Re: Linux 2.6.33-rc1
From: Torsten Kaiser
Date: Sun Dec 20 2009 - 14:41:13 EST
On Sun, Dec 20, 2009 at 8:36 PM, Torsten Kaiser
<just.for.lkml@xxxxxxxxxxxxxx> wrote:
> On Sun, Dec 20, 2009 at 8:14 PM, Borislav Petkov
> <petkovbb@xxxxxxxxxxxxxx> wrote:
>> That might be the case, can you enable CONFIG_EDAC_DEBUG and
>> CONFIG_EDAC_DEBUG_VERBOSE and rebuild your kernel, please? Then, send me
>> the _whole_ dmesg output. If the output appears truncated, try enlarging
>> the log buffer size by setting log_buf_len on the kernel command line to
>> something large, i.e. 'log_buf_len=10M'.
>
> Is attached...
GoogleMail didn't like the attachement on the first try, I hope it
will work this time.
Torsten
[ 0.000000] Linux version 2.6.33-rc1 (root@treogen) (gcc version 4.4.2 (Gentoo 4.4.2 p1.0) ) #2 SMP Sun Dec 20 20:27:30 CET 2009
[ 0.000000] Command line: fastboot earlyprintk=serial,ttyS0,115200 console=ttyS0,115200 console=tty1 crypt_root=/dev/md3 radeon.modeset=1
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000dffd0000 (usable)
[ 0.000000] BIOS-e820: 00000000dffd0000 - 00000000dffde000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000dffde000 - 00000000e0000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
[ 0.000000] bootconsole [earlyser0] enabled
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI present.
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x120000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask FF80000000 write-back
[ 0.000000] 1 base 0080000000 mask FFC0000000 write-back
[ 0.000000] 2 base 00C0000000 mask FFE0000000 write-back
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 0000000120000000 aka 4608M
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820 update range: 00000000e0000000 - 0000000100000000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0xdffd0 max_arch_pfn = 0x400000000
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] found SMP MP-table at [ffff8800000ff780] ff780
[ 0.000000] init_memory_mapping: 0000000000000000-00000000dffd0000
[ 0.000000] 0000000000 - 00dfe00000 page 2M
[ 0.000000] 00dfe00000 - 00dffd0000 page 4k
[ 0.000000] kernel direct mapping tables up to dffd0000 @ 8000-e000
[ 0.000000] init_memory_mapping: 0000000100000000-0000000120000000
[ 0.000000] 0100000000 - 0120000000 page 2M
[ 0.000000] kernel direct mapping tables up to 120000000 @ c000-12000
[ 0.000000] RAMDISK: 37ec8000 - 37fefd0e
[ 0.000000] ACPI: RSDP 00000000000fb080 00024 (v02 ACPIAM)
[ 0.000000] ACPI: XSDT 00000000dffd0100 00064 (v01 A_M_I_ OEMXSDT 04000713 MSFT 00000097)
[ 0.000000] ACPI: FACP 00000000dffd0290 000F4 (v03 A_M_I_ OEMFACP 04000713 MSFT 00000097)
[ 0.000000] ACPI: DSDT 00000000dffd0450 04FC5 (v01 S0027 S0027000 00000000 INTL 20051117)
[ 0.000000] ACPI: FACS 00000000dffde000 00040
[ 0.000000] ACPI: APIC 00000000dffd0390 00080 (v01 A_M_I_ OEMAPIC 04000713 MSFT 00000097)
[ 0.000000] ACPI: MCFG 00000000dffd0410 0003C (v01 A_M_I_ OEMMCFG 04000713 MSFT 00000097)
[ 0.000000] ACPI: OEMB 00000000dffde040 00060 (v01 A_M_I_ AMI_OEM 04000713 MSFT 00000097)
[ 0.000000] ACPI: HPET 00000000dffd5420 00038 (v01 A_M_I_ OEMHPET0 04000713 MSFT 00000097)
[ 0.000000] ACPI: MCFG 00000000dffd5460 0003C (v01 A_M_I_ OEMMCFG 04000713 MSFT 00000097)
[ 0.000000] ACPI: SRAT 00000000dffd54a0 00110 (v01 AMD HAMMER 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 00000000dffd55b0 004F0 (v01 A_M_I_ POWERNOW 00000001 AMD 00000001)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] SRAT: PXM 0 -> APIC 0x00 -> Node 0
[ 0.000000] SRAT: PXM 0 -> APIC 0x01 -> Node 0
[ 0.000000] SRAT: PXM 1 -> APIC 0x02 -> Node 1
[ 0.000000] SRAT: PXM 1 -> APIC 0x03 -> Node 1
[ 0.000000] SRAT: Node 0 PXM 0 0-a0000
[ 0.000000] SRAT: Node 0 PXM 0 100000-80000000
[ 0.000000] SRAT: Node 1 PXM 1 80000000-e0000000
[ 0.000000] SRAT: Node 1 PXM 1 100000000-120000000
[ 0.000000] NUMA: Allocated memnodemap from d000 - f440
[ 0.000000] NUMA: Using 20 for the hash shift.
[ 0.000000] Bootmem setup node 0 0000000000000000-0000000080000000
[ 0.000000] NODE_DATA [000000000000f440 - 000000000002343f]
[ 0.000000] bootmap [0000000000024000 - 0000000000033fff] pages 10
[ 0.000000] (13 early reservations) ==> bootmem [0000000000 - 0080000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0001000000 - 0001a074d8] TEXT DATA BSS ==> [0001000000 - 0001a074d8]
[ 0.000000] #2 [0037ec8000 - 0037fefd0e] RAMDISK ==> [0037ec8000 - 0037fefd0e]
[ 0.000000] #3 [0001a08000 - 0001a08238] BRK ==> [0001a08000 - 0001a08238]
[ 0.000000] #4 [00000ff790 - 0000100000] BIOS reserved ==> [00000ff790 - 0000100000]
[ 0.000000] #5 [00000ff780 - 00000ff790] MP-table mpf ==> [00000ff780 - 00000ff790]
[ 0.000000] #6 [000009fc00 - 00000f16f0] BIOS reserved ==> [000009fc00 - 00000f16f0]
[ 0.000000] #7 [00000f188c - 00000ff780] BIOS reserved ==> [00000f188c - 00000ff780]
[ 0.000000] #8 [00000f16f0 - 00000f188c] MP-table mpc ==> [00000f16f0 - 00000f188c]
[ 0.000000] #9 [0000001000 - 0000003000] TRAMPOLINE ==> [0000001000 - 0000003000]
[ 0.000000] #10 [0000008000 - 000000c000] PGTABLE ==> [0000008000 - 000000c000]
[ 0.000000] #11 [000000c000 - 000000d000] PGTABLE ==> [000000c000 - 000000d000]
[ 0.000000] #12 [000000d000 - 000000f440] MEMNODEMAP ==> [000000d000 - 000000f440]
[ 0.000000] Bootmem setup node 1 0000000080000000-0000000120000000
[ 0.000000] NODE_DATA [0000000080000000 - 0000000080013fff]
[ 0.000000] bootmap [0000000080014000 - 0000000080027fff] pages 14
[ 0.000000] (13 early reservations) ==> bootmem [0080000000 - 0120000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page
[ 0.000000] #1 [0001000000 - 0001a074d8] TEXT DATA BSS
[ 0.000000] #2 [0037ec8000 - 0037fefd0e] RAMDISK
[ 0.000000] #3 [0001a08000 - 0001a08238] BRK
[ 0.000000] #4 [00000ff790 - 0000100000] BIOS reserved
[ 0.000000] #5 [00000ff780 - 00000ff790] MP-table mpf
[ 0.000000] #6 [000009fc00 - 00000f16f0] BIOS reserved
[ 0.000000] #7 [00000f188c - 00000ff780] BIOS reserved
[ 0.000000] #8 [00000f16f0 - 00000f188c] MP-table mpc
[ 0.000000] #9 [0000001000 - 0000003000] TRAMPOLINE
[ 0.000000] #10 [0000008000 - 000000c000] PGTABLE
[ 0.000000] #11 [000000c000 - 000000d000] PGTABLE
[ 0.000000] #12 [000000d000 - 000000f440] MEMNODEMAP
[ 0.000000] [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff880028600000-ffff88002a1fffff] on node 0
[ 0.000000] [ffffea0001c00000-ffffea0003ffffff] PMD -> [ffff880080200000-ffff880081ffffff] on node 1
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00120000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[4] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x00080000
[ 0.000000] 1: 0x00080000 -> 0x000dffd0
[ 0.000000] 1: 0x00100000 -> 0x00120000
[ 0.000000] On node 0 totalpages: 524191
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 104 pages reserved
[ 0.000000] DMA zone: 3839 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7112 pages used for memmap
[ 0.000000] DMA32 zone: 513080 pages, LIFO batch:31
[ 0.000000] On node 1 totalpages: 524240
[ 0.000000] DMA32 zone: 7168 pages used for memmap
[ 0.000000] DMA32 zone: 386000 pages, LIFO batch:31
[ 0.000000] Normal zone: 1792 pages used for memmap
[ 0.000000] Normal zone: 129280 pages, LIFO batch:31
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] ACPI: PM-Timer IO Port: 0x2008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] Allocating PCI resources starting at e0000000 (gap: e0000000:1ec00000)
[ 0.000000] setup_percpu: NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:2
[ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff880028200000 s78488 r8192 d23912 u1048576
[ 0.000000] pcpu-alloc: s78488 r8192 d23912 u1048576 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 [1] 2 3
[ 0.000000] Built 2 zonelists in Node order, mobility grouping on. Total pages: 1032199
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: fastboot earlyprintk=serial,ttyS0,115200 console=ttyS0,115200 console=tty1 crypt_root=/dev/md3 radeon.modeset=1
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Node 0: aperture @ 20000000 size 32 MB
[ 0.000000] Aperture pointing to e820 RAM. Ignoring.
