036A9BB6 HPD0 PQ: 0 ANSI: 5
[ 37.563238] sd 2:0:1:0: [sdb] 71132960 512-byte hardware sectors (36420 MB)
[ 37.603658] sd 2:0:1:0: [sdb] Write Protect is off
[ 37.606247] sd 2:0:1:0: [sdb] Mode Sense: cf 00 10 08
[ 37.607792] sd 2:0:1:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 37.657320] sd 2:0:1:0: [sdb] 71132960 512-byte hardware sectors (36420 MB)
[ 37.698053] sd 2:0:1:0: [sdb] Write Protect is off
[ 37.719056] sd 2:0:1:0: [sdb] Mode Sense: cf 00 10 08
[ 37.720179] sd 2:0:1:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 37.769658] sdb: unknown partition table
[ 37.796433] sd 2:0:1:0: [sdb] Attached SCSI disk
[ 37.812559] sd 2:0:1:0: Attached scsi generic sg2 type 0
[ 37.845644] scsi 2:0:2:0: Direct-Access HP DG036A9BB6 HPD0 PQ: 0 ANSI: 5
[ 37.892862] sd 2:0:2:0: [sdc] 71132960 512-byte hardware sectors (36420 MB)
[ 37.933268] sd 2:0:2:0: [sdc] Write Protect is off
[ 37.960364] sd 2:0:2:0: [sdc] Mode Sense: cf 00 10 08
[ 37.961772] sd 2:0:2:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 38.002426] sd 2:0:2:0: [sdc] 71132960 512-byte hardware sectors (36420 MB)
[ 38.034287] sd 2:0:2:0: [sdc] Write Protect is off
[ 38.061673] sd 2:0:2:0: [sdc] Mode Sense: cf 00 10 08
[ 38.062802] sd 2:0:2:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 38.111810] sdc: unknown partition table
[ 38.143735] sd 2:0:2:0: [sdc] Attached SCSI disk
[ 38.170949] sd 2:0:2:0: Attached scsi generic sg3 type 0
[ 38.193002] scsi 2:0:3:0: Direct-Access HP DG036A9BB6 HPD0 PQ: 0 ANSI: 5
[ 38.241046] sd 2:0:3:0: [sdd] 71132960 512-byte hardware sectors (36420 MB)
[ 38.281113] sd 2:0:3:0: [sdd] Write Protect is off
[ 38.308612] sd 2:0:3:0: [sdd] Mode Sense: cf 00 10 08
[ 38.310061] sd 2:0:3:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 38.359811] sd 2:0:3:0: [sdd] 71132960 512-byte hardware sectors (36420 MB)
[ 38.400494] sd 2:0:3:0: [sdd] Write Protect is off
[ 38.427897] sd 2:0:3:0: [sdd] Mode Sense: cf 00 10 08
[ 38.429016] sd 2:0:3:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 38.470830] sdd: unknown partition table
[ 38.504217] sd 2:0:3:0: [sdd] Attached SCSI disk
[ 38.521865] sd 2:0:3:0: Attached scsi generic sg4 type 0
[ 38.548118] scsi 2:0:4:0: Direct-Access HP DG072A8B54 HPD7 PQ: 0 ANSI: 5
[ 38.584811] sd 2:0:4:0: [sde] 143374738 512-byte hardware sectors (73408 MB)
[ 38.624570] sd 2:0:4:0: [sde] Write Protect is off
[ 38.651330] sd 2:0:4:0: [sde] Mode Sense: db 00 10 08
[ 38.652911] sd 2:0:4:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 38.692371] sd 2:0:4:0: [sde] 143374738 512-byte hardware sectors (73408 MB)
[ 38.723877] sd 2:0:4:0: [sde] Write Protect is off
[ 38.750671] sd 2:0:4:0: [sde] Mode Sense: db 00 10 08
[ 38.752304] sd 2:0:4:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 38.801145] sde: unknown partition table
[ 38.826062] sd 2:0:4:0: [sde] Attached SCSI disk
[ 38.853042] sd 2:0:4:0: Attached scsi generic sg5 type 0
[ 38.884752] scsi 2:0:5:0: Direct-Access HP DG072A8B54 HPD7 PQ: 0 ANSI: 5
[ 38.932258] sd 2:0:5:0: [sdf] 143374738 512-byte hardware sectors (73408 MB)
[ 38.952473] sd 2:0:5:0: [sdf] Write Protect is off
[ 38.979207] sd 2:0:5:0: [sdf] Mode Sense: db 00 10 08
[ 38.980801] sd 2:0:5:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 39.030235] sd 2:0:5:0: [sdf] 143374738 512-byte hardware sectors (73408 MB)
[ 39.066378] sd 2:0:5:0: [sdf] Write Protect is off
[ 39.093536] sd 2:0:5:0: [sdf] Mode Sense: db 00 10 08
[ 39.094819] sd 2:0:5:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 39.143703] sdf: sdf1 sdf2 < sdf5 >
[ 39.179850] sd 2:0:5:0: [sdf] Attached SCSI disk
[ 39.205591] sd 2:0:5:0: Attached scsi generic sg6 type 0
[ 39.217358] scsi 2:0:6:0: Direct-Access HP DG072A8B54 HPD7 PQ: 0 ANSI: 5
[ 39.264821] sd 2:0:6:0: [sdg] 143374738 512-byte hardware sectors (73408 MB)
[ 39.305985] sd 2:0:6:0: [sdg] Write Protect is off
[ 39.332757] sd 2:0:6:0: [sdg] Mode Sense: db 00 10 08
[ 39.334373] sd 2:0:6:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 39.383811] sd 2:0:6:0: [sdg] 143374738 512-byte hardware sectors (73408 MB)
[ 39.415310] sd 2:0:6:0: [sdg] Write Protect is off
[ 39.442123] sd 2:0:6:0: [sdg] Mode Sense: db 00 10 08
[ 39.443405] sd 2:0:6:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 39.492261] sdg: unknown partition table
[ 39.514245] sd 2:0:6:0: [sdg] Attached SCSI disk
[ 39.541132] sd 2:0:6:0: Attached scsi generic sg7 type 0
[ 39.573641] scsi 2:0:7:0: Direct-Access HP DG072A8B54 HPD7 PQ: 0 ANSI: 5
[ 39.622449] sd 2:0:7:0: [sdh] 143374738 512-byte hardware sectors (73408 MB)
[ 39.642322] sd 2:0:7:0: [sdh] Write Protect is off
[ 39.669452] sd 2:0:7:0: [sdh] Mode Sense: db 00 10 08
[ 39.671453] sd 2:0:7:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 39.702515] sd 2:0:7:0: [sdh] 143374738 512-byte hardware sectors (73408 MB)
[ 39.723055] sd 2:0:7:0: [sdh] Write Protect is off
[ 39.749792] sd 2:0:7:0: [sdh] Mode Sense: db 00 10 08
[ 39.751424] sd 2:0:7:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 39.800335] sdh: sdh1
[ 39.815333] sd 2:0:7:0: [sdh] Attached SCSI disk
[ 39.841218] sd 2:0:7:0: Attached scsi generic sg8 type 0
[ 39.873299] modprobe used greatest stack depth: 3336 bytes left
[ 40.083342] kjournald starting. Commit interval 5 seconds
[ 40.083342] EXT3-fs: mounted filesystem with ordered data mode.
[ 41.015076] udevd version 125 started
[ 41.139110] usb usb2: uevent
[ 41.139131] usb 2-0:1.0: uevent
[ 41.139227] usb usb1: uevent
[ 41.139245] usb 1-0:1.0: uevent
[ 41.139276] usb 1-6: uevent
[ 41.139293] usb 1-6:1.0: uevent
[ 41.139605] usb usb3: uevent
[ 41.139623] usb 3-0:1.0: uevent
[ 41.139657] usb 3-1: uevent
[ 41.139676] usb 3-1:1.0: uevent
[ 41.139766] usb 3-1:1.1: uevent
[ 41.139893] usb 3-2: uevent
[ 41.139917] usb 3-2:1.0: uevent
[ 42.693342] Adding 2963952k swap on /dev/sdf5. Priority:-1 extents:1 across:2963952k
[ 43.025504] EXT3 FS on sdf1, internal journal
[ 44.935689] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 48.073373] bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex
[ 48.113743] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 58.545280] eth0: no IPv6 routers present
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.25 (dannf@dl585g2) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #67 SMP Thu Jul 9 12:11:29 MDT 2009
[ 0.000000] Command line: root=/dev/disk/by-id/scsi-35000c50000d5ca0f-part1 ro console=tty1 console=ttyS1,115200
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e400 (usable)
[ 0.000000] BIOS-e820: 000000000009e400 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fd4e000 (usable)
[ 0.000000] BIOS-e820: 000000007fd4e000 - 000000007fd56000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007fd56000 - 000000007fd57000 (usable)
[ 0.000000] BIOS-e820: 000000007fd57000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fed00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffc00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 000000047ffff000 (usable)
[ 0.000000] Entering add_active_range(0, 0, 158) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 523598) 1 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 523606, 523607) 2 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 1048576, 4718591) 3 entries of 3200 used
[ 0.000000] max_pfn_mapped = 4718591
[ 0.000000] x86: PAT support disabled.
[ 0.000000] init_memory_mapping
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI: RSDP 000F4F00, 0024 (r2 HP )
[ 0.000000] ACPI: XSDT 7FD4ED80, 0074 (r1 HP ProLiant 2 Ò 162E)
[ 0.000000] ACPI: FACP 7FD4EE00, 00F4 (r3 HP A07 2 Ò 162E)
[ 0.000000] ACPI: DSDT 7FD4EF00, 4A59 (r1 HP DSDT 1 INTL 20030228)
[ 0.000000] ACPI: FACS 7FD4E100, 0040
[ 0.000000] ACPI: SPCR 7FD4E140, 0050 (r1 HP SPCRRBSU 1 Ò 162E)
[ 0.000000] ACPI: HPET 7FD4E1C0, 0038 (r1 HP ProLiant 2 Ò 162E)
[ 0.000000] ACPI: SPMI 7FD4E200, 0040 (r5 HP ProLiant 1 Ò 162E)
[ 0.000000] ACPI: ERST 7FD4E240, 01D0 (r1 HP ProLiant 1 Ò 162E)
[ 0.000000] ACPI: APIC 7FD4E440, 00C6 (r1 HP ProLiant 2 0)
[ 0.000000] ACPI: SRAT 7FD4E600, 01A0 (r1 AMD FAM_F_10 2 AMD 1)
[ 0.000000] ACPI: FFFF 7FD4EA00, 0176 (r1 HP ProLiant 1 Ò 162E)
[ 0.000000] ACPI: BERT 7FD4EB80, 0030 (r1 HP ProLiant 1 Ò 162E)
[ 0.000000] ACPI: HEST 7FD4EBC0, 0170 (r1 HP ProLiant 1 Ò 162E)
[ 0.000000] SRAT: PXM 0 -> APIC 0 -> Node 0
[ 0.000000] SRAT: PXM 0 -> APIC 1 -> Node 0
[ 0.000000] SRAT: PXM 1 -> APIC 2 -> Node 1
[ 0.000000] SRAT: PXM 1 -> APIC 3 -> Node 1
[ 0.000000] SRAT: PXM 2 -> APIC 4 -> Node 2
[ 0.000000] SRAT: PXM 2 -> APIC 5 -> Node 2
[ 0.000000] SRAT: PXM 3 -> APIC 6 -> Node 3
[ 0.000000] SRAT: PXM 3 -> APIC 7 -> Node 3
[ 0.000000] SRAT: Node 0 PXM 0 0-a0000
[ 0.000000] Entering add_active_range(0, 0, 158) 0 entries of 3200 used
[ 0.000000] SRAT: Node 0 PXM 0 100000-80000000
[ 0.000000] Entering add_active_range(0, 256, 523598) 1 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 523606, 523607) 2 entries of 3200 used
[ 0.000000] SRAT: Node 0 PXM 0 100000000-180000000
[ 0.000000] Entering add_active_range(0, 1048576, 1572864) 3 entries of 3200 used
[ 0.000000] SRAT: Node 1 PXM 1 180000000-280000000
[ 0.000000] Entering add_active_range(1, 1572864, 2621440) 4 entries of 3200 used
[ 0.000000] SRAT: Node 2 PXM 2 280000000-380000000
[ 0.000000] Entering add_active_range(2, 2621440, 3670016) 5 entries of 3200 used
[ 0.000000] SRAT: Node 3 PXM 3 380000000-480000000
[ 0.000000] Entering add_active_range(3, 3670016, 4718591) 6 entries of 3200 used
[ 0.000000] NUMA: Allocated memnodemap from 1a000 - 23080
[ 0.000000] NUMA: Using 20 for the hash shift.
