[PATCH v2 1/6] hid: new driver for PicoLCD device
From: Bruno PrÃmont
Date: Sat Mar 20 2010 - 12:16:28 EST
Add basic driver for PicoLCD graphics device.
Initially support keypad with input device, operation mode switching
and provide support for debugging communication via events file from
debugfs.
Signed-off-by: Bruno PrÃmont <bonbons@xxxxxxxxxxxxxxxxx>
---
Documentation/ABI/testing/sysfs-driver-hid-picolcd | 17 +
drivers/hid/Kconfig | 18 +
drivers/hid/Makefile | 1 +
drivers/hid/hid-core.c | 2 +
drivers/hid/hid-ids.h | 2 +
drivers/hid/hid-picolcd.c | 1244 ++++++++++++++++++++
6 files changed, 1284 insertions(+), 0 deletions(-)
diff --git a/Documentation/ABI/testing/sysfs-driver-hid-picolcd b/Documentation/ABI/testing/sysfs-driver-hid-picolcd
new file mode 100644
index 0000000..1c63a0f
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-driver-hid-picolcd
@@ -0,0 +1,17 @@
+What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/operation_mode
+Date: March 2010
+Contact: Bruno PrÃmont <bonbons@xxxxxxxxxxxxxxxxx>
+Description: Make it possible to switch the PicoLCD device between LCD
+ (firmware) and bootloader (flasher) operation modes.
+
+ Reading: returns list of available modes is show, the active mode
+ being enclosed in brackets ('<' and '>')
+
+ Writing: causes operation mode switch. Permitted values are
+ the non-active mode names listed when read, optionally followed
+ by a delay value expressed in ms.
+
+ Note: when switching mode the current PicoLCD HID device gets
+ disconnected and reconnects after above delay (default value
+ is 5 seconds though this default should not be depended on).
+
diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig
index 24d90ea..7097f0a 100644
--- a/drivers/hid/Kconfig
+++ b/drivers/hid/Kconfig
@@ -227,6 +227,24 @@ config HID_PETALYNX
---help---
Support for Petalynx Maxter remote control.
+config HID_PICOLCD
+ tristate "PicoLCD (graphic version)"
+ depends on USB_HID
+ ---help---
+ This provides support for Minibox PicoLCD devices, currently
+ only the graphical ones are supported.
+
+ This includes support for the following device features:
+ - Keypad
+ - Switching between Firmware and Flash mode
+ Features that are not (yet) supported:
+ - Framebuffer for monochrome 256x64 display
+ - Backlight control
+ - Contrast control
+ - IR
+ - General purpose outputs
+ - EEProm / Flash access
+
config HID_SAMSUNG
tristate "Samsung" if EMBEDDED
depends on USB_HID
diff --git a/drivers/hid/Makefile b/drivers/hid/Makefile
index 0de2dff..f0a4870 100644
--- a/drivers/hid/Makefile
+++ b/drivers/hid/Makefile
@@ -36,6 +36,7 @@ obj-$(CONFIG_HID_MONTEREY) += hid-monterey.o
obj-$(CONFIG_HID_NTRIG) += hid-ntrig.o
obj-$(CONFIG_HID_PANTHERLORD) += hid-pl.o
obj-$(CONFIG_HID_PETALYNX) += hid-petalynx.o
+obj-$(CONFIG_HID_PICOLCD) += hid-picolcd.o
obj-$(CONFIG_HID_SAMSUNG) += hid-samsung.o
obj-$(CONFIG_HID_SMARTJOYPLUS) += hid-sjoy.o
obj-$(CONFIG_HID_SONY) += hid-sony.o
diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c
index a50d850..2bd0671 100644
--- a/drivers/hid/hid-core.c
+++ b/drivers/hid/hid-core.c
@@ -1330,6 +1330,8 @@ static const struct hid_device_id hid_blacklist[] = {
{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_LOGITECH_RUMBLEPAD2) },
{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACETRAVELLER) },
{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACENAVIGATOR) },
+ { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD) },
+ { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD_BOOTLOADER) },
{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_SIDEWINDER_GV) },
{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_NE4K) },
{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_LK6K) },
diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h
index 010368e..6d67582 100644
--- a/drivers/hid/hid-ids.h
+++ b/drivers/hid/hid-ids.h
@@ -330,6 +330,8 @@
#define USB_VENDOR_ID_MICROCHIP 0x04d8
#define USB_DEVICE_ID_PICKIT1 0x0032
#define USB_DEVICE_ID_PICKIT2 0x0033
+#define USB_DEVICE_ID_PICOLCD 0xc002
+#define USB_DEVICE_ID_PICOLCD_BOOTLOADER 0xf002
#define USB_VENDOR_ID_MICROSOFT 0x045e
#define USB_DEVICE_ID_SIDEWINDER_GV 0x003b
diff --git a/drivers/hid/hid-picolcd.c b/drivers/hid/hid-picolcd.c
new file mode 100644
index 0000000..30b8e08
--- /dev/null
+++ b/drivers/hid/hid-picolcd.c
@@ -0,0 +1,1244 @@
+/***************************************************************************
+ * Copyright (C) 2010 by Bruno PrÃmont <bonbons@xxxxxxxxxxxxxxxxx> *
+ * *
+ * Based on Logitech G13 driver (v0.4) *
+ * Copyright (C) 2009 by Rick L. Vinyard, Jr. <rvinyard@xxxxxxxxxxx> *
+ * *
+ * This program is free software: you can redistribute it and/or modify *
+ * it under the terms of the GNU General Public License as published by *
+ * the Free Software Foundation, version 2 of the License. *
+ * *
+ * This driver is distributed in the hope that it will be useful, but *
+ * WITHOUT ANY WARRANTY; without even the implied warranty of *
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU *
+ * General Public License for more details. *
+ * *