[ 0.000000] Your BIOS doesn't leave a aperture memory hole
[ 0.000000] Please enable the IOMMU option in the BIOS setup
[ 0.000000] This costs you 64 MB of RAM
[ 0.000000] Mapping aperture over 65536 KB of RAM @ 20000000
[ 0.000000] Memory: 3990564k/4718592k available (5263k kernel code, 524868k absent, 203160k reserved, 3084k data, 1216k init)
[ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=2
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is enabled.
[ 0.000000] NR_IRQS:4352 nr_irqs:440
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty1] enabled, bootconsole disabled
[ 0.000000] console [ttyS0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2599.982 MHz processor.
[ 0.020004] Calibrating delay loop (skipped), value calculated using timer frequency.. 5199.96 BogoMIPS (lpj=25999820)
[ 0.030032] Security Framework initialized
[ 0.034385] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.042636] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.051169] Mount-cache hash table entries: 256
[ 0.055844] tseg: 0000000000
[ 0.055854] CPU: Physical Processor ID: 0
[ 0.060003] CPU: Processor Core ID: 0
[ 0.063669] mce: CPU supports 5 MCE banks
[ 0.067688] using C1E aware idle routine
[ 0.070001] Performance Events: AMD PMU driver.
[ 0.074562] ... version: 0
[ 0.080001] ... bit width: 48
[ 0.084103] ... generic registers: 4
[ 0.090001] ... value mask: 0000ffffffffffff
[ 0.095313] ... max period: 00007fffffffffff
[ 0.100001] ... fixed-purpose events: 0
[ 0.104016] ... event mask: 000000000000000f
[ 0.110011] Freeing SMP alternatives: 34k freed
[ 0.114562] ACPI: Core revision 20091214
[ 0.127992] Setting APIC routing to flat
[ 0.130427] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.238384] CPU0: Dual-Core AMD Opteron(tm) Processor 2218 stepping 02
[ 0.250000] Booting Node 0, Processors #1 Ok.
[ 0.400648] Booting Node 1, Processors #2 #3 Ok.
[ 0.720032] Brought up 4 CPUs
[ 0.723013] Total of 4 processors activated (20800.09 BogoMIPS).
[ 0.730081] NET: Registered protocol family 16
[ 0.734552] node 0 link 0: io port [3000, ffffff]
[ 0.734552] node 0 link 0: io port [2000, 2fff]
[ 0.734552] TOM: 00000000e0000000 aka 3584M
[ 0.734552] node 0 link 0: mmio [f0000000, f3ffffff]
[ 0.734552] node 0 link 0: mmio [a0000, bffff]
[ 0.734552] node 0 link 0: mmio [e0000000, efffffff]
[ 0.734552] TOM2: 0000000120000000 aka 4608M
[ 0.740002] bus: [00, ff] on node 0 link 0
[ 0.740004] bus: 00 index 0 io port: [0, ffff]
[ 0.740005] bus: 00 index 1 mmio: [e0000000, ffffffff]
[ 0.740006] bus: 00 index 2 mmio: [a0000, bffff]
[ 0.740008] bus: 00 index 3 mmio: [120000000, fcffffffff]
[ 0.740014] ACPI: bus type pci registered
[ 0.744048] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xf0000000-0xffffffff] (base 0xf0000000)
[ 0.750002] PCI: not using MMCONFIG
[ 0.760002] PCI: Using configuration type 1 for base access
[ 0.770052] bio: create slab <bio-0> at 0
[ 0.780734] ACPI: EC: Look up EC in DSDT
[ 0.784036] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.796957] ACPI: Interpreter enabled
[ 0.800002] ACPI: (supports S0 S5)
[ 0.803475] ACPI: Using IOAPIC for interrupt routing
[ 0.808495] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xf0000000-0xffffffff] (base 0xf0000000)
[ 0.846386] [Firmware Bug]: PCI: MMCONFIG at [mem 0xf0000000-0xffffffff] not reserved in ACPI motherboard resources
[ 0.850001] PCI: not using MMCONFIG
[ 0.870143] ACPI Warning: Incorrect checksum in table [OEMB] - EC, should be E7 (20091214/tbutils-314)
[ 0.880163] ACPI: No dock devices found.
[ 0.884342] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.889168] pci_root PNP0A03:00: ignoring host bridge windows from ACPI; boot with "pci=use_crs" to use them
[ 0.890199] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.890201] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.890203] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.890205] pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff] (ignored)
[ 0.890207] pci_root PNP0A03:00: host bridge window [mem 0xe0000000-0xfebfffff] (ignored)
[ 0.890347] pci 0000:00:01.0: reg 10: [io 0x2f00-0x2f7f]
[ 0.890374] pci 0000:00:01.1: reg 10: [io 0xa880-0xa8bf]
[ 0.890383] pci 0000:00:01.1: reg 20: [io 0x2a00-0x2a3f]
[ 0.890387] pci 0000:00:01.1: reg 24: [io 0x2a80-0x2abf]
[ 0.890405] pci 0000:00:01.1: PME# supported from D3hot D3cold
[ 0.890409] pci 0000:00:01.1: PME# disabled
[ 0.890428] pci 0000:00:02.0: reg 10: [mem 0xefaf8000-0xefaf8fff]
[ 0.890444] pci 0000:00:02.0: supports D1 D2
[ 0.890446] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.890448] pci 0000:00:02.0: PME# disabled
[ 0.890461] pci 0000:00:02.1: reg 10: [mem 0xefaebc00-0xefaebcff]
[ 0.890477] pci 0000:00:02.1: supports D1 D2
[ 0.890478] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.890480] pci 0000:00:02.1: PME# disabled
[ 0.890500] pci 0000:00:04.0: reg 20: [io 0xffa0-0xffaf]
[ 0.890520] pci 0000:00:05.0: reg 10: [io 0xcc00-0xcc07]
[ 0.890523] pci 0000:00:05.0: reg 14: [io 0xc880-0xc883]
[ 0.890526] pci 0000:00:05.0: reg 18: [io 0xc800-0xc807]
[ 0.890528] pci 0000:00:05.0: reg 1c: [io 0xc480-0xc483]
[ 0.890531] pci 0000:00:05.0: reg 20: [io 0xc400-0xc40f]
[ 0.890534] pci 0000:00:05.0: reg 24: [mem 0xefafb000-0xefafbfff]
[ 0.890556] pci 0000:00:05.1: reg 10: [io 0xc080-0xc087]
[ 0.890559] pci 0000:00:05.1: reg 14: [io 0xc000-0xc003]
[ 0.890561] pci 0000:00:05.1: reg 18: [io 0xbc00-0xbc07]
[ 0.890564] pci 0000:00:05.1: reg 1c: [io 0xb880-0xb883]
[ 0.890567] pci 0000:00:05.1: reg 20: [io 0xb800-0xb80f]
[ 0.890569] pci 0000:00:05.1: reg 24: [mem 0xefafa000-0xefafafff]
[ 0.890591] pci 0000:00:05.2: reg 10: [io 0xb480-0xb487]
[ 0.890594] pci 0000:00:05.2: reg 14: [io 0xb400-0xb403]
[ 0.890597] pci 0000:00:05.2: reg 18: [io 0xb080-0xb087]
[ 0.890599] pci 0000:00:05.2: reg 1c: [io 0xb000-0xb003]
[ 0.890602] pci 0000:00:05.2: reg 20: [io 0xac00-0xac0f]
[ 0.890605] pci 0000:00:05.2: reg 24: [mem 0xefaf9000-0xefaf9fff]
[ 0.890651] pci 0000:00:06.1: reg 10: [mem 0xefafc000-0xefafffff]
[ 0.890670] pci 0000:00:06.1: PME# supported from D3hot D3cold
[ 0.890672] pci 0000:00:06.1: PME# disabled
[ 0.900013] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.900015] pci 0000:00:0b.0: PME# disabled
[ 0.900037] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.900039] pci 0000:00:0c.0: PME# disabled
[ 0.900061] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.900063] pci 0000:00:0d.0: PME# disabled
[ 0.900085] pci 0000:00:0f.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.900087] pci 0000:00:0f.0: PME# disabled
[ 0.900219] pci 0000:05:06.0: reg 10: [mem 0xeefff000-0xeeffffff pref]
[ 0.900261] pci 0000:05:06.1: reg 10: [mem 0xeeffe000-0xeeffefff pref]
[ 0.900308] pci 0000:05:08.0: reg 10: [mem 0xeffff800-0xefffffff]
[ 0.900313] pci 0000:05:08.0: reg 14: [mem 0xefff8000-0xefffbfff]
[ 0.900335] pci 0000:05:08.0: supports D1 D2
[ 0.900337] pci 0000:05:08.0: PME# supported from D0 D1 D2 D3hot
[ 0.900339] pci 0000:05:08.0: PME# disabled
[ 0.900359] pci 0000:00:06.0: PCI bridge to [bus 05-05] (subtractive decode)
[ 0.907405] pci 0000:00:06.0: bridge window [mem 0xeff00000-0xefffffff]
[ 0.907408] pci 0000:00:06.0: bridge window [mem 0xeef00000-0xeeffffff pref]
[ 0.907443] pci 0000:04:00.0: reg 10: [mem 0xefeffc00-0xefeffc7f 64bit]
[ 0.907456] pci 0000:04:00.0: reg 18: [mem 0xefef8000-0xefefbfff 64bit]
[ 0.907463] pci 0000:04:00.0: reg 20: [io 0xec00-0xec7f]
[ 0.907476] pci 0000:04:00.0: reg 30: [mem 0xefe00000-0xefe7ffff pref]
[ 0.907507] pci 0000:04:00.0: supports D1 D2
[ 0.907522] pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.910028] pci 0000:00:0b.0: PCI bridge to [bus 04-04]
[ 0.920004] pci 0000:00:0b.0: bridge window [io 0xe000-0xefff]
[ 0.920006] pci 0000:00:0b.0: bridge window [mem 0xefe00000-0xefefffff]
[ 0.920035] pci 0000:03:00.0: reg 10: [mem 0xefdf0000-0xefdfffff 64bit]
[ 0.920080] pci 0000:03:00.0: PME# supported from D3hot D3cold
[ 0.920083] pci 0000:03:00.0: PME# disabled
[ 0.940029] pci 0000:00:0c.0: PCI bridge to [bus 03-03]
[ 0.945258] pci 0000:00:0c.0: bridge window [mem 0xefd00000-0xefdfffff]
[ 0.945290] pci 0000:02:00.0: reg 10: [mem 0xefcf0000-0xefcfffff 64bit]
[ 0.945335] pci 0000:02:00.0: PME# supported from D3hot D3cold
[ 0.945338] pci 0000:02:00.0: PME# disabled
[ 0.960030] pci 0000:00:0d.0: PCI bridge to [bus 02-02]
