[PATCH 1/2] Staging: comedi: fix line over 80 character issue in s626.c
From: Ravishankar K Mallikarjunayya
Date: Thu Sep 08 2011 - 19:53:40 EST
This is a patch to the s626.c file that fixes up a line over 80 character warning found by the checkpatch.pl tool
Signed-off-by: Ravishankar K Mallikarjunayya <ravishankar.km@xxxxxxxxxxxxxxx>
---
drivers/staging/comedi/drivers/s626.c | 77 +++++++++++++++++++-------------
1 files changed, 46 insertions(+), 31 deletions(-)
diff --git a/drivers/staging/comedi/drivers/s626.c b/drivers/staging/comedi/drivers/s626.c
index 23fc64b..de07552 100644
--- a/drivers/staging/comedi/drivers/s626.c
+++ b/drivers/staging/comedi/drivers/s626.c
@@ -149,7 +149,8 @@ struct s626_private {
uint16_t CounterIntEnabs;
/* Counter interrupt enable mask for MISC2 register. */
uint8_t AdcItems; /* Number of items in ADC poll list. */
- struct bufferDMA RPSBuf; /* DMA buffer used to hold ADC (RPS1) program. */
+ /* DMA buffer used to hold ADC (RPS1) program. */
+ struct bufferDMA RPSBuf;
struct bufferDMA ANABuf;
/* DMA buffer used to receive ADC data and hold DAC data. */
uint32_t *pDacWBuf;
@@ -785,24 +786,29 @@ static int s626_attach(struct comedi_device *dev, struct comedi_devconfig *it)
/* Init GPIO so that ADC Start* is negated. */
WR7146(P_GPIO, GPIO_BASE | GPIO1_HI);
- /* IsBoardRevA is a boolean that indicates whether the board is RevA.
+ /*
+ * IsBoardRevA is a boolean that indicates whether the board is
+ * RevA.
*
- * VERSION 2.01 CHANGE: REV A & B BOARDS NOW SUPPORTED BY DYNAMIC
- * EEPROM ADDRESS SELECTION. Initialize the I2C interface, which
- * is used to access the onboard serial EEPROM. The EEPROM's I2C
- * DeviceAddress is hardwired to a value that is dependent on the
- * 626 board revision. On all board revisions, the EEPROM stores
- * TrimDAC calibration constants for analog I/O. On RevB and
- * higher boards, the DeviceAddress is hardwired to 0 to enable
- * the EEPROM to also store the PCI SubVendorID and SubDeviceID;
- * this is the address at which the SAA7146 expects a
- * configuration EEPROM to reside. On RevA boards, the EEPROM
- * device address, which is hardwired to 4, prevents the SAA7146
- * from retrieving PCI sub-IDs, so the SAA7146 uses its built-in
- * default values, instead.
+ * VERSION 2.01 CHANGE: REV A & B BOARDS NOW SUPPORTED BY
+ * DYNAMIC EEPROM ADDRESS SELECTION. Initialize the I2C
+ * interface, which is used to access the onboard serial EEPROM.
+ * The EEPROM's I2C DeviceAddress is hardwired to a value that
+ * is dependent on the 626 board revision. On all board
+ * revisions, the EEPROM stores TrimDAC calibration constants
+ * for analog I/O. On RevB and higher boards, the DeviceAddress
+ * is hardwired to 0 to enable the EEPROM to also store the PCI
+ * SubVendorID and SubDeviceID; this is the address at which
+ * the SAA7146 expects a configuration EEPROM to reside.
+ * On RevA boards, the EEPROM device address, which is hardwired
+ * to 4, prevents the SAA7146 from retrieving PCI sub-IDs,
+ * so the SAA7146 uses its built-in default values, instead.