+ * You should have received a copy of the GNU General Public License *
+ * along with this software. If not see <http://www.gnu.org/licenses/>. *
+ ***************************************************************************/
+
+#include <linux/hid.h>
+#include <linux/hid-debug.h>
+#include <linux/input.h>
+#include "hid-ids.h"
+#include "usbhid/usbhid.h"
+#include <linux/usb.h>
+
+#include <linux/seq_file.h>
+#include <linux/debugfs.h>
+
+#include <linux/completion.h>
+
+#define PICOLCD_NAME "PicoLCD (graphic)"
+
+/* Report numbers */
+#define REPORT_ERROR_CODE 0x10 /* LCD: IN[16] */
+#define ERR_SUCCESS 0x00
+#define ERR_PARAMETER_MISSING 0x01
+#define ERR_DATA_MISSING 0x02
+#define ERR_BLOCK_READ_ONLY 0x03
+#define ERR_BLOCK_NOT_ERASABLE 0x04
+#define ERR_BLOCK_TOO_BIG 0x05
+#define ERR_SECTION_OVERFLOW 0x06
+#define ERR_INVALID_CMD_LEN 0x07
+#define ERR_INVALID_DATA_LEN 0x08
+#define REPORT_KEY_STATE 0x11 /* LCD: IN[2] */
+#define REPORT_IR_DATA 0x21 /* LCD: IN[63] */
+#define REPORT_EE_DATA 0x32 /* LCD: IN[63] */
+#define REPORT_MEMORY 0x41 /* LCD: IN[63] */
+#define REPORT_LED_STATE 0x81 /* LCD: OUT[1] */
+#define REPORT_BRIGHTNESS 0x91 /* LCD: OUT[1] */
+#define REPORT_CONTRAST 0x92 /* LCD: OUT[1] */
+#define REPORT_RESET 0x93 /* LCD: OUT[2] */
+#define REPORT_LCD_CMD 0x94 /* LCD: OUT[63] */
+#define REPORT_LCD_DATA 0x95 /* LCD: OUT[63] */
+#define REPORT_LCD_CMD_DATA 0x96 /* LCD: OUT[63] */
+#define REPORT_EE_READ 0xa3 /* LCD: OUT[63] */
+#define REPORT_EE_WRITE 0xa4 /* LCD: OUT[63] */
+#define REPORT_ERASE_MEMORY 0xb2 /* LCD: OUT[2] */
+#define REPORT_READ_MEMORY 0xb3 /* LCD: OUT[3] */
+#define REPORT_WRITE_MEMORY 0xb4 /* LCD: OUT[63] */
+#define REPORT_SPLASH_RESTART 0xc1 /* LCD: OUT[1] */
+#define REPORT_EXIT_KEYBOARD 0xef /* LCD: OUT[2] */
+#define REPORT_VERSION 0xf1 /* LCD: IN[2],OUT[1] Bootloader: IN[2],OUT[1] */
+#define REPORT_BL_ERASE_MEMORY 0xf2 /* Bootloader: IN[36],OUT[4] */
+#define REPORT_BL_READ_MEMORY 0xf3 /* Bootloader: IN[36],OUT[4] */
+#define REPORT_BL_WRITE_MEMORY 0xf4 /* Bootloader: IN[36],OUT[36] */
+#define REPORT_DEVID 0xf5 /* LCD: IN[5], OUT[1] Bootloader: IN[5],OUT[1] */
+#define REPORT_SPLASH_SIZE 0xf6 /* LCD: IN[4], OUT[1] */
+#define REPORT_HOOK_VERSION 0xf7 /* LCD: IN[2], OUT[1] */
+#define REPORT_EXIT_FLASHER 0xff /* Bootloader: OUT[2] */
+
+/* Input device
+ *
+ * The PicoLCD has an IR receiver header, a built-in keypad with 5 keys
+ * and header for 4x4 key matrix. The built-in keys are part of the matrix.
+ */
+#define PICOLCD_KEYS 17
+
+static const int def_keymap[PICOLCD_KEYS] = {
+ KEY_RESERVED, /* none */
+ KEY_BACK, /* col 4 + row 1 */
+ KEY_HOMEPAGE, /* col 3 + row 1 */
+ KEY_RESERVED, /* col 2 + row 1 */
+ KEY_RESERVED, /* col 1 + row 1 */
+ KEY_SCROLLUP, /* col 4 + row 2 */
+ KEY_OK, /* col 3 + row 2 */
+ KEY_SCROLLDOWN, /* col 2 + row 2 */
+ KEY_RESERVED, /* col 1 + row 2 */
+ KEY_RESERVED, /* col 4 + row 3 */
+ KEY_RESERVED, /* col 3 + row 3 */
+ KEY_RESERVED, /* col 2 + row 3 */
+ KEY_RESERVED, /* col 1 + row 3 */
+ KEY_RESERVED, /* col 4 + row 4 */
+ KEY_RESERVED, /* col 3 + row 4 */
+ KEY_RESERVED, /* col 2 + row 4 */
+ KEY_RESERVED, /* col 1 + row 4 */
+};
+
+/* Description of in-progress IO operation, used for operations
+ * that trigger response from device */
+struct picolcd_pending {
+ struct hid_report *out_report;
+ struct hid_report *in_report;
+ int raw_size;
+ u8 raw_data[64];
+};
+
+/* Per device data structure */
+struct picolcd_data {
+ struct hid_device *hdev;
+#ifdef CONFIG_DEBUG_FS
+ int addr_sz;
+#endif
+ u8 version[2];
+ /* input stuff */
+ u8 pressed_keys[2];
+ struct input_dev *input_keys;
+ struct input_dev *input_cir;
+ int keycode[PICOLCD_KEYS];
+
+ /* Housekeeping stuff */
+ spinlock_t lock;
+ struct picolcd_pending *pending;
+ struct completion ready;
+ int status;
+#define PICOLCD_BUSY 1
+#define PICOLCD_FAILED 4
+#define PICOLCD_BOOTLOADER 8
+};
+
+
+/* Find a given report */
+#define picolcd_in_report(id, dev) picolcd_report(id, dev, HID_INPUT_REPORT)
+#define picolcd_out_report(id, dev) picolcd_report(id, dev, HID_OUTPUT_REPORT)
+
+static struct hid_report *picolcd_report(int id, struct hid_device *hdev, int dir)
+{
+ struct list_head *feature_report_list = &hdev->report_enum[dir].report_list;
+ struct hid_report *report = NULL;
+
+ list_for_each_entry(report, feature_report_list, list) {
+ if (report->id == id)
+ return report;
+ }
+ dev_warn(&hdev->dev, "No report with id 0x%x found\n", id);
+ return NULL;
+}
+
+#ifdef CONFIG_DEBUG_FS
+static void picolcd_debug_out_report(struct picolcd_data *data,
+ struct hid_device *hdev, struct hid_report *report);
+#define usbhid_submit_report(a, b, c) \
+ picolcd_debug_out_report(hid_get_drvdata(a), a, b); \
+ usbhid_submit_report(a, b, c)
+#endif
+
+/* Submit a report and wait for a reply from device - if device fades away
+ * or does not respond in time, return NULL */
+static struct picolcd_pending* picolcd_send_and_wait(struct hid_device *hdev,
+ int report_id, const u8 *raw_data, int size)
+{
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ struct picolcd_pending *work;