[ 0.000000] Bootmem setup node 0 0000000000000000-0000000180000000
[ 0.000000] NODE_DATA [0000000000023080 - 000000000002b07f]
[ 0.000000] bootmap [000000000002c000 - 000000000005bfff] pages 30
[ 0.000000] early res: 0 [0-fff] BIOS data page
[ 0.000000] early res: 1 [6000-7fff] TRAMPOLINE
[ 0.000000] early res: 2 [200000-a8a97b] TEXT DATA BSS
[ 0.000000] early res: 3 [37d54000-37fef2ed] RAMDISK
[ 0.000000] early res: 4 [9e400-fffff] BIOS reserved
[ 0.000000] early res: 5 [8000-19fff] PGTABLE
[ 0.000000] early res: 6 [1a000-2307f] MEMNODEMAP
[ 0.000000] Bootmem setup node 1 0000000180000000-0000000280000000
[ 0.000000] NODE_DATA [0000000180000000 - 0000000180007fff]
[ 0.000000] bootmap [0000000180008000 - 0000000180027fff] pages 20
[ 0.000000] Bootmem setup node 2 0000000280000000-0000000380000000
[ 0.000000] NODE_DATA [0000000280000000 - 0000000280007fff]
[ 0.000000] bootmap [0000000280008000 - 0000000280027fff] pages 20
[ 0.000000] Bootmem setup node 3 0000000380000000-000000047ffff000
[ 0.000000] NODE_DATA [0000000380000000 - 0000000380007fff]
[ 0.000000] bootmap [0000000380008000 - 0000000380027fff] pages 20
[ 0.000000] [ffffe20000000000-ffffe200049fffff] PMD -> [ffff810001200000-ffff810003ffffff] on node 0
[ 0.000000] [ffffe20004a00000-ffffe200053fffff] PMD -> [ffff81000c000000-ffff81000c9fffff] on node 0
[ 0.000000] [ffffe20005400000-ffffe20008bfffff] PMD -> [ffff810180200000-ffff8101839fffff] on node 1
[ 0.000000] [ffffe20008c00000-ffffe2000c3fffff] PMD -> [ffff810280200000-ffff8102839fffff] on node 2
[ 0.000000] [ffffe2000c400000-ffffe2000fbfffff] PMD -> [ffff810380200000-ffff8103839fffff] on node 3
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 4718591
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[7] active PFN ranges
[ 0.000000] 0: 0 -> 158
[ 0.000000] 0: 256 -> 523598
[ 0.000000] 0: 523606 -> 523607
[ 0.000000] 0: 1048576 -> 1572864
[ 0.000000] 1: 1572864 -> 2621440
[ 0.000000] 2: 2621440 -> 3670016
[ 0.000000] 3: 3670016 -> 4718591
[ 0.000000] On node 0 totalpages: 1047789
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 2315 pages reserved
[ 0.000000] DMA zone: 1627 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 505223 pages, LIFO batch:31
[ 0.000000] Normal zone: 7168 pages used for memmap
[ 0.000000] Normal zone: 517120 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] On node 1 totalpages: 1048576
[ 0.000000] DMA zone: 0 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages used for memmap
[ 0.000000] Normal zone: 14336 pages used for memmap
[ 0.000000] Normal zone: 1034240 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] On node 2 totalpages: 1048576
[ 0.000000] DMA zone: 0 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages used for memmap
[ 0.000000] Normal zone: 14336 pages used for memmap
[ 0.000000] Normal zone: 1034240 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] On node 3 totalpages: 1048575
[ 0.000000] DMA zone: 0 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages used for memmap
[ 0.000000] Normal zone: 14335 pages used for memmap
[ 0.000000] Normal zone: 1034240 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] ACPI: PM-Timer IO Port: 0x908
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xd9cf0000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 0, address 0xd9cf0000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x09] address[0xd9fd0000] gsi_base[24])
[ 0.000000] IOAPIC[1]: apic_id 9, version 0, address 0xd9fd0000, GSI 24-30
[ 0.000000] ACPI: IOAPIC (id[0x0a] address[0xd9fe0000] gsi_base[31])
[ 0.000000] IOAPIC[2]: apic_id 10, version 0, address 0xd9fe0000, GSI 31-37
[ 0.000000] ACPI: IOAPIC (id[0x0b] address[0xd9ff0000] gsi_base[38])
[ 0.000000] IOAPIC[3]: apic_id 11, version 0, address 0xd9ff0000, GSI 38-61
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: NMI_SRC (dfl dfl global_irq 28)
[ 0.000000] ACPI: NMI_SRC (dfl dfl global_irq 35)
[ 0.000000] Setting APIC routing to flat
[ 0.000000] ACPI: HPET id: 0x10228201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007fd4e000 - 000000007fd56000
[ 0.000000] PM: Registered nosave memory: 000000007fd57000 - 0000000080000000
[ 0.000000] PM: Registered nosave memory: 0000000080000000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
[ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fed00000
[ 0.000000] PM: Registered nosave memory: 00000000fed00000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee10000
[ 0.000000] PM: Registered nosave memory: 00000000fee10000 - 00000000ffc00000
[ 0.000000] PM: Registered nosave memory: 00000000ffc00000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
[ 0.000000] SMP: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 44480 bytes of per cpu data
[ 0.000000] NR_CPUS: 64, nr_cpu_ids: 8
[ 0.000000] Built 4 zonelists in Zone order, mobility grouping on. Total pages: 4126690
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: root=/dev/disk/by-id/scsi-35000c50000d5ca0f-part1 ro console=tty1 console=ttyS1,115200
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] TSC calibrated against PM_TIMER
[ 0.000001] Marking TSC unstable due to TSCs unsynchronized
[ 0.000003] time.c: Detected 2612.040 MHz processor.
[ 0.000011] spurious 8259A interrupt: IRQ7.
[ 0.000999] Console: colour VGA+ 80x25
[ 0.000999] console [tty1] enabled
[ 0.000999] console [ttyS1] enabled
[ 0.000999] Checking aperture...
[ 0.000999] Node 0: aperture @ 4000000 size 32 MB
[ 0.000999] Aperture pointing to e820 RAM. Ignoring.
[ 0.000999] No AGP bridge found
[ 0.000999] Your BIOS doesn't leave a aperture memory hole
[ 0.000999] Please enable the IOMMU option in the BIOS setup
[ 0.000999] This costs you 64 MB of RAM
[ 0.000999] Mapping aperture over 65536 KB of RAM @ 4000000
[ 0.000999] PM: Registered nosave memory: 0000000004000000 - 0000000008000000
[ 0.000999] Memory: 16466516k/18874364k available (4337k kernel code, 307548k reserved, 2815k data, 408k init)
[ 0.000999] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.000999] SLUB: Genslabs=13, HWalign=64, Order=0-1, MinObjects=4, CPUs=8, Nodes=4
[ 0.000999] hpet clockevent registered
[ 0.059992] Calibrating delay using timer specific routine.. 5226.24 BogoMIPS (lpj=2613121)
[ 0.061048] Security Framework initialized
[ 0.061995] SELinux: Initializing.
[ 0.063003] SELinux: Starting in permissive mode
[ 0.063011] selinux_register_security: Registering secondary module capability
[ 0.063991] Capability LSM initialized as secondary
[ 0.067041] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.081003] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.087903] Mount-cache hash table entries: 256
[ 0.088238] Initializing cgroup subsys ns
[ 0.088611] Initializing cgroup subsys cpuacct
[ 0.089011] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.089988] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.090988] CPU 0/0 -> Node 0
[ 0.091995] CPU: Physical Processor ID: 0
[ 0.092987] CPU: Processor Core ID: 0
[ 0.094002] ACPI: Core revision 20070126
[ 0.114232] CPU0: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.116983] Using local APIC timer interrupts.
[ 0.118982] APIC timer calibration result 12557873
[ 0.118984] Detected 12.557 MHz APIC timer.
[ 0.120112] Booting processor 1/2 ip 6000
[ 0.120112] Initializing CPU#1
[ 0.120112] Calibrating delay using timer specific routine.. 5223.83 BogoMIPS (lpj=2611917)
[ 0.120112] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.120112] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.120112] CPU 1/2 -> Node 1
[ 0.120112] CPU: Physical Processor ID: 1
[ 0.120112] CPU: Processor Core ID: 0
[ 0.120112] x86: PAT support disabled.
[ 0.192316] CPU1: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.195051] Booting processor 2/4 ip 6000
[ 0.195051] Initializing CPU#2
[ 0.195051] Calibrating delay using timer specific routine.. 5223.89 BogoMIPS (lpj=2611947)
[ 0.195051] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.195051] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.195051] CPU 2/4 -> Node 2
[ 0.195051] CPU: Physical Processor ID: 2
[ 0.195051] CPU: Processor Core ID: 0
[ 0.195051] x86: PAT support disabled.
[ 0.267330] CPU2: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.270040] Booting processor 3/6 ip 6000
[ 0.270040] Initializing CPU#3
[ 0.270040] Calibrating delay using timer specific routine.. 5223.89 BogoMIPS (lpj=2611949)
[ 0.270040] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.270040] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.270040] CPU 3/6 -> Node 3
[ 0.270040] CPU: Physical Processor ID: 3
[ 0.270040] CPU: Processor Core ID: 0
[ 0.270040] x86: PAT support disabled.
[ 0.342374] CPU3: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.345019] Booting processor 4/1 ip 6000
[ 0.345019] Initializing CPU#4
[ 0.345019] Calibrating delay using timer specific routine.. 5223.81 BogoMIPS (lpj=2611905)
[ 0.345019] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.345019] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.345019] CPU 4/1 -> Node 0
[ 0.345019] CPU: Physical Processor ID: 0
[ 0.345019] CPU: Processor Core ID: 1
[ 0.345019] x86: PAT support disabled.
[ 0.417284] CPU4: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.420010] Booting processor 5/3 ip 6000
[ 0.420010] Initializing CPU#5
[ 0.420010] Calibrating delay using timer specific routine.. 5223.87 BogoMIPS (lpj=2611939)
[ 0.420010] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.420010] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.420010] CPU 5/3 -> Node 1
[ 0.420010] CPU: Physical Processor ID: 1
[ 0.420010] CPU: Processor Core ID: 1
[ 0.420010] x86: PAT support disabled.
[ 0.492270] CPU5: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.494997] Booting processor 6/5 ip 6000
[ 0.494997] Initializing CPU#6
[ 0.494997] Calibrating delay using timer specific routine.. 5223.85 BogoMIPS (lpj=2611928)
[ 0.494997] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.494997] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.494997] CPU 6/5 -> Node 2
[ 0.494997] CPU: Physical Processor ID: 2
[ 0.494997] CPU: Processor Core ID: 1
[ 0.494997] x86: PAT support disabled.
[ 0.567298] CPU6: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.569991] Booting processor 7/7 ip 6000
[ 0.569991] Initializing CPU#7
[ 0.569991] Calibrating delay using timer specific routine.. 5223.84 BogoMIPS (lpj=2611923)
[ 0.569991] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.569991] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.569991] CPU 7/7 -> Node 3
[ 0.569991] CPU: Physical Processor ID: 3
[ 0.569991] CPU: Processor Core ID: 1
[ 0.569991] x86: PAT support disabled.
[ 0.642353] CPU7: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
[ 0.644908] Brought up 8 CPUs
[ 0.645904] Total of 8 processors activated (41793.25 BogoMIPS).
[ 1.067964] khelper used greatest stack depth: 6056 bytes left
[ 1.067964] net_namespace: 1176 bytes
[ 1.068097] Time: 12:14:05 Date: 07/09/09
[ 1.068141] NET: Registered protocol family 16
[ 1.154526] No dock devices found.