[ 0.965260] pci 0000:00:0d.0: bridge window [mem 0xefc00000-0xefcfffff]
[ 0.965276] pci 0000:01:00.0: reg 10: [mem 0xe0000000-0xe7ffffff pref]
[ 0.965280] pci 0000:01:00.0: reg 14: [io 0xd000-0xd0ff]
[ 0.965284] pci 0000:01:00.0: reg 18: [mem 0xefbf0000-0xefbfffff]
[ 0.965294] pci 0000:01:00.0: reg 30: [mem 0xefbc0000-0xefbdffff pref]
[ 0.965306] pci 0000:01:00.0: supports D1 D2
[ 0.965322] pci 0000:01:00.1: reg 10: [mem 0xefbe0000-0xefbeffff]
[ 0.965346] pci 0000:01:00.1: supports D1 D2
[ 0.965355] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.970028] pci 0000:00:0f.0: PCI bridge to [bus 01-01]
[ 0.980002] pci 0000:00:0f.0: bridge window [io 0xd000-0xdfff]
[ 0.980004] pci 0000:00:0f.0: bridge window [mem 0xefb00000-0xefbfffff]
[ 0.980007] pci 0000:00:0f.0: bridge window [mem 0xe0000000-0xe7ffffff 64bit pref]
[ 0.980017] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.980219] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.980274] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[ 0.980325] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 0.980366] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
[ 0.980407] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
[ 0.990159] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *11
[ 0.996744] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
[ 1.002943] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *10
[ 1.011170] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
[ 1.018641] ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *10
[ 1.022046] ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *10
[ 1.031749] ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, disabled.
[ 1.039221] ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *5
[ 1.041957] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *10
[ 1.052043] ACPI: PCI Interrupt Link [LMAD] (IRQs 20 21 22 23) *0, disabled.
[ 1.060132] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *11
[ 1.066723] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled.
[ 1.072952] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *11
[ 1.080757] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11
[ 1.087329] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *5
[ 1.091966] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *5
[ 1.100374] ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *10
[ 1.106983] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
[ 1.112954] ACPI: PCI Interrupt Link [LSA2] (IRQs 20 21 22 23) *10
[ 1.121047] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 1.128105] vgaarb: loaded
[ 1.130061] SCSI subsystem initialized
[ 1.133821] libata version 3.00 loaded.
[ 1.133838] usbcore: registered new interface driver usbfs
[ 1.140023] usbcore: registered new interface driver hub
[ 1.145346] usbcore: registered new device driver usb
[ 1.150033] PCI: Using ACPI for IRQ routing
[ 1.154197] PCI: pci_cache_line_size set to 64 bytes
[ 1.154290] NetLabel: Initializing
[ 1.160001] NetLabel: domain hash size = 128
[ 1.164355] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.169332] NetLabel: unlabeled traffic allowed by default
[ 1.170004] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 1.180005] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[ 1.185103] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[ 1.210006] Switching to clocksource hpet
[ 1.214110] Slow work thread pool: Starting up
[ 1.214678] Slow work thread pool: Ready
[ 1.218661] FS-Cache: Loaded
[ 1.221645] CacheFiles: Loaded
[ 1.224733] pnp: PnP ACPI init
[ 1.227803] ACPI: bus type pnp registered
[ 1.236982] pnp: PnP ACPI: found 14 devices
[ 1.241176] ACPI: ACPI bus type pnp unregistered
[ 1.245845] system 00:06: [io 0x04d0-0x04d1] has been reserved
[ 1.251762] system 00:06: [io 0x07b0-0x07df] has been reserved
[ 1.257718] system 00:06: [io 0x0800-0x080f] has been reserved
[ 1.263654] system 00:06: [io 0x0bb0-0x0bdf] has been reserved
[ 1.269573] system 00:06: [io 0x2000-0x207f] has been reserved
[ 1.275527] system 00:06: [io 0x2080-0x20ff] has been reserved
[ 1.281446] system 00:06: [io 0x2400-0x247f] has been reserved
[ 1.287400] system 00:06: [io 0x2480-0x24ff] has been reserved
[ 1.293339] system 00:06: [io 0x2800-0x287f] has been reserved
[ 1.299256] system 00:06: [io 0x2880-0x28ff] has been reserved
[ 1.305316] system 00:06: [io 0x2c00-0x2c7f] has been reserved
[ 1.311234] system 00:06: [io 0x2c80-0x2cff] has been reserved
[ 1.317189] system 00:06: [mem 0xfee01000-0xfeefffff] has been reserved
[ 1.323820] system 00:06: [mem 0xefa80000-0xefabffff] has been reserved
[ 1.330437] system 00:06: [mem 0xffb00000-0xffbfffff] has been reserved
[ 1.337087] system 00:06: [mem 0xfff00000-0xffffffff] has been reserved
[ 1.343720] system 00:08: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 1.350682] system 00:08: [mem 0xfee00000-0xfee00fff] has been reserved
[ 1.357335] system 00:0c: [io 0x0290-0x0297] has been reserved
[ 1.363280] system 00:0d: [mem 0x00000000-0x0009ffff] could not be reserved
[ 1.370424] system 00:0d: [mem 0x000c0000-0x000cffff] has been reserved
[ 1.377075] system 00:0d: [mem 0x000e0000-0x000fffff] could not be reserved
[ 1.384052] system 00:0d: [mem 0x00100000-0xdfffffff] could not be reserved
[ 1.391009] system 00:0d: [mem 0xfec00000-0xffffffff] could not be reserved
[ 1.403570] pci 0000:00:06.0: PCI bridge to [bus 05-05]
[ 1.408802] pci 0000:00:06.0: bridge window [io disabled]
[ 1.414499] pci 0000:00:06.0: bridge window [mem 0xeff00000-0xefffffff]
[ 1.421289] pci 0000:00:06.0: bridge window [mem 0xeef00000-0xeeffffff pref]
[ 1.428730] pci 0000:00:0b.0: PCI bridge to [bus 04-04]
[ 1.433971] pci 0000:00:0b.0: bridge window [io 0xe000-0xefff]
[ 1.440063] pci 0000:00:0b.0: bridge window [mem 0xefe00000-0xefefffff]
[ 1.446885] pci 0000:00:0b.0: bridge window [mem pref disabled]
[ 1.452995] pci 0000:00:0c.0: PCI bridge to [bus 03-03]
[ 1.458220] pci 0000:00:0c.0: bridge window [io disabled]
[ 1.463907] pci 0000:00:0c.0: bridge window [mem 0xefd00000-0xefdfffff]
[ 1.470689] pci 0000:00:0c.0: bridge window [mem pref disabled]
[ 1.476821] pci 0000:00:0d.0: PCI bridge to [bus 02-02]
[ 1.482046] pci 0000:00:0d.0: bridge window [io disabled]
[ 1.487740] pci 0000:00:0d.0: bridge window [mem 0xefc00000-0xefcfffff]
[ 1.496545] pci 0000:00:0d.0: bridge window [mem pref disabled]
[ 1.502655] pci 0000:00:0f.0: PCI bridge to [bus 01-01]
[ 1.507883] pci 0000:00:0f.0: bridge window [io 0xd000-0xdfff]
[ 1.514009] pci 0000:00:0f.0: bridge window [mem 0xefb00000-0xefbfffff]
[ 1.520791] pci 0000:00:0f.0: bridge window [mem 0xe0000000-0xe7ffffff 64bit pref]
[ 1.528577] pci 0000:00:06.0: setting latency timer to 64
[ 1.528582] pci 0000:00:0b.0: setting latency timer to 64
[ 1.528586] pci 0000:00:0c.0: setting latency timer to 64
[ 1.528590] pci 0000:00:0d.0: setting latency timer to 64
[ 1.528594] pci 0000:00:0f.0: setting latency timer to 64
[ 1.528597] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 1.528599] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffffffffffff]
[ 1.528601] pci_bus 0000:05: resource 1 [mem 0xeff00000-0xefffffff]
[ 1.528603] pci_bus 0000:05: resource 2 [mem 0xeef00000-0xeeffffff pref]
[ 1.528604] pci_bus 0000:05: resource 3 [io 0x0000-0xffff]
[ 1.528606] pci_bus 0000:05: resource 4 [mem 0x00000000-0xffffffffffffffff]
[ 1.528608] pci_bus 0000:04: resource 0 [io 0xe000-0xefff]
[ 1.528610] pci_bus 0000:04: resource 1 [mem 0xefe00000-0xefefffff]
[ 1.528612] pci_bus 0000:03: resource 1 [mem 0xefd00000-0xefdfffff]
[ 1.528614] pci_bus 0000:02: resource 1 [mem 0xefc00000-0xefcfffff]
[ 1.528615] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff]
[ 1.528617] pci_bus 0000:01: resource 1 [mem 0xefb00000-0xefbfffff]
[ 1.528619] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xe7ffffff 64bit pref]
[ 1.528653] NET: Registered protocol family 2
[ 1.533173] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 1.541877] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 1.554162] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 1.561585] TCP: Hash tables configured (established 524288 bind 65536)
[ 1.568241] TCP reno registered
[ 1.571411] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 1.577488] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 1.584082] NET: Registered protocol family 1
[ 1.588622] RPC: Registered udp transport module.