+ struct hid_report *report = picolcd_out_report(report_id, hdev);
+ unsigned long flags;
+ int status, i, j, k;
+
+ if (!report)
+ return NULL;
+ work = kzalloc(sizeof(*work), GFP_KERNEL);
+ if (!work)
+ return NULL;
+
+ work->out_report = report;
+ work->in_report = NULL;
+ work->raw_size = 0;
+
+retry:
+ /* try to get lock and enqueue our job */
+ spin_lock_irqsave(&data->lock, flags);
+ status = data->status;
+ if (data->pending || (status & PICOLCD_FAILED)) {
+ /* some job already pending,
+ * wait for it to complete and try again */
+ spin_unlock_irqrestore(&data->lock, flags);
+ if (status & PICOLCD_FAILED) {
+ kfree(work);
+ return NULL;
+ }
+ wait_for_completion_interruptible_timeout(&data->ready, HZ*2);
+ goto retry;
+ }
+ data->status |= PICOLCD_BUSY;
+ data->pending = work;
+ for (i = k = 0; i < report->maxfield; i++)
+ for (j = 0; j < report->field[i]->report_count; j++) {
+ hid_set_field(report->field[i], j, k < size ? raw_data[k] : 0);
+ k++;
+ }
+ usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+ complete_all(&data->ready);
+ INIT_COMPLETION(data->ready);
+ spin_unlock_irqrestore(&data->lock, flags);
+ /* wait for our job to complete */
+ wait_for_completion_interruptible_timeout(&data->ready, HZ*2);
+
+ spin_lock_irqsave(&data->lock, flags);
+ if (data->pending == work) {
+ data->status &= ~PICOLCD_BUSY;
+ data->pending = NULL;
+ complete_all(&data->ready);
+ spin_unlock_irqrestore(&data->lock, flags);
+ return work;
+ } else {
+ spin_unlock_irqrestore(&data->lock, flags);
+ kfree(work);
+ return NULL;
+ }
+}
+
+/*
+ * input class device
+ */
+static int picolcd_raw_keypad(struct hid_device *hdev,
+ struct hid_report *report, u8 *raw_data, int size)
+{
+ /*
+ * Keypad event
+ * First and second data bytes list currently pressed keys,
+ * 0x00 means no key and at most 2 keys may be pressed at same time
+ */
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ int i, j;
+
+ /* determine newly pressed keys */
+ for (i = 0; i < size; i++) {
+ int key_code;
+ if (raw_data[i] == 0)
+ continue;
+ for (j = 0; j < sizeof(data->pressed_keys); j++)
+ if (data->pressed_keys[j] == raw_data[i])
+ goto key_already_down;
+ for (j = 0; j < sizeof(data->pressed_keys); j++)
+ if (data->pressed_keys[j] == 0) {
+ data->pressed_keys[j] = raw_data[i];
+ break;
+ }
+ input_event(data->input_keys, EV_MSC, MSC_SCAN, raw_data[i]);
+ if (input_get_keycode(data->input_keys, raw_data[i], &key_code))
+ key_code = KEY_UNKNOWN;
+ if (key_code != KEY_UNKNOWN) {
+ dbg_hid(PICOLCD_NAME " got key press for %u:%d", raw_data[i], key_code);
+ input_report_key(data->input_keys, key_code, 1);
+ }
+ input_sync(data->input_keys);
+key_already_down:
+ continue;
+ }
+
+ /* determine newly released keys */
+ for (j = 0; j < sizeof(data->pressed_keys); j++) {
+ int key_code;
+ if (data->pressed_keys[j] == 0)
+ continue;
+ for (i = 0; i < size; i++)
+ if (data->pressed_keys[j] == raw_data[i])
+ goto key_still_down;
+ input_event(data->input_keys, EV_MSC, MSC_SCAN, data->pressed_keys[j]);
+ if (input_get_keycode(data->input_keys, data->pressed_keys[j], &key_code))
+ key_code = KEY_UNKNOWN;
+ if (key_code != KEY_UNKNOWN) {
+ dbg_hid(PICOLCD_NAME " got key release for %u:%d", data->pressed_keys[j], key_code);
+ input_report_key(data->input_keys, key_code, 0);
+ }
+ input_sync(data->input_keys);
+ data->pressed_keys[j] = 0;
+key_still_down:
+ continue;
+ }
+ return 1;
+}
+
+static int picolcd_raw_cir(struct hid_device *hdev,
+ struct hid_report *report, u8 *raw_data, int size)
+{
+ /* Need understanding of CIR data format to implement ... */
+ return 1;
+}
+
+
+
+/*
+ * Reset our device and wait for answer to VERSION request
+ */
+static int picolcd_reset(struct hid_device *hdev)
+{
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ struct hid_report *report = picolcd_out_report(REPORT_RESET, hdev);
+ struct picolcd_pending *verinfo;
+ unsigned long flags;
+
+ if (!data || !report || report->maxfield != 1)
+ return -ENODEV;
+
+ spin_lock_irqsave(&data->lock, flags);
+ complete_all(&data->ready);
+ INIT_COMPLETION(data->ready);
+ if (hdev->product == USB_DEVICE_ID_PICOLCD_BOOTLOADER)
+ data->status |= PICOLCD_BOOTLOADER;
+
+ /* perform the reset */
+ hid_set_field(report->field[0], 0, 1);
+ usbhid_submit_report(hdev, report, USB_DIR_OUT);
+ spin_unlock_irqrestore(&data->lock, flags);
+
+ verinfo = picolcd_send_and_wait(hdev, REPORT_VERSION, NULL, 0);
+ if (verinfo && verinfo->raw_size == 2) {
+ if (data->status & PICOLCD_BOOTLOADER) {
+ dev_info(&hdev->dev, "PicoLCD reset successful, bootloader version %d.%d\n",
+ verinfo->raw_data[0], verinfo->raw_data[1]);
+ data->version[0] = verinfo->raw_data[0];
+ data->version[1] = verinfo->raw_data[1];
+ } else {
+ dev_info(&hdev->dev, "PicoLCD reset successful, firmware version %d.%d\n",
+ verinfo->raw_data[1], verinfo->raw_data[0]);
+ data->version[0] = verinfo->raw_data[1];
+ data->version[1] = verinfo->raw_data[0];
+ }
+ kfree(verinfo);
+ verinfo = NULL;
+ } else if (verinfo) {
+ dev_err(&hdev->dev, "confused, got unexpected version response from PicoLCD after reset\n");
+ kfree(verinfo);
+ verinfo = NULL;
