Re: PROBLEM: Data corruption when pasting large data to terminal

[Bruno PrÃmont]

Hi Egmont,

On Sun, 19 February 2012 Egmont Koblinger <egmont@xxxxxxxxx> wrote:
> Unfortunately the lost tail is a different thing: the terminal is in
> cooked mode by default, so the kernel intentionally keeps the data in
> its buffer until it sees a complete line.  A quick-and-dirty way of
> changing to byte-based transmission (I'm lazy to look up the actual
> system calls, apologies for the terribly ugly way of doing this) is:
>                  pty = open(ptsdname, O_RDWR):
>                  if (pty == -1) { ... }
> +                char cmd[100];
> +                sprintf(cmd, "stty raw <>%s", ptsdname);
> +                system(cmd);
>                  ptmx_slave_test(pty, line, rsz);
> 
> Anyway, thanks very much for your test program, I'll try to modify it
> to trigger the data corruption bug.

Well, not sure but the closing of ptmx on sender side should force kernel
to flush whatever is remaining independently on end-of-line (I was
thinking I should push an EOF over the ptmx instead of closing it before
waiting for child process though I have not yet looked-up how to do so!).

The amount of missing tail for my few runs of the test program were of
varying length, but in all cases way more than a single line, thus I would
hope it's not line-buffering by the kernel which causes the missing data!

Bruno


> egmont
> 
> On Fri, Feb 17, 2012 at 22:57, Bruno PrÃmont <bonbons@xxxxxxxxxxxxxxxxx> wrote:
> > Hi,
> >
> > On Fri, 17 February 2012 Pavel Machek <pavel@xxxxxx> wrote:
> >> > > Sorry, I didn't emphasize the point that makes me suspect it's a kernel issue:
> >> > >
> >> > > - strace reveals that the terminal emulator writes the correct data
> >> > > into /dev/ptmx, and the kernel reports no short writes(!), all the
> >> > > write(..., ..., 68) calls actually return 68 (the length of the
> >> > > example file's lines incl. newline; I'm naively assuming I can trust
> >> > > strace here.)
> >> > > - strace reveals that the receiving application (bash) doesn't receive
> >> > > all the data from /dev/pts/N.
> >> > > - so: the data gets lost after writing to /dev/ptmx, but before
> >> > > reading it out from /dev/pts/N.
> >> >
> >> > Which it will, if the reader doesn't read fast enough, right? ÂIs the
> >> > data somewhere guaranteed to never "overrun" the buffer? ÂIf so, how do
> >> > we handle not just running out of memory?
> >>
> >> Start blocking the writer?
> >
> > I did quickly write a small test program (attached). It forks a reader child
> > and sends data over to it, at the end both write down their copy of the buffer
> > to a /tmp/ptmx_{in,out}.txt file for manual comparing results (in addition
> > to basic output of mismatch start line)
> >
> > From the time it took the writer to write larger buffers (as seen using strace)
> > it seems there *is* some kind of blocking, but it's not blocking long enough
> > or unblocking too early if the reader does not keep up.
> >
> >
> > For quick and dirty testing of effects of buffer sizes, tune "rsz", "wsz"
> > and "line" in main() as well as total size with BUFF_SZ define.
> >
> >
> > The effects for me are that writer writes all data but reader never sees tail
> > of written data (how much is being seen seems variable, probably matter of
> > scheduling, frequency scaling and similar racing factors).
> >
> > My test system is single-core uniprocessor centrino laptop (32bit x86) with
> > 3.2.5 kernel.
> >
> > Bruno
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/