[ 1.155479] TOM: 0000000080000000 aka 2048M
[ 1.156318] TOM2: 0000000480000000 aka 18432M
[ 1.157317] bus: 00 to node: 00
[ 1.157318] bus: 01 to node: 00
[ 1.157320] bus: 02 to node: 00
[ 1.157321] bus: 03 to node: 00
[ 1.157322] bus: 04 to node: 00
[ 1.157323] bus: 05 to node: 00
[ 1.157324] bus: 06 to node: 00
[ 1.157325] bus: 07 to node: 00
[ 1.157326] bus: 08 to node: 00
[ 1.157327] bus: 09 to node: 00
[ 1.157328] bus: 0a to node: 00
[ 1.157330] bus: 0b to node: 00
[ 1.157331] bus: 0c to node: 00
[ 1.157332] bus: 0d to node: 00
[ 1.157333] bus: 0e to node: 00
[ 1.157334] bus: 0f to node: 00
[ 1.157335] bus: 10 to node: 00
[ 1.157336] bus: 11 to node: 00
[ 1.157337] bus: 12 to node: 00
[ 1.157338] bus: 13 to node: 00
[ 1.157340] bus: 14 to node: 00
[ 1.157341] bus: 15 to node: 00
[ 1.157342] bus: 16 to node: 00
[ 1.157343] bus: 17 to node: 00
[ 1.157344] bus: 18 to node: 00
[ 1.157345] bus: 19 to node: 00
[ 1.157346] bus: 1a to node: 00
[ 1.157347] bus: 1b to node: 00
[ 1.157349] bus: 1c to node: 00
[ 1.157350] bus: 1d to node: 00
[ 1.157351] bus: 1e to node: 00
[ 1.157352] bus: 1f to node: 00
[ 1.157353] bus: 20 to node: 00
[ 1.157354] bus: 21 to node: 00
[ 1.157355] bus: 22 to node: 00
[ 1.157356] bus: 23 to node: 00
[ 1.157358] bus: 24 to node: 00
[ 1.157359] bus: 25 to node: 00
[ 1.157360] bus: 26 to node: 00
[ 1.157361] bus: 27 to node: 00
[ 1.157362] bus: 28 to node: 00
[ 1.157363] bus: 29 to node: 00
[ 1.157364] bus: 2a to node: 00
[ 1.157365] bus: 2b to node: 00
[ 1.157366] bus: 2c to node: 00
[ 1.157368] bus: 2d to node: 00
[ 1.157369] bus: 2e to node: 00
[ 1.157370] bus: 2f to node: 00
[ 1.157371] bus: 30 to node: 00
[ 1.157372] bus: 31 to node: 00
[ 1.157373] bus: 32 to node: 00
[ 1.157374] bus: 33 to node: 00
[ 1.157375] bus: 34 to node: 00
[ 1.157376] bus: 35 to node: 00
[ 1.157378] bus: 36 to node: 00
[ 1.157379] bus: 37 to node: 00
[ 1.157380] bus: 38 to node: 00
[ 1.157381] bus: 39 to node: 00
[ 1.157382] bus: 3a to node: 00
[ 1.157383] bus: 3b to node: 00
[ 1.157384] bus: 3c to node: 00
[ 1.157385] bus: 3d to node: 00
[ 1.157386] bus: 3e to node: 00
[ 1.157388] bus: 3f to node: 00
[ 1.157389] bus: 40 to node: 01
[ 1.157390] bus: 41 to node: 01
[ 1.157391] bus: 42 to node: 01
[ 1.157392] bus: 43 to node: 01
[ 1.157393] bus: 44 to node: 01
[ 1.157394] bus: 45 to node: 01
[ 1.157395] bus: 46 to node: 01
[ 1.157397] bus: 47 to node: 01
[ 1.157398] bus: 48 to node: 01
[ 1.157399] bus: 49 to node: 01
[ 1.157400] bus: 4a to node: 01
[ 1.157401] bus: 4b to node: 01
[ 1.157402] bus: 4c to node: 01
[ 1.157403] bus: 4d to node: 01
[ 1.157404] bus: 4e to node: 01
[ 1.157405] bus: 4f to node: 01
[ 1.157406] bus: 50 to node: 01
[ 1.157408] bus: 51 to node: 01
[ 1.157409] bus: 52 to node: 01
[ 1.157410] bus: 53 to node: 01
[ 1.157411] bus: 54 to node: 01
[ 1.157412] bus: 55 to node: 01
[ 1.157413] bus: 56 to node: 01
[ 1.157414] bus: 57 to node: 01
[ 1.157415] bus: 58 to node: 01
[ 1.157416] bus: 59 to node: 01
[ 1.157418] bus: 5a to node: 01
[ 1.157419] bus: 5b to node: 01
[ 1.157420] bus: 5c to node: 01
[ 1.157421] bus: 5d to node: 01
[ 1.157422] bus: 5e to node: 01
[ 1.157423] bus: 5f to node: 01
[ 1.157424] bus: 60 to node: 01
[ 1.157425] bus: 61 to node: 01
[ 1.157427] bus: 62 to node: 01
[ 1.157428] bus: 63 to node: 01
[ 1.157429] bus: 64 to node: 01
[ 1.157430] bus: 65 to node: 01
[ 1.157431] bus: 66 to node: 01
[ 1.157432] bus: 67 to node: 01
[ 1.157433] bus: 68 to node: 01
[ 1.157434] bus: 69 to node: 01
[ 1.157435] bus: 6a to node: 01
[ 1.157436] bus: 6b to node: 01
[ 1.157438] bus: 6c to node: 01
[ 1.157439] bus: 6d to node: 01
[ 1.157440] bus: 6e to node: 01
[ 1.157441] bus: 6f to node: 01
[ 1.157442] bus: 70 to node: 01
[ 1.157443] bus: 71 to node: 01
[ 1.157444] bus: 72 to node: 01
[ 1.157445] bus: 73 to node: 01
[ 1.157446] bus: 74 to node: 01
[ 1.157448] bus: 75 to node: 01
[ 1.157449] bus: 76 to node: 01
[ 1.157450] bus: 77 to node: 01
[ 1.157451] bus: 78 to node: 01
[ 1.157452] bus: 79 to node: 01
[ 1.157453] bus: 7a to node: 01
[ 1.157454] bus: 7b to node: 01
[ 1.157455] bus: 7c to node: 01
[ 1.157457] bus: 7d to node: 01
[ 1.157458] bus: 7e to node: 01
[ 1.157459] bus: 7f to node: 01
[ 1.157461] bus: [00,3f] on node 0 link 1
[ 1.157462] bus: 00 index 0 io port: [0, 2fff]
[ 1.157464] bus: 00 index 1 mmio: [80000000, d9efffff]
[ 1.157465] bus: 00 index 2 mmio: [dff00000, e3ffffff]
[ 1.157467] bus: 00 index 3 mmio: [a0000, bffff]
[ 1.157468] bus: 00 index 4 mmio: [e8000000, ffffffff]
[ 1.157470] bus: 00 index 5 mmio: [480000000, fbffffffff]
[ 1.157472] bus: [40,7f] on node 1 link 2
[ 1.157473] bus: 40 index 0 io port: [3000, ffff]
[ 1.157475] bus: 40 index 1 mmio: [d9f00000, dfefffff]
[ 1.157476] bus: 40 index 2 mmio: [e4000000, e7ffffff]
[ 1.157501] ACPI: bus type pci registered
[ 1.158417] PCI: Using configuration type 1 for base access
[ 1.164586] ACPI: EC: Look up EC in DSDT
[ 1.167975] ACPI: SSDT 7FD58000, 09BC (r2 HP PNOWSSDT 2 HP 1)
[ 1.169901] ACPI: Interpreter enabled
[ 1.170315] ACPI: (supports S0 S4 S5)
[ 1.172314] ACPI: Using IOAPIC for interrupt routing
[ 1.180145] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 1.180375] PCI: Scanning bus 0000:00
[ 1.180393] PCI: Found 0000:00:00.0 [10de/005e] 000580 00
[ 1.180421] PCI: Found 0000:00:01.0 [10de/0051] 000601 00
[ 1.180432] pci 0000:00:01.0: calling nvidia_force_enable_hpet+0x0/0xa3()
[ 1.180451] PCI: Found 0000:00:02.0 [10de/005a] 000c03 00
[ 1.180473] PCI: Found 0000:00:02.1 [10de/005b] 000c03 00
[ 1.180499] PCI: Found 0000:00:06.0 [10de/0053] 000101 00
[ 1.180516] PCI: Found 0000:00:09.0 [10de/005c] 000604 01
[ 1.180530] PCI: Found 0000:00:0c.0 [10de/005d] 000604 01
[ 1.180545] PCI: Found 0000:00:0d.0 [10de/005d] 000604 01
[ 1.180562] PCI: Found 0000:00:0e.0 [10de/005d] 000604 01
[ 1.180584] PCI: Found 0000:00:18.0 [1022/1100] 000600 00
[ 1.180595] PCI: Found 0000:00:18.1 [1022/1101] 000600 00
[ 1.180605] PCI: Found 0000:00:18.2 [1022/1102] 000600 00
[ 1.180617] PCI: Found 0000:00:18.3 [1022/1103] 000600 00
[ 1.180632] PCI: Found 0000:00:19.0 [1022/1100] 000600 00
[ 1.180644] PCI: Found 0000:00:19.1 [1022/1101] 000600 00
[ 1.180655] PCI: Found 0000:00:19.2 [1022/1102] 000600 00
[ 1.181322] PCI: Found 0000:00:19.3 [1022/1103] 000600 00
[ 1.181337] PCI: Found 0000:00:1a.0 [1022/1100] 000600 00
[ 1.181350] PCI: Found 0000:00:1a.1 [1022/1101] 000600 00
[ 1.181361] PCI: Found 0000:00:1a.2 [1022/1102] 000600 00
[ 1.181373] PCI: Found 0000:00:1a.3 [1022/1103] 000600 00
[ 1.181390] PCI: Found 0000:00:1b.0 [1022/1100] 000600 00
[ 1.181403] PCI: Found 0000:00:1b.1 [1022/1101] 000600 00
[ 1.181415] PCI: Found 0000:00:1b.2 [1022/1102] 000600 00
[ 1.181432] PCI: Found 0000:00:1b.3 [1022/1103] 000600 00
[ 1.181445] PCI: Fixups for bus 0000:00
[ 1.181448] PCI: Scanning behind PCI bridge 0000:00:09.0, config 010100, pass 0
[ 1.181452] PCI: Scanning bus 0000:01
[ 1.181469] PCI: Found 0000:01:03.0 [1002/515e] 000300 00
[ 1.181510] PCI: Found 0000:01:04.0 [0e11/b203] 000880 00
[ 1.181552] PCI: Found 0000:01:04.2 [0e11/b204] 000880 00
[ 1.181600] PCI: Found 0000:01:04.4 [103c/3300] 000c03 00
[ 1.181646] PCI: Found 0000:01:04.6 [103c/3302] 000c07 00
[ 1.181695] PCI: Fixups for bus 0000:01
[ 1.181696] PCI: Transparent bridge - 0000:00:09.0
[ 1.182314] PCI: Bus scan for 0000:01 returning with max=01
[ 1.182317] PCI: Scanning behind PCI bridge 0000:00:0c.0, config 0a0800, pass 0
[ 1.182320] PCI: Scanning bus 0000:08
[ 1.182347] PCI: Fixups for bus 0000:08
[ 1.182351] PCI: Bus scan for 0000:08 returning with max=08
[ 1.182354] PCI: Scanning behind PCI bridge 0000:00:0d.0, config 070500, pass 0
[ 1.182359] PCI: Scanning bus 0000:05
[ 1.182386] PCI: Fixups for bus 0000:05
[ 1.182391] PCI: Bus scan for 0000:05 returning with max=05
[ 1.182393] PCI: Scanning behind PCI bridge 0000:00:0e.0, config 040200, pass 0
[ 1.182396] PCI: Scanning bus 0000:02
[ 1.182423] PCI: Fixups for bus 0000:02
[ 1.182427] PCI: Bus scan for 0000:02 returning with max=02
[ 1.182430] PCI: Scanning behind PCI bridge 0000:00:09.0, config 010100, pass 1
[ 1.182432] PCI: Scanning behind PCI bridge 0000:00:0c.0, config 0a0800, pass 1
[ 1.182435] PCI: Scanning behind PCI bridge 0000:00:0d.0, config 070500, pass 1
[ 1.182438] PCI: Scanning behind PCI bridge 0000:00:0e.0, config 040200, pass 1
[ 1.182441] PCI: Bus scan for 0000:00 returning with max=0a
[ 1.182446] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.182552] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IP2P._PRT]
[ 1.183339] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE0._PRT]
[ 1.183469] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE1._PRT]
[ 1.183600] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE2._PRT]
[ 1.186751] ACPI: PCI Root Bridge [PCI1] (0000:40)
[ 1.187368] PCI: Scanning bus 0000:40
[ 1.187387] PCI: Found 0000:40:00.0 [10de/005e] 000580 00
[ 1.187420] PCI: Found 0000:40:01.0 [10de/00d3] 000580 00
[ 1.187458] PCI: Found 0000:40:0b.0 [10de/005d] 000604 01
[ 1.187481] PCI: Found 0000:40:0c.0 [10de/005d] 000604 01
[ 1.187503] PCI: Found 0000:40:0d.0 [10de/005d] 000604 01
[ 1.187525] PCI: Found 0000:40:0e.0 [10de/005d] 000604 01
[ 1.187549] PCI: Found 0000:40:10.0 [1022/7458] 000604 01
[ 1.187565] PCI: Found 0000:40:10.1 [1022/7459] 000800 00
[ 1.187599] PCI: Found 0000:40:11.0 [1022/7458] 000604 01
[ 1.187615] PCI: Found 0000:40:11.1 [1022/7459] 000800 00
[ 1.187644] PCI: Fixups for bus 0000:40
[ 1.187646] PCI: Scanning behind PCI bridge 0000:40:0b.0, config 514f40, pass 0
[ 1.187651] PCI: Scanning bus 0000:4f
[ 1.187675] PCI: Fixups for bus 0000:4f
[ 1.187681] PCI: Bus scan for 0000:4f returning with max=4f
[ 1.187684] PCI: Scanning behind PCI bridge 0000:40:0c.0, config 4e4c40, pass 0
[ 1.187687] PCI: Scanning bus 0000:4c
[ 1.187712] PCI: Fixups for bus 0000:4c
[ 1.187717] PCI: Bus scan for 0000:4c returning with max=4c
[ 1.187720] PCI: Scanning behind PCI bridge 0000:40:0d.0, config 4b4940, pass 0
[ 1.187724] PCI: Scanning bus 0000:49
[ 1.187748] PCI: Fixups for bus 0000:49
[ 1.187754] PCI: Bus scan for 0000:49 returning with max=49
[ 1.187756] PCI: Scanning behind PCI bridge 0000:40:0e.0, config 484640, pass 0
[ 1.188313] PCI: Scanning bus 0000:46
[ 1.188338] PCI: Fixups for bus 0000:46
[ 1.188343] PCI: Bus scan for 0000:46 returning with max=46
[ 1.188346] PCI: Scanning behind PCI bridge 0000:40:10.0, config 414140, pass 0
[ 1.188351] PCI: Scanning bus 0000:41
[ 1.188370] PCI: Found 0000:41:01.0 [14e4/164a] 000200 00
[ 1.188409] PCI: Found 0000:41:02.0 [14e4/164a] 000200 00
[ 1.188448] PCI: Fixups for bus 0000:41
[ 1.188453] PCI: Bus scan for 0000:41 returning with max=41
[ 1.188456] PCI: Scanning behind PCI bridge 0000:40:11.0, config 454240, pass 0
[ 1.188460] PCI: Scanning bus 0000:42
[ 1.188479] PCI: Found 0000:42:01.0 [1000/0054] 000100 00
[ 1.188518] PCI: Found 0000:42:02.0 [103c/3220] 000104 00
[ 1.188557] PCI: Fixups for bus 0000:42
[ 1.188562] PCI: Bus scan for 0000:42 returning with max=42
[ 1.188565] PCI: Scanning behind PCI bridge 0000:40:0b.0, config 514f40, pass 1
[ 1.188569] PCI: Scanning behind PCI bridge 0000:40:0c.0, config 4e4c40, pass 1
[ 1.188572] PCI: Scanning behind PCI bridge 0000:40:0d.0, config 4b4940, pass 1
[ 1.188575] PCI: Scanning behind PCI bridge 0000:40:0e.0, config 484640, pass 1
[ 1.188579] PCI: Scanning behind PCI bridge 0000:40:10.0, config 414140, pass 1
[ 1.188582] PCI: Scanning behind PCI bridge 0000:40:11.0, config 454240, pass 1
[ 1.188585] PCI: Bus scan for 0000:40 returning with max=51
[ 1.188592] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.BRGA._PRT]
[ 1.188691] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.BRGB._PRT]
[ 1.188865] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE0._PRT]
[ 1.189005] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE1._PRT]
[ 1.189143] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE2._PRT]
[ 1.189280] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE3._PRT]
[ 1.191319] ACPI: PCI Interrupt Link [LNKW] (IRQs 16) *0, disabled.
[ 1.195468] ACPI: PCI Interrupt Link [LNKX] (IRQs 17) *0, disabled.
[ 1.199466] ACPI: PCI Interrupt Link [LNKY] (IRQs 18) *0, disabled.
[ 1.202849] ACPI: PCI Interrupt Link [LNKZ] (IRQs 19) *0, disabled.
[ 1.206461] ACPI: PCI Interrupt Link [LNU0] (IRQs 22) *5
[ 1.209410] ACPI: PCI Interrupt Link [LNU2] (IRQs 23) *10
[ 1.212438] ACPI: PCI Interrupt Link [LNKA] (IRQs 54) *0, disabled.
