Re: [PATCH 1/2] memory: ti-aemif: introduce AEMIF driver

From: Santosh Shilimkar
Date: Fri Nov 29 2013 - 10:34:11 EST

Next message: Johannes Berg: "Re: [PATCH] net: mac80211: tx.c: be sure of 'sdata->vif.type' mustbe NL80211_IFTYPE_AP when be in NL80211_IFTYPE_AP case"
Previous message: Xose Vazquez Perez: "[PATCH -rc1] s390: increase the NR_CPUS limit"
Next in thread: Grygorii Strashko: "Re: [PATCH 1/2] memory: ti-aemif: introduce AEMIF driver"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Wednesday 20 November 2013 10:46 AM, Ivan Khoronzhuk wrote:
> Add new AEMIF driver for EMIF16 Texas Instruments controller.
> The EMIF16 module is intended to provide a glue-less interface to
> a variety of asynchronous memory devices like ASRA M, NOR and NAND
> memory. A total of 256M bytes of any of these memories can be
> accessed at any given time via four chip selects with 64M byte access
> per chip select.
>
Please add the number of CS info here.

> Synchronous memories such as DDR1 SD RAM, SDR SDRAM and Mobile SDR
> are not supported.
>
> This controller is used on SoCs like Davinci, Keysone2
>

> For more informations see documentation:
> Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
> OMAP-L138 - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf
> Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
>
This information probably can go below ---

> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@xxxxxx>
> ---
> drivers/memory/Kconfig | 11 ++
> drivers/memory/Makefile | 1 +
> drivers/memory/ti-aemif.c | 415 +++++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 427 insertions(+)
> create mode 100644 drivers/memory/ti-aemif.c
>
> diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig
> index 29a11db..cc0e3c8 100644
> --- a/drivers/memory/Kconfig
> +++ b/drivers/memory/Kconfig
> @@ -7,6 +7,17 @@ menuconfig MEMORY
>
> if MEMORY
>
> +config TI_AEMIF
> + bool "Texas Instruments AEMIF driver"
Driver can be build as loadable module as well so fix above.

> + depends on (ARCH_DAVINCI || ARCH_KEYSTONE) && OF
> + help
> + This driver is for the AEMIF module available in Texas Instruments
> + SoCs. AEMIF stands for Asynchronous External Memory Interface and
> + is intended to provide a glue-less interface to a variety of
> + asynchronuous memory devices like ASRAM, NOR and NAND memory. A total
> + of 256M bytes of any of these memories can be accessed at a given
> + time via four chip selects with 64M byte access per chip select.
> +
> config TI_EMIF
> tristate "Texas Instruments EMIF driver"
> depends on ARCH_OMAP2PLUS
> diff --git a/drivers/memory/Makefile b/drivers/memory/Makefile
> index 969d923..d4e150c 100644
> --- a/drivers/memory/Makefile
> +++ b/drivers/memory/Makefile
> @@ -5,6 +5,7 @@
> ifeq ($(CONFIG_DDR),y)
> obj-$(CONFIG_OF) += of_memory.o
> endif
> +obj-$(CONFIG_TI_AEMIF) += ti-aemif.o
> obj-$(CONFIG_TI_EMIF) += emif.o
> obj-$(CONFIG_MVEBU_DEVBUS) += mvebu-devbus.o
> obj-$(CONFIG_TEGRA20_MC) += tegra20-mc.o
> diff --git a/drivers/memory/ti-aemif.c b/drivers/memory/ti-aemif.c
> new file mode 100644
> index 0000000..a4b479a
> --- /dev/null
> +++ b/drivers/memory/ti-aemif.c
> @@ -0,0 +1,415 @@
> +/*
> + * TI AEMIF driver
> + *
> + * Copyright (C) 2010 - 2013 Texas Instruments Incorporated. http://www.ti.com/
> + * Copyright (C) Heiko Schocher <hs@xxxxxxx>
> + * Copyright (C) Ivan Khoronzhuk <ivan.khoronzhuk@xxxxxx>
> + *
You mean author above, right, Please fix that for both emails ids.

> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_platform.h>
> +#include <linux/platform_device.h>
> +
> +#define TA_SHIFT 2
> +#define RHOLD_SHIFT 4
> +#define RSTROBE_SHIFT 7
> +#define RSETUP_SHIFT 13
> +#define WHOLD_SHIFT 17
> +#define WSTROBE_SHIFT 20
> +#define WSETUP_SHIFT 26
> +#define EW_SHIFT 30
> +#define SS_SHIFT 31
> +
> +#define TA(x) ((x) << TA_SHIFT)
> +#define RHOLD(x) ((x) << RHOLD_SHIFT)
> +#define RSTROBE(x) ((x) << RSTROBE_SHIFT)
> +#define RSETUP(x) ((x) << RSETUP_SHIFT)
> +#define WHOLD(x) ((x) << WHOLD_SHIFT)
> +#define WSTROBE(x) ((x) << WSTROBE_SHIFT)
> +#define WSETUP(x) ((x) << WSETUP_SHIFT)
> +#define EW(x) ((x) << EW_SHIFT)
> +#define SS(x) ((x) << SS_SHIFT)
> +
> +#define ASIZE_MAX 0x1
> +#define TA_MAX 0x3
> +#define RHOLD_MAX 0x7
> +#define RSTROBE_MAX 0x3f
> +#define RSETUP_MAX 0xf
> +#define WHOLD_MAX 0x7
> +#define WSTROBE_MAX 0x3f
> +#define WSETUP_MAX 0xf
> +#define EW_MAX 0x1
> +#define SS_MAX 0x1
> +#define NUM_CS 4
> +
> +#define TA_VAL(x) (((x) & TA(TA_MAX)) >> TA_SHIFT)
> +#define RHOLD_VAL(x) (((x) & RHOLD(RHOLD_MAX)) >> RHOLD_SHIFT)
> +#define RSTROBE_VAL(x) (((x) & RSTROBE(RSTROBE_MAX)) >> RSTROBE_SHIFT)
> +#define RSETUP_VAL(x) (((x) & RSETUP(RSETUP_MAX)) >> RSETUP_SHIFT)
> +#define WHOLD_VAL(x) (((x) & WHOLD(WHOLD_MAX)) >> WHOLD_SHIFT)
> +#define WSTROBE_VAL(x) (((x) & WSTROBE(WSTROBE_MAX)) >> WSTROBE_SHIFT)
> +#define WSETUP_VAL(x) (((x) & WSETUP(WSETUP_MAX)) >> WSETUP_SHIFT)
> +#define EW_VAL(x) (((x) & EW(EW_MAX)) >> EW_SHIFT)
> +#define SS_VAL(x) (((x) & SS(SS_MAX)) >> SS_SHIFT)
> +
> +#define NRCSR_OFFSET 0x00
> +#define AWCCR_OFFSET 0x04
> +#define A1CR_OFFSET 0x10
> +
> +#define ACR_ASIZE_MASK 0x3
> +#define ACR_EW_MASK BIT(30)
> +#define ACR_SS_MASK BIT(31)
> +#define ASIZE_16BIT 1
> +
> +#define CONFIG_MASK (TA(TA_MAX) | \
> + RHOLD(RHOLD_MAX) | \
> + RSTROBE(RSTROBE_MAX) | \
> + RSETUP(RSETUP_MAX) | \
> + WHOLD(WHOLD_MAX) | \
> + WSTROBE(WSTROBE_MAX) | \
> + WSETUP(WSETUP_MAX) | \
> + EW(EW_MAX) | SS(SS_MAX) | \
> + ASIZE_MAX)
> +
> +#define DRV_NAME "ti-aemif"
> +
> +/**
> + * structure to hold cs parameters
struct aemif_cs_data : structure to hold cs parameters
> + * @cs: chip-select number
> + * @wstrobe: write strobe width, ns
> + * @rstrobe: read strobe width, ns
> + * @wsetup: write setup width, ns
> + * @whold: write hold width, ns
> + * @rsetup: read setup width, ns
> + * @rhold: read hold width, ns
> + * @ta: minimum turn around time, ns
> + * @enable_ss: enable/disable select strobe mode
> + * @enable_ew: enable/disable extended wait mode
> + * @asize: width of the asynchronous device's data bus
> + */
> +struct aemif_cs_data {
> + u8 cs;
> + u16 wstrobe;
> + u16 rstrobe;
> + u8 wsetup;
> + u8 whold;
> + u8 rsetup;
> + u8 rhold;
> + u8 ta;
> + u8 enable_ss;
> + u8 enable_ew;
> + u8 asize;
> +};
> +
> +/**
> + * structure to hold device data
Prefix structure name here as suggested.