[ 1.593354] RPC: Registered tcp transport module.
[ 1.598066] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.640096] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 1.645643] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 1.651174] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 1.656738] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 1.662269] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 1.667837] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 1.673397] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 1.678939] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 1.684515] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 1.690031] pci 0000:01:00.0: Boot video device
[ 1.690035] PCI: CLS 64 bytes, default 64
[ 1.690093] Unpacking initramfs...
[ 1.714630] Freeing initrd memory: 1183k freed
[ 1.725340] DMA-API: preallocated 32768 debug entries
[ 1.730399] DMA-API: debugging enabled by kernel config
[ 1.735707] PCI-DMA: Disabling AGP.
[ 1.739428] PCI-DMA: aperture base @ 20000000 size 65536 KB
[ 1.745036] PCI-DMA: using GART IOMMU.
[ 1.748795] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 1.761274] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.771182] VFS: Disk quotas dquot_6.5.2
[ 1.775211] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.781844] FS-Cache: Netfs 'nfs' registered for caching
[ 1.787450] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[ 1.797033] SGI XFS Quota Management subsystem
[ 1.801490] msgmni has been set to 7925
[ 1.806258] alg: No test for stdrng (krng)
[ 1.814654] alg: No test for fips(ansi_cprng) (fips_ansi_cprng)
[ 1.820726] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 1.828141] io scheduler noop registered
[ 1.832151] io scheduler cfq registered (default)
[ 1.837035] pcieport 0000:00:0b.0: setting latency timer to 64
[ 1.837051] alloc irq_desc for 24 on node 0
[ 1.837056] alloc kstat_irqs on node 0
[ 1.837064] pcieport 0000:00:0b.0: irq 24 for MSI/MSI-X
[ 1.837178] pcieport 0000:00:0c.0: setting latency timer to 64
[ 1.837189] alloc irq_desc for 25 on node 0
[ 1.837191] alloc kstat_irqs on node 0
[ 1.837194] pcieport 0000:00:0c.0: irq 25 for MSI/MSI-X
[ 1.837284] pcieport 0000:00:0d.0: setting latency timer to 64
[ 1.837296] alloc irq_desc for 26 on node 0
[ 1.837297] alloc kstat_irqs on node 0
[ 1.837301] pcieport 0000:00:0d.0: irq 26 for MSI/MSI-X
[ 1.837392] pcieport 0000:00:0f.0: setting latency timer to 64
[ 1.837404] alloc irq_desc for 27 on node 0
[ 1.837405] alloc kstat_irqs on node 0
[ 1.837408] pcieport 0000:00:0f.0: irq 27 for MSI/MSI-X
[ 1.837893] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 1.846270] ACPI: Power Button [PWRB]
[ 1.850040] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 1.857460] ACPI: Power Button [PWRF]
[ 1.865655] Real Time Clock Driver v1.12b
[ 1.869945] Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
[ 1.878919] Hangcheck: Using get_cycles().
[ 1.883094] [drm] Initialized drm 1.1.0 20060810
[ 1.887780] [drm] radeon kernel modesetting enabled.
[ 1.893156] ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 19
[ 1.898904] alloc irq_desc for 19 on node 0
[ 1.898906] alloc kstat_irqs on node 0
[ 1.898914] radeon 0000:01:00.0: PCI INT A -> Link[LNEB] -> GSI 19 (level, low) -> IRQ 19
[ 1.907122] radeon 0000:01:00.0: setting latency timer to 64
[ 1.909341] [drm] radeon: Initializing kernel modesetting.
[ 1.914948] [drm] register mmio base: 0xEFBF0000
[ 1.919566] [drm] register mmio size: 65536
[ 1.924449] [drm] GPU reset succeed (RBBM_STATUS=0x00000140)
[ 1.930151] [drm] Generation 2 PCI interface, using max accessible memory
[ 1.936939] [drm] radeon: VRAM 128M
[ 1.941039] [drm] radeon: VRAM from 0x00000000 to 0x07FFFFFF
[ 1.946698] [drm] radeon: GTT 512M
[ 1.950132] [drm] radeon: GTT from 0x20000000 to 0x3FFFFFFF
[ 1.955725] alloc irq_desc for 28 on node 0
[ 1.955726] alloc kstat_irqs on node 0
[ 1.955734] radeon 0000:01:00.0: irq 28 for MSI/MSI-X
[ 1.955738] [drm] radeon: using MSI.
[ 1.959340] [drm] radeon: irq initialized.
[ 1.964162] [drm] Detected VRAM RAM=128M, BAR=128M
[ 1.968965] [drm] RAM width 64bits DDR
[ 1.972807] [TTM] Zone kernel: Available graphics memory: 2028868 kiB.
[ 1.979427] [drm] radeon: 128M of VRAM memory ready
[ 1.984339] [drm] radeon: 512M of GTT memory ready.
[ 1.989232] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 1.996445] [drm] radeon: 1 quad pipes, 1 Z pipes initialized.
[ 2.002352] [drm] PCIE GART of 512M enabled (table at 0x00040000).
[ 2.008533] [drm] radeon: cp idle (0x10000C03)
[ 2.013133] [drm] Loading R300 Microcode
[ 2.017060] platform radeon_cp.0: firmware: using built-in firmware radeon/R300_cp.bin
[ 2.026080] [drm] radeon: ring at 0x0000000020000000
[ 2.031079] [drm] ring test succeeded in 1 usecs
[ 2.036711] [drm] radeon: ib pool ready.