+ } else {
+ dev_err(&hdev->dev, "no version response from PicoLCD after reset");
+ return -EBUSY;
+ }
+
+ return 0;
+}
+
+/*
+ * The "operation_mode" sysfs attribute
+ */
+static ssize_t picolcd_operation_mode_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct picolcd_data *data = dev_get_drvdata(dev);
+
+ if (data->status & PICOLCD_BOOTLOADER)
+ return snprintf(buf, PAGE_SIZE, "<bootloader> lcd\n");
+ else
+ return snprintf(buf, PAGE_SIZE, "bootloader <lcd>\n");
+}
+
+static ssize_t picolcd_operation_mode_store(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ struct picolcd_data *data = dev_get_drvdata(dev);
+ struct hid_report *report = NULL;
+ size_t cnt = count;
+ int timeout = 5000;
+ unsigned u;
+ unsigned long flags;
+
+ if (cnt >= 3 && strncmp("lcd", buf, 3) == 0) {
+ if (data->status & PICOLCD_BOOTLOADER)
+ report = picolcd_out_report(REPORT_EXIT_FLASHER, data->hdev);
+ buf += 3;
+ cnt -= 3;
+ } else if (cnt >= 10 && strncmp("bootloader", buf, 10) == 0) {
+ if (!(data->status & PICOLCD_BOOTLOADER))
+ report = picolcd_out_report(REPORT_EXIT_KEYBOARD, data->hdev);
+ buf += 10;
+ cnt -= 10;
+ }
+ if (!report)
+ return -EINVAL;
+
+ while (cnt > 0 && (*buf == ' ' || *buf == '\t')) {
+ buf++;
+ cnt--;
+ }
+ while (cnt > 0 && (buf[cnt-1] == '\n' || buf[cnt-1] == '\r'))
+ cnt--;
+ if (cnt > 0) {
+ if (sscanf(buf, "%u", &u) != 1)
+ return -EINVAL;
+ if (u > 30000)
+ return -EINVAL;
+ else
+ timeout = u;
+ }
+
+ spin_lock_irqsave(&data->lock, flags);
+ hid_set_field(report->field[0], 0, timeout & 0xff);
+ hid_set_field(report->field[0], 1, (timeout >> 8) & 0xff);
+ usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+ spin_unlock_irqrestore(&data->lock, flags);
+ return count;
+}
+
+static DEVICE_ATTR(operation_mode, 0644, picolcd_operation_mode_show,
+ picolcd_operation_mode_store);
+
+
+#ifdef CONFIG_DEBUG_FS
+/*
+ * Helper code for HID report level dumping/debugging
+ */
+static const char *error_codes[] = {
+ "success", "parameter missing", "data_missing", "block readonly", "block not erasable",
+ "block too big", "section overflow", "invalid command length", "invalid data length",
+};
+
+static void dump_buff_as_hex(char *dst, size_t dst_sz, const u8 *data,
+ const size_t data_len)
+{
+ int i, j;
+ for (i = j = 0; i < data_len && j + 3 < dst_sz; i++) {
+ dst[j++] = hex_asc[(data[i] >> 4) & 0x0f];
+ dst[j++] = hex_asc[data[i] & 0x0f];
+ dst[j++] = ' ';
+ }
+ if (j < dst_sz) {
+ dst[j--] = '\0';
+ dst[j] = '\n';
+ } else
+ dst[j] = '\0';
+}
+
+static void picolcd_debug_out_report(struct picolcd_data *data,
+ struct hid_device *hdev, struct hid_report *report)
+{
+ u8 raw_data[70];
+ int raw_size = (report->size >> 3) + 1;
+ char *buff;
+#define BUFF_SZ 256
+
+ /* Avoid unnecessary overhead if debugfs is disabled */
+ if (!hdev->debug_events)
+ return;
+
+ buff = kmalloc(BUFF_SZ, GFP_ATOMIC);
+ if (!buff)
+ return;
+
+ snprintf(buff, BUFF_SZ, "\nout report %d (size %d) = ",
+ report->id, raw_size);
+ hid_debug_event(hdev, buff);
+ if (raw_size + 5 > sizeof(raw_data)) {
+ hid_debug_event(hdev, " TOO BIG\n");
+ return;
+ } else {
+ raw_data[0] = report->id;
+ hid_output_report(report, raw_data);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data, raw_size);
+ hid_debug_event(hdev, buff);
+ }
+
+ switch (report->id) {
+ case REPORT_LED_STATE:
+ /* 1 data byte with GPO state */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_LED_STATE", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tGPO state: 0x%02x\n", raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_BRIGHTNESS:
+ /* 1 data byte with brightness */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_BRIGHTNESS", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tBrightness: 0x%02x\n", raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_CONTRAST:
+ /* 1 data byte with contrast */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_CONTRAST", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tContrast: 0x%02x\n", raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_RESET:
+ /* 2 data bytes with reset duration in ms */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_RESET", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tDuration: 0x%02x%02x (%dms)\n",
+ raw_data[2], raw_data[1], raw_data[2] << 8 | raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_LCD_CMD:
+ /* 63 data bytes with LCD commands */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_LCD_CMD", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ /* TODO: format decoding */
+ break;
+ case REPORT_LCD_DATA:
+ /* 63 data bytes with LCD data */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_LCD_CMD", report->id, raw_size-1);
+ /* TODO: format decoding */
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_LCD_CMD_DATA:
+ /* 63 data bytes with LCD commands and data */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_LCD_CMD", report->id, raw_size-1);
+ /* TODO: format decoding */
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_EE_READ:
+ /* 3 data bytes with read area description */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_EE_READ", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n", raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_EE_WRITE:
+ /* 3+1..20 data bytes with write area description */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_EE_WRITE", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n", raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[3] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ } else if (raw_data[3] + 4 <= raw_size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ }
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_ERASE_MEMORY:
+ case REPORT_BL_ERASE_MEMORY:
+ /* 3 data bytes with pointer inside erase block */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_ERASE_MEMORY", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ switch (data->addr_sz) {
+ case 2:
+ snprintf(buff, BUFF_SZ, "\tAddress inside 64 byte block: 0x%02x%02x\n",
+ raw_data[2], raw_data[1]);
+ break;
+ case 3:
+ snprintf(buff, BUFF_SZ, "\tAddress inside 64 byte block: 0x%02x%02x%02x\n",
+ raw_data[3], raw_data[2], raw_data[1]);
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "\tNot supported\n");
+ }
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_READ_MEMORY:
+ case REPORT_BL_READ_MEMORY:
+ /* 4 data bytes with read area description */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_READ_MEMORY", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ switch (data->addr_sz) {
+ case 2:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ break;
+ case 3:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n",
+ raw_data[3], raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]);
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "\tNot supported\n");
+ }
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_WRITE_MEMORY:
+ case REPORT_BL_WRITE_MEMORY:
+ /* 4+1..32 data bytes with write adrea description */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_WRITE_MEMORY", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ switch (data->addr_sz) {
+ case 2:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[3] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ } else if (raw_data[3] + 4 <= raw_size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ }
+ break;
+ case 3:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n",
+ raw_data[3], raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[4] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ } else if (raw_data[4] + 5 <= raw_size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+5, raw_data[4]);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ }
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "\tNot supported\n");
+ }
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_SPLASH_RESTART:
+ /* TODO */
+ break;
+ case REPORT_EXIT_KEYBOARD:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_EXIT_KEYBOARD", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tRestart delay: %dms (0x%02x%02x)\n",
+ raw_data[1] | (raw_data[2] << 8),
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_VERSION:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_VERSION", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_DEVID:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_DEVID", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_SPLASH_SIZE:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_SPLASH_SIZE", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_HOOK_VERSION:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_HOOK_VERSION", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_EXIT_FLASHER:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_VERSION", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tRestart delay: %dms (0x%02x%02x)\n",
+ raw_data[1] | (raw_data[2] << 8),
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "<unknown>", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ }
+ wake_up_interruptible(&hdev->debug_wait);
+ kfree(buff);
+}
+
+static inline void picolcd_debug_raw_event(struct picolcd_data *data,
+ struct hid_device *hdev, struct hid_report *report,
+ u8 *raw_data, int size)
+{
+ char *buff;
+
+#define BUFF_SZ 256
+ /* Avoid unnecessary overhead if debugfs is disabled */
+ if (!hdev->debug_events)
+ return;
+
+ buff = kmalloc(BUFF_SZ, GFP_ATOMIC);
+ if (!buff)
+ return;
+
+ switch (report->id) {
+ case REPORT_ERROR_CODE:
+ /* 2 data bytes with affected report and error code */
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_ERROR_CODE", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ if (raw_data[2] < ARRAY_SIZE(error_codes))
+ snprintf(buff, BUFF_SZ, "\tError code 0x%02x (%s) in reply to report 0x%02x\n",
+ raw_data[2], error_codes[raw_data[2]], raw_data[1]);
+ else
+ snprintf(buff, BUFF_SZ, "\tError code 0x%02x in reply to report 0x%02x\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_KEY_STATE:
+ /* 2 data bytes with key state */
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_KEY_STATE", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ if (raw_data[1] == 0)
+ snprintf(buff, BUFF_SZ, "\tNo key pressed\n");
