Re: [PATCH] Quirk to fix suspend/resume on Lenovo Edge 11,13,14,15

[Manoj Iyer]

Borislav,

Please see attached lspci output.

Thanks
Manoj

On Thu, Jan 13, 2011 at 11:55 AM, Borislav Petkov <bp@xxxxxxxxx> wrote:
> On Thu, Jan 13, 2011 at 12:33:27PM -0500, Manoj Iyer wrote:
>> Borislav,
>>
>> Please see below lspci and dmesg output from AMD based ThinkPad Edge 11.
>>
>> lspci
>> =====
>> 00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS780 Host
>> Bridge Alternate [1022:9601]
>>         Subsystem: Lenovo Device [17aa:21ca]
>>         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>> Stepping- SERR- FastB2B- DisINTx-
>>         Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort+ >SERR- <PERR- INTx-
>>         Latency: 0
>>         Capabilities: [c4] HyperTransport: Slave or Primary Interface
>>                 Command: BaseUnitID=0 UnitCnt=12 MastHost- DefDir- DUL-
>>                 Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
>> IsocEn- LSEn+ ExtCTL- 64b-
>>                 Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit
>> DwFcInEn- LWO=16bit DwFcOutEn-
>>                 Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
>> IsocEn- LSEn- ExtCTL- 64b-
>>                 Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit
>> DwFcInEn- LWO=8bit DwFcOutEn-
>>                 Revision ID: 3.00
>>                 Link Frequency 0: 1.0GHz
>>                 Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
>>                 Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+
>> 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
>>                 Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
>>                 Link Frequency 1: 200MHz
>>                 Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
>>                 Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz-
>> 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
>>                 Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF-
>> RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
>>                 Prefetchable memory behind bridge Upper: 00-00
>>                 Bus Number: 00
>>         Capabilities: [54] HyperTransport: UnitID Clumping
>>         Capabilities: [40] HyperTransport: Retry Mode
>>         Capabilities: [9c] HyperTransport: #1a
>>         Capabilities: [f8] HyperTransport: #1c
>>
>> 00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to
>> PCI bridge (int gfx) [1022:9602] (prog-if 00 [Normal decode])
>>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>> Stepping- SERR- FastB2B- DisINTx-
>>         Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>         Latency: 64
>>         Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
>>         I/O behind bridge: 00009000-00009fff
>>         Memory behind bridge: d0400000-d05fffff
>>         Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
>>         Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort+ <SERR- <PERR-
>>         BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
>>                 PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>>         Capabilities: [44] HyperTransport: MSI Mapping Enable+ Fixed+
>>         Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] RS780 PCI
>> to PCI bridge (int gfx) [1022:9602]
>>         Kernel modules: shpchp
>>
>> 00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to
>> PCI bridge (PCIE port 0) [1022:9604] (prog-if 00 [Normal decode])
>>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>> Stepping- SERR- FastB2B- DisINTx+
>>         Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>         Latency: 0, Cache Line Size: 32 bytes
>>         Bus: primary=00, secondary=02, subordinate=07, sec-latency=0
>>         I/O behind bridge: 0000a000-0000bfff
>>         Memory behind bridge: 80000000-800fffff
>>         Prefetchable memory behind bridge: 00000000d0000000-00000000d03fffff
>>         Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
>> <TAbort- <MAbort- <SERR- <PERR-
>>         BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
>>                 PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>>         Capabilities: [50] Power Management version 3
>>                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
>>                 Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>>         Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
>>                 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
>>                         ExtTag+ RBE+ FLReset-
>>                 DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
>>                         RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
>>
>
> This doesn't look complete since it shows only 3 PCI devices. Can you do
>
> lspci -vv >> lspci.out
>
> and attach the file instead since the mail client wraps the lines anyway.
>
> Thanks.
>
> --
> Regards/Gruss,
> Boris.
>
> Advanced Micro Devices GmbH
> Einsteinring 24, 85609 Dornach
> General Managers: Alberto Bozzo, Andrew Bowd
> Registration: Dornach, Gemeinde Aschheim, Landkreis Muenchen
> Registergericht Muenchen, HRB Nr. 43632
>



-- 
--manjo

Attachment: lspci.out
Description: Binary data