[ 1.215781] ACPI: PCI Interrupt Link [LNKB] (IRQs 55) *0, disabled.
[ 1.218772] ACPI: PCI Interrupt Link [LNKC] (IRQs 56) *0, disabled.
[ 1.221785] ACPI: PCI Interrupt Link [LNKD] (IRQs 57) *0, disabled.
[ 1.225491] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 1.226350] pnp: PnP ACPI init
[ 1.227310] ACPI: bus type pnp registered
[ 1.233440] pnp: PnP ACPI: found 16 devices
[ 1.234304] ACPI: ACPI bus type pnp unregistered
[ 1.236350] SCSI subsystem initialized
[ 1.237556] libata version 3.00 loaded.
[ 1.237710] usbcore: registered new interface driver usbfs
[ 1.238361] usbcore: registered new interface driver hub
[ 1.239370] usbcore: registered new device driver usb
[ 1.241382] PCI: Using ACPI for IRQ routing
[ 1.250320] NetLabel: Initializing
[ 1.251302] NetLabel: domain hash size = 128
[ 1.252301] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.253313] NetLabel: unlabeled traffic allowed by default
[ 1.254303] DMAR:parse DMAR table failure.
[ 1.255415] PCI-DMA: Disabling AGP.
[ 1.258094] PCI-DMA: aperture base @ 4000000 size 65536 KB
[ 1.258300] PCI-DMA: using GART IOMMU.
[ 1.259302] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 1.261586] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[ 1.264702] hpet0: 3 32-bit timers, 25000000 Hz
[ 1.267306] Switched to high resolution mode on CPU 0
[ 2.526693] Switched to high resolution mode on CPU 4
[ 3.107667] Switched to high resolution mode on CPU 1
[ 3.107667] Switched to high resolution mode on CPU 5
[ 3.107667] Switched to high resolution mode on CPU 2
[ 3.107667] Switched to high resolution mode on CPU 6
[ 3.107667] Switched to high resolution mode on CPU 3
[ 3.107667] Switched to high resolution mode on CPU 7
[ 3.107667] ACPI: RTC can wake from S4
[ 3.132946] system 00:01: ioport range 0x408-0x40f has been reserved
[ 3.157904] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 3.194551] system 00:01: ioport range 0x700-0x73f has been reserved
[ 3.198288] system 00:01: ioport range 0x800-0x8fe has been reserved
[ 3.228149] system 00:01: ioport range 0x900-0x9fe has been reserved
[ 3.264581] system 00:01: ioport range 0x9ff-0x9ff has been reserved
[ 3.293219] system 00:01: ioport range 0xa00-0xafe has been reserved
[ 3.329567] system 00:01: ioport range 0xaff-0xaff has been reserved
[ 3.355566] system 00:01: ioport range 0xb00-0xbfe has been reserved
[ 3.391978] system 00:01: ioport range 0xbff-0xbff has been reserved
[ 3.427525] system 00:01: ioport range 0xc80-0xc83 has been reserved
[ 3.455298] system 00:01: ioport range 0xcd4-0xcd7 has been reserved
[ 3.491561] system 00:01: ioport range 0xcf9-0xcf9 could not be reserved
[ 3.529549] system 00:01: ioport range 0xf50-0xf58 has been reserved
[ 3.565510] system 00:01: ioport range 0xca0-0xca1 has been reserved
[ 3.569256] system 00:01: ioport range 0xca4-0xca5 has been reserved
[ 3.605550] system 00:01: ioport range 0xc00-0xc03 has been reserved
[ 3.631447] system 00:01: ioport range 0x2f8-0x2ff has been reserved
[ 3.668986] got res [d9d00000:d9d1ffff] bus [d9d00000:d9d1ffff] flags 27200 for BAR 6 of 0000:01:03.0
[ 3.668989] got res [d9d20000:d9d2ffff] bus [d9d20000:d9d2ffff] flags 27200 for BAR 6 of 0000:01:04.2
[ 3.668992] PCI: Bridge: 0000:00:09.0
[ 3.689347] IO window: 1000-2fff
[ 3.709284] MEM window: 0xd9d00000-0xd9efffff
[ 3.734192] PREFETCH window: 0x00000000d0000000-0x00000000d7ffffff
[ 3.767539] PCI: Bridge: 0000:00:0c.0
[ 3.787162] IO window: disabled.
[ 3.807282] MEM window: disabled.
[ 3.826178] PREFETCH window: disabled.
[ 3.849160] PCI: Bridge: 0000:00:0d.0
[ 3.869163] IO window: disabled.
[ 3.889162] MEM window: disabled.
[ 3.908154] PREFETCH window: disabled.
[ 3.931165] PCI: Bridge: 0000:00:0e.0
[ 3.951170] IO window: disabled.
[ 3.971163] MEM window: disabled.
[ 3.973611] PREFETCH window: disabled.
[ 3.981136] PCI: Setting latency timer of device 0000:00:09.0 to 64
[ 3.981143] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 3.981148] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 3.981153] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 3.981159] PCI: Bridge: 0000:40:0b.0
[ 3.992176] IO window: disabled.
[ 4.011147] MEM window: disabled.
[ 4.030575] PREFETCH window: disabled.
[ 4.053147] PCI: Bridge: 0000:40:0c.0
[ 4.073161] IO window: disabled.
[ 4.093148] MEM window: disabled.
[ 4.112140] PREFETCH window: disabled.
[ 4.135135] PCI: Bridge: 0000:40:0d.0
[ 4.155193] IO window: disabled.
[ 4.174183] MEM window: disabled.
[ 4.193165] PREFETCH window: disabled.
[ 4.199609] PCI: Bridge: 0000:40:0e.0
[ 4.220147] IO window: disabled.
[ 4.240068] MEM window: disabled.
[ 4.257315] PREFETCH window: disabled.
[ 4.279139] got res [d9f00000:d9f1ffff] bus [d9f00000:d9f1ffff] flags 27200 for BAR 6 of 0000:41:01.0
[ 4.279142] got res [d9f20000:d9f3ffff] bus [d9f20000:d9f3ffff] flags 27200 for BAR 6 of 0000:41:02.0
[ 4.279144] PCI: Bridge: 0000:40:10.0
[ 4.299135] IO window: disabled.
[ 4.319148] MEM window: 0xda000000-0xddffffff
[ 4.333140] PREFETCH window: 0x00000000d9f00000-0x00000000d9ffffff
[ 4.370170] got res [de000000:de1fffff] bus [de000000:de1fffff] flags 27200 for BAR 6 of 0000:42:01.0
[ 4.370173] got res [de200000:de23ffff] bus [de200000:de23ffff] flags 27200 for BAR 6 of 0000:42:02.0
[ 4.370175] PCI: Bridge: 0000:40:11.0
[ 4.390143] IO window: 3000-3fff
[ 4.410177] MEM window: 0xdfe00000-0xdfefffff
[ 4.435157] PREFETCH window: 0x00000000de000000-0x00000000de2fffff
[ 4.472159] PCI: Setting latency timer of device 0000:40:0b.0 to 64
[ 4.472165] PCI: Setting latency timer of device 0000:40:0c.0 to 64
[ 4.472172] PCI: Setting latency timer of device 0000:40:0d.0 to 64
[ 4.472178] PCI: Setting latency timer of device 0000:40:0e.0 to 64
[ 4.472212] NET: Registered protocol family 2
[ 4.494783] IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 4.531692] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 4.581320] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 4.610273] TCP: Hash tables configured (established 524288 bind 65536)
[ 4.647561] TCP reno registered
[ 4.668827] NET: Registered protocol family 1
[ 4.688834] checking if image is initramfs... it is
[ 4.882738] Freeing initrd memory: 2668k freed
[ 4.913830] microcode: CPU0 not a capable Intel processor
[ 4.927851] microcode: CPU1 not a capable Intel processor
[ 4.940553] microcode: CPU2 not a capable Intel processor
[ 4.971303] microcode: CPU3 not a capable Intel processor
[ 4.971303] microcode: CPU4 not a capable Intel processor
[ 5.017031] microcode: CPU5 not a capable Intel processor
[ 5.054072] microcode: CPU6 not a capable Intel processor
[ 5.083505] microcode: CPU7 not a capable Intel processor
[ 5.104468] IA-32 Microcode Update Driver: v1.14a <tigran@xxxxxxxxxxxxxxxxxxxx>
[ 5.147060] audit: initializing netlink socket (disabled)
[ 5.167030] type=2000 audit(1247141644.906:1): initialized
[ 5.195810] Total HugeTLB memory allocated, 0
[ 5.223594] VFS: Disk quotas dquot_6.5.1
[ 5.237709] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 5.275549] SELinux: Registering netfilter hooks
[ 5.275747] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 5.318451] io scheduler noop registered
[ 5.340224] io scheduler anticipatory registered
[ 5.356173] io scheduler deadline registered
[ 5.379496] io scheduler cfq registered (default)
[ 5.405233] pci 0000:00:00.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.405256] pci 0000:00:00.0: Enabling HT MSI Mapping
[ 5.434249] pci 0000:00:00.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.434256] pci 0000:00:00.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.434260] pci 0000:00:00.0: calling pci_fixup_video+0x0/0xaf()
[ 5.434265] pci 0000:00:01.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.434272] pci 0000:00:01.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.434274] pci 0000:00:01.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.434277] pci 0000:00:01.0: calling pci_fixup_video+0x0/0xaf()
[ 5.434281] pci 0000:00:02.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.434289] pci 0000:00:02.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.434292] pci 0000:00:02.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.444865] pci 0000:00:02.0: calling pci_fixup_video+0x0/0xaf()
[ 5.444870] pci 0000:00:02.1: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.444879] pci 0000:00:02.1: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.444882] pci 0000:00:02.1: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.444889] pci 0000:00:02.1: EHCI: BIOS handoff
[ 5.456422] pci 0000:00:02.1: calling pci_fixup_video+0x0/0xaf()
[ 5.456427] pci 0000:00:06.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.456434] pci 0000:00:06.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.456437] pci 0000:00:06.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.456440] pci 0000:00:06.0: calling pci_fixup_video+0x0/0xaf()
[ 5.456444] pci 0000:00:09.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.456450] pci 0000:00:09.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.456453] pci 0000:00:09.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.456456] pci 0000:00:09.0: calling pci_fixup_video+0x0/0xaf()
[ 5.456460] pci 0000:00:0c.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.456469] pci 0000:00:0c.0: Enabling HT MSI Mapping
[ 5.476827] pci 0000:00:0c.0: calling quirk_nvidia_ck804_msi_ht_cap+0x0/0x7a()
[ 5.476834] pci 0000:00:0c.0: Found enabled HT MSI Mapping
[ 5.493134] pci 0000:00:0c.0: calling quirk_nvidia_ck804_pcie_aer_ext_cap+0x0/0x6a()
[ 5.493138] pci 0000:00:0c.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.493140] pci 0000:00:0c.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.493143] pci 0000:00:0c.0: calling pci_fixup_video+0x0/0xaf()
[ 5.493148] pci 0000:00:0d.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.493156] pci 0000:00:0d.0: Enabling HT MSI Mapping
[ 5.517594] pci 0000:00:0d.0: calling quirk_nvidia_ck804_msi_ht_cap+0x0/0x7a()
[ 5.517600] pci 0000:00:0d.0: Found enabled HT MSI Mapping
[ 5.549104] pci 0000:00:0d.0: calling quirk_nvidia_ck804_pcie_aer_ext_cap+0x0/0x6a()
[ 5.549107] pci 0000:00:0d.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.549110] pci 0000:00:0d.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.549113] pci 0000:00:0d.0: calling pci_fixup_video+0x0/0xaf()
[ 5.549117] pci 0000:00:0e.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.549125] pci 0000:00:0e.0: Enabling HT MSI Mapping
[ 5.577105] pci 0000:00:0e.0: calling quirk_nvidia_ck804_msi_ht_cap+0x0/0x7a()
[ 5.577111] pci 0000:00:0e.0: Found enabled HT MSI Mapping
[ 5.609127] pci 0000:00:0e.0: calling quirk_nvidia_ck804_pcie_aer_ext_cap+0x0/0x6a()
[ 5.609130] pci 0000:00:0e.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609133] pci 0000:00:0e.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609135] pci 0000:00:0e.0: calling pci_fixup_video+0x0/0xaf()
[ 5.609139] pci 0000:00:18.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609142] pci 0000:00:18.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609145] pci 0000:00:18.0: calling pci_fixup_video+0x0/0xaf()
[ 5.609149] pci 0000:00:18.1: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609151] pci 0000:00:18.1: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609154] pci 0000:00:18.1: calling pci_fixup_video+0x0/0xaf()
[ 5.609158] pci 0000:00:18.2: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609161] pci 0000:00:18.2: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609163] pci 0000:00:18.2: calling pci_fixup_video+0x0/0xaf()
[ 5.609167] pci 0000:00:18.3: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609170] pci 0000:00:18.3: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609173] pci 0000:00:18.3: calling pci_fixup_video+0x0/0xaf()
[ 5.609177] pci 0000:00:19.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609179] pci 0000:00:19.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609182] pci 0000:00:19.0: calling pci_fixup_video+0x0/0xaf()
[ 5.609186] pci 0000:00:19.1: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609189] pci 0000:00:19.1: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609191] pci 0000:00:19.1: calling pci_fixup_video+0x0/0xaf()
[ 5.609195] pci 0000:00:19.2: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609198] pci 0000:00:19.2: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609201] pci 0000:00:19.2: calling pci_fixup_video+0x0/0xaf()
[ 5.609205] pci 0000:00:19.3: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609207] pci 0000:00:19.3: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609210] pci 0000:00:19.3: calling pci_fixup_video+0x0/0xaf()
[ 5.609214] pci 0000:00:1a.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609216] pci 0000:00:1a.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609219] pci 0000:00:1a.0: calling pci_fixup_video+0x0/0xaf()
[ 5.609223] pci 0000:00:1a.1: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609226] pci 0000:00:1a.1: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609229] pci 0000:00:1a.1: calling pci_fixup_video+0x0/0xaf()
[ 5.609233] pci 0000:00:1a.2: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609235] pci 0000:00:1a.2: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609238] pci 0000:00:1a.2: calling pci_fixup_video+0x0/0xaf()
[ 5.609242] pci 0000:00:1a.3: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609245] pci 0000:00:1a.3: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609247] pci 0000:00:1a.3: calling pci_fixup_video+0x0/0xaf()
[ 5.609251] pci 0000:00:1b.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609254] pci 0000:00:1b.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609257] pci 0000:00:1b.0: calling pci_fixup_video+0x0/0xaf()
[ 5.609261] pci 0000:00:1b.1: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609263] pci 0000:00:1b.1: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609266] pci 0000:00:1b.1: calling pci_fixup_video+0x0/0xaf()
[ 5.609270] pci 0000:00:1b.2: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609272] pci 0000:00:1b.2: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609275] pci 0000:00:1b.2: calling pci_fixup_video+0x0/0xaf()
[ 5.609279] pci 0000:00:1b.3: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609282] pci 0000:00:1b.3: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609285] pci 0000:00:1b.3: calling pci_fixup_video+0x0/0xaf()
[ 5.609289] pci 0000:01:03.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609292] pci 0000:01:03.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609295] pci 0000:01:03.0: calling pci_fixup_video+0x0/0xaf()
[ 5.609299] pci 0000:01:03.0: Boot video device
[ 5.609302] pci 0000:01:04.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609305] pci 0000:01:04.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609307] pci 0000:01:04.0: calling pci_fixup_video+0x0/0xaf()
[ 5.609312] pci 0000:01:04.2: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609314] pci 0000:01:04.2: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609317] pci 0000:01:04.2: calling pci_fixup_video+0x0/0xaf()
[ 5.609321] pci 0000:01:04.4: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.609324] pci 0000:01:04.4: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.609330] pci 0000:01:04.4: uhci_check_and_reset_hc: legsup = 0x0010
[ 5.609332] pci 0000:01:04.4: Performing full reset
[ 5.609341] pci 0000:01:04.4: HCRESET not completed yet!
