[PATCH v2 1/2] ARM: DTS: tegra: Add USB entries for Tegra30
From: Tuomas Tynkkynen
Date: Thu Aug 01 2013 - 11:01:04 EST
Add device tree entries for the 3 USB controllers and PHYs and
enable the third controller on Cardhu and Beaver boards.
Fix VBUS regulator entries on Beaver. The GPIO pins were wrong.
Also, internal pullups need to be enabled on those pins.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@xxxxxxxxxx>
---
v2: Use internal pullups on the VBUS regulator GPIOs.
arch/arm/boot/dts/tegra30-beaver.dts | 22 ++++++++-
arch/arm/boot/dts/tegra30-cardhu.dtsi | 9 ++++
arch/arm/boot/dts/tegra30.dtsi | 86 +++++++++++++++++++++++++++++++++++
3 files changed, 115 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-beaver.dts b/arch/arm/boot/dts/tegra30-beaver.dts
index 87c5f7b..fa6f6a6 100644
--- a/arch/arm/boot/dts/tegra30-beaver.dts
+++ b/arch/arm/boot/dts/tegra30-beaver.dts
@@ -76,6 +76,11 @@
nvidia,pull = <0>;
nvidia,tristate = <0>;
};
+ pex_l1_prsnt_n_pdd4 {
+ nvidia,pins = "pex_l1_prsnt_n_pdd4",
+ "pex_l1_clkreq_n_pdd6";
+ nvidia,pull = <2>;
+ };
sdio3 {
nvidia,pins = "drive_sdio3";
nvidia,high-speed-mode = <0>;
@@ -85,6 +90,10 @@
nvidia,slew-rate-rising = <1>;
nvidia,slew-rate-falling = <1>;
};
+ gpv {
+ nvidia,pins = "drive_gpv";
+ nvidia,pull-up-strength = <16>;
+ };
};
};
@@ -285,6 +294,15 @@
non-removable;
};
+ usb@7d008000 {
+ status = "okay";
+ };
+
+ usb-phy@7d008000 {
+ vbus-supply = <&usb3_vbus_reg>;
+ status = "okay";
+ };
+
clocks {
compatible = "simple-bus";
#address-cells = <1>;
@@ -357,7 +375,7 @@
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
- gpio = <&gpio TEGRA_GPIO(I, 4) GPIO_ACTIVE_HIGH>;
+ gpio = <&gpio TEGRA_GPIO(DD, 6) GPIO_ACTIVE_HIGH>;
gpio-open-drain;
vin-supply = <&vdd_5v_in_reg>;
};
@@ -369,7 +387,7 @@
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
- gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
+ gpio = <&gpio TEGRA_GPIO(DD, 4) GPIO_ACTIVE_HIGH>;
gpio-open-drain;
vin-supply = <&vdd_5v_in_reg>;
};
diff --git a/arch/arm/boot/dts/tegra30-cardhu.dtsi b/arch/arm/boot/dts/tegra30-cardhu.dtsi
index f65b53d..7af52e4 100644
--- a/arch/arm/boot/dts/tegra30-cardhu.dtsi
+++ b/arch/arm/boot/dts/tegra30-cardhu.dtsi
@@ -330,6 +330,15 @@
non-removable;
};
+ usb@7d008000 {
+ status = "okay";
+ };
+
+ usb-phy@7d008000 {
+ vbus-supply = <&usb3_vbus_reg>;
+ status = "okay";
+ };
+
clocks {
compatible = "simple-bus";
#address-cells = <1>;
diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi
index d8783f0..9920797 100644
--- a/arch/arm/boot/dts/tegra30.dtsi
+++ b/arch/arm/boot/dts/tegra30.dtsi
@@ -561,6 +561,92 @@
status = "disabled";
};
+ usb@7d000000 {
+ compatible = "nvidia,tegra30-ehci", "usb-ehci";
+ reg = <0x7d000000 0x4000>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ phy_type = "utmi";
+ clocks = <&tegra_car TEGRA30_CLK_USBD>;
+ nvidia,needs-double-reset;
+ nvidia,phy = <&phy1>;
+ status = "disabled";
+ };
+
+ phy1: usb-phy@7d000000 {
+ compatible = "nvidia,tegra30-usb-phy";
+ reg = <0x7d000000 0x4000 0x7d000000 0x4000>;
+ phy_type = "utmi";
+ clocks = <&tegra_car TEGRA30_CLK_USBD>,
+ <&tegra_car TEGRA30_CLK_PLL_U>,
+ <&tegra_car TEGRA30_CLK_USBD>;
+ clock-names = "reg", "pll_u", "utmi-pads";
+ nvidia,hssync-start-delay = <9>;
+ nvidia,idle-wait-delay = <17>;
+ nvidia,elastic-limit = <16>;
+ nvidia,term-range-adj = <6>;
+ nvidia,xcvr-setup = <51>;
+ nvidia.xcvr-setup-use-fuses;
+ nvidia,xcvr-lsfslew = <1>;
+ nvidia,xcvr-lsrslew = <1>;
+ nvidia,xcvr-hsslew = <32>;
+ nvidia,hssquelch-level = <2>;
+ nvidia,hsdiscon-level = <5>;
+ status = "disabled";
+ };
+
+ usb@7d004000 {
+ compatible = "nvidia,tegra30-ehci", "usb-ehci";
+ reg = <0x7d004000 0x4000>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ phy_type = "ulpi";
+ clocks = <&tegra_car TEGRA30_CLK_USB2>;
+ nvidia,phy = <&phy2>;
+ status = "disabled";
+ };
+
+ phy2: usb-phy@7d004000 {
+ compatible = "nvidia,tegra30-usb-phy";
+ reg = <0x7d004000 0x4000>;
+ phy_type = "ulpi";
+ clocks = <&tegra_car TEGRA30_CLK_USB2>,
+ <&tegra_car TEGRA30_CLK_PLL_U>,
+ <&tegra_car TEGRA30_CLK_CDEV2>;
+ clock-names = "reg", "pll_u", "ulpi-link";
+ status = "disabled";
+ };
+
+ usb@7d008000 {
+ compatible = "nvidia,tegra30-ehci", "usb-ehci";
+ reg = <0x7d008000 0x4000>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ phy_type = "utmi";
+ clocks = <&tegra_car TEGRA30_CLK_USB3>;
+ nvidia,phy = <&phy3>;
+ status = "disabled";
+ };
+
+ phy3: usb-phy@7d008000 {
+ compatible = "nvidia,tegra30-usb-phy";
+ reg = <0x7d008000 0x4000 0x7d000000 0x4000>;
+ phy_type = "utmi";
+ clocks = <&tegra_car TEGRA30_CLK_USB3>,
+ <&tegra_car TEGRA30_CLK_PLL_U>,
+ <&tegra_car TEGRA30_CLK_USBD>;
+ clock-names = "reg", "pll_u", "utmi-pads";
+ nvidia,hssync-start-delay = <0>;
+ nvidia,idle-wait-delay = <17>;
+ nvidia,elastic-limit = <16>;
+ nvidia,term-range-adj = <6>;
+ nvidia,xcvr-setup = <51>;
+ nvidia.xcvr-setup-use-fuses;
+ nvidia,xcvr-lsfslew = <2>;
+ nvidia,xcvr-lsrslew = <2>;
+ nvidia,xcvr-hsslew = <32>;
+ nvidia,hssquelch-level = <2>;
+ nvidia,hsdiscon-level = <5>;
+ status = "disabled";
+ };
+
cpus {
#address-cells = <1>;
#size-cells = <0>;
--
1.8.1.5
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/