*/
- /* devpriv->I2Cards= IsBoardRevA ? 0xA8 : 0xA0; // Set I2C EEPROM */
+ /*
+ * devpriv->I2Cards= IsBoardRevA ? 0xA8 : 0xA0;
+ * // Set I2C EEPROM
+ */
/* DeviceType (0xA0) */
/* and DeviceAddress<<1. */
@@ -910,8 +916,10 @@ static int s626_attach(struct comedi_device *dev, struct comedi_devconfig *it)
devpriv->ANABuf.PhysicalBase +
(DAC_WDMABUF_OS * sizeof(uint32_t));
- WR7146(P_BASEA2_OUT, (uint32_t) pPhysBuf); /* Buffer base adrs. */
- WR7146(P_PROTA2_OUT, (uint32_t) (pPhysBuf + sizeof(uint32_t))); /* Protection address. */
+ /* Buffer base adrs. */
+ WR7146(P_BASEA2_OUT, (uint32_t) pPhysBuf);
+ /* Protection address. */
+ WR7146(P_PROTA2_OUT, (uint32_t) (pPhysBuf + sizeof(uint32_t)));
/* Cache Audio2's output DMA buffer logical address. This is
* where DAC data is buffered for A2 output DMA transfers. */
@@ -930,8 +938,8 @@ static int s626_attach(struct comedi_device *dev, struct comedi_devconfig *it)
* to the DAC devices. Slot 0 is a NOP that is used to trap TSL
* execution; this permits other slots to be safely modified
* without first turning off the TSL sequencer (which is
- * apparently impossible to do). Also, SD3 (which is driven by a
- * pull-up resistor) is shifted in and stored to the MSB of
+ * apparently impossible to do). Also, SD3 (which is driven
+ * by a pull-up resistor) is shifted in and stored to the MSB of
* FB_BUFFER2 to be used as evidence that the slot sequence has
* not yet finished executing.
*/
@@ -962,11 +970,13 @@ static int s626_attach(struct comedi_device *dev, struct comedi_devconfig *it)
LoadTrimDACs(dev);
LoadTrimDACs(dev); /* Insurance. */
- /* Manually init all gate array hardware in case this is a soft
+ /*
+ * Manually init all gate array hardware in case this is a soft
* reset (we have no way of determining whether this is a warm
- * or cold start). This is necessary because the gate array will
- * reset only in response to a PCI hard reset; there is no soft
- * reset function. */
+ * or cold start). This is necessary because the gate array
+ * will reset only in response to a PCI hard reset; there is no
+ * soft reset function.
+ */
/* Init all DAC outputs to 0V and init all DAC setpoint and
* polarity images.
@@ -980,9 +990,11 @@ static int s626_attach(struct comedi_device *dev, struct comedi_devconfig *it)
*/
devpriv->ChargeEnabled = 0;
- /* Init image of watchdog timer interval in WRMISC2. This image
+ /*
+ * Init image of watchdog timer interval in WRMISC2. This image
* maintains the value of the control bits of MISC2 are
- * continuously reset to zero as long as the WD timer is disabled.
+ * continuously reset to zero as long as the WD timer is
+ * disabled.
*/
devpriv->WDInterval = 0;
@@ -1079,16 +1091,19 @@ static irqreturn_t s626_irq_handler(int irq, void *d)
s = dev->subdevices;
cmd = &(s->async->cmd);
- /* Init ptr to DMA buffer that holds new ADC data. We skip the
- * first uint16_t in the buffer because it contains junk data from
- * the final ADC of the previous poll list scan.
+ /*
+ * Init ptr to DMA buffer that holds new ADC data. We skip the
+ * first uint16_t in the buffer because it contains junk data
+ * from the final ADC of the previous poll list scan.
*/
readaddr = (int32_t *) devpriv->ANABuf.LogicalBase + 1;
/* get the data and hand it over to comedi */
for (i = 0; i < (s->async->cmd.chanlist_len); i++) {
- /* Convert ADC data to 16-bit integer values and copy to application */
- /* buffer. */
+ /*
+ * Convert ADC data to 16-bit integer values and copy to
+ * application buffer.
+ */
tempdata = s626_ai_reg_to_uint((int)*readaddr);
readaddr++;
--
1.6.5.2
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/