+ else if (raw_data[2] == 0)
+ snprintf(buff, BUFF_SZ, "\tOne key pressed: 0x%02x (%d)\n",
+ raw_data[1], raw_data[1]);
+ else
+ snprintf(buff, BUFF_SZ, "\tTwo keys pressed: 0x%02x (%d), 0x%02x (%d)\n",
+ raw_data[1], raw_data[1], raw_data[2], raw_data[2]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_IR_DATA:
+ /* Up to 20 byes of IR scancode data */
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_IR_DATA", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ if (raw_data[1] == 0) {
+ snprintf(buff, BUFF_SZ, "\tUnexpectedly 0 data length\n");
+ hid_debug_event(hdev, buff);
+ } else if (raw_data[1] + 1 <= size) {
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n\tIR Data: ",
+ raw_data[1]-1);
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+2, raw_data[1]-1);
+ hid_debug_event(hdev, buff);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tOverflowing data length: %d\n",
+ raw_data[1]-1);
+ hid_debug_event(hdev, buff);
+ }
+ break;
+ case REPORT_EE_DATA:
+ /* Data buffer in response to REPORT_EE_READ or REPORT_EE_WRITE */
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_EE_DATA", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n", raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[3] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ hid_debug_event(hdev, buff);
+ } else if (raw_data[3] + 4 <= size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+ hid_debug_event(hdev, buff);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ hid_debug_event(hdev, buff);
+ }
+ break;
+ case REPORT_MEMORY:
+ /* Data buffer in response to REPORT_READ_MEMORY or REPORT_WRTIE_MEMORY */
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_MEMORY", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ switch (data->addr_sz) {
+ case 2:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[3] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ } else if (raw_data[3] + 4 <= size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ }
+ break;
+ case 3:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n",
+ raw_data[3], raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[4] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ } else if (raw_data[4] + 5 <= size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+5, raw_data[4]);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ }
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "\tNot supported\n");
+ }
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_VERSION:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_VERSION", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tFirmware version: %d.%d\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_BL_ERASE_MEMORY:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_BL_ERASE_MEMORY", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ /* TODO */
+ break;
+ case REPORT_BL_READ_MEMORY:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_BL_READ_MEMORY", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ /* TODO */
+ break;
+ case REPORT_BL_WRITE_MEMORY:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_BL_WRITE_MEMORY", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ /* TODO */
+ break;
+ case REPORT_DEVID:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_DEVID", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tSerial: 0x%02x%02x%02x%02x\n",
+ raw_data[1], raw_data[2], raw_data[3], raw_data[4]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tType: 0x%02x\n",
+ raw_data[5]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_SPLASH_SIZE:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_SPLASH_SIZE", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tTotal splash space: %d\n",
+ (raw_data[2] << 8) | raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tUsed splash space: %d\n",
+ (raw_data[4] << 8) | raw_data[3]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_HOOK_VERSION:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_HOOK_VERSION", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tFirmware version: %d.%d\n",
+ raw_data[1], raw_data[2]);
+ hid_debug_event(hdev, buff);
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "<unknown>", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ }
+ wake_up_interruptible(&hdev->debug_wait);
+ kfree(buff);
+}
+#else
+#define picolcd_debug_raw_event(data, hdev, report, raw_data, size)
+#endif
+
+/*
+ * Handle raw report as sent by device
+ */
+static int picolcd_raw_event(struct hid_device *hdev,
+ struct hid_report *report, u8 *raw_data, int size)
+{
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ unsigned long flags;
+ int ret = 0;
+
+ if (data == NULL)
+ return 1;
+
+ if (report->id == REPORT_KEY_STATE) {
+ if (data->input_keys)
+ ret = picolcd_raw_keypad(hdev, report, raw_data+1, size-1);
+ } else if (report->id == REPORT_IR_DATA) {
+ if (data->input_cir)
+ ret = picolcd_raw_cir(hdev, report, raw_data+1, size-1);
+ } else {
+ spin_lock_irqsave(&data->lock, flags);
+ /*
+ * We let the caller of picolcd_send_and_wait() check if the report
+ * we got is one of the expected ones or not.