[ 2.040726] [drm] ib test succeeded in 0 usecs
[ 2.045370] [drm] Default TV standard: NTSC
[ 2.049560] [drm] 27.000000000 MHz TV ref clk
[ 2.053946] [drm] DFP table revision: 4
[ 2.058006] [drm] Radeon Display Connectors
[ 2.062209] [drm] Connector 0:
[ 2.065273] [drm] VGA
[ 2.067731] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[ 2.073766] [drm] Encoders:
[ 2.076740] [drm] CRT1: INTERNAL_DAC1
[ 2.080772] [drm] Connector 1:
[ 2.083837] [drm] DVI-I
[ 2.086466] [drm] HPD1
[ 2.089008] [drm] DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[ 2.095046] [drm] Encoders:
[ 2.098025] [drm] CRT2: INTERNAL_DAC2
[ 2.102058] [drm] DFP1: INTERNAL_TMDS1
[ 2.106161] [drm] Connector 2:
[ 2.109221] [drm] S-video
[ 2.112051] [drm] Encoders:
[ 2.115029] [drm] TV1: INTERNAL_DAC2
[ 2.343970] [drm] fb mappable at 0xE00C0000
[ 2.348160] [drm] vram apper at 0xE0000000
[ 2.352291] [drm] size 5242880
[ 2.355356] [drm] fb depth is 24
[ 2.358590] [drm] pitch is 5120
[ 2.413116] [drm] DAC-9: set mode 1280x1024 2d
[ 2.463375] [drm] TMDS-12: set mode 1280x1024 32
[ 2.473694] Console: switching to colour frame buffer device 160x64
[ 2.493930] fb0: radeondrmfb frame buffer device
[ 2.498559] registered panic notifier
[ 2.502261] [drm] Initialized radeon 2.0.0 20080528 for 0000:01:00.0 on minor 0
[ 2.509735] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 2.516301] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.522683] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.528737] sata_sil24 0000:04:00.0: version 1.1
[ 2.528758] sata_sil24 0000:04:00.0: PCI INT A -> Link[LNEB] -> GSI 19 (level, low) -> IRQ 19
[ 2.537392] sata_sil24 0000:04:00.0: setting latency timer to 64
[ 2.537607] scsi0 : sata_sil24
[ 2.540841] scsi1 : sata_sil24
[ 2.544007] ata1: SATA max UDMA/100 host m128@0xefeffc00 port 0xefef8000 irq 19
[ 2.551357] ata2: SATA max UDMA/100 host m128@0xefeffc00 port 0xefefa000 irq 19
[ 2.558807] sata_nv 0000:00:05.0: version 3.5
[ 2.559095] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
[ 2.564880] alloc irq_desc for 23 on node 0
[ 2.564881] alloc kstat_irqs on node 0
[ 2.564890] sata_nv 0000:00:05.0: PCI INT A -> Link[LSA0] -> GSI 23 (level, low) -> IRQ 23
[ 2.573203] sata_nv 0000:00:05.0: Using SWNCQ mode
[ 2.578042] sata_nv 0000:00:05.0: setting latency timer to 64
[ 2.578163] scsi2 : sata_nv
[ 2.581173] scsi3 : sata_nv
[ 2.584187] ata3: SATA max UDMA/133 cmd 0xcc00 ctl 0xc880 bmdma 0xc400 irq 23
[ 2.591371] ata4: SATA max UDMA/133 cmd 0xc800 ctl 0xc480 bmdma 0xc408 irq 23
[ 2.598810] ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 22
[ 2.604612] alloc irq_desc for 22 on node 0
[ 2.604614] alloc kstat_irqs on node 0
[ 2.604620] sata_nv 0000:00:05.1: PCI INT B -> Link[LSA1] -> GSI 22 (level, low) -> IRQ 22
[ 2.612932] sata_nv 0000:00:05.1: Using SWNCQ mode
[ 2.617771] sata_nv 0000:00:05.1: setting latency timer to 64
[ 2.617891] scsi4 : sata_nv
[ 2.620857] scsi5 : sata_nv
[ 2.623866] ata5: SATA max UDMA/133 cmd 0xc080 ctl 0xc000 bmdma 0xb800 irq 22
[ 2.631046] ata6: SATA max UDMA/133 cmd 0xbc00 ctl 0xb880 bmdma 0xb808 irq 22
[ 2.638514] ACPI: PCI Interrupt Link [LSA2] enabled at IRQ 21
[ 2.644302] alloc irq_desc for 21 on node 0
[ 2.644303] alloc kstat_irqs on node 0
[ 2.644310] sata_nv 0000:00:05.2: PCI INT C -> Link[LSA2] -> GSI 21 (level, low) -> IRQ 21
[ 2.652625] sata_nv 0000:00:05.2: Using SWNCQ mode
[ 2.657453] sata_nv 0000:00:05.2: setting latency timer to 64
[ 2.657572] scsi6 : sata_nv
[ 2.660537] scsi7 : sata_nv
[ 2.663541] ata7: SATA max UDMA/133 cmd 0xb480 ctl 0xb400 bmdma 0xac00 irq 21
[ 2.670724] ata8: SATA max UDMA/133 cmd 0xb080 ctl 0xb000 bmdma 0xac08 irq 21
[ 2.678041] pata_amd 0000:00:04.0: version 0.4.1
[ 2.678068] pata_amd 0000:00:04.0: setting latency timer to 64
[ 2.678126] scsi8 : pata_amd
[ 2.681166] scsi9 : pata_amd
[ 2.685030] ata9: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 2.692036] ata10: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 2.699317] tg3.c:v3.105 (December 2, 2009)
[ 2.704894] ACPI: PCI Interrupt Link [LNEA] enabled at IRQ 18
[ 2.711810] alloc irq_desc for 18 on node 0
[ 2.711812] alloc kstat_irqs on node 0
[ 2.711819] tg3 0000:03:00.0: PCI INT A -> Link[LNEA] -> GSI 18 (level, low) -> IRQ 18
[ 2.720957] tg3 0000:03:00.0: setting latency timer to 64
[ 2.764289] eth0: Tigon3 [partno(BCM95700A6) rev b002] (PCI Express) MAC address 00:17:31:f9:cc:c5
[ 2.774520] eth0: attached PHY is 5787 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[ 2.783387] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 2.791067] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 2.797928] ACPI: PCI Interrupt Link [LNED] enabled at IRQ 17
[ 2.805056] alloc irq_desc for 17 on node 0
[ 2.805058] alloc kstat_irqs on node 0
[ 2.805064] tg3 0000:02:00.0: PCI INT A -> Link[LNED] -> GSI 17 (level, low) -> IRQ 17
[ 2.814410] tg3 0000:02:00.0: setting latency timer to 64
[ 2.865115] eth1: Tigon3 [partno(BCM95700A6) rev b002] (PCI Express) MAC address 00:18:f3:44:df:ea
[ 2.875551] eth1: attached PHY is 5787 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[ 2.884634] eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 2.892530] eth1: dma_rwctrl[76180000] dma_mask[64-bit]
[ 2.899647] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 16
[ 2.906985] alloc irq_desc for 16 on node 0
[ 2.906986] alloc kstat_irqs on node 0
[ 2.906992] ohci1394 0000:05:08.0: PCI INT A -> Link[LNKA] -> GSI 16 (level, low) -> IRQ 16
[ 2.970045] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[effff800-efffffff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 2.971557] ata5: SATA link down (SStatus 0 SControl 300)
[ 2.990775] eth1394: eth2: IPv4 over IEEE 1394 (fw-host0)
[ 2.998153] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.006750] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 20
[ 3.014350] alloc irq_desc for 20 on node 0
[ 3.014351] alloc kstat_irqs on node 0
[ 3.014358] ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUB2] -> GSI 20 (level, low) -> IRQ 20
[ 3.024584] ehci_hcd 0000:00:02.1: setting latency timer to 64
[ 3.024587] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 3.031669] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[ 3.031927] ata7: SATA link down (SStatus 0 SControl 300)
[ 3.048193] ehci_hcd 0000:00:02.1: debug port 1
[ 3.054574] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
[ 3.054591] ehci_hcd 0000:00:02.1: irq 20, io mem 0xefaebc00
[ 3.080012] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
[ 3.081279] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.095578] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.104177] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.113202] usb usb1: Product: EHCI Host Controller
[ 3.119868] usb usb1: Manufacturer: Linux 2.6.33-rc1 ehci_hcd
[ 3.127429] usb usb1: SerialNumber: 0000:00:02.1
[ 3.134016] hub 1-0:1.0: USB hub found
[ 3.139548] hub 1-0:1.0: 10 ports detected
[ 3.145508] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.153536] ata3.00: ATA-7: MAXTOR STM3320820AS, 3.AAE, max UDMA/133
[ 3.153751] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23
[ 3.153754] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUB0] -> GSI 23 (level, low) -> IRQ 23
[ 3.153763] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 3.153765] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 3.153772] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[ 3.153788] ohci_hcd 0000:00:02.0: irq 23, io mem 0xefaf8000
[ 3.203025] ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 3.212029] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.220658] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.229688] usb usb2: Product: OHCI Host Controller
[ 3.236406] usb usb2: Manufacturer: Linux 2.6.33-rc1 ohci_hcd
[ 3.243990] usb usb2: SerialNumber: 0000:00:02.0
[ 3.250565] hub 2-0:1.0: USB hub found
[ 3.256097] hub 2-0:1.0: 10 ports detected
[ 3.262072] Initializing USB Mass Storage driver...
[ 3.268824] usbcore: registered new interface driver usb-storage
[ 3.276644] USB Mass Storage support registered.
[ 3.278489] ata3.00: configured for UDMA/133
[ 3.289189] usbcore: registered new interface driver libusual
[ 3.296789] usbcore: registered new interface driver ums-alauda
[ 3.304564] usbcore: registered new interface driver ums-cypress
[ 3.312401] usbcore: registered new interface driver ums-datafab
[ 3.320222] usbcore: registered new interface driver ums-freecom
[ 3.328008] usbcore: registered new interface driver ums-isd200
[ 3.335686] usbcore: registered new interface driver ums-jumpshot
[ 3.343512] usbcore: registered new interface driver ums-karma
[ 3.351048] usbcore: registered new interface driver ums-sddr09
[ 3.358629] usbcore: registered new interface driver ums-sddr55
[ 3.366175] usbcore: registered new interface driver ums-usbat
[ 3.373669] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 3.384955] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.391477] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 3.398257] mice: PS/2 mouse device common for all mice
[ 3.405332] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 3.413492] I2O subsystem v1.325
[ 3.418215] i2o: max drivers = 8
[ 3.423231] i2c /dev entries driver
[ 3.425035] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 3.438645] i2c i2c-2: nForce2 SMBus adapter at 0x2a00
[ 3.445351] i2c i2c-3: nForce2 SMBus adapter at 0x2a80
[ 3.451980] Linux video capture interface: v2.00
[ 3.458435] bttv: driver version 0.9.18 loaded
[ 3.464284] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 3.472565] bttv: Bt8xx card found (0).
