RE: [RFC v2 4/9] of: add clock providers

[Stephen Warren]

Turquette, Mike wrote at Tuesday, January 17, 2012 4:37 PM:
> On Tue, Jan 17, 2012 at 2:47 PM, Grant Likely <grant.likely@xxxxxxxxxxxx> wrote:
> > On Tue, Jan 17, 2012 at 1:44 PM, Stephen Warren <swarren@xxxxxxxxxx> wrote:
> >> In other words, does the UART driver need to do something like:
> >>
> >> clk_reg = clk_get(dev, "register");
> >> clk_parent = of_clk_get_by_name(np, "register);
> >> clk_set_parent(clk_reg, clk_parent);
> >>
> >> Or will that all happen transparently within just the of_clk_get_by_name
> >> call?
> >>
> >> (I suppose this question makes slightly more sense for the PLL itself,
> >> since both the upstream and downstream clocks are represented in the PLL
> >> node, whereas the UART's node only represents the clock consumer side,
> >> so the above code isn't really possible automatically).
> >
> > The intent is that device only interacts with the leaf device.  If the
> > clocks are arranged into a hierarchy, then the clock driver is
> > responsible for any interactions with the parent clock.  Requiring the
> > driver to manipulate parent clocks directly defeats the purpose of
> > having a clock abstraction.

Ah OK, so the clock bindings are purely a way of naming the clocks that
devices use; nothing beyond that.

> I don't think that we can get rid of all instances of drivers knowing
> a bit about hierarchy.  I think we can get rid of most, but there are
> cases where it is valid for a driver to know some of the details.
> More on that below.
> 
> >> Somewhat related to this: How does dynamic reparenting interact with
> >> the DT clock binding; is the DT just the default/initial clock setup,
> >> and anything beyond that needs a custom binding and code in the consumer?
> >
> > As far as the clock binding goes, it only describes provider/consumer
> > relationships.  The fact that such relationships may resolve to a
> > hierarchy is beyond what the binding describes.  If a clock has
> > multiple possible parents, then that specific clock binding should
> > document how the multiple parent clocks are described and the clock
> > driver is responsible for implementing the correct behaviour.
> 
> It also deserves to be said that the DT data says nothing about which
> of the possible parents _should_ be the input to a mux clock.  It's
> pretty common to want to make changes to hierarchy after taking a
> device out of reset, since the reset values for a clock management IP
> might be pretty conservative.  So someone, somewhere must know some
> details about hierarchy and set things up correctly.  Maybe a "clock
> driver" can do this, but for specific IPs such as the audio example
> below it makes sense for that driver to have the knowledge.
> 
> > Similarly, the DT clock binding provides no generic mechanism for
> > walking up the clock tree.  That behaviour must also be implemented by
> > each specific clock driver.
> >
> >> I'm thinking of say a system with 1 I2S controller, and both an internal
> >> and external I2S clock source, where perhaps the internal source needs
> >> to be used to capture from an I2S interface on one set of pins (e.g.
> >> analog mic) but the other clock source needs to be used to capture from
> >> I2S on another set of pins (e.g. digital baseband unit connection).
> >> (This example is theoretical, but I'm sure there are other dynamic clock
> >> cases in practice).
> >
> > That is a reasonable example.  In this case, the i2c controller would
> > include both in its clocks property, and the binding would document
> > when and why each clock source is used.
> 
> I'm confused on this point.  How does the binding "document when and
> why each clock is used"?  In the case where this I2S controller
> expects to dynamically switch roles at run-time (analog mic versus
> baseband) then clk_set_parent must still be invoked by the driver.  To
> be clear I'm imagining the above example like:
> 
> i_I2S   e_I2S
>    \       /
>     I2S_mux
>         |
> I2S controller IP

Here's how I envisage this working specifically for the case of some
of Tegra's audio clocking:

There's an oscillator on the board:

osc: pclk {
    compatible = "fixed-clock";
    #clock-cells = <0>;
    clock-frequency = <32768>;
};

(that part might not be quite right, but it's not too important)

The Tegra CAR (Clock And Reset) controller is pretty bare; we rely on
the driver internally defining what all the clocks are, and at most
listing all the clocks that this block imports/exports:

    tegra_car: car@60006000 {
        compatible = "nvidia,tegra20-car";
        reg = < 0x60006000 0x1000 >;
        #clock-cells = <1>;
        clocks = <&osc 0>;
        clock-names = "osc";
        clock-output-names = "pll_a", "audio_2x", "audio", "i2s1", ...;
    };

The I2S controller is pretty dumb, and just receives a single clock that
it enables/disables based on when registers are being touched or audio
is streaming:

tegra_i2s1: i2s@70002800 {
    compatible = "nvidia,tegra20-i2s";
    reg = <0x70002800 0x200>;
    clocks = <&tegra_car 3>;
    clock-names = "clk";
};

So in fact, zero clock /tree/ knowledge there really.

All the clock tree setup is already handled by the ASoC machine driver.
I've already posted a binding for this for the Tegra-with-WM8903-codec
case. Right now, that driver hard-codes the clock names (it's the same
driver from before the days of device tree), but I'll update it to
extract them from device tree using this new binding. Since it touches
the audio PLL, an audio-specific mux, and the I2S clocks, that module
needs references to all of those:

sound {
    compatible = "nvidia,tegra-audio-wm8903-harmony",
                 "nvidia,tegra-audio-wm8903";
    clocks = <&tegra_car 0 &tegra_car 1 &tegra_car 2 &tegra_car 3>;
    clock-names = "pll_a", "audio_2x", "audio", "i2s1";
};

When this top-level sound driver probes, it'll call of_clk_get_by_name()
on each of those, and call clk_set_parent() on the appropriate pairs.
The binding for nvidia,tegra-audio-wm8903 will define the list of
clocks/clock-names that it requires to make this work. Later on, this
top-level driver also calls clk_set_rate() on pll_a to switch between
44.1KHz/48KHz-based audio, etc.


If the clock mux were inside the I2C controller for some other HW, the
I2C node would contain both those clocks and operate on them in a similar
fashion, and the binding would need to say what it expected those two
clocks to represent.

-- 
nvpublic

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/