Re: [PATCH v5] media: i2c: tvp7002: add OF support

[naim . dahnoun]

Sent from my iPhone

On 23 Aug 2013, at 18:25, Sylwester Nawrocki <s.nawrocki@xxxxxxxxxxx> wrote:

> On 08/13/2013 03:00 AM, Kumar Gala wrote:
>> On Aug 11, 2013, at 1:25 AM, Lad, Prabhakar wrote:
>> 
>>> From: "Lad, Prabhakar" <prabhakar.csengg@xxxxxxxxx>
>>> 
>>> add OF support for the tvp7002 driver.
>>> 
>>> Signed-off-by: Lad, Prabhakar <prabhakar.csengg@xxxxxxxxx>
>>> ---
> [...]
>>> .../devicetree/bindings/media/i2c/tvp7002.txt      |   53 ++++++++++++++++
>>> drivers/media/i2c/tvp7002.c                        |   67 ++++++++++++++++++--
>>> 2 files changed, 113 insertions(+), 7 deletions(-)
>>> create mode 100644 Documentation/devicetree/bindings/media/i2c/tvp7002.txt
>>> 
>>> diff --git a/Documentation/devicetree/bindings/media/i2c/tvp7002.txt b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt
>>> new file mode 100644
>>> index 0000000..5f28b5d
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt
>>> @@ -0,0 +1,53 @@
>>> +* Texas Instruments TV7002 video decoder
>>> +
>>> +The TVP7002 device supports digitizing of video and graphics signal in RGB and
>>> +YPbPr color space.
>>> +
>>> +Required Properties :
>>> +- compatible : Must be "ti,tvp7002"
>>> +
>>> +Optional Properties:
>> 
>> 
>>> +- hsync-active: HSYNC Polarity configuration for the bus. Default value when
>>> +  this property is not specified is <0>.
>>> +
>>> +- vsync-active: VSYNC Polarity configuration for the bus. Default value when
>>> +  this property is not specified is <0>.
>>> +
>>> +- pclk-sample: Clock polarity of the bus. Default value when this property is
>>> +  not specified is <0>.
>>> +
>>> +- sync-on-green-active: Active state of Sync-on-green signal property of the
>>> +  endpoint.
>>> +  0 = Normal Operation (Active Low, Default)
>>> +  1 = Inverted operation
>> 
>> These seems better than what you have in video-interfaces.txt
> 
> We probably should specify default values in in the common binding description.
> Then duplication could be avoided. Not sure if it's not too late for this, all
> drivers would need to have same default values.
> 
> What's normal and what's inverted depends on a particular device.
> 
>>> +- field-even-active: Active-high Field ID output polarity control of the bus.
>>> +  Under normal operation, the field ID output is set to logic 1 for an odd field
>>> +  (field 1) and set to logic 0 for an even field (field 0).
>>> +  0 = Normal Operation (Active Low, Default)
>>> +  1 = FID output polarity inverted
>>> +
>> 
>> Why the duplication if this is covered in video-interfaces.txt?
> 
> Yes, it would be better to avoid redefining these properties in each specific 
> device's binding. Presumably, for easier matching of DT properties with the
> hardware's description, we could only say in device specific document which
> value of a property corresponds to "normal" and which to "inverted" operation ?
> 
>>> +For further reading of port node refer Documentation/devicetree/bindings/media/
>>> +video-interfaces.txt.
> 
> -- 
> Sylwester Nawrocki
> Samsung R&D Institute Poland
> _______________________________________________
> Davinci-linux-open-source mailing list
> Davinci-linux-open-source@xxxxxxxxxxxxxxxxxxxx
> http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/