[ 5.640051] pci 0000:01:04.4: calling pci_fixup_video+0x0/0xaf()
[ 5.640056] pci 0000:01:04.6: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.640058] pci 0000:01:04.6: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.640061] pci 0000:01:04.6: calling pci_fixup_video+0x0/0xaf()
[ 5.640066] pci 0000:40:00.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.640078] pci 0000:40:00.0: Enabling HT MSI Mapping
[ 5.660764] pci 0000:40:00.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.660767] pci 0000:40:00.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.660770] pci 0000:40:00.0: calling pci_fixup_video+0x0/0xaf()
[ 5.660775] pci 0000:40:01.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.660781] pci 0000:40:01.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.660784] pci 0000:40:01.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.660787] pci 0000:40:01.0: calling pci_fixup_video+0x0/0xaf()
[ 5.661762] pci 0000:40:0b.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.661772] pci 0000:40:0b.0: Enabling HT MSI Mapping
[ 5.682727] pci 0000:40:0b.0: calling quirk_nvidia_ck804_msi_ht_cap+0x0/0x7a()
[ 5.682734] pci 0000:40:0b.0: Found enabled HT MSI Mapping
[ 5.714012] pci 0000:40:0b.0: calling quirk_nvidia_ck804_pcie_aer_ext_cap+0x0/0x6a()
[ 5.714015] pci 0000:40:0b.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.714018] pci 0000:40:0b.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.714021] pci 0000:40:0b.0: calling pci_fixup_video+0x0/0xaf()
[ 5.714026] pci 0000:40:0c.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.714035] pci 0000:40:0c.0: Enabling HT MSI Mapping
[ 5.728255] pci 0000:40:0c.0: calling quirk_nvidia_ck804_msi_ht_cap+0x0/0x7a()
[ 5.728262] pci 0000:40:0c.0: Found enabled HT MSI Mapping
[ 5.759979] pci 0000:40:0c.0: calling quirk_nvidia_ck804_pcie_aer_ext_cap+0x0/0x6a()
[ 5.759982] pci 0000:40:0c.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.759985] pci 0000:40:0c.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.759988] pci 0000:40:0c.0: calling pci_fixup_video+0x0/0xaf()
[ 5.759992] pci 0000:40:0d.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.760002] pci 0000:40:0d.0: Enabling HT MSI Mapping
[ 5.788012] pci 0000:40:0d.0: calling quirk_nvidia_ck804_msi_ht_cap+0x0/0x7a()
[ 5.788019] pci 0000:40:0d.0: Found enabled HT MSI Mapping
[ 5.811750] pci 0000:40:0d.0: calling quirk_nvidia_ck804_pcie_aer_ext_cap+0x0/0x6a()
[ 5.811753] pci 0000:40:0d.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.811756] pci 0000:40:0d.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.811758] pci 0000:40:0d.0: calling pci_fixup_video+0x0/0xaf()
[ 5.811763] pci 0000:40:0e.0: calling nv_msi_ht_cap_quirk+0x0/0x106()
[ 5.811773] pci 0000:40:0e.0: Enabling HT MSI Mapping
[ 5.840025] pci 0000:40:0e.0: calling quirk_nvidia_ck804_msi_ht_cap+0x0/0x7a()
[ 5.840032] pci 0000:40:0e.0: Found enabled HT MSI Mapping
[ 5.871169] pci 0000:40:0e.0: calling quirk_nvidia_ck804_pcie_aer_ext_cap+0x0/0x6a()
[ 5.871172] pci 0000:40:0e.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.871175] pci 0000:40:0e.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.871178] pci 0000:40:0e.0: calling pci_fixup_video+0x0/0xaf()
[ 5.871182] pci 0000:40:10.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.871185] pci 0000:40:10.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.871188] pci 0000:40:10.0: calling pci_fixup_video+0x0/0xaf()
[ 5.871193] pci 0000:40:10.1: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.871196] pci 0000:40:10.1: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.871199] pci 0000:40:10.1: calling pci_fixup_video+0x0/0xaf()
[ 5.871203] pci 0000:40:11.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.871206] pci 0000:40:11.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.871209] pci 0000:40:11.0: calling pci_fixup_video+0x0/0xaf()
[ 5.871214] pci 0000:40:11.1: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.871216] pci 0000:40:11.1: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.871219] pci 0000:40:11.1: calling pci_fixup_video+0x0/0xaf()
[ 5.871224] pci 0000:41:01.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.871226] pci 0000:41:01.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.871229] pci 0000:41:01.0: calling pci_fixup_video+0x0/0xaf()
[ 5.871234] pci 0000:41:02.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.871237] pci 0000:41:02.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.871239] pci 0000:41:02.0: calling pci_fixup_video+0x0/0xaf()
[ 5.871244] pci 0000:42:01.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.871246] pci 0000:42:01.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.871249] pci 0000:42:01.0: calling pci_fixup_video+0x0/0xaf()
[ 5.871253] pci 0000:42:02.0: calling quirk_cardbus_legacy+0x0/0x1d()
[ 5.871256] pci 0000:42:02.0: calling quirk_usb_early_handoff+0x0/0x447()
[ 5.871259] pci 0000:42:02.0: calling pci_fixup_video+0x0/0xaf()
[ 5.874572] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 5.874588] assign_interrupt_mode Found MSI capability
[ 5.903122] Allocate Port Service[0000:00:0c.0:pcie00]
[ 5.903221] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 5.903234] assign_interrupt_mode Found MSI capability
[ 5.932146] Allocate Port Service[0000:00:0d.0:pcie00]
[ 5.932218] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 5.932231] assign_interrupt_mode Found MSI capability
[ 5.961108] Allocate Port Service[0000:00:0e.0:pcie00]
[ 5.961108] PCI: Setting latency timer of device 0000:40:0b.0 to 64
[ 5.961130] assign_interrupt_mode Found MSI capability
[ 5.990044] Allocate Port Service[0000:40:0b.0:pcie00]
[ 5.990155] PCI: Setting latency timer of device 0000:40:0c.0 to 64
[ 5.990173] assign_interrupt_mode Found MSI capability
[ 6.019152] Allocate Port Service[0000:40:0c.0:pcie00]
[ 6.019234] PCI: Setting latency timer of device 0000:40:0d.0 to 64
[ 6.019252] assign_interrupt_mode Found MSI capability
[ 6.049013] Allocate Port Service[0000:40:0d.0:pcie00]
[ 6.049097] PCI: Setting latency timer of device 0000:40:0e.0 to 64
[ 6.049115] assign_interrupt_mode Found MSI capability
[ 6.078003] Allocate Port Service[0000:40:0e.0:pcie00]
[ 6.078235] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 6.098382] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 6.143161] ACPI: Power Button (FF) [PWRF]
[ 6.168099] ACPI: ACPI0007:00 is registered as cooling_device0
[ 6.200739] ACPI: ACPI0007:01 is registered as cooling_device1
[ 6.233713] ACPI: ACPI0007:02 is registered as cooling_device2
[ 6.266724] ACPI: ACPI0007:03 is registered as cooling_device3
[ 6.299689] ACPI: ACPI0007:04 is registered as cooling_device4
[ 6.303212] ACPI: ACPI0007:05 is registered as cooling_device5
[ 6.323859] ACPI: ACPI0007:06 is registered as cooling_device6
[ 6.343922] ACPI: ACPI0007:07 is registered as cooling_device7
[ 6.388814] hpet_resources: 0xfed00000 is busy
[ 6.388974] Non-volatile memory driver v1.2
[ 6.412222] Linux agpgart interface v0.103
[ 6.436361] [drm] Initialized drm 1.1.0 20060810
[ 6.462673] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 6.743341] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 6.999126] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 7.033765] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 7.038325] brd: module loaded
[ 7.056647] loop: module loaded
[ 7.074198] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 7.108972] Copyright (c) 1999-2006 Intel Corporation.
[ 7.125220] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
[ 7.158167] e100: Copyright(c) 1999-2006 Intel Corporation
[ 7.189153] Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.7.4 (February 18, 2008)
[ 7.225170] ACPI: PCI Interrupt 0000:41:01.0[A] -> GSI 31 (level, low) -> IRQ 31
[ 7.599225] eth0: Broadcom NetXtreme II BCM5706 1000Base-T (A2) PCI-X 64-bit 100MHz found at mem dc000000, IRQ 31, node addr 00:1b:78:be:d1:50
[ 7.613869] ACPI: PCI Interrupt 0000:41:02.0[A] -> GSI 32 (level, low) -> IRQ 32
[ 7.976895] eth1: Broadcom NetXtreme II BCM5706 1000Base-T (A2) PCI-X 64-bit 100MHz found at mem da000000, IRQ 32, node addr 00:1b:78:be:d1:52
[ 8.050856] console [netcon0] enabled
[ 8.070300] netconsole: network logging started
[ 8.095549] input: Macintosh mouse button emulation as /devices/virtual/input/input1
[ 8.140617] Loading iSCSI transport class v2.0-869.
[ 8.168436] Driver 'sd' needs updating - please use bus_type methods
[ 8.204889] Driver 'sr' needs updating - please use bus_type methods
[ 8.226141] pata_amd 0000:00:06.0: version 0.3.10
[ 8.226184] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 8.226303] scsi0 : pata_amd
[ 8.230905] scsi1 : pata_amd
[ 8.246852] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x500 irq 14
[ 8.276628] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x508 irq 15
[ 8.479173] ata1.00: ATAPI: TEAC DV-W28ECW, G.C4, max MWDMA2
[ 8.491911] ata1: nv_mode_filter: 0x39f&0xfffff->0x39f, BIOS=0x0 (0x0) ACPI=0x0
[ 8.514793] ata1.00: configured for MWDMA2
[ 8.537803] ata2: port disabled. ignoring.