[ 3.478066] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 19
[ 3.485240] bttv 0000:05:06.0: PCI INT A -> Link[LNKC] -> GSI 19 (level, low) -> IRQ 19
[ 3.494658] bttv0: Bt878 (rev 17) at 0000:05:06.0, irq: 19, latency: 64, mmio: 0xeefff000
[ 3.504293] bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
[ 3.513576] bttv0: using: Hauppauge (bt878) [card=10,autodetected]
[ 3.521216] IRQ 19/bttv0: IRQF_DISABLED is not guaranteed on shared IRQs
[ 3.529382] bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
[ 3.531900] bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
[ 3.569216] tveeprom 4-0050: Hauppauge model 61344, rev D421, serial# 3902813
[ 3.577845] tveeprom 4-0050: tuner model is Philips FM1216 (idx 21, type 5)
[ 3.586278] tveeprom 4-0050: TV standards PAL(B/G) (eeprom 0x04)
[ 3.593758] tveeprom 4-0050: audio processor is MSP3415 (idx 6)
[ 3.601149] tveeprom 4-0050: has radio
[ 3.606342] bttv0: Hauppauge eeprom indicates model#61344
[ 3.613230] bttv0: tuner type=5
[ 3.628263] msp3400 4-0040: MSP3415D-B3 found @ 0x80 (bt878 #0 [sw])
[ 3.636127] msp3400 4-0040: msp3400 supports nicam, mode is autodetect
[ 3.656879] tuner 4-0061: chip found @ 0xc2 (bt878 #0 [sw])
[ 3.661293] usb 2-9: new low speed USB device using ohci_hcd and address 2
[ 3.672560] tuner-simple 4-0061: creating new instance
[ 3.679155] tuner-simple 4-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
[ 3.689423] bttv0: registered device video0
[ 3.695158] bttv0: registered device vbi0
[ 3.700675] bttv0: registered device radio0
[ 3.714787] bttv0: PLL: 28636363 => 35468950 .. ok
[ 3.752659] input: i2c IR (Hauppauge) as /devices/virtual/input/input4
[ 3.760746] ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-4/4-0018/ir0 [bt878 #0 [sw]]
[ 3.880044] usb 2-9: New USB device found, idVendor=062a, idProduct=0000
[ 3.888243] usb 2-9: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 4.310286] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d80000c4c261]
[ 4.613066] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[ 4.622902] k8temp 0000:00:19.3: Temperature readouts might be wrong - check erratum #141
[ 4.632720] md: raid1 personality registered for level 1
[ 4.639831] device-mapper: uevent: version 1.0.3
[ 4.646065] device-mapper: ioctl: 4.16.0-ioctl (2009-11-05) initialised: dm-devel@xxxxxxxxxx
[ 4.656095] EDAC MC: Ver: 2.1.0 Dec 20 2009
[ 4.661805] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661813] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661817] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661820] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661823] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661826] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661829] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661833] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661836] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661839] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661842] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661845] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661849] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661852] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661855] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661858] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661861] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661864] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661867] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661870] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661872] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661875] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661878] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661881] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661884] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661888] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661892] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661897] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661901] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661905] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661909] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 537: edac_pci_dev_parity_clear()
[ 4.661971] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 905: edac_sysfs_setup_mc_kset()
[ 4.662015] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 922: edac_sysfs_setup_mc_kset() Registered '.../edac/mc' kobject
[ 4.662042] EDAC amd64_edac: Ver: 3.3.0 Dec 20 2009
[ 4.668610] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2895: (MC node=0,mc_type='RevF')
[ 4.668625] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2261: Addr Map device PCI Bus ID: 0000:00:18.1
[ 4.668628] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2263: DRAM MEM-CTL PCI Bus ID: 0000:00:18.2
[ 4.668630] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2265: Misc device PCI Bus ID: 0000:00:18.3
[ 4.668632] EDAC amd64: ECC is enabled by BIOS.
[ 4.674755] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2519: core: 0, MCG_CTL: 0x1f, NB MSR is enabled
[ 4.674757] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2519: core: 1, MCG_CTL: 0x1f, NB MSR is enabled
[ 4.674796] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2895: (MC node=1,mc_type='RevF')
[ 4.674815] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2261: Addr Map device PCI Bus ID: 0000:00:19.1
[ 4.674817] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2263: DRAM MEM-CTL PCI Bus ID: 0000:00:19.2
[ 4.674819] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2265: Misc device PCI Bus ID: 0000:00:19.3
[ 4.674822] EDAC amd64: ECC is enabled by BIOS.
[ 4.680927] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2519: core: 2, MCG_CTL: 0x1f, NB MSR is enabled
[ 4.680929] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2519: core: 3, MCG_CTL: 0x1f, NB MSR is enabled
[ 4.681005] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2290: TOP_MEM: 0x00000000e0000000
[ 4.681008] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2296: TOP_MEM2: 0x0000000120000000
[ 4.681010] EDAC MC: Rev F or later detected
[ 4.681013] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2324: DRAM-BASE[0]: 0x0000000000000000 DRAM-LIMIT: 0x000000007fffffff
[ 4.681016] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2333: IntlvEn=Disabled W R IntlvSel=0 DstNode=0
[ 4.681019] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2324: DRAM-BASE[1]: 0x0000000080000000 DRAM-LIMIT: 0x000000011fffffff
[ 4.681022] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2333: IntlvEn=Disabled W R IntlvSel=0 DstNode=1
[ 4.681027] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[0]=0x00000001 reg: F2x40
[ 4.681029] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[1]=0x00000101 reg: F2x44
[ 4.681031] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[2]=0x00000000 reg: F2x48
[ 4.681033] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[3]=0x00000000 reg: F2x4c
[ 4.681036] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[4]=0x00000000 reg: F2x50
[ 4.681038] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[5]=0x00000000 reg: F2x54
[ 4.681040] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[6]=0x00000000 reg: F2x58
[ 4.681042] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[7]=0x00000000 reg: F2x5c
[ 4.681045] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 1002: DCSM0[0]=0x00783ee0 reg: F2x60
[ 4.681047] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 1002: DCSM0[1]=0x00000000 reg: F2x64
[ 4.681049] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 1002: DCSM0[2]=0x00000000 reg: F2x68
[ 4.681052] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 1002: DCSM0[3]=0x00000000 reg: F2x6c
[ 4.681056] EDAC amd64: amd64_read_mc_registers: error reading F2x190.
[ 4.689188] EDAC amd64: amd64_read_mc_registers: error reading F2x194.
