Re: [PATCH] serial: 8250_dw: Improve unwritable LCR workaround

[Greg Kroah-Hartman]

On Tue, Sep 24, 2013 at 05:39:09PM -0700, Tim Kryger wrote:
> The Designware UART has a limitation where it ignores writes into the
> LCR if the UART is busy.  The current workaround stashes a copy of the
> last written LCR and writes it back down to the hardware if it receives
> a special busy interrupt which is raised when a write was ignored.
> 
> Unfortunately, interrupts are typically disabled prior to performing a
> sequence of register writes that include the LCR so the point at which
> the retry occurs is too late.  An example is serial8250_do_set_termios()
> where an ignored LCR write results in the baud divisor not being set and
> instead a garbage character is sent out the transmitter.
> 
> Furthermore, since serial_port_out() offers no way to indicate failure,
> a serious effort must be made to ensure that the LCR is actually updated
> before returning back to the caller.  This is difficult, however, as a
> UART that was busy during the first attempt is likely to still be busy
> when a subsequent attempt is made unless some extra action is taken.
> 
> This updated workaround takes the extreme action of clearing the TX/RX
> FIFOs and reading the receive buffer before writing down the LCR in the
> hope that doing so will force the UART into an idle state.  While this
> may seem unnecessarily aggressive, writes to the LCR are used to change
> the baud rate, parity, stop bit, or data length so the data that may be
> lost is likely not important.  Admittedly, this is far from ideal but it
> seems to be the best that can be done given the hardware limitations.
> 
> Lastly, the revised workaround doesn't touch the LCR in the ISR, so it
> avoids the possibility of a "serial8250: too much work for irq" lock up.
> This problem is rare in real situations but can be reproduced easily by
> wiring up two UARTs and running the following commands.
> 
>   # stty -F /dev/ttyS1 echo
>   # stty -F /dev/ttyS2 echo
>   # cat /dev/ttyS1 &
>   [1] 375
>   # echo asdf > /dev/ttyS1
>   asdf
> 
>   [   27.700000] serial8250: too much work for irq96
>   [   27.700000] serial8250: too much work for irq96
>   [   27.710000] serial8250: too much work for irq96
>   [   27.710000] serial8250: too much work for irq96
>   [   27.720000] serial8250: too much work for irq96
>   [   27.720000] serial8250: too much work for irq96
>   [   27.730000] serial8250: too much work for irq96
>   [   27.730000] serial8250: too much work for irq96
>   [   27.740000] serial8250: too much work for irq96
> 
> Signed-off-by: Tim Kryger <tim.kryger@xxxxxxxxxx>
> Reviewed-by: Matt Porter <matt.porter@xxxxxxxxxx>
> Reviewed-by: Markus Mayer <markus.mayer@xxxxxxxxxx>
> ---
>  drivers/tty/serial/8250/8250_dw.c | 57 +++++++++++++++++++++++++++------------
>  1 file changed, 40 insertions(+), 17 deletions(-)

This patch no longer applies to my tty-next tree, can you please refresh
it and resend so that I can apply it?

thanks,

greg k-h
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/