[ 8.552915] scsi 0:0:0:0: CD-ROM TEAC DV-W28ECW G.C4 PQ: 0 ANSI: 5
[ 8.627128] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 8.665496] Uniform CD-ROM driver Revision: 3.20
[ 8.692642] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 8.692766] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 8.713454] ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
[ 8.713749] ACPI: PCI Interrupt Link [LNU2] enabled at IRQ 23
[ 8.745193] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LNU2] -> GSI 23 (level, high) -> IRQ 23
[ 8.785342] PCI: Setting latency timer of device 0000:00:02.1 to 64
[ 8.785345] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 8.805245] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[ 8.829871] ehci_hcd 0000:00:02.1: reset hcs_params 0x10148a dbg=1 cc=1 pcc=4 !ppc ports=10
[ 8.829878] ehci_hcd 0000:00:02.1: reset portroute 0 0 0 0 0 0 0 0 0 0
[ 8.829880] ehci_hcd 0000:00:02.1: reset hcc_params a086 caching frame 256/512/1024 park
[ 8.829902] ehci_hcd 0000:00:02.1: park 0
[ 8.829905] ehci_hcd 0000:00:02.1: reset command 080b12 park=3 ithresh=8 Periodic period=1024 Reset HALT
[ 8.829908] ehci_hcd 0000:00:02.1: bogus port configuration: cc=1 x pcc=4 < ports=10
[ 8.829913] ehci_hcd 0000:00:02.1: debug port 1
[ 8.855208] PCI: cache line size of 64 is not supported by device 0000:00:02.1
[ 8.855210] ehci_hcd 0000:00:02.1: supports USB remote wakeup
[ 8.855219] ehci_hcd 0000:00:02.1: irq 23, io mem 0xd9cd0000
[ 8.888167] ehci_hcd 0000:00:02.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
[ 8.888171] ehci_hcd 0000:00:02.1: init command 010009 (park)=0 ithresh=1 period=256 RUN
[ 8.894170] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 8.936145] usb usb1: default language 0x0409
[ 8.937117] usb usb1: uevent
[ 8.937169] usb usb1: usb_probe_device
[ 8.937295] usb usb1: configuration #1 chosen from 1 choice
[ 8.968925] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 8.968934] usb 1-0:1.0: uevent
[ 8.968980] hub 1-0:1.0: usb_probe_interface
[ 8.968981] hub 1-0:1.0: usb_probe_interface - got id
[ 8.968983] hub 1-0:1.0: USB hub found
[ 8.990904] hub 1-0:1.0: 10 ports detected
[ 9.013879] hub 1-0:1.0: standalone hub
[ 9.013881] hub 1-0:1.0: no power switching (usb 1.0)
[ 9.013882] hub 1-0:1.0: individual port over-current protection
[ 9.013884] hub 1-0:1.0: power on to power good time: 20ms
[ 9.013888] hub 1-0:1.0: local power source is good
[ 9.013891] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 9.103750] hub 1-0:1.0: state 7 ports 10 chg 0000 evt 0000
[ 9.114950] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 9.114950] ehci_hcd 0000:00:02.1: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
[ 9.114956] hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
[ 9.152699] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 9.194839] usb usb1: Product: EHCI Host Controller
[ 9.219168] hub 1-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501
[ 9.221695] usb usb1: Manufacturer: Linux 2.6.25 ehci_hcd
[ 9.252670] usb usb1: SerialNumber: 0000:00:02.1
[ 9.270381] ehci_hcd 0000:00:02.1: port 6 high speed
[ 9.270384] ehci_hcd 0000:00:02.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
[ 9.279732] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 9.279735] ohci_hcd: block sizes: ed 80 td 96
[ 9.280773] ACPI: PCI Interrupt Link [LNU0] enabled at IRQ 22
[ 9.312498] ACPI: PCI Interrupt 0000:00:02.0[A] -> <6>usb 1-6: new high speed USB device using ehci_hcd and address 2
[ 9.365557] ehci_hcd 0000:00:02.1: port 6 high speed
[ 9.365562] ehci_hcd 0000:00:02.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
[ 9.373617] Link [LNU0] -> GSI 22 (level, high) -> IRQ 22
[ 9.404457] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 9.404459] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 9.434597] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[ 9.434597] usb 1-6: uevent
[ 9.471234] ohci_hcd 0000:00:02.0: created debug files
[ 9.471240] ohci_hcd 0000:00:02.0: irq 22, io mem 0xd9ce0000
[ 9.475648] usb 1-6: usb_probe_device
[ 9.475741] usb 1-6: configuration #1 chosen from 1 choice
[ 9.475815] usb 1-6: adding 1-6:1.0 (config #1, interface 0)
[ 9.475824] usb 1-6:1.0: uevent
[ 9.475874] hub 1-6:1.0: usb_probe_interface
[ 9.475875] hub 1-6:1.0: usb_probe_interface - got id
[ 9.475877] hub 1-6:1.0: USB hub found
[ 9.475938] hub 1-6:1.0: 4 ports detected
[ 9.475940] hub 1-6:1.0: standalone hub
[ 9.475941] hub 1-6:1.0: individual port power switching
[ 9.475943] hub 1-6:1.0: individual port over-current protection
[ 9.476125] hub 1-6:1.0: TT per port
[ 9.476127] hub 1-6:1.0: TT requires at most 8 FS bit times (666 ns)
[ 9.476128] hub 1-6:1.0: Port indicators are supported
[ 9.476130] hub 1-6:1.0: power on to power good time: 100ms
[ 9.476312] hub 1-6:1.0: local power source is good
[ 9.476315] hub 1-6:1.0: enabling power on all ports
[ 9.577266] usb 1-6: link qh256-0001/ffff81007f802140 start 255 [1/0 us]
[ 9.577277] usb 1-6: New USB device found, idVendor=04b4, idProduct=6560
[ 9.604084] usb 1-6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 9.623069] hub 1-6:1.0: state 7 ports 4 chg 0000 evt 0000
[ 9.627467] ohci_hcd 0000:00:02.0: OHCI controller state
[ 9.627470] ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers
[ 9.627473] ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3
[ 9.627475] ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0
[ 9.627477] ohci_hcd 0000:00:02.0: intrstatus 0x00000004 SF
[ 9.627480] ohci_hcd 0000:00:02.0: intrenable 0x8000004a MIE RHSC RD WDH
[ 9.627483] ohci_hcd 0000:00:02.0: hcca frame #0003
[ 9.627485] ohci_hcd 0000:00:02.0: roothub.a 0100120a POTPGT=1 NOCP NPS NDP=10(10)
[ 9.627488] ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000
[ 9.627490] ohci_hcd 0000:00:02.0: roothub.status 00008000 DRWE
[ 9.627493] ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00000100 PPS
[ 9.627495] ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS
[ 9.627498] ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00000100 PPS
[ 9.627500] ohci_hcd 0000:00:02.0: roothub.portstatus [3] 0x00000100 PPS
[ 9.627503] ohci_hcd 0000:00:02.0: roothub.portstatus [4] 0x00000100 PPS
[ 9.627505] ohci_hcd 0000:00:02.0: roothub.portstatus [5] 0x00000100 PPS
[ 9.627508] ohci_hcd 0000:00:02.0: roothub.portstatus [6] 0x00000100 PPS
[ 9.627510] ohci_hcd 0000:00:02.0: roothub.portstatus [7] 0x00000100 PPS
[ 9.627513] ohci_hcd 0000:00:02.0: roothub.portstatus [8] 0x00000100 PPS
[ 9.627515] ohci_hcd 0000:00:02.0: roothub.portstatus [9] 0x00000100 PPS
[ 9.627524] usb usb2: default language 0x0409
[ 9.627539] usb usb2: uevent
[ 9.627597] usb usb2: usb_probe_device
[ 9.627679] usb usb2: configuration #1 chosen from 1 choice
[ 9.641804] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 9.641812] usb 2-0:1.0: uevent
[ 9.641865] hub 2-0:1.0: usb_probe_interface
[ 9.641867] hub 2-0:1.0: usb_probe_interface - got id
[ 9.641868] hub 2-0:1.0: USB hub found
[ 9.663311] hub 2-0:1.0: 10 ports detected
[ 9.679872] hub 2-0:1.0: standalone hub
[ 9.679873] hub 2-0:1.0: no power switching (usb 1.0)
[ 9.679875] hub 2-0:1.0: no over-current protection
[ 9.679876] hub 2-0:1.0: power on to power good time: 2ms
[ 9.679880] hub 2-0:1.0: local power source is good
[ 9.679881] hub 2-0:1.0: trying to enable port power on non-switchable hub
[ 9.778257] hub 2-0:1.0: state 7 ports 10 chg 0000 evt 0000
[ 9.780949] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 9.815959] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 9.856843] usb usb2: Product: OHCI Host Controller
[ 9.883695] usb usb2: Manufacturer: Linux 2.6.25 ohci_hcd
[ 9.904720] usb usb2: SerialNumber: 0000:00:02.0
[ 9.914216] USB Universal Host Controller Interface driver v3.0
[ 9.948255] ACPI: PCI Interrupt Link [LNKX] enabled at IRQ 17
[ 9.980720] ACPI: PCI Interrupt 0000:01:04.4[B] -> Link [LNKX] -> GSI 17 (level, high) -> IRQ 17
[ 10.017120] uhci_hcd 0000:01:04.4: UHCI Host Controller
[ 10.045783] uhci_hcd 0000:01:04.4: new USB bus registered, assigned bus number 3
[ 10.088845] uhci_hcd 0000:01:04.4: detected 8 ports
[ 10.091750] uhci_hcd 0000:01:04.4: port count misdetected? forcing to 2 ports
[ 10.131707] uhci_hcd 0000:01:04.4: uhci_check_and_reset_hc: cmd = 0x0000
[ 10.131709] uhci_hcd 0000:01:04.4: Performing full reset
[ 10.131718] uhci_hcd 0000:01:04.4: HCRESET not completed yet!
[ 10.164672] uhci_hcd 0000:01:04.4: irq 17, io base 0x00001800
[ 10.197706] usb usb3: default language 0x0409
[ 10.197721] usb usb3: uevent
[ 10.197771] usb usb3: usb_probe_device
[ 10.198692] usb usb3: configuration #1 chosen from 1 choice
[ 10.230882] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[ 10.230894] usb 3-0:1.0: uevent
[ 10.230951] hub 3-0:1.0: usb_probe_interface
[ 10.230952] hub 3-0:1.0: usb_probe_interface - got id
[ 10.230954] hub 3-0:1.0: USB hub found
[ 10.251654] hub 3-0:1.0: 2 ports detected
[ 10.273897] hub 3-0:1.0: standalone hub
[ 10.273899] hub 3-0:1.0: no power switching (usb 1.0)
[ 10.273900] hub 3-0:1.0: individual port over-current protection
[ 10.273902] hub 3-0:1.0: power on to power good time: 2ms
[ 10.273905] hub 3-0:1.0: local power source is good
[ 10.273906] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 10.370239] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 10.373984] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 10.373984] uhci_hcd 0000:01:04.4: port 1 portsc 0083,00
[ 10.373991] hub 3-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
[ 10.411772] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.453897] usb usb3: Product: UHCI Host Controller
[ 10.478321] hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
[ 10.480787] usb usb3: Manufacturer: Linux 2.6.25 uhci_hcd
[ 10.511855] usb usb3: SerialNumber: 0000:01:04.4
[ 10.579880] usb 3-1: new full speed USB device using uhci_hcd and address 2
[ 10.746982] usb 3-1: skipped 1 descriptor after interface
[ 10.746984] usb 3-1: skipped 1 descriptor after interface
[ 10.750221] usb 3-1: default language 0x0409
[ 10.756719] usb 3-1: uevent
[ 10.756777] usb 3-1: usb_probe_device
[ 10.756874] usb 3-1: configuration #1 chosen from 1 choice
[ 10.776914] usb 3-1: adding 3-1:1.0 (config #1, interface 0)
[ 10.776925] usb 3-1:1.0: uevent
[ 10.780310] usb 3-1: adding 3-1:1.1 (config #1, interface 1)
[ 10.780320] usb 3-1:1.1: uevent
[ 10.783498] usb 3-1: New USB device found, idVendor=03f0, idProduct=1027
[ 10.821005] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 10.853788] usb 3-1: Product: Virtual Keyboard
[ 10.860738] usb 3-1: Manufacturer: HP
[ 10.869997] uhci_hcd 0000:01:04.4: port 2 portsc 0083,00
[ 10.870003] hub 3-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
[ 10.973554] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
[ 10.979704] ohci_hcd 0000:00:02.0: auto-stop root hub
[ 11.075546] usb 3-2: new full speed USB device using uhci_hcd and address 3
[ 11.150540] uhci_hcd 0000:01:04.4: port 2 portsc 0083,00
[ 11.150550] hub 3-0:1.0: unable to enumerate USB device on port 2
[ 11.175480] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004
[ 11.175494] uhci_hcd 0000:01:04.4: port 2 portsc 0083,00
[ 11.175499] hub 3-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
[ 11.279096] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
[ 11.381084] usb 3-2: new full speed USB device using uhci_hcd and address 4
[ 11.530595] usb 3-2: default language 0x0409
[ 11.537085] usb 3-2: uevent
[ 11.537142] usb 3-2: usb_probe_device
[ 11.537226] usb 3-2: configuration #1 chosen from 1 choice
[ 11.570049] usb 3-2: adding 3-2:1.0 (config #1, interface 0)
[ 11.570059] usb 3-2:1.0: uevent
[ 11.570115] hub 3-2:1.0: usb_probe_interface
[ 11.570117] hub 3-2:1.0: usb_probe_interface - got id
[ 11.570119] hub 3-2:1.0: USB hub found
[ 11.594448] hub 3-2:1.0: 7 ports detected
[ 11.617214] hub 3-2:1.0: standalone hub
[ 11.617216] hub 3-2:1.0: ganged power switching
[ 11.617217] hub 3-2:1.0: individual port over-current protection
[ 11.617219] hub 3-2:1.0: power on to power good time: 100ms
[ 11.621442] hub 3-2:1.0: local power source is good
[ 11.621444] hub 3-2:1.0: enabling power on all ports
[ 11.737081] uhci_hcd 0000:01:04.4: reserve dev 4 ep81-INT, period 128, phase 0, 12 us
[ 11.740175] usb 3-2: New USB device found, idVendor=03f0, idProduct=1327
[ 11.778093] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 11.786932] usb 3-2: Product: Virtual Hub
[ 11.800002] usb 3-2: Manufacturer: HP
[ 11.820048] hub 3-2:1.0: state 7 ports 7 chg 0000 evt 0000
[ 11.835746] usb 3-2: remote wakeup needed for autosuspend
[ 11.835746] usbcore: registered new interface driver usblp
[ 11.856431] Initializing USB Mass Storage driver...
[ 11.885465] usbcore: registered new interface driver usb-storage
[ 11.920375] USB Mass Storage support registered.
[ 11.947403] usbcore: registered new interface driver libusual
[ 11.962044] hub 1-6:1.0: hub_suspend
[ 11.962048] usb 1-6: unlink qh256-0001/ffff81007f802140 start 255 [1/0 us]
[ 11.962151] usb 1-6: usb auto-suspend
[ 11.973039] hub 2-0:1.0: hub_suspend
[ 11.973042] usb usb2: bus auto-suspend
[ 11.973045] ohci_hcd 0000:00:02.0: suspend root hub
[ 11.980380] PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
[ 12.022295] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 12.050544] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 12.060940] mice: PS/2 mouse device common for all mice
[ 12.166673] rtc_cmos 00:0a: rtc core: registered rtc_cmos as rtc0
[ 12.201262] rtc0: alarms up to one year, y3k
[ 12.216302] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@xxxxxxxxxx
[ 12.266196] cpuidle: using governor ladder
[ 12.268468] cpuidle: using governor menu
[ 12.291067] usbcore: registered new interface driver hiddev
[ 12.306290] usbhid 3-1:1.0: usb_probe_interface
[ 12.306292] usbhid 3-1:1.0: usb_probe_interface - got id
[ 12.310425] input: HP Virtual Keyboard as /devices/pci0000:00/0000:00:09.0/0000:01:04.4/usb3/3-1/3-1:1.0/input/input2
[ 12.354996] uhci_hcd 0000:01:04.4: reserve dev 2 ep81-INT, period 8, phase 4, 17 us
[ 12.358118] input,hidraw0: USB HID v1.01 Keyboard [HP Virtual Keyboard] on usb-0000:01:04.4-1
[ 12.388803] usbhid 3-1:1.1: usb_probe_interface
[ 12.388805] usbhid 3-1:1.1: usb_probe_interface - got id
[ 12.393977] input: HP Virtual Keyboard as /devices/pci0000:00/0000:00:09.0/0000:01:04.4/usb3/3-1/3-1:1.1/input/input3
[ 12.454616] input,hidraw1: USB HID v1.01 Mouse [HP Virtual Keyboard] on usb-0000:01:04.4-1
[ 12.473262] usbcore: registered new interface driver usbhid
[ 12.476588] usbhid: v2.6:USB HID core driver
[ 12.500072] Advanced Linux Sound Architecture Driver Version 1.0.16.