+ */
+ if (data->pending) {
+ memcpy(data->pending->raw_data, raw_data+1, size-1);
+ data->pending->raw_size = size-1;
+ data->pending->in_report = report;
+ complete_all(&data->ready);
+ }
+ spin_unlock_irqrestore(&data->lock, flags);
+ }
+
+ picolcd_debug_raw_event(data, hdev, report, raw_data, size);
+ return 1;
+}
+
+#ifdef CONFIG_PM
+static int picolcd_suspend(struct hid_device *hdev)
+{
+ dbg_hid(PICOLCD_NAME " device ready for suspend\n");
+ return 0;
+}
+
+static int picolcd_resume(struct hid_device *hdev)
+{
+ return 0;
+}
+
+static int picolcd_reset_resume(struct hid_device *hdev)
+{
+ int ret;
+ ret = picolcd_reset(hdev);
+ if (ret)
+ dbg_hid(PICOLCD_NAME " resetting our device failed: %d\n", ret);
+ return 0;
+}
+#endif
+
+/* initialize keypad input device */
+static inline int picolcd_init_keys(struct picolcd_data *data,
+ struct hid_report *report)
+{
+ struct hid_device *hdev = data->hdev;
+ struct input_dev *idev;
+ int error, i;
+
+ if (!report)
+ return -ENODEV;
+ if (report->maxfield != 1 || report->field[0]->report_count != 2 ||
+ report->field[0]->report_size != 8) {
+ dev_err(&hdev->dev, "unsupported KEY_STATE report");
+ return -EINVAL;
+ }
+
+ idev = input_allocate_device();
+ if (idev == NULL) {
+ dev_err(&hdev->dev, "failed to allocate input device");
+ return -ENOMEM;
+ }
+ input_set_drvdata(idev, hdev);
+ memcpy(data->keycode, def_keymap, sizeof(def_keymap));
+ idev->name = hdev->name;
+ idev->phys = hdev->phys;
+ idev->uniq = hdev->uniq;
+ idev->id.bustype = hdev->bus;
+ idev->id.vendor = hdev->vendor;
+ idev->id.product = hdev->product;
+ idev->id.version = hdev->version;
+ idev->dev.parent = hdev->dev.parent;
+ idev->keycode = &data->keycode;
+ idev->keycodemax = PICOLCD_KEYS;
+ idev->keycodesize = sizeof(int);
+ input_set_capability(idev, EV_MSC, MSC_SCAN);
+ set_bit(EV_REP, idev->evbit);
+ for (i = 0; i < PICOLCD_KEYS; i++) {
+ int key = ((int *)idev->keycode)[i];
+ if (key < KEY_MAX && key >= 0)
+ input_set_capability(idev, EV_KEY, key);
+ }
+ error = input_register_device(idev);
+ if (error) {
+ dev_err(&hdev->dev, "error registering the input device");
+ input_free_device(idev);
+ return error;
+ }
+ data->input_keys = idev;
+ return 0;
+}
+
+static void picolcd_exit_keys(struct picolcd_data *data)
+{
+ struct input_dev *idev = data->input_keys;
+
+ data->input_keys = NULL;
+ if (idev)
+ input_unregister_device(idev);
+}
+
+/* initialize CIR input device */
+static inline int picolcd_init_cir(struct picolcd_data *data, struct hid_report *report)
+{
+ /* support not implemented yet */
+ return 0;
+}
+
+static void picolcd_exit_cir(struct picolcd_data *data)
+{
+}
+
+static inline int picolcd_probe_lcd(struct hid_device *hdev, struct picolcd_data *data)
+{
+ struct picolcd_pending *verinfo;
+ struct hid_report *report;
+ int error;
+
+ verinfo = picolcd_send_and_wait(hdev, REPORT_VERSION, NULL, 0);
+ if (!verinfo || !verinfo->in_report) {
+ kfree(verinfo);
+ dev_err(&hdev->dev, "failed to query FW version of device\n");
+ return -ENODEV;
+ } else if (verinfo->in_report->id == REPORT_VERSION && verinfo->raw_size == 2) {
+ dev_info(&hdev->dev, "detected PicoLCD with firmware version %d.%d\n",
+ verinfo->raw_data[0], verinfo->raw_data[1]);
+ data->version[0] = verinfo->raw_data[1];
+ data->version[1] = verinfo->raw_data[0];
+ if (data->version[0] != 0 && data->version[1] != 3)
+ dev_info(&hdev->dev, "Device with untested firmware revision, "
+ "please submit /sys/kernel/debug/hid/%s/rdesc for this device.\n",
+ dev_name(&hdev->dev));
+ kfree(verinfo);
+ verinfo = NULL;
+ } else {
+ dev_err(&hdev->dev, "unexpected version response from PicoLCD"
+ " (report=0x%02x, size=%d)\n",
+ verinfo->in_report->id, verinfo->raw_size);
+ kfree(verinfo);
+ verinfo = NULL;
+ return -ENODEV;
+ }
+
+ /* Setup keypad input device */
+ error = picolcd_init_keys(data, picolcd_in_report(REPORT_KEY_STATE, hdev));
+ if (error)
+ goto err;
+
+ /* Setup CIR input device */
+ error = picolcd_init_cir(data, picolcd_in_report(REPORT_IR_DATA, hdev));
+ if (error)
+ goto err;
+
+#ifdef CONFIG_DEBUG_FS
+ report = picolcd_out_report(REPORT_READ_MEMORY, hdev);
+ if (report && report->maxfield == 1 && report->field[0]->report_size == 8)
+ data->addr_sz = report->field[0]->report_count - 1;
+ else
+ data->addr_sz = -1;
+#endif
+ return 0;
+err:
+ picolcd_exit_cir(data);
+ picolcd_exit_keys(data);
+ return error;
+}
+
+static inline int picolcd_probe_bootloader(struct hid_device *hdev, struct picolcd_data *data)
+{
+ struct picolcd_pending *verinfo;
+ struct hid_report *report;
+
+ verinfo = picolcd_send_and_wait(hdev, REPORT_VERSION, NULL, 0);
+ if (!verinfo || !verinfo->in_report) {
+ kfree(verinfo);
+ dev_err(&hdev->dev, "failed to query FW version of device\n");