> + * @base: base address of AEMIF registers
> + * @clk: source clock
> + * @clk_rate: clock's rate in kHz
> + * @num_cs: number of assigned chip-selects
> + * @cs_data: array of chip-select settings
> + */
> +struct aemif_device {
> + struct device *dev;
> + void __iomem *base;
> + struct clk *clk;
> + unsigned long clk_rate;
> + u8 num_cs;
> + int cs_offset;
> + struct aemif_cs_data cs_data[NUM_CS];
> +};
> +
> +static struct aemif_device *aemif;
Add one extra line here. From other comment looks
like you are going to get rid of this global which will be
nice.

> +/**
> + * aemif_calc_rate - calculate timing data.
> + * @wanted: The cycle time needed in nanoseconds.
> + * @clk: The input clock rate in kHz.
> + * @max: The maximum divider value that can be programmed.
> + *
> + * On success, returns the calculated timing value minus 1 for easy
> + * programming into AEMIF timing registers, else negative errno.
> + */
> +static int aemif_calc_rate(int wanted, unsigned long clk, int max)
> +{
> + int result;
> +
> + result = DIV_ROUND_UP((wanted * clk), NSEC_PER_MSEC) - 1;
> +
> + dev_dbg(aemif->dev, "%s: result %d from %ld, %d\n", __func__, result,
> + clk, wanted);
> +
> + /* It is generally OK to have a more relaxed timing than requested... */
> + if (result < 0)
> + result = 0;
> +
> + /* ... But configuring tighter timings is not an option. */
> + else if (result > max)
> + result = -EINVAL;
> +
> + return result;
> +}
> +
> +/**
> + * aemif_config_abus - configure async bus parameters
> + * @data: aemif chip select configuration
> + *
> + * This function programs the given timing values (in real clock) into the
> + * AEMIF registers taking the AEMIF clock into account.
> + *
> + * This function does not use any locking while programming the AEMIF
> + * because it is expected that there is only one user of a given
> + * chip-select.
> + *
> + * Returns 0 on success, else negative errno.
> + */
> +static int aemif_config_abus(struct aemif_cs_data *data)
> +{
> + int ta, rhold, rstrobe, rsetup, whold, wstrobe, wsetup;
> + unsigned offset;
> + u32 set, val;
> +
> + offset = A1CR_OFFSET + (data->cs - aemif->cs_offset) * 4;
> +
> + ta = aemif_calc_rate(data->ta, aemif->clk_rate, TA_MAX);
> + rhold = aemif_calc_rate(data->rhold, aemif->clk_rate,
> + RHOLD_MAX);
> + rstrobe = aemif_calc_rate(data->rstrobe, aemif->clk_rate,
> + RSTROBE_MAX);
> + rsetup = aemif_calc_rate(data->rsetup, aemif->clk_rate,
> + RSETUP_MAX);
> + whold = aemif_calc_rate(data->whold, aemif->clk_rate,
> + WHOLD_MAX);
> + wstrobe = aemif_calc_rate(data->wstrobe, aemif->clk_rate,
> + WSTROBE_MAX);
> + wsetup = aemif_calc_rate(data->wsetup, aemif->clk_rate,
> + WSETUP_MAX);
> +
> + if (ta < 0 || rhold < 0 || rstrobe < 0 || rsetup < 0 ||
> + whold < 0 || wstrobe < 0 || wsetup < 0) {
> + dev_err(aemif->dev, "%s: cannot get suitable timings\n",
> + __func__);
> + return -EINVAL;
> + }
> +
> + set = TA(ta) | RHOLD(rhold) | RSTROBE(rstrobe) | RSETUP(rsetup) |
> + WHOLD(whold) | WSTROBE(wstrobe) | WSETUP(wsetup);
> +
> + set |= (data->asize & ACR_ASIZE_MASK);
> + if (data->enable_ew)
> + set |= ACR_EW_MASK;
> + if (data->enable_ss)
> + set |= ACR_SS_MASK;
> +
> + val = readl(aemif->base + offset);
> + val &= ~CONFIG_MASK;
> + val |= set;
> + writel(val, aemif->base + offset);
> +
> + return 0;
> +}
> +
> +static inline int aemif_cycles_to_nsec(int val)
> +{
> + return ((val + 1) * NSEC_PER_MSEC) / aemif->clk_rate;