[ 12.527395] ALSA device list:
[ 12.543006] No soundcards found.
[ 12.563124] Netfilter messages via NETLINK v0.30.
[ 12.589129] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 12.616927] ctnetlink v0.93: registering with nfnetlink.
[ 12.648277] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.678672] TCP cubic registered
[ 12.693037] Initializing XFRM netlink socket
[ 12.707789] NET: Registered protocol family 10
[ 12.725226] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.755181] IPv6 over IPv4 tunneling driver
[ 12.780301] NET: Registered protocol family 17
[ 12.806591] RPC: Registered udp transport module.
[ 12.811471] RPC: Registered tcp transport module.
[ 12.837768] registered taskstats version 1
[ 12.847549] Magic number: 1:122:228
[ 12.868044] Freeing unused kernel memory: 408k freed
[ 12.897702] Write protecting the kernel read-only data: 6388k
[ 12.924198] framebuffer used greatest stack depth: 5960 bytes left
[ 13.011397] usb usb2: uevent
[ 13.011416] usb 2-0:1.0: uevent
[ 13.011507] usb usb1: uevent
[ 13.011523] usb 1-0:1.0: uevent
[ 13.011553] usb 1-6: uevent
[ 13.011570] usb 1-6:1.0: uevent
[ 13.011869] usb usb3: uevent
[ 13.011887] usb 3-0:1.0: uevent
[ 13.011922] usb 3-1: uevent
[ 13.011939] usb 3-1:1.0: uevent
[ 13.012026] usb 3-1:1.1: uevent
[ 13.012144] usb 3-2: uevent
[ 13.012161] usb 3-2:1.0: uevent
[ 13.175784] cdrom_id used greatest stack depth: 5600 bytes left
[ 13.175784] Fusion MPT base driver 3.04.06
[ 13.192260] Copyright (c) 1999-2007 LSI Corporation
[ 13.225574] Fusion MPT SAS Host driver 3.04.06
[ 13.271656] ACPI: PCI Interrupt 0000:42:01.0[A] -> GSI 24 (level, low) -> IRQ 24
[ 13.313693] mptbase: ioc0: Initiating bringup
[ 13.615399] ioc0: LSISAS1068 B0: Capabilities={Initiator}
[ 13.631958] mptbase: ioc0: PCI-MSI enabled
[ 13.982332] hub 1-0:1.0: hub_suspend
[ 13.982343] usb usb1: bus auto-suspend
[ 13.982346] ehci_hcd 0000:00:02.1: suspend root hub
[ 36.872494] scsi2 : ioc0: LSISAS1068 B0, FwRev=01142100h, Ports=1, MaxQ=511, IRQ=2296
[ 36.948001] scsi 2:0:0:0: Direct-Access HP DG036A9BB6 HPD0 PQ: 0 ANSI: 5
[ 36.995195] sd 2:0:0:0: [sda] 71132960 512-byte hardware sectors (36420 MB)
[ 37.035914] sd 2:0:0:0: [sda] Write Protect is off
[ 37.063054] sd 2:0:0:0: [sda] Mode Sense: cf 00 10 08
[ 37.065147] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 37.114806] sd 2:0:0:0: [sda] 71132960 512-byte hardware sectors (36420 MB)
[ 37.155485] sd 2:0:0:0: [sda] Write Protect is off
[ 37.182018] sd 2:0:0:0: [sda] Mode Sense: cf 00 10 08
[ 37.183138] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 37.211143] sda: unknown partition table
[ 37.242517] sd 2:0:0:0: [sda] Attached SCSI disk
[ 37.268186] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 37.292685] scsi 2:0:1:0: Direct-Access HP DG036A9BB6 HPD0 PQ: 0 ANSI: 5
[ 37.340726] sd 2:0:1:0: [sdb] 71132960 512-byte hardware sectors (36420 MB)
[ 37.371636] sd 2:0:1:0: [sdb] Write Protect is off
[ 37.388666] sd 2:0:1:0: [sdb] Mode Sense: cf 00 10 08
[ 37.390775] sd 2:0:1:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 37.404759] sd 2:0:1:0: [sdb] 71132960 512-byte hardware sectors (36420 MB)
[ 37.446150] sd 2:0:1:0: [sdb] Write Protect is off
[ 37.472626] sd 2:0:1:0: [sdb] Mode Sense: cf 00 10 08
[ 37.473746] sd 2:0:1:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 37.522861] sdb: unknown partition table
[ 37.552684] sd 2:0:1:0: [sdb] Attached SCSI disk
[ 37.580599] sd 2:0:1:0: Attached scsi generic sg2 type 0
[ 37.613265] scsi 2:0:2:0: Direct-Access HP DG036A9BB6 HPD0 PQ: 0 ANSI: 5
[ 37.662039] sd 2:0:2:0: [sdc] 71132960 512-byte hardware sectors (36420 MB)
[ 37.676116] sd 2:0:2:0: [sdc] Write Protect is off
[ 37.702860] sd 2:0:2:0: [sdc] Mode Sense: cf 00 10 08
[ 37.704950] sd 2:0:2:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 37.754616] sd 2:0:2:0: [sdc] 71132960 512-byte hardware sectors (36420 MB)
[ 37.795366] sd 2:0:2:0: [sdc] Write Protect is off
[ 37.821828] sd 2:0:2:0: [sdc] Mode Sense: cf 00 10 08
[ 37.822944] sd 2:0:2:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 37.872012] sdc: unknown partition table
[ 37.902934] sd 2:0:2:0: [sdc] Attached SCSI disk
[ 37.930861] sd 2:0:2:0: Attached scsi generic sg3 type 0
[ 37.963216] scsi 2:0:3:0: Direct-Access HP DG036A9BB6 HPD0 PQ: 0 ANSI: 5
[ 38.010873] sd 2:0:3:0: [sdd] 71132960 512-byte hardware sectors (36420 MB)
[ 38.050878] sd 2:0:3:0: [sdd] Write Protect is off
[ 38.077471] sd 2:0:3:0: [sdd] Mode Sense: cf 00 10 08
[ 38.078682] sd 2:0:3:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 38.107238] sd 2:0:3:0: [sdd] 71132960 512-byte hardware sectors (36420 MB)
[ 38.147982] sd 2:0:3:0: [sdd] Write Protect is off
[ 38.175436] sd 2:0:3:0: [sdd] Mode Sense: cf 00 10 08
[ 38.176556] sd 2:0:3:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 38.204641] sdd: unknown partition table
[ 38.234909] sd 2:0:3:0: [sdd] Attached SCSI disk
[ 38.254170] sd 2:0:3:0: Attached scsi generic sg4 type 0
[ 38.275322] scsi 2:0:4:0: Direct-Access HP DG072A8B54 HPD7 PQ: 0 ANSI: 5
[ 38.323289] sd 2:0:4:0: [sde] 143374738 512-byte hardware sectors (73408 MB)
[ 38.363997] sd 2:0:4:0: [sde] Write Protect is off
[ 38.384391] sd 2:0:4:0: [sde] Mode Sense: db 00 10 08
[ 38.386277] sd 2:0:4:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 38.415095] sd 2:0:4:0: [sde] 143374738 512-byte hardware sectors (73408 MB)
[ 38.456634] sd 2:0:4:0: [sde] Write Protect is off
[ 38.483460] sd 2:0:4:0: [sde] Mode Sense: db 00 10 08
[ 38.484738] sd 2:0:4:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 38.525386] sde: unknown partition table
[ 38.553861] sd 2:0:4:0: [sde] Attached SCSI disk
[ 38.580430] sd 2:0:4:0: Attached scsi generic sg5 type 0
[ 38.611775] scsi 2:0:5:0: Direct-Access HP DG072A8B54 HPD7 PQ: 0 ANSI: 5
[ 38.659335] sd 2:0:5:0: [sdf] 143374738 512-byte hardware sectors (73408 MB)
[ 38.701158] sd 2:0:5:0: [sdf] Write Protect is off
[ 38.718765] sd 2:0:5:0: [sdf] Mode Sense: db 00 10 08
[ 38.720965] sd 2:0:5:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 38.754862] sd 2:0:5:0: [sdf] 143374738 512-byte hardware sectors (73408 MB)
[ 38.796063] sd 2:0:5:0: [sdf] Write Protect is off
[ 38.820986] sd 2:0:5:0: [sdf] Mode Sense: db 00 10 08
[ 38.822262] sd 2:0:5:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 38.833360] sdf: sdf1 sdf2 < sdf5 >
[ 38.865851] sd 2:0:5:0: [sdf] Attached SCSI disk
[ 38.868565] sd 2:0:5:0: Attached scsi generic sg6 type 0
[ 38.899883] scsi 2:0:6:0: Direct-Access HP DG072A8B54 HPD7 PQ: 0 ANSI: 5
[ 38.948252] sd 2:0:6:0: [sdg] 143374738 512-byte hardware sectors (73408 MB)
[ 38.984043] sd 2:0:6:0: [sdg] Write Protect is off
[ 38.990480] sd 2:0:6:0: [sdg] Mode Sense: db 00 10 08
[ 38.991953] sd 2:0:6:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 39.025658] sd 2:0:6:0: [sdg] 143374738 512-byte hardware sectors (73408 MB)
[ 39.064015] sd 2:0:6:0: [sdg] Write Protect is off
[ 39.090491] sd 2:0:6:0: [sdg] Mode Sense: db 00 10 08
[ 39.091771] sd 2:0:6:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 39.121438] sdg: unknown partition table
[ 39.151611] sd 2:0:6:0: [sdg] Attached SCSI disk
[ 39.178617] sd 2:0:6:0: Attached scsi generic sg7 type 0
[ 39.210845] scsi 2:0:7:0: Direct-Access HP DG072A8B54 HPD7 PQ: 0 ANSI: 5
[ 39.226616] sd 2:0:7:0: [sdh] 143374738 512-byte hardware sectors (73408 MB)
[ 39.267495] sd 2:0:7:0: [sdh] Write Protect is off
[ 39.294680] sd 2:0:7:0: [sdh] Mode Sense: db 00 10 08
[ 39.296412] sd 2:0:7:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 39.337384] sd 2:0:7:0: [sdh] 143374738 512-byte hardware sectors (73408 MB)
[ 39.347909] sd 2:0:7:0: [sdh] Write Protect is off
[ 39.374711] sd 2:0:7:0: [sdh] Mode Sense: db 00 10 08
[ 39.375989] sd 2:0:7:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 39.424924] sdh: sdh1
[ 39.445631] sd 2:0:7:0: [sdh] Attached SCSI disk
[ 39.472528] sd 2:0:7:0: Attached scsi generic sg8 type 0
[ 39.504437] modprobe used greatest stack depth: 3336 bytes left
[ 39.766451] kjournald starting. Commit interval 5 seconds
[ 39.766451] EXT3-fs: mounted filesystem with ordered data mode.
[ 40.721346] udevd version 125 started
[ 40.801447] usb usb2: uevent
[ 40.801468] usb 2-0:1.0: uevent
[ 40.801564] usb usb1: uevent
[ 40.801581] usb 1-0:1.0: uevent
[ 40.801613] usb 1-6: uevent
[ 40.801630] usb 1-6:1.0: uevent
[ 40.801935] usb usb3: uevent
[ 40.801953] usb 3-0:1.0: uevent
[ 40.801986] usb 3-1: uevent
[ 40.802005] usb 3-1:1.0: uevent
[ 40.802097] usb 3-1:1.1: uevent
[ 40.802214] usb 3-2: uevent
[ 40.802232] usb 3-2:1.0: uevent
[ 41.925475] Adding 2963952k swap on /dev/sdf5. Priority:-1 extents:1 across:2963952k
[ 42.264323] EXT3 FS on sdf1, internal journal
[ 44.441511] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 47.533354] bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex
[ 47.570707] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 58.202303] eth0: no IPv6 routers present
--- pre.dmesg.trimmed 2009-07-09 12:35:10.000000000 -0600
+++ post.dmesg.trimmed 2009-07-09 12:35:17.000000000 -0600
@@ -1,6 +1,6 @@
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
-Linux version 2.6.25 (dannf@dl585g2) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #68 SMP Thu Jul 9 12:25:31 MDT 2009
+Linux version 2.6.25 (dannf@dl585g2) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #67 SMP Thu Jul 9 12:11:29 MDT 2009
Command line: root=/dev/disk/by-id/scsi-35000c50000d5ca0f-part1 ro console=tty1 console=ttyS1,115200
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e400 (usable)
@@ -65,8 +65,8 @@
bootmap [000000000002c000 - 000000000005bfff] pages 30
early res: 0 [0-fff] BIOS data page
early res: 1 [6000-7fff] TRAMPOLINE
- early res: 2 [200000-a88afb] TEXT DATA BSS
- early res: 3 [37d54000-37fef2b8] RAMDISK
+ early res: 2 [200000-a8a97b] TEXT DATA BSS
+ early res: 3 [37d54000-37fef2ed] RAMDISK
early res: 4 [9e400-fffff] BIOS reserved
early res: 5 [8000-19fff] PGTABLE
early res: 6 [1a000-2307f] MEMNODEMAP
@@ -99,8 +99,8 @@
3: 3670016 -> 4718591
On node 0 totalpages: 1047789
DMA zone: 56 pages used for memmap
- DMA zone: 2313 pages reserved
- DMA zone: 1629 pages, LIFO batch:0
+ DMA zone: 2315 pages reserved
+ DMA zone: 1627 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 505223 pages, LIFO batch:31
Normal zone: 7168 pages used for memmap
@@ -175,7 +175,7 @@
SMP: Allowing 8 CPUs, 0 hotplug CPUs
PERCPU: Allocating 44480 bytes of per cpu data
NR_CPUS: 64, nr_cpu_ids: 8
-Built 4 zonelists in Zone order, mobility grouping on. Total pages: 4126692
+Built 4 zonelists in Zone order, mobility grouping on. Total pages: 4126690
Policy zone: Normal
Kernel command line: root=/dev/disk/by-id/scsi-35000c50000d5ca0f-part1 ro console=tty1 console=ttyS1,115200
Initializing CPU#0
@@ -183,7 +183,7 @@
Extended CMOS year: 2000
TSC calibrated against PM_TIMER
Marking TSC unstable due to TSCs unsynchronized
-time.c: Detected 2612.039 MHz processor.