+ return -ENODEV;
+ } else if (verinfo->in_report->id == REPORT_VERSION && verinfo->raw_size == 2) {
+ dev_info(&hdev->dev, "detected PicoLCD with bootloader version %d.%d\n",
+ verinfo->raw_data[1], verinfo->raw_data[0]);
+ data->version[0] = verinfo->raw_data[1];
+ data->version[1] = verinfo->raw_data[0];
+ if (data->version[0] != 1 && data->version[1] != 0)
+ dev_info(&hdev->dev, "Device with untested bootloader revision, "
+ "please submit /sys/kernel/debug/hid/%s/rdesc for this device.\n",
+ dev_name(&hdev->dev));
+ kfree(verinfo);
+ verinfo = NULL;
+ } else {
+ dev_err(&hdev->dev, "unexpected version response from PicoLCD"
+ " (report=0x%02x, size=%d)\n",
+ verinfo->in_report->id, verinfo->raw_size);
+ kfree(verinfo);
+ verinfo = NULL;
+ return -ENODEV;
+ }
+
+#ifdef CONFIG_DEBUG_FS
+ report = picolcd_out_report(REPORT_BL_READ_MEMORY, hdev);
+ if (report && report->maxfield == 1 && report->field[0]->report_size == 8)
+ data->addr_sz = report->field[0]->report_count - 1;
+ else
+ data->addr_sz = -1;
+#endif
+ return 0;
+}
+
+static int picolcd_probe(struct hid_device *hdev,
+ const struct hid_device_id *id)
+{
+ struct picolcd_data *data;
+ int error = -ENOMEM;
+
+ dbg_hid(PICOLCD_NAME " hardware probe...\n");
+
+ /*
+ * Let's allocate the picolcd data structure, set some reasonable
+ * defaults, and associate it with the device
+ */
+ data = kzalloc(sizeof(struct picolcd_data), GFP_KERNEL);
+ if (data == NULL) {
+ dev_err(&hdev->dev, "can't allocate space for Minibox PicoLCD device data\n");
+ error = -ENOMEM;
+ goto err_no_cleanup;
+ }
+
+ spin_lock_init(&data->lock);
+ init_completion(&data->ready);
+ data->hdev = hdev;
+ if (hdev->product == USB_DEVICE_ID_PICOLCD_BOOTLOADER)
+ data->status |= PICOLCD_BOOTLOADER;
+ hid_set_drvdata(hdev, data);
+
+ /* Parse the device reports and start it up */
+ error = hid_parse(hdev);
+ if (error) {
+ dev_err(&hdev->dev, "device report parse failed\n");
+ goto err_cleanup_data;
+ }
+
+ /* We don't use hidinput but hid_hw_start() fails if nothing is
+ * claimed. So spoof claimed input. */
+ hdev->claimed = HID_CLAIMED_INPUT;
+ error = hid_hw_start(hdev, 0);
+ hdev->claimed = 0;
+ if (error) {
+ dev_err(&hdev->dev, "hardware start failed\n");
+ goto err_cleanup_data;
+ }
+
+ error = hdev->ll_driver->open(hdev);
+ if (error) {
+ dev_err(&hdev->dev, "failed to open input interrupt pipe for key and IR events\n");
+ goto err_cleanup_hid_hw;
+ }
+
+ error = sysfs_create_file(&(hdev->dev.kobj), &dev_attr_operation_mode.attr);
+ if (error) {
+ dev_err(&hdev->dev, "failed to create sysfs attributes\n");
+ goto err_cleanup_hid_ll;
+ }
+
+ if (data->status & PICOLCD_BOOTLOADER)
+ error = picolcd_probe_bootloader(hdev, data);
+ else
+ error = picolcd_probe_lcd(hdev, data);
+ if (error)
+ goto err_cleanup_sysfs;
+
+ dbg_hid(PICOLCD_NAME " activated and initialized\n");
+ return 0;
+
+err_cleanup_sysfs:
+ sysfs_remove_file(&(hdev->dev.kobj), &dev_attr_operation_mode.attr);
+err_cleanup_hid_ll:
+ hdev->ll_driver->close(hdev);
+err_cleanup_hid_hw:
+ hid_hw_stop(hdev);
+err_cleanup_data:
+ kfree(data);
+err_no_cleanup:
+ hid_set_drvdata(hdev, NULL);
+
+ return error;
+}
+
+static void picolcd_remove(struct hid_device *hdev)
+{
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ unsigned long flags;
+
+ dbg_hid(PICOLCD_NAME " hardware remove...\n");
+ spin_lock_irqsave(&data->lock, flags);
+ data->status |= PICOLCD_FAILED;
+ spin_unlock_irqrestore(&data->lock, flags);
+
+ sysfs_remove_file(&(hdev->dev.kobj), &dev_attr_operation_mode.attr);
+ hdev->ll_driver->close(hdev);
+ hid_hw_stop(hdev);
+
+ /* Cleanup input */
+ picolcd_exit_cir(data);
+ picolcd_exit_keys(data);
+
+ /* Finally, clean up the picolcd data itself */
+ kfree(data);
+}
+
+static const struct hid_device_id picolcd_devices[] = {
+ { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD) },
+ { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD_BOOTLOADER) },
+ { }
+};
+MODULE_DEVICE_TABLE(hid, picolcd_devices);
+
+static struct hid_driver picolcd_driver = {
+ .name = "hid-picolcd",
+ .id_table = picolcd_devices,
+ .probe = picolcd_probe,
+ .remove = picolcd_remove,
+ .raw_event = picolcd_raw_event,
+#ifdef CONFIG_PM
+ .suspend = picolcd_suspend,
+ .resume = picolcd_resume,
+ .reset_resume = picolcd_reset_resume,
+#endif
+};
+
+static int __init picolcd_init(void)
+{
+ return hid_register_driver(&picolcd_driver);
+}
+
+static void __exit picolcd_exit(void)
+{
+ hid_unregister_driver(&picolcd_driver);
+}
+
+module_init(picolcd_init);
+module_exit(picolcd_exit);
+MODULE_DESCRIPTION("Minibox graphics PicoLCD Driver");
+MODULE_LICENSE("GPL v2");
--
1.6.4.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/