[ 4.697301] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 862: F3xE8 (NB Cap): 0x0000171b
[ 4.697304] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 865: NB two channel DRAM capable: yes
[ 4.697306] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 869: ECC capable: yes, ChipKill ECC capable: yes
[ 4.697308] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 838: F2x090 (DRAM Cfg Low): 0x00080810
[ 4.697311] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 842: DIMM type: buffered; all DIMMs support ECC: yes
[ 4.697313] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 845: PAR/ERR parity: disabled
[ 4.697315] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 848: DCT 128bit mode width: 128b
[ 4.697317] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 854: x4 logical DIMMs present: L0: no L1: no L2: no L3: no
[ 4.697319] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 873: F3xB0 (Online Spare): 0x0f000000
[ 4.697322] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 880: F1xF0 (DRAM Hole Address): 0x00000000, base: 0x00000000, offset: 0x00000000
[ 4.697324] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 883: DramHoleValid: no
[ 4.697327] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 1716: F2x080 (DRAM Bank Address Mapping): 0x00000002
[ 4.697328] EDAC MC: DCT0 chip selects:
[ 4.697330] EDAC MC: 0: 512MB 1: 512MB
[ 4.697331] EDAC MC: 2: 0MB 3: 0MB
[ 4.697333] EDAC MC: 4: 0MB 5: 0MB
[ 4.697334] EDAC MC: 6: 0MB 7: 0MB
[ 4.697338] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 666: edac_mc_register_sysfs_main_kobj()
[ 4.697390] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 702: edac_mc_register_sysfs_main_kobj() Registered '.../edac/mc0' kobject
[ 4.697394] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2435: NBCFG= 0xa500040 CHIPKILL= Disabled DRAM ECC= Enabled
[ 4.697396] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2447: ----CSROW 0 VALID for MC node 0
[ 4.697398] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2410: (csrow=0) DBAM map index= 2
[ 4.697401] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2412: nr_pages= 262144 channel-count = 2
[ 4.697403] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 671: InputAddr 0x0 translates to DramAddr of same value
[ 4.697405] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 477: Dram Memory Hoisting is DISABLED on this node 0
[ 4.697408] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 732: Node 0, DramAddr 0x0 to SysAddr 0x0
[ 4.697410] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 671: InputAddr 0xffffffe07ffeffff translates to DramAddr of same value
[ 4.697413] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 477: Dram Memory Hoisting is DISABLED on this node 0
[ 4.697415] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 732: Node 0, DramAddr 0xffffffe07ffeffff to SysAddr 0xffffffe07ffeffff
[ 4.697418] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 1030: Memory type is: Registered DDR2 RAM
[ 4.697420] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2461: for MC node 0 csrow 0:
[ 4.697422] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2464: input_addr_min: 0x0 input_addr_max: 0xffffffe07ffeffff
[ 4.697424] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2466: sys_addr: 0xffffffe07ffeffff page_mask: 0x1f80010000
[ 4.697426] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2470: nr_pages: 262144 first_page: 0x0 last_page: 0xfe07ffef
[ 4.697429] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2447: ----CSROW 1 VALID for MC node 0
[ 4.697431] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2410: (csrow=1) DBAM map index= 2
[ 4.697433] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2412: nr_pages= 262144 channel-count = 2
[ 4.697435] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 671: InputAddr 0x10000 translates to DramAddr of same value
[ 4.697437] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 477: Dram Memory Hoisting is DISABLED on this node 0
[ 4.697439] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 732: Node 0, DramAddr 0x10000 to SysAddr 0x10000
[ 4.697441] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 671: InputAddr 0xffffffe07fffffff translates to DramAddr of same value
[ 4.697443] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 477: Dram Memory Hoisting is DISABLED on this node 0
[ 4.697446] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 732: Node 0, DramAddr 0xffffffe07fffffff to SysAddr 0xffffffe07fffffff
[ 4.697448] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 1030: Memory type is: Registered DDR2 RAM
[ 4.697450] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2461: for MC node 0 csrow 1:
[ 4.697452] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2464: input_addr_min: 0x10000 input_addr_max: 0xffffffe07fffffff
[ 4.697454] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2466: sys_addr: 0xffffffe07fffffff page_mask: 0x1f80010000
[ 4.697457] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2470: nr_pages: 262144 first_page: 0x10 last_page: 0xfe07ffff
[ 4.697459] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2442: ----CSROW 2 EMPTY for node 0
[ 4.697461] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2442: ----CSROW 3 EMPTY for node 0
[ 4.697463] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2442: ----CSROW 4 EMPTY for node 0
[ 4.697465] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2442: ----CSROW 5 EMPTY for node 0
[ 4.697467] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2442: ----CSROW 6 EMPTY for node 0
[ 4.697469] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2442: ----CSROW 7 EMPTY for node 0
[ 4.697472] EDAC DEBUG: in drivers/edac/edac_mc.c, line at 497: edac_mc_add_mc()
[ 4.697475] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 794: edac_create_sysfs_mci_device() idx=0
[ 4.697576] EDAC DEBUG: in drivers/edac/edac_mc.c, line at 320: edac_mc_workq_setup()
[ 4.697579] EDAC MC0: Giving out device to 'amd64_edac' 'RevF': DEV 0000:00:18.2
[ 4.706584] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2290: TOP_MEM: 0x00000000e0000000
[ 4.706586] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2296: TOP_MEM2: 0x0000000120000000
[ 4.706588] EDAC MC: Rev F or later detected
[ 4.706590] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2324: DRAM-BASE[0]: 0x0000000000000000 DRAM-LIMIT: 0x000000007fffffff
[ 4.706593] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2333: IntlvEn=Disabled W R IntlvSel=0 DstNode=0
[ 4.706596] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2324: DRAM-BASE[1]: 0x0000000080000000 DRAM-LIMIT: 0x000000011fffffff
[ 4.706598] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2333: IntlvEn=Disabled W R IntlvSel=0 DstNode=1
[ 4.706603] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[0]=0x00000001 reg: F2x40
[ 4.706605] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[1]=0x00000101 reg: F2x44
[ 4.706608] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[2]=0x00000000 reg: F2x48
[ 4.706610] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[3]=0x00000000 reg: F2x4c
[ 4.706612] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[4]=0x00000000 reg: F2x50
[ 4.706614] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[5]=0x00000000 reg: F2x54
[ 4.706616] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[6]=0x00000000 reg: F2x58
[ 4.706619] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 984: DCSB0[7]=0x00000000 reg: F2x5c
[ 4.706621] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 1002: DCSM0[0]=0x00783ee0 reg: F2x60
[ 4.706623] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 1002: DCSM0[1]=0x00000000 reg: F2x64
[ 4.706626] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 1002: DCSM0[2]=0x00000000 reg: F2x68
[ 4.706628] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 1002: DCSM0[3]=0x00000000 reg: F2x6c
[ 4.706631] EDAC amd64: amd64_read_mc_registers: error reading F2x190.
[ 4.714794] EDAC amd64: amd64_read_mc_registers: error reading F2x194.
[ 4.722931] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 862: F3xE8 (NB Cap): 0x0000171b
[ 4.722933] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 865: NB two channel DRAM capable: yes
[ 4.722935] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 869: ECC capable: yes, ChipKill ECC capable: yes
[ 4.722937] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 838: F2x090 (DRAM Cfg Low): 0x00080810
[ 4.722939] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 842: DIMM type: buffered; all DIMMs support ECC: yes
[ 4.722941] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 845: PAR/ERR parity: disabled
[ 4.722943] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 848: DCT 128bit mode width: 128b
[ 4.722945] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 854: x4 logical DIMMs present: L0: no L1: no L2: no L3: no
[ 4.722947] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 873: F3xB0 (Online Spare): 0x0f000000
[ 4.722949] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 880: F1xF0 (DRAM Hole Address): 0xe000a001, base: 0xe0000000, offset: 0xa0000000
[ 4.722952] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 883: DramHoleValid: yes
[ 4.722953] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 1716: F2x080 (DRAM Bank Address Mapping): 0x00000002
[ 4.722955] EDAC MC: DCT0 chip selects:
[ 4.722957] EDAC MC: 0: 512MB 1: 512MB
[ 4.722958] EDAC MC: 2: 0MB 3: 0MB
[ 4.722959] EDAC MC: 4: 0MB 5: 0MB
[ 4.722961] EDAC MC: 6: 0MB 7: 0MB
[ 4.722963] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 666: edac_mc_register_sysfs_main_kobj()
[ 4.723031] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 702: edac_mc_register_sysfs_main_kobj() Registered '.../edac/mc1' kobject
[ 4.723034] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2435: NBCFG= 0xa500040 CHIPKILL= Disabled DRAM ECC= Enabled
[ 4.723036] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2447: ----CSROW 0 VALID for MC node 1
[ 4.723038] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2410: (csrow=0) DBAM map index= 2
[ 4.723040] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2412: nr_pages= 262144 channel-count = 2
[ 4.723042] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 671: InputAddr 0x0 translates to DramAddr of same value
[ 4.723045] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 511: DHAR info for node 1 base 0xe0000000 offset 0xa0000000 size 0x20000000
[ 4.723048] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 732: Node 1, DramAddr 0x0 to SysAddr 0x80000000
[ 4.723050] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 671: InputAddr 0xffffffe07ffeffff translates to DramAddr of same value