> +}
> +
> +/**
> + * aemif_get_hw_params - function to read hw register values
> + * @data: ptr to cs data
> + *
> + * This function reads the defaults from the registers and update
> + * the timing values. Required for get/set commands and also for
> + * the case when driver needs to use defaults in hardware.
> + */
> +static void aemif_get_hw_params(struct aemif_cs_data *data)
> +{
> + u32 val, offset;
> + offset = A1CR_OFFSET + (data->cs - aemif->cs_offset) * 4;
> +
> + val = readl(aemif->base + offset);
> + data->ta = aemif_cycles_to_nsec(TA_VAL(val));
> + data->rhold = aemif_cycles_to_nsec(RHOLD_VAL(val));
> + data->rstrobe = aemif_cycles_to_nsec(RSTROBE_VAL(val));
> + data->rsetup = aemif_cycles_to_nsec(RSETUP_VAL(val));
> + data->whold = aemif_cycles_to_nsec(WHOLD_VAL(val));
> + data->wstrobe = aemif_cycles_to_nsec(WSTROBE_VAL(val));
> + data->wsetup = aemif_cycles_to_nsec(WSETUP_VAL(val));
> + data->enable_ew = EW_VAL(val);
> + data->enable_ss = SS_VAL(val);
> + data->asize = val & ASIZE_MAX;
> +}
> +
> +/**
> + * of_aemif_parse_abus_config - parse CS configuration from DT
> + * @np: device node ptr
> + *
> + * This function update the emif async bus configuration based on the values
> + * configured in a cs device binding node.
> + */
> +static int of_aemif_parse_abus_config(struct device_node *np)
> +{
> + struct aemif_cs_data *data;
> + unsigned long cs;
> + u32 val;
> +
> + if (kstrtoul(np->name + 2, 10, &cs) < 0) {
> + dev_dbg(aemif->dev, "cs name is incorrect");
> + return -EINVAL;
> + }
> +
> + if (cs - aemif->cs_offset >= NUM_CS || cs < aemif->cs_offset) {
> + dev_dbg(aemif->dev, "cs number is incorrect %lu", cs);
> + return -EINVAL;
> + }
> +
> + if (aemif->num_cs >= NUM_CS) {
> + dev_dbg(aemif->dev, "cs count is more than %d", NUM_CS);
> + return -EINVAL;
> + }
> +
> + data = &aemif->cs_data[aemif->num_cs++];
> + data->cs = cs;
> +
> + /* read the current value in the hw register */
> + aemif_get_hw_params(data);
> +
> + /* override the values from device node */
> + of_property_read_u8(np, "ti,cs-ta", &data->ta);
> + of_property_read_u8(np, "ti,cs-rhold", &data->rhold);
> + of_property_read_u16(np, "ti,cs-rstrobe", &data->rstrobe);
> + of_property_read_u8(np, "ti,cs-rsetup", &data->rsetup);
> + of_property_read_u8(np, "ti,cs-whold", &data->whold);
> + of_property_read_u16(np, "ti,cs-wstrobe", &data->wstrobe);
> + of_property_read_u8(np, "ti,cs-wsetup", &data->wsetup);
> + if (!of_property_read_u32(np, "ti,bus-width", &val))
> + if (val == 16)
> + data->asize = 1;
> + data->enable_ew = of_property_read_bool(np, "ti,cs-ew");
> + data->enable_ss = of_property_read_bool(np, "ti,cs-ss");
> + return 0;
> +}
> +
> +static const struct of_device_id aemif_of_match[] = {
> + { .compatible = "ti,davinci-aemif", },
> + { .compatible = "ti,keystone-aemif", },
> + { .compatible = "ti,omap-L138-aemif", },
> + {},
> +};
> +
Looks like you are yet to update the patches from
previous comments. Did I miss v2 or you haven't posted
that yet ?

Regards,
Santosh

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Johannes Berg: "Re: [PATCH] net: mac80211: tx.c: be sure of 'sdata->vif.type' mustbe NL80211_IFTYPE_AP when be in NL80211_IFTYPE_AP case"
Previous message: Xose Vazquez Perez: "[PATCH -rc1] s390: increase the NR_CPUS limit"
Next in thread: Grygorii Strashko: "Re: [PATCH 1/2] memory: ti-aemif: introduce AEMIF driver"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]