Re: [PATCH] tty/serial: change of_serial to use new of_property_read_u32()api

From: Rob Herring
Date: Thu Jun 30 2011 - 16:57:32 EST


Grant,

On 06/30/2011 02:00 PM, Grant Likely wrote:
> Simplifies the code a bit and drops a few lines.
>
> Signed-off-by: Grant Likely <grant.likely@xxxxxxxxxxxx>
> ---
>
> I've only actually build tested this, but this shows some of the cleanup
> achieved using the of_property_read_u32() API. If this gets merged in the
> v3.1 merge window then it will need to go via the devicetree/next branch.
>
> g.

You can't give yourself bonus points. ;)

>
> drivers/tty/serial/of_serial.c | 37 +++++++++++++++----------------------
> 1 files changed, 15 insertions(+), 22 deletions(-)
>
> diff --git a/drivers/tty/serial/of_serial.c b/drivers/tty/serial/of_serial.c
> index 36038ed..dbfbfda 100644
> --- a/drivers/tty/serial/of_serial.c
> +++ b/drivers/tty/serial/of_serial.c
> @@ -32,17 +32,17 @@ static int __devinit of_platform_serial_setup(struct platform_device *ofdev,
> {
> struct resource resource;
> struct device_node *np = ofdev->dev.of_node;
> - const __be32 *clk, *spd;
> - const __be32 *prop;
> - int ret, prop_size;
> + u32 clk, spd, prop;
> + int ret;
>
> memset(port, 0, sizeof *port);
> - spd = of_get_property(np, "current-speed", NULL);
> - clk = of_get_property(np, "clock-frequency", NULL);
> - if (!clk) {
> + if (of_property_read_u32(np, "clock-frequency", &clk)) {

s/clk/port->uartclk/

And below, then remove clk.

> dev_warn(&ofdev->dev, "no clock-frequency property set\n");
> return -ENODEV;
> }
> + /* If current-speed was set, then try not to change it. */
> + if (of_property_read_u32(np, "current-speed", &spd) == 0)
> + port->custom_divisor = clk / (16 * spd);
>
> ret = of_address_to_resource(np, 0, &resource);
> if (ret) {
> @@ -54,20 +54,17 @@ static int __devinit of_platform_serial_setup(struct platform_device *ofdev,
> port->mapbase = resource.start;
>
> /* Check for shifted address mapping */
> - prop = of_get_property(np, "reg-offset", &prop_size);
> - if (prop && (prop_size == sizeof(u32)))
> - port->mapbase += be32_to_cpup(prop);
> + if (of_property_read_u32(np, "reg-offset", &prop) == 0)
> + port->mapbase += prop;
>
> /* Check for registers offset within the devices address range */
> - prop = of_get_property(np, "reg-shift", &prop_size);
> - if (prop && (prop_size == sizeof(u32)))
> - port->regshift = be32_to_cpup(prop);
> + if (of_property_read_u32(np, "reg-shift", &prop) == 0)
> + port->regshift = prop;

Can be further simplified:

of_property_read_u32(np, "reg-shift", &port->regshift);

Rob

>
> port->irq = irq_of_parse_and_map(np, 0);
> port->iotype = UPIO_MEM;
> - prop = of_get_property(np, "reg-io-width", &prop_size);
> - if (prop && (prop_size == sizeof(u32))) {
> - switch (be32_to_cpup(prop)) {
> + if (of_property_read_u32(np, "reg-io-width", &prop) == 0) {
> + switch (prop) {
> case 1:
> port->iotype = UPIO_MEM;
> break;
> @@ -75,21 +72,17 @@ static int __devinit of_platform_serial_setup(struct platform_device *ofdev,
> port->iotype = UPIO_MEM32;
> break;
> default:
> - dev_warn(&ofdev->dev,
> - "unsupported io width (%d bytes)\n",
> - be32_to_cpup(prop));
> + dev_warn(&ofdev->dev, "unsupported reg-io-width (%d)\n",
> + prop);
> return -EINVAL;
> }
> }
>
> port->type = type;
> - port->uartclk = be32_to_cpup(clk);
> + port->uartclk = clk;
> port->flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP
> | UPF_FIXED_PORT | UPF_FIXED_TYPE;
> port->dev = &ofdev->dev;
> - /* If current-speed was set, then try not to change it. */
> - if (spd)
> - port->custom_divisor = be32_to_cpup(clk) / (16 * (be32_to_cpup(spd)));
>
> return 0;
> }
>
> _______________________________________________
> devicetree-discuss mailing list
> devicetree-discuss@xxxxxxxxxxxxxxxx
> https://lists.ozlabs.org/listinfo/devicetree-discuss

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/