[ 4.723052] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 511: DHAR info for node 1 base 0xe0000000 offset 0xa0000000 size 0x20000000
[ 4.723055] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 732: Node 1, DramAddr 0xffffffe07ffeffff to SysAddr 0xffffffe0fffeffff
[ 4.723057] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 1030: Memory type is: Registered DDR2 RAM
[ 4.723059] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2461: for MC node 1 csrow 0:
[ 4.723061] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2464: input_addr_min: 0x0 input_addr_max: 0xffffffe07ffeffff
[ 4.723063] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2466: sys_addr: 0xffffffe0fffeffff page_mask: 0x1f80010000
[ 4.723066] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2470: nr_pages: 262144 first_page: 0x80000 last_page: 0xfe0fffef
[ 4.723068] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2447: ----CSROW 1 VALID for MC node 1
[ 4.723070] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2410: (csrow=1) DBAM map index= 2
[ 4.723072] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2412: nr_pages= 262144 channel-count = 2
[ 4.723074] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 671: InputAddr 0x10000 translates to DramAddr of same value
[ 4.723077] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 511: DHAR info for node 1 base 0xe0000000 offset 0xa0000000 size 0x20000000
[ 4.723079] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 732: Node 1, DramAddr 0x10000 to SysAddr 0x80010000
[ 4.723081] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 671: InputAddr 0xffffffe07fffffff translates to DramAddr of same value
[ 4.723084] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 511: DHAR info for node 1 base 0xe0000000 offset 0xa0000000 size 0x20000000
[ 4.723086] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 732: Node 1, DramAddr 0xffffffe07fffffff to SysAddr 0xffffffe0ffffffff
[ 4.723089] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 1030: Memory type is: Registered DDR2 RAM
[ 4.723091] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2461: for MC node 1 csrow 1:
[ 4.723093] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2464: input_addr_min: 0x10000 input_addr_max: 0xffffffe07fffffff
[ 4.723095] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2466: sys_addr: 0xffffffe0ffffffff page_mask: 0x1f80010000
[ 4.723097] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2470: nr_pages: 262144 first_page: 0x80010 last_page: 0xfe0fffff
[ 4.723100] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2442: ----CSROW 2 EMPTY for node 1
[ 4.723102] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2442: ----CSROW 3 EMPTY for node 1
[ 4.723104] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2442: ----CSROW 4 EMPTY for node 1
[ 4.723106] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2442: ----CSROW 5 EMPTY for node 1
[ 4.723108] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2442: ----CSROW 6 EMPTY for node 1
[ 4.723109] EDAC DEBUG: in drivers/edac/amd64_edac.c, line at 2442: ----CSROW 7 EMPTY for node 1
[ 4.723112] EDAC DEBUG: in drivers/edac/edac_mc.c, line at 497: edac_mc_add_mc()
[ 4.723113] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 794: edac_create_sysfs_mci_device() idx=1
[ 4.723210] EDAC DEBUG: in drivers/edac/edac_mc.c, line at 320: edac_mc_workq_setup()
[ 4.723212] EDAC MC1: Giving out device to 'amd64_edac' 'RevF': DEV 0000:00:19.2
[ 4.732270] EDAC DEBUG: in drivers/edac/edac_pci.c, line at 49: edac_pci_alloc_ctl_info()
[ 4.732274] EDAC DEBUG: in drivers/edac/edac_pci.c, line at 346: edac_pci_add_device()
[ 4.732276] EDAC DEBUG: in drivers/edac/edac_pci.c, line at 126: add_edac_pci_to_global_list()
[ 4.732278] EDAC DEBUG: in drivers/edac/edac_pci.c, line at 101: find_edac_pci_by_dev()
[ 4.732280] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 444: edac_pci_create_sysfs() idx=0
[ 4.732282] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 347: edac_pci_main_kobj_setup()
[ 4.732333] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 394: Registered '.../edac/pci' kobject
[ 4.732335] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 163: edac_pci_create_instance_kobj()
[ 4.732379] EDAC DEBUG: in drivers/edac/edac_pci_sysfs.c, line at 186: edac_pci_create_instance_kobj() Register instance 'pci0' kobject
[ 4.732382] EDAC DEBUG: in drivers/edac/edac_pci.c, line at 274: edac_pci_workq_setup()
[ 4.732384] EDAC PCI0: Giving out device to module 'amd64_edac' controller 'EDAC PCI controller': DEV '0000:00:18.2' (POLLED)
[ 4.745387] cpuidle: using governor ladder
[ 4.751161] cpuidle: using governor menu
[ 4.758241] usbcore: registered new interface driver hiddev
[ 4.771338] input: HID 062a:0000 as /devices/pci0000:00/0000:00:02.0/usb2/2-9/2-9:1.0/input/input5
[ 4.781296] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 4.787677] ata1.00: ATA-7: SAMSUNG HD642JJ, 1AA01113, max UDMA7
[ 4.787679] ata1.00: 1250263728 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 4.794131] ata1.00: configured for UDMA/100
[ 4.794248] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD642JJ 1AA0 PQ: 0 ANSI: 5
[ 4.794560] sd 0:0:0:0: [sda] 1250263728 512-byte logical blocks: (640 GB/596 GiB)
[ 4.794597] sd 0:0:0:0: [sda] Write Protect is off
[ 4.794599] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.794615] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.848648] sda:
[ 4.850534] generic-usb 0003:062A:0000.0001: input,hidraw0: USB HID v1.10 Mouse [HID 062a:0000] on usb-0000:00:02.0-9/input0
[ 4.865609] usbcore: registered new interface driver usbhid
[ 4.873017] usbhid: USB HID core driver
[ 4.878692] sda1 sda2 sda3
[ 4.883441] Advanced Linux Sound Architecture Driver Version 1.0.21.
[ 4.891796] Bt87x 0000:05:06.1: PCI INT A -> Link[LNKC] -> GSI 19 (level, low) -> IRQ 19
[ 4.901510] sd 0:0:0:0: [sda] Attached SCSI disk
[ 4.908357] bt87x0: Using board 1, analog, digital (rate 32000 Hz)
[ 4.916978] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 22
[ 4.924534] HDA Intel 0000:00:06.1: PCI INT B -> Link[LAZA] -> GSI 22 (level, low) -> IRQ 22
[ 4.934820] alloc irq_desc for 29 on node 0
[ 4.934822] alloc kstat_irqs on node 0
[ 4.934830] HDA Intel 0000:00:06.1: irq 29 for MSI/MSI-X
[ 4.934846] HDA Intel 0000:00:06.1: setting latency timer to 64
[ 6.300449] ALSA device list:
[ 6.305273] #0: HDA NVidia at 0xefafc000 irq 29
[ 6.311794] #1: Brooktree Bt878 at 0xeeffe000, irq 19
[ 6.319124] Initializing XFRM netlink socket
[ 6.325233] NET: Registered protocol family 17
[ 6.331508] NET: Registered protocol family 15
[ 6.337806] powernow-k8: Found 2 Dual-Core AMD Opteron(tm) Processor 2218 processors (4 cpu cores) (version 2.20.00)
[ 6.350242] powernow-k8: 0 : fid 0x12 (2600 MHz), vid 0x8
[ 6.357756] powernow-k8: 1 : fid 0x10 (2400 MHz), vid 0xa
[ 6.365250] powernow-k8: 2 : fid 0xe (2200 MHz), vid 0xc
[ 6.372608] powernow-k8: 3 : fid 0xc (2000 MHz), vid 0xe
[ 6.379987] powernow-k8: 4 : fid 0xa (1800 MHz), vid 0x10
[ 6.387404] powernow-k8: 5 : fid 0x2 (1000 MHz), vid 0x12
[ 6.394928] powernow-k8: 0 : fid 0x12 (2600 MHz), vid 0x8
[ 6.402337] powernow-k8: 1 : fid 0x10 (2400 MHz), vid 0xa
[ 6.409764] powernow-k8: 2 : fid 0xe (2200 MHz), vid 0xc
[ 6.417081] powernow-k8: 3 : fid 0xc (2000 MHz), vid 0xe
[ 6.424358] powernow-k8: 4 : fid 0xa (1800 MHz), vid 0x10
[ 6.431676] powernow-k8: 5 : fid 0x2 (1000 MHz), vid 0x12
[ 7.021264] Clocksource tsc unstable (delta = -302307042 ns)
[ 7.031226] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 7.047876] ata2.00: ATA-7: SAMSUNG HD642JJ, 1AA01113, max UDMA7
[ 7.058145] ata2.00: 1250263728 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.075711] ata2.00: configured for UDMA/100
[ 7.084337] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD642JJ 1AA0 PQ: 0 ANSI: 5
[ 7.097188] sd 1:0:0:0: [sdb] 1250263728 512-byte logical blocks: (640 GB/596 GiB)
[ 7.097392] scsi 2:0:0:0: Direct-Access ATA MAXTOR STM332082 3.AA PQ: 0 ANSI: 5
[ 7.097824] sd 2:0:0:0: [sdc] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 7.097907] sd 2:0:0:0: [sdc] Write Protect is off
[ 7.097911] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 7.098000] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.098277] sdc: sdc1
[ 7.158214] sd 1:0:0:0: [sdb] Write Protect is off
[ 7.158219] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 7.158261] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.185920] sdc2
[ 7.192596] sdb:
[ 7.192981] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 7.225409] sdb1 sdb2 sdb3
[ 7.233411] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 7.490473] ata4: SATA link down (SStatus 0 SControl 300)
[ 7.840470] ata6: SATA link down (SStatus 0 SControl 300)
[ 8.191727] ata8: SATA link down (SStatus 0 SControl 300)
[ 8.201367] ata10: port disabled. ignoring.
[ 8.201430] Freeing unused kernel memory: 1216k freed
[ 8.434513] md: Autodetecting RAID arrays.
[ 8.493534] md: Scanned 4 and added 4 devices.
[ 8.493538] md: autorun ...
[ 8.493542] md: considering sdb3 ...
[ 8.493555] md: adding sdb3 ...
[ 8.493562] md: sdb1 has different UUID to sdb3
[ 8.493570] md: adding sda3 ...
[ 8.493577] md: sda1 has different UUID to sdb3
[ 8.493582] md: created md3
[ 8.493587] md: bind<sda3>
[ 8.493606] md: bind<sdb3>
[ 8.493622] md: running: <sdb3><sda3>
[ 8.506150] raid1: raid set md3 active with 2 out of 2 mirrors
[ 8.514578] md3: bitmap initialized from disk: read 10/10 pages, set 32 bits
[ 8.514582] created bitmap (145 pages) for device md3
[ 8.521942] md3: detected capacity change from 0 to 619651399680
[ 8.522070] md: considering sdb1 ...
[ 8.522084] md: adding sdb1 ...
[ 8.522094] md: adding sda1 ...
[ 8.522408] md: created md2
[ 8.522412] md: bind<sda1>
[ 8.522431] md: bind<sdb1>
[ 8.522448] md: running: <sdb1><sda1>
[ 8.534275] raid1: raid set md2 active with 2 out of 2 mirrors
[ 8.557382] md2: bitmap initialized from disk: read 10/10 pages, set 1 bits
[ 8.557387] created bitmap (153 pages) for device md2
[ 8.578848] md2: detected capacity change from 0 to 10240327680
[ 8.578971] md: ... autorun DONE.
[ 8.583521] md3: unknown partition table
[ 16.599536] XFS mounting filesystem dm-0
[ 17.140006] Ending clean XFS mount for filesystem: dm-0
[ 26.707741] udev: starting version 149
[ 27.076362] md2: unknown partition table
[ 27.145549] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 27.145603] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 27.145655] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 30.192185] XFS mounting filesystem sdc1
[ 30.257648] Ending clean XFS mount for filesystem: sdc1