[PATCH v3 5/5] ARM: dts: AM43xx-epos-evm: DT entries for ti-usim and phy

From: Satish Patel
Date: Wed May 28 2014 - 04:58:14 EST


- Board specific DT entries for TI's USIM - smart card controller of AM43xx
platfrom.These entries are used by USIM driver for various configurations.

- Shutdown line of NXP phy is maped to GPIO5. So enabling same to have support
for NXP phy.

- i2c2 pinmux configuration - NxP tda8026 phy is connected to i2c2 lines

Signed-off-by: Satish Patel <satish.patel@xxxxxx>
---
arch/arm/boot/dts/am43x-epos-evm.dts | 31 +++++++++++++++++++++++++++++++
1 file changed, 31 insertions(+)

diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts
index 167dbc8..ecc8b1a 100644
--- a/arch/arm/boot/dts/am43x-epos-evm.dts
+++ b/arch/arm/boot/dts/am43x-epos-evm.dts
@@ -115,6 +115,18 @@
>;
};

+ usim0_default: usim0_default {
+ pinctrl-single,pins = <
+ /* USIM 0 */
+ 0x1B4 (SLEWCTRL_FAST | PULL_DISABLE | MUX_MODE8) /* CLK0 */
+ 0x1B0 (SLEWCTRL_FAST | PULL_DISABLE | MUX_MODE8) /* CLK1 */
+ 0x1B8 (SLEWCTRL_FAST | INPUT_EN | PULL_DISABLE | MUX_MODE8) /* DATA0 */
+ 0x1BC (SLEWCTRL_FAST | INPUT_EN | PULL_DISABLE | MUX_MODE8) /* DATA1 */
+ 0x1C8 (SLEWCTRL_FAST | INPUT_EN | PULL_UP | MUX_MODE8) /* IRQn */
+ >;
+ };
+
+
spi0_pins: pinmux_spi0_pins {
pinctrl-single,pins = <
0x150 (PIN_INPUT | MUX_MODE0) /* spi0_clk.spi0_clk */
@@ -238,10 +250,24 @@
};
};

+&usim0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usim0_default>;
+ phy = <&tda8026>;
+ phy-slots = <1>;
+ status = "okay";
+};
+
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
status = "okay";
+ tda8026: tda8026@48 {
+ compatible = "nxp,tda8026";
+ reg = <0x48>;
+ shutdown-gpio = <&gpio5 19 GPIO_ACTIVE_HIGH>; /* Bank5, pin19 */
+ interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+ };
};

&gpio0 {
@@ -260,6 +286,11 @@
status = "okay";
};

+&gpio5 {
+ status = "okay";
+};
+
+
&elm {
status = "okay";
};
--
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/