+time.c: Detected 2612.040 MHz processor.
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty1] enabled
@@ -197,11 +197,11 @@
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
PM: Registered nosave memory: 0000000004000000 - 0000000008000000
-Memory: 16466524k/18874364k available (4336k kernel code, 307540k reserved, 2815k data, 404k init)
+Memory: 16466516k/18874364k available (4337k kernel code, 307548k reserved, 2815k data, 408k init)
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=13, HWalign=64, Order=0-1, MinObjects=4, CPUs=8, Nodes=4
hpet clockevent registered
-Calibrating delay using timer specific routine.. 5226.25 BogoMIPS (lpj=2613125)
+Calibrating delay using timer specific routine.. 5226.24 BogoMIPS (lpj=2613121)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
@@ -220,11 +220,11 @@
ACPI: Core revision 20070126
CPU0: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
Using local APIC timer interrupts.
-APIC timer calibration result 12557872
+APIC timer calibration result 12557873
Detected 12.557 MHz APIC timer.
Booting processor 1/2 ip 6000
Initializing CPU#1
-Calibrating delay using timer specific routine.. 5223.88 BogoMIPS (lpj=2611941)
+Calibrating delay using timer specific routine.. 5223.83 BogoMIPS (lpj=2611917)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1/2 -> Node 1
@@ -234,7 +234,7 @@
CPU1: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
Booting processor 2/4 ip 6000
Initializing CPU#2
-Calibrating delay using timer specific routine.. 5223.84 BogoMIPS (lpj=2611922)
+Calibrating delay using timer specific routine.. 5223.89 BogoMIPS (lpj=2611947)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 2/4 -> Node 2
@@ -244,7 +244,7 @@
CPU2: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
Booting processor 3/6 ip 6000
Initializing CPU#3
-Calibrating delay using timer specific routine.. 5223.86 BogoMIPS (lpj=2611930)
+Calibrating delay using timer specific routine.. 5223.89 BogoMIPS (lpj=2611949)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 3/6 -> Node 3
@@ -254,7 +254,7 @@
CPU3: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
Booting processor 4/1 ip 6000
Initializing CPU#4
-Calibrating delay using timer specific routine.. 5223.82 BogoMIPS (lpj=2611910)
+Calibrating delay using timer specific routine.. 5223.81 BogoMIPS (lpj=2611905)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 4/1 -> Node 0
@@ -264,7 +264,7 @@
CPU4: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
Booting processor 5/3 ip 6000
Initializing CPU#5
-Calibrating delay using timer specific routine.. 5223.85 BogoMIPS (lpj=2611926)
+Calibrating delay using timer specific routine.. 5223.87 BogoMIPS (lpj=2611939)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 5/3 -> Node 1
@@ -274,7 +274,7 @@
CPU5: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
Booting processor 6/5 ip 6000
Initializing CPU#6
-Calibrating delay using timer specific routine.. 5223.87 BogoMIPS (lpj=2611937)
+Calibrating delay using timer specific routine.. 5223.85 BogoMIPS (lpj=2611928)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 6/5 -> Node 2
@@ -284,7 +284,7 @@
CPU6: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
Booting processor 7/7 ip 6000
Initializing CPU#7
-Calibrating delay using timer specific routine.. 5223.84 BogoMIPS (lpj=2611921)
+Calibrating delay using timer specific routine.. 5223.84 BogoMIPS (lpj=2611923)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 7/7 -> Node 3
@@ -293,12 +293,14 @@
x86: PAT support disabled.
CPU7: Dual-Core AMD Opteron(tm) Processor 8218 stepping 03
Brought up 8 CPUs
-Total of 8 processors activated (41793.22 BogoMIPS).
+Total of 8 processors activated (41793.25 BogoMIPS).
khelper used greatest stack depth: 6056 bytes left
net_namespace: 1176 bytes
-Time: 12:28:07 Date: 07/09/09
+Time: 12:14:05 Date: 07/09/09
NET: Registered protocol family 16
No dock devices found.
+TOM: 0000000080000000 aka 2048M
+TOM2: 0000000480000000 aka 18432M
bus: 00 to node: 00
bus: 01 to node: 00
bus: 02 to node: 00
@@ -427,6 +429,17 @@
bus: 7d to node: 01
bus: 7e to node: 01
bus: 7f to node: 01
+bus: [00,3f] on node 0 link 1
+bus: 00 index 0 io port: [0, 2fff]
+bus: 00 index 1 mmio: [80000000, d9efffff]
+bus: 00 index 2 mmio: [dff00000, e3ffffff]
+bus: 00 index 3 mmio: [a0000, bffff]
+bus: 00 index 4 mmio: [e8000000, ffffffff]
+bus: 00 index 5 mmio: [480000000, fbffffffff]
+bus: [40,7f] on node 1 link 2
+bus: 40 index 0 io port: [3000, ffff]
+bus: 40 index 1 mmio: [d9f00000, dfefffff]
+bus: 40 index 2 mmio: [e4000000, e7ffffff]
ACPI: bus type pci registered
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
@@ -581,7 +594,6 @@
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
hpet0: 3 32-bit timers, 25000000 Hz
-ACPI: RTC can wake from S4
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 4
Switched to high resolution mode on CPU 1
@@ -590,6 +602,7 @@
Switched to high resolution mode on CPU 6
Switched to high resolution mode on CPU 3
Switched to high resolution mode on CPU 7
+ACPI: RTC can wake from S4
system 00:01: ioport range 0x408-0x40f has been reserved
system 00:01: ioport range 0x4d0-0x4d1 has been reserved
system 00:01: ioport range 0x700-0x73f has been reserved
@@ -646,18 +659,18 @@
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
- got res [88000000:8801ffff] bus [88000000:8801ffff] flags 27200 for BAR 6 of 0000:41:01.0
- got res [88020000:8803ffff] bus [88020000:8803ffff] flags 27200 for BAR 6 of 0000:41:02.0
+ got res [d9f00000:d9f1ffff] bus [d9f00000:d9f1ffff] flags 27200 for BAR 6 of 0000:41:01.0
+ got res [d9f20000:d9f3ffff] bus [d9f20000:d9f3ffff] flags 27200 for BAR 6 of 0000:41:02.0
PCI: Bridge: 0000:40:10.0
IO window: disabled.
MEM window: 0xda000000-0xddffffff
- PREFETCH window: 0x0000000088000000-0x00000000880fffff
- got res [88200000:883fffff] bus [88200000:883fffff] flags 27200 for BAR 6 of 0000:42:01.0
- got res [88100000:8813ffff] bus [88100000:8813ffff] flags 27200 for BAR 6 of 0000:42:02.0
+ PREFETCH window: 0x00000000d9f00000-0x00000000d9ffffff
+ got res [de000000:de1fffff] bus [de000000:de1fffff] flags 27200 for BAR 6 of 0000:42:01.0
+ got res [de200000:de23ffff] bus [de200000:de23ffff] flags 27200 for BAR 6 of 0000:42:02.0
PCI: Bridge: 0000:40:11.0
IO window: 3000-3fff
MEM window: 0xdfe00000-0xdfefffff
- PREFETCH window: 0x0000000088100000-0x00000000883fffff
+ PREFETCH window: 0x00000000de000000-0x00000000de2fffff
PCI: Setting latency timer of device 0000:40:0b.0 to 64
PCI: Setting latency timer of device 0000:40:0c.0 to 64
PCI: Setting latency timer of device 0000:40:0d.0 to 64
@@ -681,7 +694,7 @@
microcode: CPU7 not a capable Intel processor
IA-32 Microcode Update Driver: v1.14a <tigran@xxxxxxxxxxxxxxxxxxxx>
audit: initializing netlink socket (disabled)
-type=2000 audit(1247142486.936:1): initialized
+type=2000 audit(1247141644.906:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
@@ -986,24 +999,24 @@
hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
-usb usb1: Manufacturer: Linux 2.6.25 ehci_hcd
hub 1-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501
+usb usb1: Manufacturer: Linux 2.6.25 ehci_hcd
usb usb1: SerialNumber: 0000:00:02.1
+ehci_hcd 0000:00:02.1: port 6 high speed
+ehci_hcd 0000:00:02.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 80 td 96
ACPI: PCI Interrupt Link [LNU0] enabled at IRQ 22
+ACPI: PCI Interrupt 0000:00:02.0[A] -> <6>usb 1-6: new high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:02.1: port 6 high speed
ehci_hcd 0000:00:02.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
-ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNU0] -> GSI 22 (level, high) -> IRQ 22
-usb 1-6: new high speed USB device using ehci_hcd and address 2
+Link [LNU0] -> GSI 22 (level, high) -> IRQ 22
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
-ehci_hcd 0000:00:02.1: port 6 high speed
-ehci_hcd 0000:00:02.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
+usb 1-6: uevent
ohci_hcd 0000:00:02.0: created debug files
ohci_hcd 0000:00:02.0: irq 22, io mem 0xd9ce0000
-usb 1-6: uevent
usb 1-6: usb_probe_device
usb 1-6: configuration #1 chosen from 1 choice
usb 1-6: adding 1-6:1.0 (config #1, interface 0)
@@ -1015,6 +1028,16 @@
hub 1-6:1.0: standalone hub
hub 1-6:1.0: individual port power switching
hub 1-6:1.0: individual port over-current protection
+hub 1-6:1.0: TT per port
+hub 1-6:1.0: TT requires at most 8 FS bit times (666 ns)
+hub 1-6:1.0: Port indicators are supported
+hub 1-6:1.0: power on to power good time: 100ms
+hub 1-6:1.0: local power source is good
+hub 1-6:1.0: enabling power on all ports
+usb 1-6: link qh256-0001/ffff81007f802140 start 255 [1/0 us]
+usb 1-6: New USB device found, idVendor=04b4, idProduct=6560
+usb 1-6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
+hub 1-6:1.0: state 7 ports 4 chg 0000 evt 0000
ohci_hcd 0000:00:02.0: OHCI controller state
ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3
@@ -1037,14 +1060,8 @@
ohci_hcd 0000:00:02.0: roothub.portstatus [9] 0x00000100 PPS
usb usb2: default language 0x0409
usb usb2: uevent
-hub 1-6:1.0: TT per port
-hub 1-6:1.0: TT requires at most 8 FS bit times (666 ns)
-hub 1-6:1.0: Port indicators are supported
-hub 1-6:1.0: power on to power good time: 100ms
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
-hub 1-6:1.0: local power source is good
-hub 1-6:1.0: enabling power on all ports
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
@@ -1057,10 +1074,6 @@
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: trying to enable port power on non-switchable hub
-usb 1-6: link qh256-0001/ffff81007f802140 start 255 [1/0 us]
-usb 1-6: New USB device found, idVendor=04b4, idProduct=6560
-usb 1-6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
-hub 1-6:1.0: state 7 ports 4 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 10 chg 0000 evt 0000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
@@ -1120,19 +1133,14 @@
usb 3-1: Manufacturer: HP
uhci_hcd 0000:01:04.4: port 2 portsc 0083,00
hub 3-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
-ohci_hcd 0000:00:02.0: auto-stop root hub
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
+ohci_hcd 0000:00:02.0: auto-stop root hub
usb 3-2: new full speed USB device using uhci_hcd and address 3
uhci_hcd 0000:01:04.4: port 2 portsc 0083,00
hub 3-0:1.0: unable to enumerate USB device on port 2
-hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
-usbcore: registered new interface driver usblp
-Initializing USB Mass Storage driver...
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004
uhci_hcd 0000:01:04.4: port 2 portsc 0083,00
hub 3-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
-usbcore: registered new interface driver usb-storage
-USB Mass Storage support registered.
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
usb 3-2: new full speed USB device using uhci_hcd and address 4
usb 3-2: default language 0x0409
@@ -1158,14 +1166,18 @@
usb 3-2: Manufacturer: HP
hub 3-2:1.0: state 7 ports 7 chg 0000 evt 0000
usb 3-2: remote wakeup needed for autosuspend
+usbcore: registered new interface driver usblp
+Initializing USB Mass Storage driver...
+usbcore: registered new interface driver usb-storage
+USB Mass Storage support registered.
usbcore: registered new interface driver libusual
-PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
hub 1-6:1.0: hub_suspend
usb 1-6: unlink qh256-0001/ffff81007f802140 start 255 [1/0 us]
usb 1-6: usb auto-suspend
hub 2-0:1.0: hub_suspend
usb usb2: bus auto-suspend
ohci_hcd 0000:00:02.0: suspend root hub
+PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
@@ -1202,10 +1214,10 @@
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
registered taskstats version 1
- Magic number: 1:878:480
-Freeing unused kernel memory: 404k freed
+ Magic number: 1:122:228
+Freeing unused kernel memory: 408k freed
Write protecting the kernel read-only data: 6388k
-blacklist used greatest stack depth: 5960 bytes left
+framebuffer used greatest stack depth: 5960 bytes left
usb usb2: uevent
usb 2-0:1.0: uevent
usb usb1: uevent
@@ -1219,7 +1231,7 @@
usb 3-1:1.1: uevent
usb 3-2: uevent
usb 3-2:1.0: uevent
-cdrom_id used greatest stack depth: 5752 bytes left
+cdrom_id used greatest stack depth: 5600 bytes left
Fusion MPT base driver 3.04.06
Copyright (c) 1999-2007 LSI Corporation
Fusion MPT SAS Host driver 3.04.06